The Gas-to-Particle Heat Transfer and Hydrodynamics in Spouted Bed Drying of Sawdust

Abstract

This article presents experimental results for spouted bed drying of sawdust, carried out in a full-scale as well as in a laboratory-scale dryer using air as well as steam as drying media. The aim is to present design parameters for a spouted-bed sawdust dryer that can be used by the industry in designing full-scale dryers. A hydrodynamically stable spouted jet spouted bed was obtained. The heat transfer characteristics of the bed were represented in terms of a volumetric heat transfer coefficient (VHC). When sawdust is dried in a spouted bed, the mean VHC is increasing up to fiber saturation level (20–25% wb) from 40 to 110 W/m³ K. The VHC decreases with the residence time and with an increased static bed height. Gas temperature profiles are also presented for the bottom part of the drying chamber.     

使用导流管对连续喷动干燥器的影响

在欧洲市场,对使用诸如团块状的生物质燃料的关注日益增长。本文给出了使用带有不同类型导流管的连续喷动干燥锯末的实验数据。对不同进口和出口温度下湿锯末干燥进行了研究。在喷动干燥器中,干燥能力取决于热流量大小。实验结果表明,导流管能够提高干燥能力。此外,导流管的设计对热流量利用有影响。     

A MATHEMATICAL MODEL FOR CONTINUOUS DRYING OF GRAINS IN A SPOUTED BED DRYER

A mathematical model for a continuous spouted bed dryer has been presented to predict moisture content, air and grain temperatures as well as energy consumption. To better understand the interactive influence of processes in each region of the spouted bed, solution schemes for the spout and downcomer were treated separately. The behavior of dryer was investigated experimentally and found that the dryer behaved differently from an ideal plug flow. The drying rate as simulated by the model is almost constant during grain movement in the dryer. Absence of airflow in the downcomer leads to a tempering process that takes place in the downcomer while intense heat and mass transfer occurs mainly in the spout due to the high airflow rate there. Furthermore, by considering the predicted grain temperature history as one of the indicators of product quality, one can, in principle, design appropriate successive processes in a continuous spouted bed dryer to minimize product damage.     

A MATHEMATICAL MODEL FOR CONTINUOUS DRYING OF GRAINS IN A SPOUTED BED DRYER

ABSTRACT

A mathematical model for a continuous spouted bed dryer has been presented to predict moisture content, air and grain temperatures as well as energy consumption. To better understand the interactive influence of processes in each region of the spouted bed, solution schemes for the spout and downcomer were treated separately. The behavior of dryer was investigated experimentally and found that the dryer behaved differently from an ideal plug flow. The drying rate as simulated by the model is almost constant during grain movement in the dryer. Absence of airflow in the downcomer leads to a tempering process that takes place in the downcomer while intense heat and mass transfer occurs mainly in the spout due to the high airflow rate there. Furthermore, by considering the predicted grain temperature history as one of the indicators of product quality, one can, in principle, design appropriate successive processes in a continuous spouted bed dryer to minimize product damage.     

Drying characteristics of a draft tube spouted bed

Using the results of earlier work on the flow pattern of gas and solids in a draft-tube spouted bed, the drying characteristics of such a spouted bed are discussed. Paddy (unpeeled rice) was dried in a 30 cm bed with a 5.5 cm draft tube and temperatures and moisture content of solid and gas phase were measured as a function of drying time at various points in the system. It appears that the (constant) drying rate is determined by the heat transfer in the recirculation zone (just above the air inlet) and in the draft tube. After the short and rapid heating in the tube, the temperature and moisture gradients in the particle equilibrate in the annulus. It is concluded that a draft-tube spouted bed is a promising dryer design for heat-sensitive particles with slow intra-particle mass transfer coefficients.     

An Experimental Study on the Influence of Using a Draft Tube in a Continuous Spouted Bed Dryer

Further increasing the production of processed biofuel also increases the demands on drying capacity. With the aim of increasing the heat capacity flow, experimental tests have been performed on the process of drying sawdust in a continuous spouted bed dryer with nine different draft tube designs. The results showed that a draft tube with an increased length and an increased disengagement height decreased the dry substances’ flow rate throughout the dryer. The results also showed that the mass of the material in the dryer was approximately the same in all the tests. This means that the draft tubes, no matter their size, do not influence the amount of material in the dryer.     

Modeling of Moisture and Temperature Changes of Wheat during Drying in a Triangular Spouted Bed Dryer

A mathematical model of temperature and wheat moisture content distribution inside a triangular spouted bed dryer was developed. The model is based on analysis of heat and mass transfer inside the dryer. In addition to that, an empirical bulk density model has been developed for wheat and included in the drying simulation. A laboratory-scale triangular spouted bed (TSB) dryer was used to dry wheat grain to validate the model. The dryer was divided into three sections, namely spouting, downcomer, and fountain. A series of drying runs were conducted to record moisture and temperature profile. There were two distinct regions observed during wheat drying. A constant rate period was observed during the initial drying stage and the falling rate period took place at the later drying stage. Initial moisture content and operating drying temperature governed the timing of transition from constant rate period to falling rate period. The model can be used to accurately predict the moisture content of wheat during drying. The temperature prediction inside the TSB dryer was less accurate, especially at high temperatures due to heat losses in the experimental dryer. Further studies are needed to improve the accuracy of this model, especially with regard to the temperature prediction.     

Modeling of Moisture and Temperature Changes of Wheat during Drying in a Triangular Spouted Bed Dryer

A mathematical model of temperature and wheat moisture content distribution inside a triangular spouted bed dryer was developed. The model is based on analysis of heat and mass transfer inside the dryer. In addition to that, an empirical bulk density model has been developed for wheat and included in the drying simulation. A laboratory-scale triangular spouted bed (TSB) dryer was used to dry wheat grain to validate the model. The dryer was divided into three sections, namely spouting, downcomer, and fountain. A series of drying runs were conducted to record moisture and temperature profile. There were two distinct regions observed during wheat drying. A constant rate period was observed during the initial drying stage and the falling rate period took place at the later drying stage. Initial moisture content and operating drying temperature governed the timing of transition from constant rate period to falling rate period. The model can be used to accurately predict the moisture content of wheat during drying. The temperature prediction inside the TSB dryer was less accurate, especially at high temperatures due to heat losses in the experimental dryer. Further studies are needed to improve the accuracy of this model, especially with regard to the temperature prediction.     

SPOUTED AND SPOUT-FLUIDIZED BEDS FOR GRAM DRYING

The objectives of this work are to analyze the drying performance of conical-cylindrical spouted bed (CSB) dryers for three different grains (rice, corn and wheat), and to compare the drying efficiency of CSB dryers with that of spout-fluid bed (SFB) dryers. A PC-program was developed for: (I) -optimization of the CSB dryer dimensions; (2) -simulation of drying grains in the optimized CSB dryer (including start-up period); and, (3) -analysis of the drying performance in a similar SFB dryer.

The liquid diffusion model is used to describe the falling rate drying period. Semi-empirical correlations available in the literature as well as information obtained in the authors' laboratory for spouted and spout-fluidized beds of grains are used to describe the aerodynamic parameters.

The results are presented in terms of the size of the dryer, energy consumption, air handling requirement, drying characteristics etc for different drying conditions. The drying effeciency in a CSB is compared with that in a similar SFB for different grain feed rates and drying temperatures.     

HEAT AND MASS TRANSFER DURING DRYING OF A LIQUID FILM FROM THE SURFACE OF A SINGLE INERT PARTICLE

ABSTRACT

This paper presents the results of theoretical and experimental studies on drying of aqueous suspensions of finely dispersed solids sprayed over the surface of an inert ceramic sphere. The effects of temperature and air velocity on kinetics of heat and mass transfer as well as peeling off the layer of a dry material from the sphere surface are described. The mathematical model of a drying process based on simplified ?gradientless? approach to transfer phenomena is proposed. The adequacy of the model developed for drying of the wet coat from a single sphere to the real drying process taking place in a bed of particulate carrier is confirmed by results of drying of several organic dyestuffs in an industrial spouted bed dryer with inert particles.     

A TWO-REGION MATHEMATICAL MODEL FOR BATCH DRYING OF GRAINS IN A TWO-DIMENSIONAL SPOUTED BED

A two-region non-equilibrium model of a two-dimensional spouted bed dryer has been developed. The model, based on heat and mass transfer interactions between the spout and downcomer regions, predicts the air and grain temperatures and moisture content throughout each elementary thin layer of grain in the spouted bed. The model was validated with the experimental results on batch drying of corn. Drying and heating processes are shown to occur in both the spout and downcomer regions. Overall, the agreement between experimental and simulated results is satisfactory.     

A TWO-REGION MATHEMATICAL MODEL FOR BATCH DRYING OF GRAINS IN A TWO-DIMENSIONAL SPOUTED BED

A two-region non-equilibrium model of a two-dimensional spouted bed dryer has been developed. The model, based on heat and mass transfer interactions between the spout and downcomer regions, predicts the air and grain temperatures and moisture content throughout each elementary thin layer of grain in the spouted bed. The model was validated with the experimental results on batch drying of corn. Drying and heating processes are shown to occur in both the spout and downcomer regions. Overall, the agreement between experimental and simulated results is satisfactory.     

Experimental Study of the Heat and Mass Transfer During Drying in a Fluidized Bed Dryer

Drying curves obtained in a pilot-scale fluidized bed dryer using biological source solids (sawdust, soya and fish meal) were used to estimate the parameters involved in heat and mass transfer phenomenas: heat transfer coefficient and moisture diffusivity coefficient. Parameters involved in mass transfer were estimated from drying models based on diffusional mechanisms and others that in addition consider internal and external resistance to the mass transfer. The estimate ef ective diffusivity coefficient was between 2x10-11 to lx10 (m2/s) for the considered products. Heat transfer coefficient was estimated from drying data points in the constant drying rate period when the external resistance to the mass transfer controls the process.     

SPOUTED AND SPOUT-FLUIDIZED BEDS FOR GRAM DRYING

The objectives of this work are to analyze the drying performance of conical-cylindrical spouted bed (CSB) dryers for three different grains (rice, corn and wheat), and to compare the drying efficiency of CSB dryers with that of spout-fluid bed (SFB) dryers. A PC-program was developed for: (I) -optimization of the CSB dryer dimensions; (2) -simulation of drying grains in the optimized CSB dryer (including start-up period); and, (3) -analysis of the drying performance in a similar SFB dryer.

The liquid diffusion model is used to describe the falling rate drying period. Semi-empirical correlations available in the literature as well as information obtained in the authors' laboratory for spouted and spout-fluidized beds of grains are used to describe the aerodynamic parameters.

The results are presented in terms of the size of the dryer, energy consumption, air handling requirement, drying characteristics etc for different drying conditions. The drying effeciency in a CSB is compared with that in a similar SFB for different grain feed rates and drying temperatures.     

Drying Of Pastes In Spouted Beds Of Inert Particles: Design Criteria And Modeling

The drying of pastelike materials can be performed well in spouted beds (SB) of inert particles. In this work the drying performance of pastes in conical pastes in conical spouted beds is analyzed as a function of column dimensions, fluid flow characteristics and paste properties. imulated data on fluid flow together with the experimental results on drying of different pastelike materials are presented and discussed to provide criteria for the design of a conical spouted bed dryer for suspensions.     

HYDRODYNAMICS AND MASS TRANSFER IN A SPOUTED BED DRYER

The disposal of sludge generated by water treatment plants poses major financial and environmental problems. Drying of the sludge is an essential pan of any disposal process which may include incinerating, landfilling or upgrading. In the present study, experiments were carried out to investigate the drying of sludge in a spouted bed and to characterize the hydrodynamics and mass transfer mechanisms. The effect of bed moisture content on the minimum spouting velocity (U_ms) was examined for sludge granules. U_ms was found to increase with increasing the moisture content of the sludge particles. The gas phase mass transfer coefficient in the dryer was determined using porous calcined alumina particles and the results were compared with predictions by correlations available in the literature. The existing correlations gave poor predictions for the mass transfer coefficient. A new correlation for the mass transfer coefficient in a spouted bed dryer was developed based on the experimental results.     

Experimental Study of the Heat and Mass Transfer During Drying in a Fluidized Bed Dryer

ABSTRACT

Drying curves obtained in a pilot-scale fluidized bed dryer using biological source solids (sawdust, soya and fish meal) were used to estimate the parameters involved in heat and mass transfer phenomenas: heat transfer coefficient and moisture diffusivity coefficient. Parameters involved in mass transfer were estimated from drying models based on diffusional mechanisms and others that in addition consider internal and external resistance to the mass transfer. The estimate ef ective diffusivity coefficient was between 2x10-11 to lx10 (m2/s) for the considered products. Heat transfer coefficient was estimated from drying data points in the constant drying rate period when the external resistance to the mass transfer controls the process.     

Drying Of Pastes In Spouted Beds Of Inert Particles: Design Criteria And Modeling

ABSTRACT

The drying of pastelike materials can be performed well in spouted beds (SB) of inert particles. In this work the drying performance of pastes in conical pastes in conical spouted beds is analyzed as a function of column dimensions, fluid flow characteristics and paste properties. imulated data on fluid flow together with the experimental results on drying of different pastelike materials are presented and discussed to provide criteria for the design of a conical spouted bed dryer for suspensions.     

Drying Process on Inert Particles in Mechanically Spouted Bed Dryer

ABSTRACT

Suspensions, slurries and paste-like materials can be dried in the Mechanically Spouted Bed ( MSB) dryer with men packing. The circulation of the men particles characteristic of classical spouted beds is provided with a houseless conveyor screw mounted in the vertical axis of the bed. Radioactive isotopic tracer technique was used for measurement of the cycle time distribution ( CTD) of the spherical inert particles as a function of the operational parameters of drying. The variances ( σ²) of the CTDs and the particle velocity m the various zones of the MSB dryer were calculated. The circulation of the mert particles can be characterised by nearly plug flow. According to the physical model of drying on inert packing the heat and mass transfer coefficients were calculated. Que to the relativeiy uniform film-like, wet coating formed on the surface of the spheical inert particles, the drying process may be characterised with the constant rate of drying. A method has been elaborated for calculation of drying time, hereby the partial processes of drying on inert particles can be synchronised.     

MODELING AND SIMULATION OF AIRFLOW IN SPOUTED BED DRYERS

This paper presents an axisymmetric three-dimensional semi-empirical model that describes the airflow in both the spout and annular regions. Both the pressure and air velocity distributions can be calculated at any point inside the dryer. Thus, the effect of the fluid dynamics on the heat and mass transfer coefficients and, consequently, on the drying process, can be evaluated. The finite element method was used to solve the model. Pressure distributions were measured for several conditions in which stable spouted bed flow regime was attained. Simulated pressure distributions agreed well with experimental data.