首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
在研究读写器和射频标签通信过程的基础上,结合EPC C1G2协议以及ISO/IEC18000-6协议,采用VHDL语言设计出一种应用于超高频段的射频标签数字电路.对电路的系统结构和模块具体实现方法进行了描述.基于0.18 μm CMOS工艺标准单元库,采用EDA工具对电路进行了前端综合和后端物理实现.给出的仿真结果表明该电路符合协议要求,综合后的电路规模约为11000门,功耗约为35 μW.该电路可应用于超高频段的各种RFID标签的数字部分.  相似文献   

2.
陈刚  田翠翠  舒海翔  陈剑 《微电子学》2015,45(4):516-520
通过对UHF频段EPC Global Class1 Generate2协议进行分析,详细论述了符合协议要求的被动式无源射频身份识别(RFID)标签的数字电路系统方案,并提出了一种新颖的、针对RFID标签的数字基带低功耗电路。在0.18 μm CMOS工艺环境下,使用Synopsys工具对电路进行前端综合和后端物理实现,同时对电路的功耗进行了简要的分析。仿真及测试结果表明,该标签数字基带电路功能符合协议要求。  相似文献   

3.
章少杰 《电子器件》2009,32(6):1035-1039
本文从设计符合EPCTM C1G2协议的超高频无源射频识别标签芯片的角度出发,对RFID标签芯片模拟前端电路进行设计.通过对各个关键电路的功耗与电源进行优化,实现了一个符合协议要求的低电压、低功耗的超高频无源RFID标签芯片的模拟前端.该UHF RFID标签模拟前端设计采用SMIC 0.18 μm EEPROM CMOS工艺库.仿真结果表明,标签芯片模拟前端的整体功耗控制在2.5 μW以下,工作电源可低至1 V,更好地满足了超高频无源射频识别标签芯片应用需求.  相似文献   

4.
李营刚 《电子世界》2012,(12):52-53
本文根据协议的相关要求,设计了无源UHF RFID标签芯片模拟前端电路,并重点对标签芯片模拟前端的关键技术进行了优化,实现了标签芯片模拟前端电路。最终,电路的仿真结果表明标签芯片的模拟前端电压较为稳定,且功耗较小,稳定的时钟频率能够帮助系统进行正确的输入信号解调,实现了协议要求的电路设计。  相似文献   

5.
基于FPGA的RFID板级标签设计与实现   总被引:1,自引:1,他引:0  
在分析射频识别原理和特点的基础上,讨论超高频射频识别系统中电子标签设计技术,并采用EP1C6Q240FPGA对超高频电子标签进行了板级设计及其实现.利用Verilog语言实现了标签数字电路,并在板级标签中进行了验证.测试结果表明,该设计实现了ISO18000-6C标准的标签读写功能,读写性能优异,为下一步设计出符合该标准的电子标签芯片提供了有力保证.  相似文献   

6.
朱卓娅  程剑平  魏同立   《电子器件》2005,28(4):798-800,805
设计了一种单节锂离子电池保护电路。分析了系统的特点和应用要求,提出了采用亚阈值电路和由内部数字信号来控制模拟电路工作状态的方法,优化了系统的功耗。电路采用0.6肛mUMC数字电路工艺实现。HSPICE模拟结果表明,该电路不仅能满足锂离子电池应用中的保护要求,而且具有较低的电流功耗,在正常和Standby模式下。系统消耗电流分别3.23μA和0.15μA。  相似文献   

7.
阎永平  王玲 《电子科技》2011,24(2):63-65
基于对某型汽油发电机组控制保护电路的分析,提出了一种采用数字电路和MCU对该控制保护电路进行改进的设计方案.实验表明,该方案实现了对机组的控制与保护功能,优化了设计、满足了技术指标要求.  相似文献   

8.
基于FPGA的可重构性,提出了一种基于数字电路的二值忆阻器仿真器。与模拟电路忆阻器仿真器相比,所提出基于数字电路的忆阻器仿真器易于重新配置,与它所基于的数学模型表现出很好的匹配性,符合忆阻器仿真器所有要求的特点。实现了基于该仿真器的与门、或门、加法器及三人表决器。使用Altera Quartus II和ModelSim工具对仿真器功能和基于该仿真器实现的逻辑电路进行验证。给出所有设计电路的原理图、仿真结果和FPGA资源消耗。仿真结果表明,该二值忆阻器仿真器相比其他数字电路忆阻器仿真器具有更少的硬件资源消耗,更适合用于大规模忆阻器阵列研究。  相似文献   

9.
本文设计了一种在低电压下工作的用于射频标签的上电复位电路。此电路一方面采用了一种新型电平检测模块,可以实现精准的电平检测;另一方面采用了一种新型延迟模块,该模块可在0.8V—5V电源电压下工作,可实现100nS到1mS之间的延时;此外,为了降低功耗,电路在产生上电复位信号将利用数字电路产生一个反馈信号来关断整个电路。本文采用smic0.18um的工艺,利用cadence对其功能进行仿真,结果表明该电路可在1.2V工作电压下进行有效复位,并且可以快速的二次复位,复位脉冲宽度为20us左右,功耗极低,完全满足RFID标签的要求。  相似文献   

10.
提出了一种应用于UHF RFID无源标签芯片解调电路的设计方法,该方法结构简单,能适用于不同协议,并具有低功耗、高稳定度和高灵敏度等优点。文中给出了基于TSMC 0.18μm CMOS混合信号工艺的设计实现方法及其在spectre仿真环境下的仿真结果。并通过MPW项目进行了流片验证。  相似文献   

11.
DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.  相似文献   

12.
This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel's.  相似文献   

13.
The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.  相似文献   

14.
Today, micro-system technology and the development of new MEMS (Micro-Electro-Mechanical Systems) are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.  相似文献   

15.
The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.  相似文献   

16.
From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.  相似文献   

17.
It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output(MIMO) communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.  相似文献   

18.
Waveguide multilayer optical card (WMOC) is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling & processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic (VB) language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.  相似文献   

19.
The effect of laser microbeam trapping the bioparticles has been appfied widely in the biology .However the micromechanism of the acting that realizes the laser-microbeam trapping bioparticles is still lacking. In this paper ,the act microchenism of the gradiant force of laser microbeam for the bioparticles is analysed by means of quantum theory ,The result accords with our experiment.  相似文献   

20.
We have fabricated the white organic light-emitting devices (WOLEDs) based on 4,4' -bis(2,2 -diphenyl vinyl)-1,1' - biphenyl (DPVBi) and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene (rubrene). The device structure is ITO/2T-NATA (20 nm)/NPBX (20 nm)/CBP: x%Ir(ppy)3:0.5% rubrene (8 nm)/NPBX (5 nm)/DPVBi (30 nm)/Alq(30 nm)/LiF(0.5 nm)/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris (2-phenylpyridine) iridium [Ir(ppy)3], acts as a yellow light-emitting layer, and N,N' -bis- (1-naphthyl)- N,N' -diphenyl -1, 1' -biphenyl-4,4' -diamine (NPBX) acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir (PPY)3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号