原位氧化硅钝化层对氧化钒薄膜光电特性的影响

氧化硅(SiOx)原位钝化层对氧化钒(VOx)薄膜电学特性的影响分析旨在改善像元微桥结构的光学吸收特性,提高热敏VOx薄膜层的方阻和电阻温度系数(TCR)稳定性。采用离子束溅射沉积50 nm VOx薄膜后,紧接着沉积30 nm SiOx钝化层。通过原位残余气体分析仪(RGA)和衬底温度控制,调节氧化钒薄膜中的氧含量,分析了VOx单层膜、SiOx/VOx双层膜的电学特性随工艺温度的变化规律,原位残余气体分析仪(RGA)和150℃加温工艺提高了VOx热敏层薄膜的方阻和电阻温度系数稳定性。     

PTCDA表面射频磁控溅射ITO薄膜的特性研究

将氧化铟锡(ITO)溅射淀积在PTCDA/玻璃衬底表面,利用原子力显微镜(AFM)、四探针和紫外可见分光光度计分别测量薄膜的表面形貌、电阻率和透光率.结果表明:衬底温度对ITO在PTCDA上的淀积有着与在其他衬底上淀积所不同的影响,提高衬底温度淀积ITO并没有提高薄膜的结晶度;溅射功率的提高有利于ITO电阻率的下降,但是功率过高会破坏ITO薄膜的特性:ITO膜厚度的增加导致其电阻率减小.     

有机玻璃衬底磁控溅射ITO膜的制备与性能研究

在低温条件下采用直流磁控溅射法在有机玻璃(PMMA)衬底上制备了ITO薄膜。分别采用分光光度计、四探针测试仪研究了底涂层、衬底温度、氧流量、溅射时间对PMMA上沉积的ITO薄膜性能的影响。研究结果表明:涂覆底涂层有助于ITO成膜;衬底温度影响薄膜的方块电阻值;适当增大O2流量可以提高薄膜的透射率,但过高的O2流量降低薄膜的导电性;溅射时间延长,方块电阻值减小。优化工艺后制备的ITO薄膜为非晶态膜,可见光平均透过率达83.5%,方块电阻为22Ω/□。     

射频磁控溅射ITO薄膜对TOPCon太阳电池光电性能的影响

通过射频(RF)磁控溅射分别在光学玻璃基底上和多晶硅薄膜层上沉积了氧化铟锡(ITO)薄膜,采用Hall效应测试仪测试了ITO薄膜的电阻率和载流子浓度等参数,研究溅射功率和溅射时间等参数对ITO薄膜的光电特性影响.测试多晶Si对称结构沉积ITO薄膜前后及退火后的隐开路电压和反向饱和电流密度等参数,研究ITO薄膜对n型晶硅...     

有机玻璃衬底磁控溅射ITO膜的制备与性能研究

在低温条件下采用直流磁控溅射法在有机玻璃(PMMA)衬底上制备了ITO薄膜。分别采用分光光度计、四探针测试仪研究了底涂层、衬底温度、氧流量、溅射时间对PMMA上沉积的ITO薄膜性能的影响。研究结果表明: 涂覆底涂层有助于ITO成膜; 衬底温度影响薄膜的方块电阻值; 适当增大O2流量可以提高薄膜的透射率, 但过高的O2流量降低薄膜的导电性; 溅射时间延长, 方块电阻值减小。优化工艺后制备的ITO薄膜为非晶态膜, 可见光平均透过率达83.5%, 方块电阻为22Ω/□。     

AZO透明导电薄膜的制备

采用射频磁控溅射法在玻璃衬底上制备了ZnO:Al(AZO)透明导电薄膜,并借助XRD、SEM等表征方法,研究了溅射功率和衬底温度对薄膜结构、表面形貌及光电特性的影响。结果表明,制备薄膜的最佳溅射功率和衬底温度分别为180 W、200℃,在此条件下制备的AZO薄膜具有明显的c轴(002)择优取向,其最低方块电阻为18/□,在可见光范围内的平均透光率超过91%,且透明导电性能优于目前平板显示器的要求,有望取代现在市场上的主流氧化铟锡(ITO)薄膜。     

PLD法制备ITO导电薄膜及其性能

为了研制可用于高温环境下进行应变测量的应变层,采用脉冲激光沉积(PLD)法在陶瓷基底上制备了氧化铟锡(ITO)薄膜。研究了PLD法中不同基底温度对ITO薄膜显微结构、电学性能以及阻温特性的影响。采用X射线衍射仪(XRD)测试了薄膜的晶体结构,通过四点探针测量法测得薄膜的薄层电阻,采用场发射扫描电子显微镜(FESEM)对薄膜进行表面形貌分析。结果发现制备的ITO薄膜呈现出体心立方(BCC)结构,且沿(222)晶面优先生长,薄膜的晶粒尺寸随着基底温度的升高而增加,ITO薄膜的电学性能受基底温度的影响显著,电阻率随着衬底温度的升高而降低。最后,搭建测试平台在25~1050℃内测试了不同基底温度下制备的ITO薄膜的电阻温度系数(TCR)。结果表明,ITO薄膜的电阻温度系数随基底温度的升高而降低,在基底温度为600℃下制备的ITO薄膜具有最小的TCR值,为-259.575×10^-6℃^-1。     

氩氧比与退火温度对磁控溅射VO2薄膜结构与电学性能的影响

采用反应直流磁控溅射法,通过调控溅射过程中的氩氧比,在石英玻璃衬底上制备了氧化钒薄膜,研究了溅射气氛及后处理条件对其微结构与电学性能的影响.经450和500℃退火,薄膜中易形成VO2,而550℃退火时薄膜中会形成大量非4价的钒氧化物.薄膜在较高温度500℃下退火时结晶度增加,但薄膜颗粒之间的间隙更为明显,导致电阻率显著提高;同时其电阻率-温度曲线的热滞回线宽度较窄,在加热过程中相转变温度较高.当氩氧比中氧含量增加时,沉积的VO2薄膜中生成了少量非4价的钒氧化物.结果表明,反应磁控溅射法制备的氧化钒薄膜的微结构、电阻率、相变温度等特性与氩氧比和后退火温度密切相关.     

直流磁控溅射ITO薄膜的正交试验分析

利用直流磁控溅射系统制备ITO薄膜,采用正交试验表格L32(48)安排试验.测试了薄膜的方阻和透过率,分析了8个工艺参数对薄膜电光特性的影响,其中沉积气压、氩氧流量比和退火温度的影响最大.分析得到优化工艺参数为:沉积气压2×133.322 4 mPa、氩氧流量比16∶0.5、退火温度427 ℃、靶基间距15、退火时间1 h、溅射功率300 W、退火氛围为真空、沉积温度227 ℃.在此工艺参数下制备的ITO薄膜方阻为17 Ω/□,电阻率为1.87×10-4Ω·cm,在可见光区域平均透过率为85.13%.     

退火温度对ZnO掺杂ITO薄膜性能的影响

利用电子束蒸镀方法,在K8玻璃衬底上沉积ZnO掺杂ITO(ZnO-ITO)与ITO薄膜。研究不同退火温度对ZnO-ITO薄膜的微观结构的影响;对比分析了在不同退火温度条件下,ZnO-ITO和无掺杂ITO薄膜的光电性能。结果发现,ZnO-ITO薄膜具有较大的晶粒尺寸,随着退火温度的上升,晶体结构得到改善,表面粗糙度减小,薄膜的光电性能显著提高。ZnO-ITO薄膜经过500℃退火后得到最佳的综合性能,其表面均方根粗糙度(RMS)为32.52nm,电阻率为1.43×10-4Ω.cm;对442nm波长的光,透射率可达98.37%;与ITO薄膜相比,ZnO-ITO薄膜具有显著的抗PEDOT:PSS溶液腐蚀的能力。     

Technology innovation and process integrations for sub-100nm gate patterning

This paper presents a brief overview of the Applied Centura(R)DPS(R)system,configured with silicon etch DPS Ⅱ chamber, with emphasis on discussing tuning capability for CD uniformity control. It also presents the studies of etch process chemistry and film integration impact for an overall successful gate patterning development. Discussions will focus on resolutions to key issues, such as CD uniformity, line-edge roughness, and multilayer film etching integration.     

White organic light-emitting devices based on fac tris（2- phenylpyridine） iridium sensitized 5,6,11,12-tetraphenylnap -hthacene

We have fabricated the white organic light-emitting devices （WOLEDs） based on 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1＇ - biphenyl （DPVBi） and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene （rubrene）. The device structure is ITO/2T-NATA （20 nm）/NPBX （20 nm）/CBP： x%Ir（ppy）3：0.5% rubrene （8 nm）/NPBX （5 nm）/DPVBi （30 nm）/Alq（30 nm）/LiF（0.5 nm）/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris （2-phenylpyridine） iridium [Ir（ppy）3], acts as a yellow light-emitting layer, and N,N＇ -bis- （1-naphthyl）- N,N＇ -diphenyl -1, 1＇ -biphenyl-4,4＇ -diamine （NPBX） acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir （PPY）3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.     

Complete approach to automatic identification and subpixel center location for ellipse feature

To meet the need of automatic image features extraction with high precision in visual inspection, a complete approach to automatic identification and sub-pixel center location for similar-ellipse feature is proposed. In the method, the feature area is identified automatically based on the edge attribute, and the sub-pixel center location is accomplished with the leastsquare algorithm. It shows that the method is valid, practical, and has high precision by experiment. Meanwhile this method can meet the need of instrumentation of visual inspection because of easy realization and without man-machine interaction.     

小角度扩展相关性近似算法分析

本论文提出一种在多天线MIMO信道相关性建模中小角度扩展近似理论算法,并应用于分析MIMO系统性能。分析中分别对三种不同角能量分布情况下的空间相关性研发快速近似计算法,并同时提出双模(Bi-Modal)角能量分布情况下的近似运算。通过分析这些新方法的近似效率,可以得到计算简单、复杂度低、而且符合实际的MIMO相关信道矩阵,对系统级的快速高效计算法的研究和系统级的评估以及误差分析具有重要的意义。     

A Versatile Mixed-Signal Pin Approach for Cost-Effective Test of Automotive ICs

Integrated circuits (ICs) intended for increasingly sophisticated automotive applications bring unique test demands. Advanced ICs for applications such as highly integrated automatic braking system (ABS) and airbag controllers combine high voltage digital channels, significant VI demands and precise timing capability. Along with continued missioncritical reliability concerns, the trend toward higher voltage operation and increased device integration requires specialized test capabilities able to extend across the wide operating ranges found in automotive applications. Among these capabilities, automotive test requirements increasingly dictate a need for a cost-effective versatile mixed-signal pin electronics with very high data rates reaching up to 50MHz with a voltage swing of-2 V to +28 V.     

Optical vibration and deviation measurement of rotating machine parts

It is of interest to get appropriate information about the dynamic behaviour of rotating machinery parts in service. This paper presents an approach of optical vibration and deviation measurement of such parts. Essential of this method is an image derotator combined with a high speed camera or a laser doppler vibrometer （LDV）.     

社长序言（英文）

正Happy New Year!As we step into a new year,we take a look back at the key feature topics covered in China Communications over the past 12 months and set out our expecta-     

Call for Papers

正Introduction Jointly sponsored by the China Institute of Communications(CIC)and the IEEE Communications Society(IEEE ComSoc)since the year 2013,China Communications,currently,is aiming to gradually realise the transition from journal to magazine content and style.     

INTEGRATION OF OPTICAL AND WIRELESS NETWORKS

正For a long time,optical and wireless systems/net-works are developed in separate communities witha few attempts for in-depth convergence.In fact,it prom-ises many advantages to combine the optical and wire-less technologies in the levels of systems and networks.Recently,both academia and industry have made manyefforts to enter a new phase of development to take op-tical and wireless systems as fully integrated networks.To provide high bandwidth and reliable service for bothfixed and mobile users,a well-designed network must     

Call for Papers—Feature Topic,Vol.12,No.3,2015

正Smart Grid Communications The electric power industry is undergoing profound changes as the industry aims to capture the promise of a smart grid for a sustainable energy future.Enabled by the advanced sensing devices such as Phasor Measurement Units(PMUs),increasingly powerful