Sb2S3/TiO2纳米管异质结阵列的制备和光电性能

结合水热法和阳极氧化法合成了Sb2S3/TiO2纳米管异质结阵列,采用场发射扫描电子显微镜、X射线衍射谱表征了异质结阵列的形貌和晶体结构.暗态下的电流-电压曲线表明Sb2S3/TiO2纳米管异质结阵列具有整流效应.相比于纯的TiO2纳米管阵列,Sb2S3/TiO2纳米管异质结阵列的光电性能有了显著地提升:在AM1.5标准光强作用下,光电转换效率从0.07％增长到0.40％,表面光电压响应范围从紫外光区拓宽至可见光区.结合表面光电压谱和相位谱,分析了Sb2S3/TiO2纳米管异质结阵列中光生载流子的分离和传输性能.     

TiO2基染料敏化太阳能电池的表面修饰及性能研究

采用水热法制备TiO₂浆料,用La(NO₃)₃溶 液浸泡TiO₂薄膜获得修饰电极。用X射线光电子能谱(XPS) 和扫描电子显微镜(SEM)对修饰电极的主要成分及形貌进行表征的结果显示,电极薄膜分为 上下两层,表 面包覆层粒径较大,为La₂O₃颗粒;下层颗粒粒径较小,为TiO₂颗粒。电流-电压测 试结果显示,与修饰 前相比,用La(NO₃)₃溶液浸泡30min获得的膜电极性能最优,使 开路电压和短路电流分别提高了6.8%和 18.5%。电化学阻抗谱(EIS)测试结果表明,相同偏压下,TiO₂/La ₂O₃电极界面复合电阻比TiO₂要大,说明 La₂O₃包覆层在一定程度上抑制了界面的电子复合,改善了电池的光电化学性能。     

低温处理的TiO2纳米颗粒薄膜作为缓冲层的有机光伏电池

通过溶胶凝胶法(sol-gel)合成了TiO₂纳米颗 粒(NPs),制备了结构为 ITO/PEDOT:PSS/P3HT:PCBM/TiO₂/Al的有机太阳能电池(OSC)器件。通过优化阴极缓冲 层TiO₂NPs的 热处理温度,考察了温度以及溶剂对TiO₂NPs薄膜的光学性能、形貌结构和电学 性能的影响,并研究了其对OSC性能的影响及作用机理。实验发现,TiO₂NPs处理温度 为80℃时,器件 的效率达到了2.52%。相对于参比器件,器件的光电转换效率(PCE) 、填充因子(FF)分别提高了60%、64.7%。     

基于wx-AMPS的锑基双结叠层太阳电池的模拟优化

锑基薄膜太阳电池具有原材料丰富、制备方法简单 和光电性能优异等优势。将宽带隙 Sb₂S₃电池与窄带隙Sb₂Se₃电池组成叠层太阳电池能够进一步提高光谱能量利用率 ,增强器 件性能。基于此,采用wx-AMPS软件对锑基双结叠层薄膜太阳电池进行了仿真优化。仿 真结果显示,要想获得高效的叠层太阳电池首先需要高质量的吸收层,吸收层缺陷态要低于 10¹⁵ cm－3才能够将光生载流子充分转换为电流。除此 之外,子电池厚度的调制能够平衡顶 底电池的光谱响应,在叠层太阳电池的优化中也十分重要。基于此,绘制了不同顶底电 池厚度叠层太阳电池性能参数的等高线图,为叠层太阳电池的实验优化制备提供指导,并最 终在顶底电池厚度分别为700 nm和2500 nm的情况下,得到24.60%的锑基双结叠层太阳电 池 的最高光电转换效率。研究结果体现了新型锑基薄膜叠层太阳电池结构的优势和发展 潜力。     

TiO2掺杂浓度对倒装白光数码管光色性能的影响

采用热压法将TiO₂按一定计量比掺入AB混合胶制备折射胶层,在芯片和荧光粉胶层 间利用甩胶旋 涂工艺添加折射胶层,封装成白光数码管;对样品的光色性能进行了测试和机 理分析。结 果表明,折射层中掺杂TiO₂颗粒浓度为0.3%时,白光数码管单笔段 光通量达到了最高值175 lm,比TiO₂浓度为0%时提高了约为7.5%。在相同测试条件下,掺杂0.3%浓度TiO₂颗粒的倒装白光数码管比传统点胶 白光数码管平均光通量提高了约为6.5%,平均色温下降约为 9.6%,出光一致性更理想。TiO₂颗粒的掺入不 仅提高了器件光通量,降低了色温,同时为白光数码管实现远程荧光粉涂覆工艺提供了一种 有效的途径。     

空芯带隙型光子晶体光纤残余双折射特性研究

采用磁控溅射法, 在玻璃基底上一步沉积In₂S₃薄膜。研究了溅射功率对In₂S₃薄膜的成分、结构、表面形貌和光电性能的影响。结果表明: 所制备的所有薄膜均为β-In₂S₃, 无杂相存在, 且具有(222)面择优生长特性。溅射功率对薄膜的成分、厚度和结晶度具有明显的影响, 并因此影响薄膜的光学和电学性能。薄膜在100W沉积时最接近化学计量比, 薄膜的透过率随着溅射功率增大在500nm波段附近显著提高, 禁带宽度达到2.45eV, 同时电流密度增大两个数量级。     

非稀土红色荧光粉Mn4+:Li2TiO3发光特性研究

利用高温固相法成功合成了非稀土类红色荧光粉 Mn⁴⁺:Li₂TiO₃,并对所制得的样品进行X射线衍射(XRD)、吸收谱和荧光发射谱等 表征。在波长为475nm的LED蓝光照射时,获得了最大强度位于〖J P 〗682nm波长处的红色荧光,量 子效率约为10%,其对应Mn⁴⁺自旋²Eg→⁴A 2g。计 算了晶体场强度因子Dq和Racah参数B、C,并据此分析了Mn⁴⁺在Li₂TiO₃中的电 子云重排效应。通 过改变掺杂浓度,分析了Mn⁴⁺掺杂在Li₂TiO₃中的浓度淬灭效 应。最后进行了LED白光性能 测试。     

GaInP2/Ge异质结外延材料特性分析

研制了一种基于Ge衬底的异质结热光伏(TPV)电池 ,并且在Ge衬底上用金属有机化学气相沉积(MOCVD)法外延单晶材料GaInP₂和GaAs,对GaInP₂/Ge异质结界面进行了断面扫描电镜(SEM)、X射线衍射(XRD)、电化学电 容电压(ECV)和光致荧光(PL)谱的测试分析,研究了基于 Ge衬底的异质结n-GaInP₂/p-Ge界面的结构、光学和电学特性,得到了高质量、宽禁带 的单晶外延层,与Ge衬底晶格匹配良好,利于更多光子进入到吸收层,为制备高效率TPV电 池打下良好基础。     

介稳态TiCl4醇水溶液水解制备TiO2致密层及其在无机-有机杂化异质结钙钛矿太阳电池中的应用

致密层作为钙钛矿太阳电池的重要组成部分, 对其制备方法, 工艺及微结构等性质的研究对提高钙钛矿太阳电池的光伏性能具有重要影响. 本文利用介稳态的TiCl₄醇水溶液作为前驱体溶液, 通过旋涂水解制备TiO₂致密层, 并研究了前驱体溶液不同醇水比对致密层微结构及其相应太阳电池光伏性能的影响. 结果表明, 将2 mol.L_-1的TiCl₄的水溶液按醇水体积比3:1的比例用异丙醇稀释后所制备的TiO₂致密层其厚度为126 nm, 且相应的太阳电池取得最高的光电转换效率10.6 %.     

29种天然染料敏化的太阳电池的性能研究

采用超声波萃取法从29种天然植物中提取染料, 测试天然染料的紫外-可见光(UV-vis)吸收光谱,探讨天然染料所 含的色素种类。采用水热法制备了TiO₂薄膜电极,用所提取的29种天然染料敏化TiO₂光 电极并将其组装成染料敏化太阳电池(DSSCs)。测试天然染料敏化的DSSCs 的光电性能结果显示,天然染料敏化的DSSCs的开路 电压Voc为0.46~0.64 V,短路电流I_sc为0.07~3.61mA· cm－2,其中山竹皮敏 化的DSSCs光电性能最佳,对应的I_sc和光电转换 效率η分 别为3.61mA·cm－2和2.13%。从天然 染料中挑选出7种不同吸收波段色素的染料进行协同敏化,UV-vis吸收光谱测试结 果显示混合染料的吸收峰一般有微小偏移。光电性能测试结果表明,协同敏化后的DSSCs的 性能一般都介于天然染料单独敏 化的两个DSSCs的性能之间,其中山竹皮和芥蓝协同敏化的DSSCs的η最高,为1.70%。对实验结果进行深入分析,探讨提高天然染料 敏化的DSSCs光电性能的途径。     

TiO_2纳米管阵列对染料敏化太阳能电池性能的影响

通过恒压阳极氧化法在Ti箔表面制备了结构规整的TiO2纳米管阵列,研究了氧化时间和退火温度对纳米管阵列的尺寸和晶体结构的影响。用制得的纳米管阵列电极组装了染料敏化太阳能电池(DSSC),研究了纳米管长度、退火温度和电极面积对DSSC光电性能的影响。结果表明,纳米管管径和壁厚均与氧化时间无关,而纳米管长度则随着氧化时间延长而增加。在450℃及更低温度退火时,纳米管中只出现锐钛矿相;而在500℃退火时,纳米管中则又出现了金红石相。由厚度为27μm、退火温度为450℃的纳米管阵列电极组装成的DSCC具有最佳的光电转化性能。DSCC的光电转化效率随电极面积的增加而降低。     

Nb掺杂TiO_2纳米管的制备及其氢敏特性

以Ti35Nb合金为基材,通过阳极氧化和中温热处理制备了Nb掺杂TiO2纳米管阵列。通过掩模版和磁控溅射技术在纳米管阵列表面形成了Pt电极,随后在低浓度H2气氛中测试了Nb掺杂TiO2纳米管阵列的氢敏性能。实验结果表明阳极氧化温度是影响纳米管生长的一个重要因素,在阳极氧化电压为15V和阳极氧化温度为30℃的条件下可以获得均匀开口的非晶纳米管阵列。将非晶纳米管在450℃热处理后可以获得锐钛矿结构纳米管阵列。氢传感实验结果表明,Nb掺杂TiO2纳米管对低浓度气氛具有室温氢敏特性。以上实验结果表明,通过合金化设计和阳极氧化可以制备出具有室温氢传感特性的掺杂纳米管阵列。     

阳极氧化工艺参数和缓冲液对TiO2纳米管阵列形貌的影响

摘要：采用恒压阳极氧化法,在氢氟酸/ 醋酸水溶液中,以钛片为阳极制备了垂直的TiO2纳米管阵列。通过电解液浓度、电压、氧化时间和缓冲液等阳极氧化参数的选择,调节了纳米管的长度和形貌等特征。     

Morphology dependence of TiO2 nanotube arrays on anodization variables and buffer medium

Vertically oriented TiO2 nanotube arrays were prepared by potentiostatic anodization of Ti foils in HF/acetic acid (HAC) aqueous solution. Anodization variables including anodization electrolyte concentration, anodization volt-age, anodization time and buffer medium can be chosen and adjusted to manipulate the nanotube arrays to give the required length and morphology.     

ZnO-Coated TiO2 Nanotube Arrays for a Photoelectrode in Dye-Sensitized Solar Cells

In dye-sensitized solar cells, highly ordered TiO₂ nanotube arrays as a photoelectrode have higher charge collection efficiencies than a nanoparticle-based structure due to their faster charge percolation and slower recombination of electrons. Highly ordered TiO₂ nanotube arrays were grown by anodic oxidation of 0.5-mm-thick titanium foil. To increase the conversion efficiency of dye-sensitized solar cells with TiO₂ nanotube arrays, the surface of the TiO₂ nanotube arrays was modified by zinc oxide thin films. The ZnO thin film was formed by atomic layer deposition. The thin film was conformal on the inner and outer walls of TiO₂ nanotube arrays. ZnO thin film improved the short circuit current (J _sc) and open circuit voltage (V _oc) due to increasing specific surface area from particulates of ZnO thin film and increasing the surface charge induced from the isoelectric point. The power conversion efficiency of dye-sensitized solar cells with ZnO thin film on 4.5-μm-thick TiO₂ nanotube arrays was 1.43%. Microstructure and phase were observed by scanning electron microscopy, x-ray diffractometry, and transmission electron microscopy.     

Electrochemical Method for Synthesis of a ZnFe2O4/TiO2 Composite Nanotube Array Modified Electrode with Enhanced Photoelectrochemical Activity

An electrode with intimate and well‐aligned ZnFe₂O₄/TiO₂ composite nanotube arrays is prepared via electrochemical anodization of pure titanium foil in fluorine‐containing ethylene glycol, followed by a novel cathodic electrodeposition method. The deposition of ZnFe₂O₄ is promoted in the self‐aligned, vertically oriented TiO₂ nanotube arrays but minimized at the tube entrances. Thus, pore clogging is prevented. Environmental scanning electron microscopy, energy‐dispersive X‐ray spectra, high‐resolution transmission electron microscopy, X‐ray diffraction patterns, and X‐ray photoelectron spectroscopy indicate that the as‐prepared samples are highly ordered and vertically aligned TiO₂ nanotube arrays with ZnFe₂O₄ nanoparticles loading. The TiO₂ nanotubes are anatase with the preferential orientation of <101> plane. Enhanced absorption in both UV and visible light regions is observed for the composite nanotube arrays. The current–voltage curve of ZnFe₂O₄‐loaded TiO₂ nanotube arrays reveals a rectifying behavior. The enhanced separation of photoinduced electrons and holes is demonstrated by surface photovoltage and photocurrent measurements. Meanwhile, the photoelectrochemical investigations verify that the ZnFe₂O₄/TiO₂ composite nanotube array modified electrode has a more effective photoconversion capability than the aligned TiO₂ nanotube arrays alone. In addition, the photoelectrocatalytic ability of the novel electrode is found enhanced in the degradation of 4‐chlorophenol.     

以CuPc为空穴传输层的染料敏化异质结电池的特性研究

制备以酞菁铜CuPc为空穴传输层,有机染料-二氢吲哚D102（C37H30N2O3S2）为敏化染料的染料敏化异质结电池DSH（Dye-sensitized heterojunction solar cells）。研究不同厚度CuPc空穴传输层：40 nm、80 nm和120 nm的电池的性能,得到在其厚度为40 nm时,电池的Jsc=248.3μA/cm2,Voc=0.61V,=0.042%（80 mW/cm2氙灯测试）。对比采用I3-/I-氧化-还原对为液态电解质的染料敏化TiO2纳米晶太阳电池,分析以CuPc为空穴传输层的DSH电池效率较低的原因。     

A multifunctional photoanode made of titania submicrospheres and titania nanoparticles modified titania nanotube arrays on FTO glass for dye-sensitized solar cells

We have proposed a novel engineered multifunctional photoanode which consists of one-dimensional (1D) TiO₂ nanotube arrays modified by TiO₂ nanoparticles as a bottom layer and three-dimensional (3D) TiO₂ submicrospheres as a top layer by a simple one-time chemical bath deposition method. This 1D-3D bilayer photoanode simultaneously possesses the incompatible features such as high specific surface area, pronounced light-scattering ability, and fast electron transport. The novel 1D-3D bilayer photoanode demonstrates a power conversion efficiency (PCE) of 6.93%, leading to a 26.5% increment of PCE compared with that of TiO₂ bare nanotube arrays (5.48%).     

Sb掺杂BaTiO_3的电磁及微波吸收特性研究

以BaCO3、TiO2、Sb2O3为原料,采用固相法制备了Sb掺杂BaTiO3样品,借助XRD、Raman光谱以及矢量网络分析仪等分析测试手段对所制样品的晶相、晶格常数、电磁性能及微波吸收特性进行了表征。结果表明:低掺杂Sb的样品均为单一四方相BaTiO3晶体,结晶良好;随着w(Sb2O3)的增大,晶格常数减小;与未掺杂的BaTiO3相比,Sb掺杂BaTiO3的反射损耗明显提高,且反射峰向低频方向偏移;当w(Sb2O3)为0.6%时,制得BaTiO3的反射损耗在3.7 GHz处达到最大值–28.2 dB。     

Solvothermal synthesis of Bi2O3/BiVO4 heterojunction with enhanced visible-light photocatalytic performances

Novel, three-dimensional, flower-like Bi2O3/BiVO4 heterojunction photocatalysts have been prepared by the combination of homogeneous precipitation and two-step solvothermal method followed by thermal solution of NaOH etching process. The as-obtained samples were fully characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, Brunauer-Emmett-Teller surface area, and UV-vis diffusereflectance spectroscopy in detail. The crystallinity, microstructure, specific surface area, optical property and photocatalytic activity of samples greatly changed depending on solvothermal reaction time. The photocatalytic activities of samples were evaluated on the degradation of methyl orange (MO) under visible-light irradiation. The Bi2O3/BiVO4 exhibited much higher photocatalytic activities than pure BiVO4 and conventional TiO2 (P25). The result revealed that the three-dimensional heterojunction played a critical role in the separation of the electron and hole pairs and enhancement of the interfacial charge transfer efficiency, which was responsible for the enhanced photocatalytic activity.