Thermoelectric properties of Bi<Subscript>2</Subscript>Te<Subscript>2.4</Subscript>Se<Subscript>0.6</Subscript> solid solutions of different particle-size composition

The thermoelectric properties of n-type Bi₂Te_2.4Se_0.6 solid solution prepared by the vacuum hot pressing of powder mixtures with different particle sizes are investigated. The powders were prepared by the mechanical grinding of ingots and melt spinning. The microstructure and fracture pattern of a sample cleavage surface are analyzed using scanning electron microscopy and optical microscopy. The thermoelectric characteristics (the Seebeck coefficient, electrical conductivity, and thermal conductivity) are measured at room temperature and in the temperature range of 100–700 K.     

Influence of Nanoinclusions on Thermoelectric Properties of <Emphasis Type="Italic">n</Emphasis>-Type Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> Nanocomposites

n-Type Bi₂Te₃ nanocomposites with enhanced figure of merit, ZT, were fabricated by a simple, high-throughput method of mixing nanostructured Bi₂Te₃ particles obtained through melt spinning with micron-sized particles. Moderately high power factors were retained, while the thermal conductivity of the nanocomposites was found to decrease with increasing weight percent of nanoinclusions. The peak ZT values for all the nanocomposites were above 1.1, and the maximum shifted to higher temperature with increasing amount of nanoinclusions. A maximum ZT of 1.18 at 42°C was obtained for the 10 wt.% nanocomposite, which is a 43% increase over the bulk sample at the same temperature. This is the highest ZT reported for n-type Bi₂Te₃ binary material, and higher ZT values are expected if state-of-the-art Bi₂Te_3−x Se _x materials are used.     

Effects of SiC Nanodispersion on the Thermoelectric Properties of <Emphasis Type="Italic">p</Emphasis>-Type and <Emphasis Type="Italic">n</Emphasis>-Type Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Alloys

Polycrystalline p-type Bi_0.5Sb_1.5Te₃ and n-type Bi₂Te_2.7Se_0.3 thermoelectric (TE) alloys containing a small amount (vol.% ≤5) of SiC nanoparticles were fabricated by mechanical alloying and spark plasma sintering. It was revealed that the effects of SiC addition on TE properties can be different between p-type and n-type Bi₂Te₃-based alloys. SiC addition slightly increased the power factor of the p-type materials by decreasing both the electrical resistivity (ρ) and Seebeck coefficient (α), but decreased the power factor of n-type materials by increasing both ρ and α. Regardless of the conductivity type, the thermal conductivity was reduced by dispersing SiC nanoparticles in the Bi₂Te₃-based alloy matrix. As a result, a small amount (0.1 vol.%) of SiC addition increased the maximum dimensionless figure of merit (ZT _max) of the p-type Bi_0.5Sb_1.5Te₃ alloys from 0.88 for the SiC-free sample to 0.97 at 323 K, though no improvement in TE performance was obtained in the case of n-type Bi₂Te_2.7Se_0.3 alloys. Importantly, the SiC-dispersed alloys showed better mechanical properties, which can improve material machinability and device reliability.     

Thermoelectric properties of Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> ribbons prepared by melt spinning

The results of studying the thermoelectric properties of p-type Bi_0.5Sb_1.5Te₃ alloy samples prepared by melt spinning quenching are presented. The material after melt spinning is shaped as thin ribbons and has a quasi-amorphous structure. The thermoelectric properties (thermoelectric power and electrical resistance) and crystallization processes of as-prepared melt-spun ribbons are studied at 300–800 K for the first time. The stability range of the initial state, the crystallization-onset temperature, and the effect of thermal annealing on the thermoelectric-power factor of the alloy are determined.     

Specific thermoelectric properties of lightly doped Bi<Subscript>2</Subscript>(TeSe)<Subscript>3</Subscript> solid solutions

Electrical and thermoelectric properties of a lightly doped n-Bi₂Te_2.7Se_0.3 solid solution have been studied in the temperature range 77–300 K. The results are compared with data for the compound PbTe_0.9Se_0.1 with a similar magnitude of the Seebeck coefficient S at 84 K. Along with lower thermal conductivity, Bi₂Te_2.7Se_0.3 has a higher electrical conductivity σ and a much weaker temperature dependence. As a result, the power coefficient S ²σ in optimal samples begins to decrease only when the density of minority carriers becomes significant. In this case, |S| considerably exceeds the standard value of 200 μV/K. The reduction of the electron density reduces the thermoelectric figure of merit Z at its maximum and slightly lowers the temperature of the maximum; therefore, the expected effect on the average value of Z in the range 77–300 K is absent. Similar behavior is observed in Bi₂Te_2.88Se_0.12, although the effect is less pronounced. The experimental results are discussed taking into account possible changes in the dominant scattering mechanisms, carrier density, and electron energy spectrum. __________ Translated from Fizika i Tekhnika Poluprovodnikov, Vol. 38, No. 7, 2004, pp. 811–815. Original Russian Text Copyright ? 2004 by Konstantinov, Prokof’eva, Ravich, Fedorov, Kompaniets.     

Influence of Element Substitution on Corrosion Behavior of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Compounds

Atmospheric water may condense on the surface of Bi₂Te₃-based compounds constituting the Peltier module, depending on the operating environment used. In the stage of disposal, Bi₂Te₃-based compounds may come into contact with water in waste disposal sites. There are very few publications about the influence of condensed water on Peltier modules. Bi₂Te₃-Sb₂Te₃ or Bi₂Te₃-Bi₂Se₃ pseudo binary system compounds are used as p-type material or n-type material, respectively. The lattice distortion will be induced in the crystal of Bi₂Te₃-based compounds by element substitution due to the reduction in their thermal conductivity. However, the influence of element substitution on the corrosion behavior of Bi₂Te₃-based compounds remains unclear. In this study, the influence of element substitution on the corrosion behavior of Bi₂Te₃-based compounds with practical compositions has been investigated. Bi_0.5Sb_1.5Te₃ or Bi₂Te_2.85Se_0.15 was prepared by the vertical Bridgman method. The electrochemical properties at room temperature were evaluated by cyclic voltammetry in a standard three-electrode cell. The working electrolyte was a naturally aerated 0.6 or 3.0 mass% NaCl solution. From the tendency for corrosion potential for all the samples, the corrosion sensitivity of ternary compounds was slightly higher than that of binary compounds. From the trend of current density, it was found that Bi_0.5Sb_1.5Te₃ had a corrosion resistance intermediate between Bi₂Te₃ and Sb₂Te₃. On the other hand, corrosion resistance was affected despite a small amount of Se substitution, and the corrosion resistance of Bi₂Te_2.85Se_0.15 was close to or lower than that of Bi₂Se₃. From the observation results of the corrosion products, the trends of morphology and composition of corrosion products for Bi_0.5Sb_1.5Te₃ or Bi₂Te_2.85Se_0.15 were consistent with those of Sb₂Te₃ or Bi₂Se₃, respectively. From the results of x-ray photoelectron spectroscopy for the electrolyte after testing, the possibility that a corrosion product diffuses to the environment including the salt was suggested in Bi_0.5Sb_1.5Te₃. However, the amount of dissolved corrosion product was very low, and the chemical stability of the corrosion product was not changed or improved by element substitution.     

Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> Superlattices Grown by Nanoalloying

In this work, Bi₂Te₃-Sb₂Te₃ superlattices were prepared by the nanoalloying approach. Very thin layers of Bi, Sb, and Te were deposited on cold substrates, rebuilding the crystal structure of V₂VI₃ compounds. Nanoalloyed super- lattices consisting of alternating Bi₂Te₃ and Sb₂Te₃ layers were grown with a thickness of 9 nm for the individual layers. The as-grown layers were annealed under different conditions to optimize the thermoelectric parameters. The obtained layers were investigated in their as-grown and annealed states using x-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive x-ray (EDX) spectroscopy, transmission electron microscopy (TEM), and electrical measurements. A lower limit of the elemental layer thickness was found to have c-orientation. Pure nanoalloyed Sb₂Te₃ layers were p-type as expected; however, it was impossible to synthesize p-type Bi₂Te₃ layers. Hence the Bi₂Te₃-Sb₂Te₃ superlattices consisting of alternating n- and p-type layers showed poor thermoelectric properties.     

Improvement of Thermoelectric Power Factor of Hydrothermally Prepared Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> Compared with its Solvothermally Prepared Counterpart

We report on the successful hydrothermal synthesis of Bi_0.5Sb_1.5Te₃, using water as the solvent. The products of the hydrothermally prepared Bi_0.5 Sb_1.5Te₃ were hexagonal platelets with edges of 200–1500 nm and thicknesses of 30–50 nm. Both the Seebeck coefficient and electrical conductivity of the hydrothermally prepared Bi_0.5Sb_1.5Te₃ were larger than those of the solvothermally prepared counterpart. Hall measurements of Bi_0.5Sb_1.5Te₃ at room temperature indicated that the charge carrier was p-type, with a carrier concentration of 9.47 × 10¹⁸ cm⁻³ and 1.42 × 10¹⁹ cm⁻³ for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively. The thermoelectric power factor at 290 K was 10.4 μW/cm K² and 2.9 μW/cm K² for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively.     

Thermoelectric Properties of Co<Subscript>4</Subscript>Sn<Subscript>6</Subscript>Se<Subscript>6</Subscript> Ternary Skutterudites

A ternary ordered variant of the skutterudite structure, the Co₄Sn₆Se₆ compound, was prepared. Polycrystalline samples were prepared by a modified ceramic method. The electrical conductivity, the Seebeck coefficient and the thermal conductivity were measured over a temperature range of 300–800 K. The undoped Co₄Sn₆Se₆ compound was of p-type electrical conductivity and had a band gap E _g of approximately 0.6 eV. The influence of transition metal (Ni and Ru) doping on the thermoelectric properties was studied. While the thermal conductivity was significantly lowered both for the undoped Co₄Sn₆Se₆ compound and for the doped compounds, as compared with the Co₄Sb₁₂ binary skutterudite, the calculated ZT values were improved only slightly.     

Preparation and Thermoelectric Properties of Nanoporous Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>-Based Alloys

n-Type nanoporous Bi₂Te₃-based thermoelectric materials with different porosity ratios have been prepared by spark plasma sintering (SPS). The microstructure and phase morphology have been analyzed by x-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM), and the thermoelectric properties of the SPS samples have been measured. Experimental results show that the nanoporous structures lying in the sheet layers and among the plate grains of the Bi₂Te₃ bulk material can lead to an increase in the Seebeck coefficient and a decrease in the thermal conductivity, thus leading to an enhanced figure of merit.     

Effect of Composition on Thermoelectric Properties in PbTe-Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> Composites

The solidification of alloys in the Bi₂Te₃-PbTe pseudobinary system at off- and near-eutectic compositions was investigated for their microstructure and thermoelectric properties. Dendritic and lamellar structures were clearly observed due to the phase separation and the existence of a metastable ternary phase. In this system, three phases with different compositions were observed: binary Bi₂Te₃, PbTe, and metastable PbBi₂Te₄. The Seebeck coefficient, electrical resistivity, and thermal conductivity of ternary alloys as well as binary compounds were measured. The phonon thermal conductivities of Pb-Bi-Te alloys were lower than those in binary PbTe and Bi₂Te₃, which could have resulted from the increased interfacial area between phases due to the existence of the metastable ternary phase and the resultant phase separation.     

Thermoelectric Properties of Spark Plasma-Sintered In<Subscript>4</Subscript>Se<Subscript>3</Subscript>-In<Subscript>4</Subscript>Te<Subscript>3</Subscript>

We report the thermoelectric properties of spark plasma-sintered In₄Se₃-In₄Te₃ materials. For comparison, pure In₄Se₃ and In₄Se₃ (80 wt.%)/In₄Te₃ (20 wt.%) mixture samples were prepared. In₄Se₃ and In₄Te₃ powders were synthesized by a conventional melting process in evacuated quartz ampoules, and a spark plasma method was used for the sintering of the pure In₄Se₃ and mixture samples. Thermoelectric and structural characterizations were carried out, and the mixing effect of In₄Se₃ and In₄Te₃ on the thermoelectric properties was investigated.     

High-Performance (Ag<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>SbTe<Subscript><Emphasis Type="Italic">x</Emphasis>/2+1.5</Subscript>)<Subscript>15</Subscript>(GeTe)<Subscript>85</Subscript> Thermoelectric Materials Prepared by Melt Spinning

A new preparation process combining melt spinning and hot pressing has been developed for the (Ag _x SbTe _x/2+1.5)₁₅(GeTe)₈₅ (TAGS-85) system. Compared with samples prepared by the traditional air-quenching and hot-pressing method, electrical conductivity and thermal conductivity are lowered. The thermoelectric performance of the TAGS-85 samples varied with changing Ag content and reached the highest ZT of 1.48 when x was 0.8 for the melt-spun sample, compared with the maximum ZT of 1.36 for the air-quenched sample. The Seebeck coefficient of the melt-spun TAGS-85 alloys was improved, while both the electrical conductivity and thermal conductivity were decreased. The net result of this process is to effectively enlarge the temperature span of ZT > 1, which will benefit industrial application.     

Effect of Electric Current on the Performance of Bi<Subscript>1.2</Subscript>Sb<Subscript>4.8</Subscript>Te<Subscript>9</Subscript> Thermoelectric Material Prepared by a Field-Activated Pressure-Assisted Sintering Process

Field-activated pressure-assisted sintering (FAPAS) was applied to sinter Bi_1.2Sb_4.8Te₉ thermoelectric materials under different conditions, including no-current sintering (NCS), low-density current sintering (LCS), and high-density current sintering (HCS). The effect of the current density on the final thermoelectric performance of the products was investigated. Applying a higher-density electric current and shorter dwell time can improve the thermoelectric performance of the sample by increasing its electric conductivity and decreasing its thermal conductivity. The maximum figure of merit ZT values of the NCS, LCS, and HCS samples were 0.46, 0.48, and 0.57, respectively. Therefore, applying a high-density electric current in the sintering process may be an effective way to obtain Bi_1.2Sb_4.8Te₉ thermoelectric material with high ZT value.     

Features of the charge-transport mechanism in layered Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> single crystals doped with chlorine and terbium

The temperature dependences (T = 5−300 K) of the resistivity in the plane of layers and in the direction perpendicular to the layers, as well as the Hall effect and the magnetoresistance (H < 80 kOe, T = 0.5−4.2 K) in Bi₂Te₃ single crystals doped with chlorine and terbium, are investigated. It is shown that the doping of Bi₂Te₃ with terbium atoms results in p-type conductivity and in increasing hole concentration. The doping of Bi₂Te₃ with chlorine atoms modifies also the character of its conductivity instead of changing only the type from p to n. In the temperature dependence of the resistivity in the direction perpendicular to layers, a portion arises with the activation conductivity caused by the hopping between localized states. The charge-transport mechanism in Bi₂Te₃ single crystals doped with chlorine is proposed.     

Power Factor Anisotropy of <Emphasis Type="Italic">p</Emphasis>-Type and <Emphasis Type="Italic">n</Emphasis>-Type Conductive Thermoelectric Bi-Sb-Te Thin Films

The best films for thermoelectric applications near room temperature are based on the compounds Bi₂Te₃, Sb₂Te₃, and Bi₂Se₃, which as single crystals have distinct anisotropy in their electrical conductivity σ regarding the trigonal c-axis, whereas the Seebeck coefficient S is nearly isotropic. For p- and n-type alloys, P _⊥c > P _||c, and the power factors P _⊥c of single crystals are always higher compared with polycrystalline films, where the power factor is defined as P = S ² σ, ⊥c and ||c are the direction perpendicular and parallel to the c-axis, respectively. For the first time in sputter-deposited p-type (Bi_0.15Sb_0.85)₂Te₃ and n-type Bi₂(Te_0.9Se_0.1)₃ thin films, the anisotropy of the electrical conductivity has been measured directly as it depends on the angle φ between the electrical current and the preferential orientation of the polycrystals (texture) using a standard four-probe method. The graphs of σ(φ) show the expected behavior, which can be described by a weighted mixture of σ _⊥c and σ _||c contributions. Because (σ _⊥c/σ _||c) _p  < (σ _⊥c/σ _||c) _n , the n-type films have stronger anisotropy than the p-type films. For this reason, the angular weighted contributions of P _||c lead to a larger drop in the power factor of polycrystalline n-type films compared with p-type films.     

Effect of Deformation Temperature on Texture and Thermoelectric Properties of Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> Prepared by Hot-Press Deformation

The effects of deformation temperature on texture and thermoelectric properties of p-type Bi_0.5Sb_1.5Te₃ sintered materials were investigated. The sintered materials were prepared by mechanical alloying and hot-press sintering. The hot-press deformation was performed at 723 K and 823 K by applying mechanical pressure in a graphite die. Then, the materials were extruded in the direction opposite to the direction of applied pressure. X-ray diffraction and electron backscattered diffraction patterns showed that the hexagonal c-plane tended to align along the extruded direction when the samples were deformed at high temperatures. The thermoelectric power factor was increased by high-temperature hot-press deformation because of the low electrical resistivity that originated from the c-plane orientation.     

Effect of Vacancy Distribution on the Thermal Conductivity of Ga<Subscript>2</Subscript>Te<Subscript>3</Subscript> and Ga<Subscript>2</Subscript>Se<Subscript>3</Subscript>

Our group has focused attention on Ga₂Te₃ as a natural nanostructured thermoelectric material. Ga₂Te₃ has basically a zincblende structure, but one-third of the Ga sites are structural vacancies due to the valence mismatch between Ga and Te. It has been confirmed that (1) vacancies in Ga₂Te₃ exist as two-dimensional (2D) vacancy planes, and (2) Ga₂Te₃ exhibits an unexpectedly low thermal conductivity (κ), most likely due to highly effective phonon scattering by the 2D vacancy planes. However, the effect of the size and periodicity of the 2D vacancy planes on κ has been unclear. In addition, it has also been unclear whether only the 2D vacancy planes reduce κ or if point-type vacancies can also reduce κ. In the present study, we tried to prepare Ga₂Te₃ and Ga₂Se₃ with various vacancy distributions by controlling annealing conditions. The atomic structures of the samples were characterized by means of transmission electron microscopy, and κ was evaluated from the thermal diffusivity measured by the laser flash method. The effects of vacancy distributions on κ of Ga₂Te₃ and Ga₂Se₃ are discussed.     

Solid-State Synthesis of Te-Doped Mg<Subscript>2</Subscript>Si

Te-doped Mg₂Si (Mg₂Si:Te _m , m = 0, 0.01, 0.02, 0.03, 0.05) alloys were synthesized by a solid-state reaction and mechanical alloying. The electronic transport properties (Hall coefficient, carrier concentration, and mobility) and thermoelectric properties (Seebeck coefficient, electrical conductivity, thermal conductivity, and figure of merit) were examined. Mg₂Si was synthesized successfully by a solid-state reaction at 673 K for 6 h, and Te-doped Mg₂Si powders were obtained by mechanical alloying for 24 h. The alloys were fully consolidated by hot-pressing at 1073 K for 1 h. All the Mg₂Si:Te _m samples showed n-type conduction, indicating that the electrical conduction is due mainly to electrons. The electrical conductivity increased and the absolute value of the Seebeck coefficient decreased with increasing Te content, because Te doping increased the electron concentration considerably from 10¹⁶ cm⁻³ to 10¹⁸ cm⁻³. The thermal conductivity did not change significantly on Te doping, due to the much larger contribution of lattice thermal conductivity over the electronic thermal conductivity. Thermal conduction in Te-doped Mg₂Si was due primarily to lattice vibrations (phonons). The thermoelectric figure of merit of intrinsic Mg₂Si was improved by Te doping.     

Thermoelectric Properties of Ag-Doped n-Type (Bi2?xAgxTe3)0.96?(Bi2Se3)0.04 Pseudobinary Alloys

n-Type thermoelectric powders of (Bi_2−x Ag _x Te₃)_0.96−(Bi₂Se₃)_0.04 (0 ≤ x ≤ 0.05) have been synthesized by mechanical alloying and then consolidated by spark plasma sintering. The analysis results show that the grain size of pure Bi, Te, Ag, and Se powders is decreased to about 1 μm to 0.5 μm after they are mechanically alloyed for 2 h. The power factor of bulk material increases with increasing Ag-doping content, while the trend for the lattice thermal conductivity is the opposite. Bulk (Bi_0.99Ag_0.04)₂(Te_0.96Se_0.04)₃ after milling for 12 h exhibits a higher power factor, lower thermal conductivity, and thus a higher ZT of 0.74 at 373 K.