一种带有混合平均式分布采样电路的低功耗CMOS全折叠型模数转换器

This paper describes an 8-bit 125 MHz low-power CMOS fully-folding analog-to-digital converter （ADC） A novel mixed-averaging distributed T/H circuit is proposed to improve the accuracy. Folding circuits are not only used in the fine converter but also in the coarse one and in the bit synchronization block to reduce the number of comparators for low power. This ADC is implemented in 0.5μm CMOS technology and occupies a die area of 2 × 1.5 mm^2. The measured differential nonlinearity and integral nonlinearity are 0.6 LSB/-0.8 LSB and 0.9 LSB/-1.2 LSB, respectively. The ADC exhibits 44.3 dB of signal-to-noise plus distortion ratio and 53.5 dB of spurious-free dynamic range for 1 MHz input sine-wave. The power dissipation is 138 mW at a sampling rate of 125 MHz at a 5 V supply.     

应用于CMOS图像传感器中带有失调电压消除功能的电容比值非相关十位循环式模数转换器

A 10-bit ratio-independent switch-capacitor（SC） cyclic analog-to-digital converter（ADC） with offset cancelingforaCMOSimagesensorispresented.TheproposedADCcompletesanN-bitconversionin1.5N clock cycles with one operational amplifier. Combining ratio-independent and polarity swapping techniques, the conversioncharacteristicoftheproposedcyclicADCisinherentlyinsensitivebothtocapacitorratioandtoamplifieroffset voltage. Therefore, the circuit can be realized in a small die area and it is suitable to serve as the column-parallel ADC in CMOS image sensors. A prototype ADC is fabricated in 0.18- m one-poly four-metal CMOS technology.The measured results indicate that the ADC has a signal-to-noise and distortion ratio（SNDR） of 53.6 dB and a DNL of C0：12/0：14 LSB at a conversion rate of 600 kS/s. The standard deviation of the offset variation of the ADC is reduced from 2.5 LSB to 0.5 LSB. Its power dissipation is 250 W with a 1.8 V supply, and its area is0.030.8 mm2.     

A novel monolithic ultraviolet image sensor based on a standard CMOS process

We present a monolithic ultraviolet(UV) image sensor based on a standard CMOS process.A compact UV sensitive device structure is designed as a pixel for the image sensor.This UV image sensor consists of a CMOS pixel array,high-voltage switches,a readout circuit and a digital control circuit.A 16×16 image sensor prototype chip is implemented in a 0.18μm standard CMOS logic process.The pixel and image sensor were measured. Experimental results demonstrate that the image sensor has a high sensitivity of 0.072 V/(mJ/cm~2) and can capture a UV image.It is suitable for large-scale monolithic bio-medical and space applications.     

一种采用PVT不敏感电荷传输电路的27mW 10位125MSPS 电荷域流水线模数转换器

A low power 10-bit 125-MSPS charge-domain(CD) pipelined analog-to-digital converter(ADC) based on MOS bucket-brigade devices(BBDs) is presented.A PVT insensitive boosted charge transfer(BCT) that is able to reject the charge error induced by PVT variations is proposed.With the proposed BCT,the common mode charge control circuit can be eliminated in the CD pipelined ADC and the system complexity is reduced remarkably.The prototype ADC based on the proposed BCT is realized in a 0.18μm CMOS process,with power consumption of only 27 mW at 1.8-V supply and active die area of 1.04 mm~2.The prototype ADC achieves a spurious free dynamic range(SFDR) of 67.7 dB,a signal-to-noise ratio(SNDR) of 57.3 dB,and an effective number of bits(ENOB) of 9.0 for a 3.79 MHz input at full sampling rate.The measured differential nonlinearity(DNL) and integral nonlinearity (INL) are +0.5/-0.3 LSB and +0.7/-0.55 LSB,respectively.     

采用电压复位技术的像素级模数转换器

This paper presents a 50 Hz 15-bit analog-to-digital converter(ADC) for pixel-level implementation in CMOS image sensors.The ADC is based on charge packets counting and adopts a voltage reset technique to inject charge packets.The core circuit for charge/pulse conversion is specially optimized for low power,low noise and small area.An experimental chip with ten pixel-level ADCs has been fabricated and tested for verification.The measurement result shows a standard deviation of 1.8 LSB for full-scale output.The ADC has an area of 4545 m2 and consumes less than 2 W in a standard 1P-6M 0.18 m CMOS process.     

A readout integrated circuit based on DBI-CTIA and cyclic ADC for MEMS-arraybased focal plane

A readout integrated circuit (ROIC) for a MEMS (microelectromechanical system)-array-based focal plane (MAFP) intended for imaging applications is presented. The ROIC incorporates current sources for diode detectors, scanners, timing sequence controllers, differential buffered injection-capacitive trans-impedance amplifier (DBI-CTIA) and 10-bit cyclic ADCs, and is integrated with MAFP using 3-D integration technology. A small-signal equivalent model is built to include thermal detectors into circuit simulations. The biasing current is optimized in terms of signal-to-noise ratio and power consumption. Layout design is tailored to fulfill the requirements of 3-D integration and to adapt to the size of MAFP elements, with not all but only the 2 bottom metal layers to complete nearly all the interconnections in DBI-CTIA and ADC in a 40 μm wide column. Experimental chips are designed and fabricated in a 0.35 μm CMOS mixed signal process, and verified in a code density test of which the results indicate a (0.29/-0.31) LSB differential nonlinearity (DNL) and a (0.61/-0.45) LSB integral nonlinearity (INL). Spectrum analysis shows that the effective number of bits (ENOB) is 9.09. The ROIC consumes 248 mW of power at most if not to cut off quiescent current paths when not needed.     

一种基于时域比较器高SFDR的6-bit 20-MS/s 逐次逼近模数转换器

This paper presents a 6-bit 20-MS/s high spurious-free dynamic range(SFDR) and low power successive approximation register analog to digital converter(SAR ADC) for the radio-frequency(RF) transceiver frontend, especially for wireless sensor network(WSN) applications.This ADC adopts the modified common-centroid symmetry layout and the successive approximation register reset circuit to improve the linearity and dynamic range. Prototyped in a 0.18-μm 1P6M CMOS technology,the ADC performs a peak SFDR of 55.32 dB and effective number of bits(ENOB) of 5.1 bit for 10 MS/s.At the sample rate of 20 MS/s and the Nyquist input frequency,the 47.39-dB SFDR and 4.6-ENOB are achieved.The differential nonlinearity(DNL) is less than 0.83 LSB and the integral nonlinearity(INL) is less than 0.82 LSB.The experimental results indicate that this SAR ADC consumes a total of 522μW power and occupies 0.98 mm~2.     

A 14-bit 40-MHz analog front end for CCD application

A 14-bit, 40-MHz analog front end (AFE) for CCD scanners is analyzed and designed. The proposed system incorporates a digitally controlled wideband variable gain amplifier (VGA) with nearly 42 dB gain range, a correlated double sampler (CDS) with programmable gain functionality, a 14-bit analog-to-digital converter and a programmable timing core. To achieve the maximum dynamic range, the VGA proposed here can linearly amplify the input signal in a gain range from -1.08 to 41.06 dB in 6.02 dB step with a constant bandwidth. A novel CDS takes image information out of noise, and further amplifies the signal accurately in a gain range from 0 to 18 dB in 0.035 dB step. A 14-bit ADC is adopted to quantify the analog signal with optimization in power and linearity. An internal timing core can provide flexible timing for CCD arrays, CDS and ADC. The proposed AFE was fabricated in SMIC 0.18 μm CMOS process. The whole circuit occupied an active area of 2.8×4.8 mm² and consumed 360 mW. When the frequency of input signal is 6.069 MHz, and the sampling frequency is 40 MHz, the signal to noise and distortion (SNDR) is 70.3 dB, the effective number of bits is 11.39 bit.     

一种8-b 180KSPS的带有新颖的时域比较器且有效位数7.97的差分逐次逼近模数转换器

This paper presents a differential successive approximation register analog-to-digital converter (SAR ADC) with a novel time-domain comparator design for wireless sensor networks. The prototype chip has been implemented in the UMC 0.18-μ m 1P6M CMOS process. The proposed ADC achieves a peak ENOB of 7.98 at an input frequency of 39.7 kHz and sampling rate of 180 kHz. With the Nyquist input frequency, 68.49-dB SFDR, 7.97-ENOB is achieved. A simple quadrate layout is adopted to ease the routing complexity of the common-centroid symmetry layout. The ADC maintains a maximum differential nonlinearity of less than 0.08 LSB and integral nonlinearity less than 0.34 LSB by this type of layout.     

A power-efficient 12-bit analog-to-digital converter with a novel constant-resistance CMOS input sampling switch

Apower-efficient 12-bit40-MS/spipelineanalog-to-digitalconverter（ADC）implementedina0.13 μm CMOS technology is presented. A novel CMOS bootstrapping switch, which offers a constant on-resistance over the entire input signal range, is used at the sample-and-hold front-end to enhance the dynamic performance of the pipelined ADC. By implementing with 2.5-bit-per-stage and a simplified amplifier sharing architecture between two successive pipeline stages, a very competitive power consumption and small die area can be achieved. Meanwhile, the substrate-biasing-effect attenuated T-type switches are introduced to reduce the crosstalk between the two op- amp sharing successive stages. Moreover, a two-stage gain boosted recycling folded cascode （RFC） amplifier with hybrid frequency compensation is developed to further reduce the power consumption and maintain the ADC＇s performance simultaneously. The measured results imply that the ADC achieves a spurious-free dynamic range （SFDR） of 75.7 dB and a signal-to-noise-plus-distortion ratio （SNDR） of 62.74 dB with a 4.3 MHz input signal; the SNDR maintains over 58.25 dB for input signals up to 19.3MHz. The measured differential nonlinearity （DNL） and integral nonlinearity （INL） are -0.43 to ＋0.48 LSB and -1.62 to ＋ 1.89 LSB respectively. The prototype ADC consumes 28.4 mW under a 1.2-V nominal power supply and 40 MHz sampling rate, transferring to a figure- of-merit （FOM） of 0.63 pJ per conversion-step.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Call for Papers

正Communications—VLSI Researches and industries of telecommunications have been growing rapidly in the last 20 years and will keep their high growing pace in the next decade.The involved researches and developments cover mobile communications,highway and last-mile broadband communication,domain specific communications,and emerging D2D M2M communications.Radio communication steps into its