Thermoelectric Properties of the Narrow-Gap Intermetallic Compound Ga<Subscript>2</Subscript>Ru: Effect of Re Substitution for Ru Atoms

In this paper, the effect of hole doping on the thermoelectric properties of the binary narrow-gap semiconducting intermetallic compound Ga₂Ru in the temperature range from 373 K to 973 K was investigated. We synthesized sintered pellets by spark plasma sintering (SPS) after arc-melting and succeeded in preparing crack-free samples. The maximum dimensionless figure of merit ZT _max was 0.50 at 773 K for the sintered Ga₂Ru alloy. The temperature dependence of the electrical resistivity and its magnitude at 373 K dramatically changed from negative (~11,000 μΩcm) to positive (~200 μΩcm) upon hole doping by the substitution of Re for Ru atoms. Also, the Seebeck coefficient at 373 K changed from 300 μV/K to 75 μV/K. These changes were identified by the increase in carrier concentrations observed by Hall- effect measurements. In particular, large power factors (2.0 mW/m K² to 3.0 mW/m K²) were obtained over a wide temperature range from 373 K to 973 K upon Re substitution. The lattice thermal conductivity beneficially decreased with increasing Re concentration as a result of an alloying effect.     

Thermoelectric Properties of In<Subscript>0.3</Subscript>Ga<Subscript>0.7</Subscript>N Alloys

We report on the experimental investigation of the potential of InGaN alloys as thermoelectric (TE) materials. We have grown undoped and Si-doped In_0.3Ga_0.7N alloys by metalorganic chemical vapor deposition and measured the Seebeck coefficient and electrical conductivity of the grown films with the aim of maximizing the power factor (P). It was found that P decreases as electron concentration (n) increases. The maximum value for P was found to be 7.3 × 10⁻⁴ W/m K² at 750 K in an undoped sample with corresponding values of Seebeck coefficient and electrical conductivity of 280 μV/K and 93␣(Ω cm)⁻¹, respectively. Further enhancement in P is expected by improving the InGaN material quality and conductivity control by reducing background electron concentration.     

Thermoelectric Properties of NdGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> Prepared by CS<Subscript>2</Subscript> Sulfurization

Ternary rare-earth sulfides NdGd_1+x S₃, where 0 ≤ x ≤ 0.08, were prepared by sulfurizing Ln₂O₃ (Ln = Nd, Gd) with CS₂ gas, followed by reaction sintering. The sintered samples have full density and homogeneous compositions. The Seebeck coefficient, electrical resistivity, and thermal conductivity were measured over the temperature range of 300 K to 950 K. All the sintered samples exhibit a negative Seebeck coefficient. The magnitude of the Seebeck coefficient and the electrical resistivity decrease systematically with increasing Gd content. The thermal conductivity of all the sintered samples is less than 1.9 W K⁻¹ m⁻¹. The highest figure of merit ZT of 0.51 was found in NdGd_1.02S₃ at 950 K.     

Impedance Spectroscopy of Dielectric BaTi<Subscript>5</Subscript>O<Subscript>11</Subscript> Film Prepared by Laser Chemical Vapor Deposition Method

BaTi₅O₁₁ film was prepared on Pt/Ti/SiO₂/Si substrate by the laser chemical vapor deposition method. A single-phase BaTi₅O₁₁ film with ([`3] 22)/([`2] 23) (\overline{3} 22)/(\overline{2} 23) preferred orientation and columnar cross-section was obtained at high deposition rate (154.8 μm h⁻¹). The dielectric constant (ε _r) of the BaTi₅O₁₁ film was 21, measured at 300 K and 1 MHz. The electrical properties of the BaTi₅O₁₁ film were investigated by ac impedance spectroscopy from 300 K to 1073 K at 10² Hz to 10⁷ Hz. Plots of the real and imaginary parts of the impedance (Z′ and Z″) and electrical modulus (M′ and M″) in the above frequency and temperature range suggested the presence of two relaxation regimes, which were attributed to grain and grain boundary responses. The ac conductivity plots as a function of frequency showed three types of conduction process at elevated temperature. The frequency-independent plateau at low frequency was due to dc conductivity. The mid-frequency conductivity was due to grain boundaries, while the high-frequency conductivity was due to grains.     

Thermoelectric Properties of Layer-Antiferromagnet CuCrS<Subscript>2</Subscript>

We have performed a detailed study of the electrical and thermal conductivities and thermoelectric power behavior of an antiferromagnetic-layer compound of chromium, CuCrS₂, from 15 K to 300 K. Unlike previous studies, we find noninsulating properties and sensitive dependence on the preparation method, the microstructure, and the flaky texture formed in polycrystalline samples after extended sintering at high temperatures. Flakes are found to be metallic, with strong localization effects in the conductivity on cooling to low temperatures. The antiferromagnetic transition temperature T _N (=40 K) remains essentially unaffected. The Seebeck coefficient is found to be in the range of 150 μV/K to 450 μV/K, which is exceptionally large, and becomes temperature independent at high temperatures, even for specimens with low resistivity values of 5 mΩ cm to 200 mΩ cm. We find the thermal conductivity κ to be low, viz. 5 mW/K cm to 30 mW/K cm. This can be attributed mostly to the dominance of lattice conduction over electronic conduction. The value of κ is further reduced by disorder in Cu occupancy in the quenched phase. We also observe an unusually strong dip in κ at T _N, which is probably due to strong magnetocrystalline coupling in these compounds. Finally we discuss the properties of CuCrS₂ as a heavily doped Kondo-like insulator in its paramagnetic phase. The combination of the electronic properties observed in CuCrS₂ makes it a potential candidate for various thermoelectric applications.     

Thermoelectric Properties of Co<Subscript>4</Subscript>Sb<Subscript>12</Subscript> Skutterudite Materials with Partial In Filling and Excess In Additions

The properties of Co₄Sb₁₂ with various In additions were studied. X-ray diffraction revealed the presence of the pure δ-phase of In_0.16Co₄Sb₁₂, whereas impurity phases (γ-CoSb₂ and InSb) appeared for x = 0.25, 0.40, 0.80, and 1.20. The homogeneity and morphology of the samples were observed by Seebeck microprobe and scanning electron microscopy, respectively. All the quenched ingots from which the studied samples were cut were inhomogeneous in the axial direction. The temperature dependence of the Seebeck coefficient (S), electrical conductivity (σ), and thermal conductivity (κ) was measured from room temperature up to 673 K. The Seebeck coefficient of all In-added Co₄Sb₁₂ materials was negative. When the filler concentration increases, the Seebeck coefficient decreases. The samples with In additions above the filling limit (x = 0.22) show an even lower Seebeck coefficient due to the formation of secondary phases: InSb and CoSb₂. The temperature variation of the electrical conductivity is semiconductor-like. The thermal conductivity of all the samples decreases with temperature. The central region of the In_0.4Co₄Sb₁₂ ingot shows the lowest thermal conductivity, probably due to the combined effect of (a) rattling due to maximum filling and (b) the presence of a small amount of fine-dispersed secondary phases at the grain boundaries. Thus, regardless of the non-single-phase morphology, a promising ZT (S ² σT/κ) value of 0.96 at 673 K has been obtained with an In addition above the filling limit.     

Preparation and Thermoelectric Properties of LaGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript> and SmGd<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>S<Subscript>3</Subscript>

Thermoelectric materials are attractive since they can recover waste heat directly in the form of electricity. In this study, the thermoelectric properties of ternary rare-earth sulfides LaGd_1+x S₃ (x = 0.00 to 0.03) and SmGd_1+x S₃ (x = 0.00 to 0.06) were investigated over the temperature range of 300 K to 953 K. These sulfides were prepared by CS₂ sulfurization, and samples were consolidated by pressure-assisted sintering to obtain dense compacts. The sintered compacts of LaGd_1+x S₃ were n-type metal-like conductors with a thermal conductivity of less than 1.7 W K⁻¹ m⁻¹. Their thermoelectric figure of merit ZT was improved by tuning the chemical composition (self-doping). The optimized ZT value of 0.4 was obtained in LaGd_1.02S₃ at 953 K. The sintered compacts of SmGd_1+x S₃ were n-type hopping conductors with a thermal conductivity of less than 0.8 W K⁻¹ m⁻¹. Their ZT value increased significantly with temperature. In SmGd_1+x S₃, the ZT value of 0.3 was attained at 953 K.     

Preparation and Thermoelectric Properties of La-Doped SrTiO<Subscript>3</Subscript> Ceramics

Single-phase polycrystalline La _x Sr_1−x TiO₃ (x = 0, 0.04, 0.06, 0.08, and 0.12) ceramics were prepared by the conventional solid-state reaction method using high-activity hydroxides as the raw materials. The electrical conductivity of all the samples increased with increasing x value and decreased with measurement temperature, while the thermal conductivity decreased with increasing x value and measurement temperature. The La_0.12Sr_0.88TiO₃ sample showed the lowest thermal conductivity of 2.45 W m⁻¹ K⁻¹ at 873 K and the largest ZT of 0.28 at 773 K. The present work revealed that hydroxides with high activity as raw materials are beneficial to improve the thermoelectric properties, especially to decrease the thermal conductivity.     

Thermoelectric Properties of Ag-doped Mg<Subscript>2</Subscript>Ge Thin Films Prepared by Magnetron Sputtering

Silver doped p-type Mg₂Ge thin films were grown in situ at 773 K using magnetron co-sputtering from individual high-purity Mg and Ge targets. A sacrificial base layer of silver of various thicknesses from 4 nm to 20 nm was initially deposited onto the substrate to supply Ag atoms, which entered the growing Mg₂Ge films by thermal diffusion. The addition of silver during film growth led to increased grain size and surface microroughness. The carrier concentration increased from 1.9 × 10¹⁸ cm⁻³ for undoped films to 8.8 × 10¹⁸ cm⁻³ for the most heavily doped films, but it did not reach saturation. Measurements in the temperature range of T = 200–650 K showed a positive Seebeck coefficient for all the films, with maximum values at temperatures between 400 K and 500 K. The highest Seebeck coefficient of the undoped film was 400 μV K⁻¹, while it was 280 μV K⁻¹ for the most heavily doped film at ∼400 K. The electrical conductivity increased with silver doping by a factor of approximately 10. The temperature effects on power factors for the undoped and lightly doped films were very limited, while the effects for the heavily doped films were substantial. The power factor of the heavily doped films reached a non-optimum value of ∼10⁻⁵ W cm⁻¹ K⁻² at 700 K.     

Solid-State Synthesis of Te-Doped Mg<Subscript>2</Subscript>Si

Te-doped Mg₂Si (Mg₂Si:Te _m , m = 0, 0.01, 0.02, 0.03, 0.05) alloys were synthesized by a solid-state reaction and mechanical alloying. The electronic transport properties (Hall coefficient, carrier concentration, and mobility) and thermoelectric properties (Seebeck coefficient, electrical conductivity, thermal conductivity, and figure of merit) were examined. Mg₂Si was synthesized successfully by a solid-state reaction at 673 K for 6 h, and Te-doped Mg₂Si powders were obtained by mechanical alloying for 24 h. The alloys were fully consolidated by hot-pressing at 1073 K for 1 h. All the Mg₂Si:Te _m samples showed n-type conduction, indicating that the electrical conduction is due mainly to electrons. The electrical conductivity increased and the absolute value of the Seebeck coefficient decreased with increasing Te content, because Te doping increased the electron concentration considerably from 10¹⁶ cm⁻³ to 10¹⁸ cm⁻³. The thermal conductivity did not change significantly on Te doping, due to the much larger contribution of lattice thermal conductivity over the electronic thermal conductivity. Thermal conduction in Te-doped Mg₂Si was due primarily to lattice vibrations (phonons). The thermoelectric figure of merit of intrinsic Mg₂Si was improved by Te doping.     

Microstructure and Thermoelectric Properties of AgSbO<Subscript>3</Subscript> Ceramics Prepared by Ion-Exchange Powder Synthesis and Normal Sintering

Silver antimonate (AgSbO₃) is a potential high-temperature thermoelectric oxide with a low thermal conductivity, but it is difficult to fabricate dense bulk material with high phase purity. Well-dispersed AgSbO₃ nanopowder with an average diameter of 50 nm was synthesized by an ion-exchange process in this study, the sintering density of which was apparently enhanced. Nearly single-phase AgSbO₃ ceramic samples with a relative density close to 90% were obtained when sintered at a relatively low temperature (1273 K). The electrical conductivity of AgSbO₃ increased greatly with increasing sintering temperature, probably because of defects originating from the compositional deviation caused by sintering, in addition to increased density. This study also confirmed that AgSbO₃ had a low thermal conductivity, from 1.1 W m⁻¹ K⁻¹ at room temperature to 0.8 W m⁻¹ K⁻¹ at 673 K.     

Thermoelectric Properties of the Clathrate I Ba<Subscript>8</Subscript>Ge<Subscript>43</Subscript>□<Subscript>3</Subscript>

The clathrate I Ba₈Ge₄₃□₃ [space group Ia[`3]d Ia\bar{3}d , no. 230, a = 21.307(1) ?] has been synthesized as a single phase and characterized by x-ray powder diffraction and metallographic analysis. Electrical and thermal transport measurements have been performed in the temperature range of 5 K to 673 K. Ba₈Ge₄₃□₃ displays the electrical resistivity of a poor metal at low temperatures, with semiconducting-like behavior appearing above 300 K.     

Thermoelectric Properties of Ca-Filled CoSb<Subscript>3</Subscript>-Based Skutterudites Synthesized by Mechanical Alloying

Ca _z Co_4−x (Fe/Mn) _x Sb₁₂ skutterudites were prepared by mechanical alloying and hot pressing. The phases of mechanically alloyed powders were identified as γ-CoSb₂ and Sb, but they were transformed to δ-CoSb₃ by annealing at 873 K for 100 h. All specimens had a positive Hall coefficient and Seebeck coefficient, indicating p-type conduction by holes as majority carriers. For the binary CoSb₃, the electrical conductivity behaved like a nondegenerate semiconductor, but Ca-filled and Fe/Mn-doped CoSb₃ showed a temperature dependence of a degenerate semiconductor. While the Seebeck coefficient of intrinsic CoSb₃ increased with temperature and reached a maximum at 623 K, the Seebeck coefficient increased with increasing temperature for the Ca-filled and Fe/Mn-doped specimens. Relatively low thermal conductivity was obtained because fine particles prepared by mechanical alloying lead to phonon scattering. The thermal conductivity was reduced by Ca filling and Fe/Mn doping. The electronic thermal conductivity was increased by Fe/Mn doping, but the lattice thermal conductivity was decreased by Ca filling. Reasonable thermoelectric figure-of-merit values were obtained for Ca-filled Co-rich p-type skutterudites.     

Electrodeposition and Thermoelectric Characteristics of Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> and Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> Films for Thermopile Sensor Applications

A thermopile sensor was processed on a glass substrate by electrodeposition of n-type bismuth telluride (Bi-Te) and p-type antimony telluride (Sb-Te) films. The n-type Bi-Te film electrodeposited at −50 mV in a 50 mM electrolyte with a Bi/(Bi + Te) mole ratio of 0.5 exhibited a Seebeck coefficient of −51.6 μV/K and a power factor of 7.1 × 10⁻⁴ W/K² · m. The p-type Sb-Te film electroplated at 20 mV in a 70 mM solution with an Sb/(Sb + Te) mole ratio of 0.9 exhibited a Seebeck coefficient of 52.1 μV/K and a power factor of 1.7 × 10⁻⁴ W/K² · m. A thermopile sensor composed of 196 pairs of the p-type Sb-Te and the n-type Bi-Te thin-film legs exhibited sensitivity of 7.3 mV/K.     

Increase in the Thermoelectric Efficiency of the Disordered Phase of Layered Antiferromagnetic CuCrS<Subscript>2</Subscript>

The thermoelectric figure of merit (ZT) of the layered antiferromagnetic compound CuCrS₂ is further improved with increase in the Cr-vacancy disorder on sintering above 900°C. X-ray photoelectron spectroscopy and x-ray diffraction refinement results for different samples show that the chromium atoms are transferred from the filled layers to the vacant sites between the layers. This atomic disorder increases the electrical conductivity (σ) due to self-doping of the charge carriers and reduces thermal conductivity (κ) due to increase in phonon scattering. The Seebeck coefficient (S) is p-type and remains nearly temperature independent with values between 150 μV/K and 450 μV/K due to electronic doping in different samples.     

Preparation and Thermoelectric Characterization of SiC-B<Subscript>4</Subscript>C Composites

SiC-B₄C composites with various values of SiC-to-B₄C ratio and grain size were fabricated by pressureless sintering. This paper presents the results of current investigations of this composite material. This includes the parameters of manufacture (shrinkage, density, and open porosity), thermoelectric properties (electrical and thermal conductivity, and thermopower), and material characterization (x-ray diffraction, scanning electron microscopy, oxidation resistance, and thermal expansion). The results indicate high potential of this composite as an alternative material for thermoelectric applications at high temperatures. The Seebeck coefficient of the composite was higher than that of the single-component materials B₄C and SiC and reached 400 μV/K at 500°C.     

Improvement of Thermoelectric Power Factor of Hydrothermally Prepared Bi<Subscript>0.5</Subscript>Sb<Subscript>1.5</Subscript>Te<Subscript>3</Subscript> Compared with its Solvothermally Prepared Counterpart

We report on the successful hydrothermal synthesis of Bi_0.5Sb_1.5Te₃, using water as the solvent. The products of the hydrothermally prepared Bi_0.5 Sb_1.5Te₃ were hexagonal platelets with edges of 200–1500 nm and thicknesses of 30–50 nm. Both the Seebeck coefficient and electrical conductivity of the hydrothermally prepared Bi_0.5Sb_1.5Te₃ were larger than those of the solvothermally prepared counterpart. Hall measurements of Bi_0.5Sb_1.5Te₃ at room temperature indicated that the charge carrier was p-type, with a carrier concentration of 9.47 × 10¹⁸ cm⁻³ and 1.42 × 10¹⁹ cm⁻³ for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively. The thermoelectric power factor at 290 K was 10.4 μW/cm K² and 2.9 μW/cm K² for the hydrothermally prepared Bi_0.5Sb_1.5Te₃ and solvothermally prepared sample, respectively.     

Thermoelectric Properties of Sb-Doped Mg<Subscript>2</Subscript>Si<Subscript>0.3</Subscript>Sn<Subscript>0.7</Subscript>

Mg₂(Si_0.3Sn_0.7)_1−y Sb _y (0 ≤ y ≤ 0.04) solid solutions were prepared by a two-step solid-state reaction method combined with the spark plasma sintering technique. Investigations indicate that the Sb doping amount has a significant impact on the thermoelectric properties of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y compounds. As the Sb fraction y increases, the electron concentration and electrical conductivity of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y first increase and then decrease, and both reach their highest value at y = 0.025. The sample with y = 0.025, possessing the highest electrical conductivity and one of the higher Seebeck coefficient values among all the samples, has the highest power factor, being 3.45 mW m⁻¹ K⁻² to 3.69 mW m⁻¹ K⁻² in the temperature range of 300 K to 660 K. Meanwhile, Sb doping can significantly reduce the lattice thermal conductivity (κ _ph) of Mg₂(Si_0.3Sn_0.7)_1−y Sb _y due to increased point defect scattering, and κ _ph for Sb-doped samples is 10% to 20% lower than that of the nondoped sample for 300 K < T < 400 K. Mg₂(Si_0.3Sn_0.7)_0.975Sb_0.025 possesses the highest power factor and one of the lower κ _ph values among all the samples, and reaches the highest ZT value: 1.0 at 640 K.     

Effect of Rapid Thermal Annealing on Sputtered CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> Thin Films

Calcium copper titanium oxide (CaCu₃Ti₄O₁₂, abbreviated to CCTO) films were deposited on Pt/Ti/SiO₂/Si substrates at room temperature (RT) by radiofrequency magnetron sputtering. As-deposited CCTO films were treated by rapid thermal annealing (RTA) at various temperatures and in various atmospheres. X-ray diffraction patterns and scanning electron microscope (SEM) images demonstrated that the crystalline structures and surface morphologies of CCTO thin films were sensitive to the annealing temperature and ambient atmosphere. Polycrystalline CCTO films could be obtained when the annealing temperature was 700°C in air, and the grain size increased signifi- cantly with annealing in O₂. The 0.8-μm CCTO thin film that was deposited at RT for 2 h and then annealed at 700°C in O₂ exhibited a high dielectric constant (ε′) of 410, a dielectric loss (tan δ) of 0.17 (at 10 kHz), and a leakage current density (J) of 1.28 × 10⁻⁵ A/cm² (at 25 kV/cm).     

Thermoelectric Properties of Zr<Subscript>3</Subscript>Mn<Subscript>4</Subscript>Si<Subscript>6</Subscript> and TiMnSi<Subscript>2</Subscript>

The Seebeck coefficient, electrical resistivity, and thermal conductivity of Zr₃Mn₄Si₆ and TiMnSi₂ were studied. The crystal lattices of these compounds contain relatively large open spaces, and, therefore, they have fairly low thermal conductivities (8.26 Wm⁻¹ K⁻¹ and 6.63 Wm⁻¹ K⁻¹, respectively) at room temperature. Their dimensionless figures of merit ZT were found to be 1.92 × 10⁻³ (at 1200 K) and 2.76 × 10⁻³ (at 900 K), respectively. The good electrical conductivities and low Seebeck coefficients might possibly be due to the fact that the distance between silicon atoms in these compounds is shorter than that in pure semiconductive silicon.