首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
为了能有效解决柔性基底体声波谐振器热稳定性不足及功率容量不足等问题,该文提出了一种新型的基于柔性基底的薄膜体声波谐振器。该谐振器的硅衬底上开设有一定数量的垂直上凸型结构,该结构既能有效抑制寄生模量,又能减小器件最高稳态温度和最大热应力。通过有限元分析软件Comsol Multiphics对谐振器进行仿真,结果表明,器件每增加一个上凸型结构,其最高稳态温度下降了4 ℃,最大热应力下降了1×104 GPa。与以往的柔性基底薄膜体声波谐振器相比,它具有更好的热传导能力和热应力稳定性。  相似文献   

2.
对90 nm PDSOI MOSFET的热阻进行了提取与研究。以H型栅MOSFET为研究对象,将源体二极管作为温度敏感器,通过测量源体结电流与器件温度的关系以及源体结电流与器件功率的关系,获得MOS器件功率与器件温度的关系,从而获取MOS器件热阻值。实验结果表明,该工艺下PMOS器件的热阻比NMOS器件大,其原因是PMOS体区掺杂浓度比NMOS高,而掺杂浓度越高,导热性越差,热阻就越大;H型栅器件的归一化热阻随沟道宽度的增加而增大,其原因是随着沟道宽度的增加,体引出区域对器件导热的贡献变小;热阻随环境温度的上升而减小,其原因是二氧化硅埋氧层的导热率随温度的升高而增大。  相似文献   

3.
运用电学测试法,以两款不同封装类型功率VDMOS为实验对象,考察了耗散功率和环境温度对器件稳态热阻值的影响。结果表明:器件热阻值不是一个恒定不变的常量,由于电流拥挤效应,材料导热系数等条件的改变,它会随耗散功率及环境温度的增大而增大。该研究加深了对功率器件热阻理论的认识,为功率VDMOS的热特性评估提供了可靠的依据。  相似文献   

4.
电热激励微悬臂梁谐振器输出电压影响因素研究   总被引:2,自引:0,他引:2  
制作了电热激励硅 /二氧化硅双层微悬臂梁谐振器。对影响谐振器输出电压的因素研究结果表明 :减小梁宽度、硅层厚度、环境气压和温度 ,可增大微悬臂梁谐振器输出电压 ;输出电压随激励功率增加而增大 ;谐振器输出电压与谐振器根部压敏电桥电源电压成正比。最后论述了提高谐振器输出电压的可行途径  相似文献   

5.
专利     
二次谐波发生器由非线性双折射晶体器件谐振器和温控单元组成。用基波的偏振光照射到非线性双折射晶体器件产生二次谐波。规定谐振器的环境温度达到适当的温度使谐振器达到热稳定。通过调节器件的温度,使双折射晶体器件温度上升。(美国专利号:5495489)  相似文献   

6.
该文在硅酸镓镧(LGS)声表面波(SAW)谐振器上沉积了不同厚度的聚酰亚胺薄膜,研究了聚酰亚胺覆盖层对LGS声表面波谐振器的影响。结果表明,SAW谐振器表面沉积了聚酰亚胺薄膜后,器件的谐振频率向低频移动,且随着聚酰亚胺层厚度的增加,谐振器的谐振频率下降越大。SAW谐振器的一阶频率温度系数绝对值随着聚酰亚胺层厚度的增加而增大,且温度转变点向低温偏移。研究结果表明,覆盖聚酰亚胺层薄膜可以提高SAW谐振器的温度灵敏度,从而可应用于温度传感器中。  相似文献   

7.
为了满足射频器件的高频率、高功率和微小型化的需求,该文采用有限元分析软件COMSOL Multiphysics设计了一个谐振频率为3.455 GHz的牢固安装型谐振器(SMR)二维模型,研究了不同电极面积(200 μm2、150 μm2、100 μm2、50 μm2、25 μm2)对谐振器横向寄生谐振的影响,并对比了上电极变化和上、下电极同时变化对器件横向寄生谐振程度的影响。结果表明,器件在谐振点(3.455 GHz)附近的横向寄生谐振随电极面积的减小而增加,当电极面积为25 μm2时,器件的横向寄生谐振现象最显著;当电极面积的变化量一定时,同时改变上、下电极面积的横向寄生谐振大于只改变上电极面积产生的横向寄生谐振。  相似文献   

8.
利用离子注入剥离法(CIS)制备的铌酸锂(LN)压电薄膜可用于制备体声波(BAW)器件,近年来备受关注。滤波器的指标与谐振器的性能密切相关,但基于LN单晶薄膜的BAW谐振器,对其结构的仿真优化还未有较深入的报道。该文以LN单晶薄膜为核心压电层材料,构建了固态反射型(SMR)单晶薄膜谐振器有限元仿真模型,对其压电层厚度和布喇格反射层厚度进行了设计,并重点针对谐振器上电极的台阶结构进行了二维模型仿真,为高频LN BAW滤波器的制备提供了理论依据。  相似文献   

9.
研究了铁电薄膜红外探测器响应率等器件参数随铁电薄膜厚度的变化.器件的隔热层结构采用气凝胶二氧化硅.实验发现器件的热释电系数,吸收率以及热导均随膜厚增加而增加.铁电膜层厚度为240nm的器件,其热导与微桥结构器件的热导相近,都为10-7W/K量级,证明气凝胶二氧化硅做隔热层能够制备出性能优良的热释电红外探测器.随着薄膜厚度增加,热导急剧增大,这是引起器件响应率降低的原因.制备铁电薄膜过程中的多次650°高温退火可能降低了二氧化硅多孔率.  相似文献   

10.
刘艳  颜静  王洪娟  韩根全 《半导体学报》2014,35(2):024001-4
在Si(110)衬底上制备了Ge源n型Si沟道隧穿场效应晶体管(TFET)。本文研究了温度对Ge源Si TFET器件的电学性能的影响。温度相关性研究显示器件漏电流主要由漏区的Shockley - Read - Hall (SRH) 产生于复合电流决定。器件开态电流随温度升高而增加,这是因为温度升高材料禁带宽度减小,隧穿几率增大。界面缺陷引起的隧穿电流的亚阈值摆幅随温度升高而变差,但是带间隧穿电流的亚阈值摆幅不随温度变化而变化。  相似文献   

11.
DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.  相似文献   

12.
This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel's.  相似文献   

13.
The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.  相似文献   

14.
Today, micro-system technology and the development of new MEMS (Micro-Electro-Mechanical Systems) are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.  相似文献   

15.
The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.  相似文献   

16.
From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.  相似文献   

17.
It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output(MIMO) communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.  相似文献   

18.
Waveguide multilayer optical card (WMOC) is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling & processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic (VB) language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.  相似文献   

19.
The effect of laser microbeam trapping the bioparticles has been appfied widely in the biology .However the micromechanism of the acting that realizes the laser-microbeam trapping bioparticles is still lacking. In this paper ,the act microchenism of the gradiant force of laser microbeam for the bioparticles is analysed by means of quantum theory ,The result accords with our experiment.  相似文献   

20.
In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal (200) (2d = 0.4027 nm) is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line(w), the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line(x), the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines(y), the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line(z) in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line(q) in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution(λ/△ 2) is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号