HEMT太赫兹探测器的二维电子气特性分析

采用分子束外延技术(MBE)对GaAs/Al_xGa_(1-x)As二维电子气(2DEG)样品进行了制备,样品制备过程中,通过改变Al的组分含量、隔离层厚度、对比体掺杂与δ掺杂两种方式,在300 K条件下对制备的样品进行了霍尔测试,获得了室温迁移率7.205E3cm~2/Vs,载流子浓度为1.787E12/cm~3的GaAs/Al_xGa_(1-x)As二维电子气沟道结构,并采用Mathematica软件分别计算了不同沟道宽度时300 K、77 K温度下GaAs基HEMT结构的太赫兹探测响应率,为HEMT场效应管太赫兹探测器的研究和制备提供了参考依据.     

分子束外延GaAs基M-HEMT与Si基HEMT材料研究北大核心

在GaAs基渐变缓冲层高迁移率晶体管(M-HEMT)器件中,二维电子气的输运性能对器件性能有决定性作用。系统研究了GaAs M-HEMT材料中不同In组分沟道和生长温度对沟道电子迁移率和薄层电子浓度的影响。结果表明,沟道In组分为0.65时,材料电学性能最好;提高生长温度能有效提高材料的迁移率。为了后续将Si CMOS技术与HEMT材料结合实现高集成度应用,将M-HEMT结构外延在硅衬底上并得到了初步的研究结果,室温下电子迁移率为3300 cm^(2)/(V·s),薄层电子浓度为4.5×10^(12)cm^(-2)。     

MOCVD生长的SiC衬底高迁移率GaN沟道层AlGaN/AlN/GaN HEMT结构

用MOCVD技术在高阻6H-SiC衬底上研制出了具有高迁移率GaN沟道层的AlGaN/AlN/GaN高电子迁移率晶体管(HEMT)结构材料,其室温和80K时二维电子气迁移率分别为1944和11588cm2/(V·s),相应二维电子气浓度为1.03×1013cm-2;三晶X射线衍射和原子力显微镜分析表明该材料具有良好的晶体质量和表面形貌,10μm×10μm样品的表面粗糙度为0.27nm.用此材料研制出了栅长为0.8μm,栅宽为1.2mm的HEMT器件,最大漏极饱和电流密度和非本征跨导分别为957mA/mm和267mS/mm.     

MOCVD生长的SiC衬底高迁移率GaN沟道层AlGaN/AlN/GaN HEMT结构

用MOCVD技术在高阻6H-SiC衬底上研制出了具有高迁移率GaN沟道层的AlGaN/AlN/GaN高电子迁移率晶体管(HEMT)结构材料,其室温和80K时二维电子气迁移率分别为1944和11588cm2/(V·s),相应二维电子气浓度为1.03×1013cm-2;三晶X射线衍射和原子力显微镜分析表明该材料具有良好的晶体质量和表面形貌,10μm×10μm样品的表面粗糙度为0.27nm.用此材料研制出了栅长为0.8μm,栅宽为1.2mm的HEMT器件,最大漏极饱和电流密度和非本征跨导分别为957mA/mm和267mS/mm.     

AlGaN/GaN HEMT器件工艺的研究进展

首先论述了Al GaN/GaN高电子迁移率晶体管(HEMT)在微波大功率领域的应用优势和潜力;其次,介绍并分析了影响Al GaN/GaN HEMT性能的主要参数,分析表明要提高Al-GaN/GaN HEMT的频率和功率性能,需改善寄生电阻、电容、栅长和击穿电压等参数。然后,着重从材料结构和器件工艺的角度阐述了近年来Al GaN/GaN HEMT的研究进展,详细归纳了目前主要的材料生长和器件制作工艺,可以看出基本的工艺思路是尽量提高材料二维电子气的浓度和材料对二维电子气的限制能力的同时减小器件的寄生电容和电阻,增强栅极对沟道的控制能力。另外,根据具体情况调节栅长及沟道电场。最后,简要探讨了Al GaN/GaN HEMT还存在的问题以及面临的挑战。     

半导体技术

TN301,TN304 00020364HEMT的材料结构和二维电子气浓度的关系/李效白,崔立奇,张文俊,贾海强(电子部13所)11半导体情报,一1 999,36(2)一33一38给出了HEMT和PHEMT的数学一物理模型.系统地描述了材料的隔离层、平面调制掺杂层、势垒耗尽层等材料结构尺寸和异质结界面二维电子气浓度及器件沟道电流之间的相互关系。图3表1参12(午)与温度的关系.结果表明,电离杂质散射对霍耳迁移率与温度的关系有很大的影响.霍耳迁移率的低温值主要由电离杂质散射确定,而它的高温尾取决于声学声子,极化光学声子和谷间声子散射.计算的霍耳迁移率与实验数据…     

微波功率双异质结高电子迁移率晶体管

研制和测试了K波段频率范围的微波高电子迁移率晶体管(HEMT)。这种HEMT具有选择低掺杂(AlGa)As/GaAs/(AlGa)As双异质结的独特结构,它可同时获得大电流密度和高的栅击穿电压。这种结构在室温下电子迁移率达6800cm~2/V.s,二维(2-D)电子密度高达1.2×10~(12)cm~(-2)。橱长为1μm,总栅宽为1.2mm的器件,在20GHz下输出功率达660mW(550mW/mm),相关增益为3.2dB,功率附加效率为19.3％。栅宽为2.4mm的同样器件得到1W的输出功率,3dB的增益以及15.5％的效率。这些结果表明了双异质结HEMT(DH-HEMT)的微波大功率的能力。     

用于高性能MESFET的高迁移率In_(0.53)Ga_(0.47)As

用液相外延法生长了高纯 In_(0·53)Ga_(0·47)As 外延层,其室温电子迁移率高至13,800cm~2/v·s,相应的净电子浓度在10~(15)cm~(-3)的低端。至今所测得的最高78°K 迁移率约70,000cm~2/v·s,其净电子浓度为3.4×10~(14)cm~(-3)。这样高的迁移率能显著改善常断型 FET 的性能。推导出 In_(0·53)Ga_(0·47)As 的肖特基势垒高度约0.28ev,这就使栅极漏泄较大。提出一种新结构,它能减小栅极漏泄,并且,即使正栅偏压很小时,也能把电子限制到 In_(0·53)As 沟道内。这种结构是在 InGaAs 沟道与金属栅之间用了一层 n~--InP 外延层。     

调制掺杂对AlGaN/GaN HEMT材料电学性能的影响

利用范德堡Hall方法和汞探针C-V方法,研究了不同Si调制掺杂浓度对AlGaN/GaN HEMT材料电学性质的影响.发现si掺杂可以改善材料电学性能,二维电子气(2DEG)面密度和方块电阻(ns×μ)可以通过si调制掺杂精确控制.当Si掺杂浓度为3×10(18)cm-3时,得到了最低的方块电阻360Ω/□.尽管受到高浓度电子和离化杂质对二维电子气的散射影响,迁移率仍可达1220cm2/(V·s).分析了范德堡Hall方法和汞探针C-V方法的差别,同时测得材料的阈值电压也在合理范围.     

高电子迁移率晶体管(HEMT)

<正>用N-Al_xGa_(1-x)As/GaAs异质结构材料制造的高电子迁移率晶体管(HEMT),由于利用了异质结界面二维电子气的高电子迁移率等特点,较好地处理了GaAs MESFET技术中有源层内杂质散射与电子迁移率的矛盾,成为目前高速半导体器件中最有前途的新军,受到广泛重视.中国科学院物理研究所分子束外延组与南京固体器件研究所为了促进我国微波通讯事业等的发展,决定联合试制HEMT.现已获得初步实验结果:器件最大跨导值已超过100mS/mm,并进行了微波性能测试.     

Recessed-gate structure approach toward normally off high-Voltage AlGaN/GaN HEMT for power electronics applications

A recessed-gate structure has been studied with a view to realizing normally off operation of high-voltage AlGaN/GaN high-electron mobility transistors (HEMTs) for power electronics applications. The recessed-gate structure is very attractive for realizing normally off high-voltage AlGaN/GaN HEMTs because the gate threshold voltage can be controlled by the etching depth of the recess without significant increase in on-resistance characteristics. With this structure the threshold voltage can be increased with the reduction of two-dimensional electron gas (2DEG) density only under the gate electrode without reduction of 2DEG density in the other channel regions such as the channel between drain and gate. The threshold-voltage increase was experimentally demonstrated. The threshold voltage of fabricated recessed-gate device increased to -0.14 V while the threshold voltage without the recessed-gate structure was about -4 V. The specific on-resistance of the device was maintained as low as 4 m/spl Omega//spl middot/cm/sup 2/ and the breakdown voltage was 435 V. The on-resistance and the breakdown voltage tradeoff characteristics were the same as those of normally on devices. From the viewpoint of device design, the on-resistance for the normally off device was modeled using the relationship between the AlGaN layer thickness under the gate electrode and the 2DEG density. It is found that the MIS gate structure and the recess etching without the offset region between recess edge and gate electrode will further improve the on-resistance. The simulation results show the possibility of the on-resistance below 1 m/spl Omega//spl middot/cm/sup 2/ for normally off AlGaN/GaN HEMTs operating at several hundred volts with threshold voltage up to +1 V.     

沟道电场分布对AlN/GaN HFETs极化库仑场散射的影响

Based on the measured capacitance–voltage(C–V) curves and current–voltage(I–V) curves for the prepared differently-sized Al N/Ga N heterostructure field-effect transistors(HFETs), the I–V characteristics of the Al N/Ga N HFETs were simulated using the quasi-two-dimensional(quasi-2D) model. By analyzing the variation in the electron mobility for the two-dimensional electron gas(2DEG) with the channel electric field, it is found that the different polarization charge distribution generated by the different channel electric field distribution can result in different polarization Coulomb field(PCF) scattering. The 2DEG electron mobility difference is mostly caused by the PCF scattering which can reach up to 899.6 cm2/(V s)(sample a), 1307.4 cm2/(V s)(sample b),1561.7 cm2/(V s)(sample c) and 678.1 cm2/(V s)(sample d), respectively. When the 2DEG sheet density is modulated by the drain–source bias, the electron mobility for samples a, b and c appear to peak with the variation of the 2DEG sheet density, but for sample d, no peak appears and the electron mobility rises with the increase in the2 DEG sheet density.     

InAlN/GaN HEMTs: a first insight into technological optimization

High-electron mobility transistors (HEMTs) were fabricated from heterostructures consisting of undoped In/sub 0.2/Al/sub 0.8/N barrier and GaN channel layers grown by metal-organic vapor phase epitaxy on (0001) sapphire substrates. The polarization-induced two-dimensional electron gas (2DEG) density and mobility at the In/sub 0.2/Al/sub 0.8/N/GaN heterojunction were 2/spl times/10/sup 13/ cm/sup -2/ and 260 cm/sup 2/V/sup -1/s/sup -1/, respectively. A tradeoff was determined for the annealing temperature of Ti/Al/Ni/Au ohmic contacts in order to achieve a low contact resistance (/spl rho//sub C/=2.4/spl times/10/sup -5/ /spl Omega//spl middot/cm/sup 2/) without degradation of the channels sheet resistance. Schottky barrier heights were 0.63 and 0.84 eV for Ni- and Pt-based contacts, respectively. The obtained dc parameters of 1-/spl mu/m gate-length HEMT were 0.64 A/mm drain current at V/sub GS/=3 V and 122 mS/mm transconductance, respectively. An HEMT analytical model was used to identify the effects of various material and device parameters on the InAlN/GaN HEMT performance. It is concluded that the increase in the channel mobility is urgently needed in order to benefit from the high 2DEG density.     

最大振荡频率640 GHz的70 nm栅长InAs PHEMTs器件

由于高的电子迁移率和二维电子气浓度,InP基赝配高电子迁移率晶体管（PHEMTs）器件成为制作太赫兹器件最有前途的三端器件之一。为提高器件的工作频率,采用InAs复合沟道,使得二维电子气的电子迁移率达到13000 cm2/（Vs）。成功研制出70 nm栅长的InP基赝配高电子迁移率晶体管,器件采用双指,总栅宽为30 m,源漏间距为2 m。为降低器件的寄生电容,设计T型栅的栅根高度达到210 nm。器件的最大漏端电流为1440 mA/mm （VGS=0.4 V）,最大峰值跨导为2230 mS/mm。截止频率fT和最大振荡频率fmax分别为280 GHz和640 GHz。这些性能显示该器件适于毫米波和太赫兹波应用。     

GaAs基InAs/AlSb二维电子气结构的生长优化

采用分子束外延设备 (MBE) , 外延生长了InAs/AlSb二维电子气结构样品.样品制备过程中, 通过优化AlGaSb缓冲层厚度和InAs/AlSb界面厚度、改变AlSb隔离层厚度, 分别对比了材料二维电子气特性的变化, 并在隔离层厚度为5nm时, 获得了室温电子迁移率为20500cm2/V·s, 面电荷密度为2.0×1012/cm2的InAs/AlSb二维电子气结构样品, 为InAs/AlSb高电子迁移率晶体管的研究和制备提供了参考依据.     

AlGaN/GaN/AlGaN双异质结材料生长及性质研究

基于能带理论设计并利用MOCVD技术在76.2 mm蓝宝石衬底上生长了不同GaN沟道层厚度的AlGaN/GaN/AlGaN双异质结材料.室温霍尔测试结果表明:双异质结材料的二维电子气面密度随沟道层厚度增加有所升高并趋于饱和;二维电子气迁移率则随沟道厚度增加明显升高.200 nm厚GaN沟道的双异质结材料方块电阻平均值3...     

Design and characteristics of InGaAs/InP composite-channel HFET's

A design for composite-channel structures consisting of an InGaAs channel and an InP subchannel for use as heterostructure field-effect transistors is presented for the first time. This novel channel structure takes advantage of both the high drift velocity and low impact ionization of InP at high electric fields as well as the high electron mobility of InGaAs at low electric fields. It is shown that the doping density of the InP subchannel is the key parameter to realize the advantages of the composite channel. A very high transconductance of 1.29 S/mm and a current gain cutoff frequency of 68.7 GHz are achieved with 0.6 and 0.7 /spl mu/m gates, respectively. The average velocity of electrons in the composite channel is 2.9/spl times/10/sup 7/ cm/s. The devices have no kink phenomena in their I-V characteristics possibly due to low impact ionization in the InP subchannel.<>     

分子束外延AlGaN/GaN异质结场效应晶体管材料

用自组装的氨源分子束外延 (NH3-MBE)系统和射频等离子体辅助分子束外延 (PA-MBE)系统在 C面蓝宝石衬底上外延了优质 Ga N以及 Al Ga N/Ga N二维电子气材料。Ga N膜 (1 .2 μm厚 )室温电子迁移率达3 0 0 cm2 /V· s,背景电子浓度低至 2× 1 0 1 7cm- 3。双晶 X射线衍射 (0 0 0 2 )摇摆曲线半高宽为 6arcmin。 Al Ga N/Ga N二维电子气材料最高的室温和 77K二维电子气电子迁移率分别为 73 0 cm2 /V·s和 1 2 0 0 cm2 /V· s,相应的电子面密度分别是 7.6× 1 0 1 2 cm- 2和 7.1× 1 0 1 2 cm- 2 ;用所外延的 Al Ga N/Ga N二维电子气材料制备出了性能良好的 Al Ga N/Ga N HFET(异质结场效应晶体管 ) ,室温跨导为 5 0 m S/mm(栅长 1 μm) ,截止频率达 1 3 GHz(栅长 0 .5μm)。该器件在 3 0 0°C出现明显的并联电导 ,这可能是材料中的深中心在高温被激活所致