一种齐纳二极管控制式轨对轨CMOS运算放大器

采用0.6μm CMOS工艺,设计了一种齐纳二极管控制式轨对轨运算放大器.该运放采用了3.3V单电源供电,其输入共模范围和输出信号摆幅接近于地和电源电压,即所谓输入和输出电压范围轨对轨.该运放的小信号增益为82dB,单位增益带宽为12.34MHz,相位裕度为68°.由于电路简单,工作稳定,输入输出线性动态范围宽,非常适合于SOC芯片内集成.文中主要讨论该轨对轨运算放大器的原理,性能及设计方法,并进行了模拟仿真.     

一种轨对轨CMOS运算放大器的设计

基于0.6μmCMOS工艺,设计了一种轨对轨运算放大器。该运算放大器采用了3.3V单电源供电,其输入共模范围和输出信号摆幅接近于地和电源电压,即所谓输入和输出电压范围轨对轨。该运放的小信号增益为77dB,单位增益带宽为4.32MHz,相位裕度为79°。由于电路简单,工作稳定,输入输出线性动态范围宽,非常适合于SOC芯片内集成。     

采用输入信号适配技术的BiCMOS运放

为了满足高性能开关电源中集成运放的应用需要,设计了一种结构简单且具有轨对轨输出的运算放大器.该运放基于0.5μm BiCMOS 工艺,采用浮动输出的输入信号适配器(ISAFO),将输入信号放大至差分输入级的工作区域,从而实现了轨对轨的运行.对所设计的运放进行了仿真分析,结果表明在工作电源电压为±0.75 V、外接100 kΩ电阻的条件下,该运放的直流开环增益达到了102 dB,单位增益-带宽为6.35 MHz,相位裕度为62.5°,而功耗仅约为150 μW.所设计的运放具有很宽的共模输入范围及较高的增益,所以特别适用于开关电源的误差放大器、过流、过压和过热保护模块中.     

一种低电压恒定跨导轨到轨运算放大器的设计

设计了一种低电压恒定跨导的轨到轨运算放大器,作为误差放大器用在BUCK型DC-DC上实现对输出电压的调节。该运算放大器采用两级结构,输入级采用互补差分对的结构,实现了轨到轨电压的输入,并且利用2倍电流镜技术实现了跨导的恒定;输出级采用AB类放大器的结构,提高了输出电压摆幅和效率,实现了轨到轨电压的输出。该电路基于CSMC 0.25μm EN BCDMOS工艺进行设计,仿真结果表明:电源电压为2.8 V时,在输出端负载电容为160 pF、负载电阻为10 kΩ的情况下,增益为124 dB,单位增益带宽积为5.76 MHz,相位裕度为59.9℃,输入跨导为5.2 mΩ~(-1),共模抑制比为123 dB,输入共模信号范围为0～2.8V,输出电压摆幅为0～2.8 V。     

一种轨至轨输入的低压低功耗运放的设计

本文采用0.35μm的CMOS标准工艺,设计了一种轨至轨输入,静态功耗150μW,相位增益86dB,单位增益带宽2.3MHz的低压低功耗运算放大器。该运放在共模输入电平下有着几乎恒定的跨导,使频率补偿更容易实现,可应用于VLSI库单元及其相关技术领域。     

一种恒跨导轨对轨CMOS运算放大器的设计

设计了一种新颖的恒跨导轨对轨CMOS运算放大器结构。输入级采用轨对轨的结构,在输入级采用4个虚拟差分对管来对输入差分对的电流进行限制,使运放的输入级跨导在工作范围内保持恒定。输出级采用前馈式AB类输出结构,以使输出达到全摆幅。仿真结果显示,在5 V电源电压和带有10 pF电容与10 kΩ电阻并联的负载下,该运放在共模输入范围内实现了恒跨导,在整个共模输入范围内跨导变化率仅为3%,输出摆幅也达到了轨对轨全摆幅,运放的开环增益为108.5 dB,增益带宽积为26.7 MHz,相位裕度为76.3°。     

低功耗恒定跨导轨对轨运算放大器设计技术研究

为了解决轨对轨运算放大器输入级跨导随共模输入电压变化的影响,采用实时共模电压监测技术,动态跟踪轨对轨运放输入级的跨导变化,通过对偏置电流的高精度定量补偿,从而实现了对输入级跨导的恒定性控制。基于0.18μm CMOS工艺进行了具体电路的设计实现,结果表明:在电源电压3.3 V、负载电阻100Ω、负载电容1 nF的条件下,运放增益为148 dB、相位裕度为61°、功耗为39.6μW,共模输入范围高达0~3.3 V,输入级跨导变化率仅为2.1%。     

轨到轨输入输出范围运算放大器的噪声分析和优化

这篇文章设计了一个轨到轨（Rail-to-Rail）输入输出范围的低噪声运算放大器,在输入级采用电流补偿的方法来稳定该运算放大器在整个输入共模范围内的跨导,在输出级使用了AB类的输出方法来提高运算放大器的输出范围,且详细分析了该运算放大器的噪声性能,在此基础上给出了改善该运算放大器噪声性能的方法,以此来提高该运算放大器的动态范围。     

一种恒跨导CMOS运算放大器的设计

设计了一种宽带轨对轨运算放大器,此运算放大器在3.3 V单电源下供电,采用电流镜和尾电流开关控制来实现输入级总跨导的恒定。为了能够处理宽的电平范围和得到足够的放大倍数,采用用折叠式共源共栅结构作为前级放大。输出级采用AB类控制的轨对轨输出。频率补偿采用了级联密勒补偿的方法。基于TSMC 2.5μm CMOS工艺,电路采用HSpice仿真,该运放可达到轨对轨的输入/输出电压范围。     

基于单一PMOS差分对的轨到轨输入运算放大器设计

基于国内某CMOS工艺设计了一种单一PMOS差分对的轨到轨输入、恒跨导CMOS运算放大器。输入级电路采用折叠共源共栅结构,通过体效应动态调节输入管的阈值电压扩展共模输入范围到正负电源轨,恒定共模输入范围内的跨导,自级联电流镜有源负载将差分输入转换为单端输出;输出级电路采用AB类结构实现轨到轨输出,线性跨导环确定输出管的静态偏置电流。在5 V电源电压,2.5 V共模电压,1 MΩ负载条件下,经Spectre仿真验证,该运算放大器开环增益为119 dB,相位裕度为58°,共模输入范围为0.0027～4.995 V,共模范围内跨导变化小于3%,实现了轨到轨输入共模范围内的跨导恒定。     

电源自适应Rail-to-Rail CMOS运算放大器

基于CSMC 0.6 μm标准CMOS工艺,实现了一种电源自适应Rail-to-Rail CMOS运算放大器,其输入级从原理上变“被动地“适应低电压为“主动地“要求低电压.当外部电源电压在2.1V到3.2 V变化时,内部电源电压稳定在1.68 V,最大偏差为5.4%.这样,内部电源电压自适应地稳定在“相交条件“,实现了输入级的跨导Gm为常数:在整个共模(CM)电压变化范围内,输入级跨导的最大变化为9%.Rail-to-rail输出级用两个折叠网格和AB类反馈控制结构实现,使输出级的最低电源电压降到Vgs 2Vds,并使输出静态电流最小.     

Low-voltage operational amplifier with rail-to-rail input and output ranges

An operational amplifier is described which can perform precision signal operations in nearly the full supply voltage range, event when this range is as low as 1.5 V totally. The untrimmed input offset voltage is typically 0.3 mV in an input common-mode (CM) voltage range which extends beyond both supply voltages for about 200 mV. The output voltage can reach each supply rail within 150 mV. A nested-loop frequency-compensation scheme yields a stable unity-gain bandwidth of 0.6 MHz while the low-frequency open-loop voltage gain is 110 dB. The op amp is integrated in a standard low-cost bipolar process and the chip measures 1.5/spl times/1.7 mm/SUP 2/.     

0．6VCMOS轨至轨运算放大器

为适应低压低功耗设计的应用,设计了一种超低电源电压的轨至轨CMOS运算放大器。采用N沟道差分对和共模电平偏移的P沟道差分对来实现轨至轨信号输入．。当输入信号的共模电平处于中间时,P沟道差分对的输入共模电平会由共模电平偏移电路降低,以使得P沟道差分对工作。采用对称运算放大器结构,并结合电平偏移电路来构成互补输入差分对。采用0．13μm的CMOS工艺制程,在0．6V电源电压下,HSpice模拟结果表明,带10pF电容负载时,运算放大器能实现轨至轨输入,其性能为：功耗390μw,直流增益60dB,单位增益带宽22MHz,相位裕度80°。     

A high-frequency fully differential BiCMOS operational amplifier

A high-frequency fully differential BiCMOS operational amplifier design for use in switched-capacitor circuits is presented. The operational amplifier is integrated in a 3.0-GHz, 2-μm BiCMOS process with an active die area of 1.0 mm×1.2 mm. This BiCMOS op amp offers an infinite input resistance, a DC gain of 100 dB, a unity-gain frequency of 90 MHz with 45° phase margin, and a slew rate of 150 V/μs. The differential output range is 12 V. The circuit is operated from a ±5-V power supply and dissipates 125 mW. The op amp is unity-gain stable with 7 pF of capacitive loading at each output. The op amp is a two-stage, pole-split frequency compensated design that uses a PMOS input stage for infinite input resistance and an n-p-n bipolar second stage for high gain and high bandwidth. The frequency compensation network serves both the differential- and common-mode amplifiers so the differential- and common-mode amplifier dynamics are similar. A dynamic switched-capacitor common-mode feedback scheme is used to set the output common-mode level of the first and second stages     

A rail-to-rail CMOS op amp

A CMOS op amp (operational amplifier) is reported which has a rail-to-rail voltage range at its input as well as its output. An area-efficient output stage has been used. While the entire op amp occupies only 600 mil², when used as a unity-gain buffer and with ±5-V supplies, the op amp can drive a 9-V_pp/1-kHz sine wave across a 300-Ω load with -64 dB of harmonic distortion     

一种用于水听器电压检测的模拟前端电路

提出了一种用于水听器电压检测的模拟前端电路,包括低噪声低失调斩波运算放大器,跨导电容(gm-C)低通滤波器,增益放大器三部分主体电路;低噪声低失调斩波运算放大器用于提取水听器前端传感器输出的微弱电压信号;gm-C低通滤波器用于滤除电压信号频率外的高频噪声和高次谐波;最后经过增益放大器放大至后级模数转换器的输入电压范围,输出数字码流;芯片采用台积电(TSMC)0.18μm单层多晶硅六层金属(1P6M)CMOS工艺实现。测试结果表明,在电源电压1.8 V,输入信号25 kHz和200 kHz时钟频率下,斩波运放输入等效失调电压小于110μV;整体电路输出信号动态范围达到80 dB,功耗5.1 mW,满足水听器的检测要求。     

Operational amplifier with 1-V rail-to-rail multipath-driven outputstage

A bipolar operational amplifier (op amp) with a rail-to-rail multipath-driven output stage that operates at supply voltages down to 1 V is presented. The bandwidth of this output stage is as high as possible, viz, equal to that of one of the output transistors, loaded by the output capacitance. The output voltage can reach both supply rails within 100 mV and the output current is ±15 mA. The op amp is designed to be loaded by a 100-pF capacitor and the unity-gain bandwidth is 3.4 MHz at a 60° phase margin. The voltage gain is 117 dB and the CMRR is 100 dB. The frequency behavior of the multipath-driven (MPD) topology has an improved performance when compared to that of previously presented low-voltage output stages. A figure of merit F_M for low-voltage op amps has been defined as the bandwidth-power ratio     

A rail-to-rail, constant gain, buffered op-amp for real time videoapplications

Inspired by Hogervorst et al's current switch idea, a buffered output stage operational amplifier was designed, which has high frequency, high dc gain, and rail-to-rail constant transconductance (G _m). This operational amplifier is the output stage of an analog/digital system which implements a Gabor convolution for real-time dynamic image processing and it is designed to interface the external analog-to-digital converter (ADC) with a very heavy load. The op amp was fabricated by the MOSIS service in a 2-μm, n-well CMOS, double polysilicon, double metal technology. The fabricated circuit operates from a single 5 V power supply and dissipates 10 mW. The open loop-gain of the fabricated circuit, A_vol, was measured as 67.2 dB for a 163 Ω∥33 pF load. Other dc and ac characteristics were measured for a 50 Ω∥33 pF load. The unify gain-bandwidth (GBW) was measured to be 11.4 MHz, the rising slew rate (SR+) 20.4 V/μs, the falling slew rate (SR-) 18.8 V/μs, and the offset voltage (V_off) 1 mV. The output swings with an amplitude of 3.24 V between 0.88 V and 4.12 V, which matches the input signal specifications of the ADC. In addition to rail-to-rail output voltage swing, the opamp has a constant G_m over the whole common mode (CM) voltage range     

High-speed GaAs operational amplifier

An operational amplifier has been designed and fabricated using GaAs MESFETs. This amplifier is a general-purpose monolithic GaAs op amp designed as as a stand-alone component. The amplifier has a differential input, an open-loop gain in excess of 60 dB, and is internally compensated. The high open-loop gain (60 dB at 100 kHz) was achieved by using gain stages with positive feedback. The op amp incorporates a current-mirror level-shifting stage which allows the op amp to operate over a wide power-supply range (/spl plusmn/5-9 V). Previous designs have diodes to achieve level shifting, a practice that precludes operation over a wide supply range. This op amp is a true analog to its silicon counterparts, but it has a higher gain-bandwidth product.