一种基于滤波多音系统的半盲同步算法

该文在研究滤波多音(Filtered MultiTone,FMT)调制性质的基础上,给出了一种新的FMT系统定时同步算法。该算法将FMT符号的相关性和PN序列强自相关性结合,在保证算法性能的同时,大大缩短了构造同步符号所需训练序列的长度。此外,该文还提出了一种简单有效的整数倍子载波间隔频偏的估计算法。仿真结果表明,这两种算法在加性高斯噪声信道中性能优良,结合分集技术在多普勒频移的瑞利信道下也获得良好的估计性能。     

FMT系统中的迭代信道估计和Turbo均衡

在滤波多音调制(FMT)系统中,为了消除由于原型滤波器非理想重构特性和多径信道所导致的符号间干扰,提出了一种联合迭代信道估计和Turbo均衡的FMT系统接收方法,通过对FMT系统中每个子信道的等效冲激响应进行迭代估计,然后采用基于线性滤波器结构的Turbo均衡器来消除符号间干扰.仿真结果表明,不论采用QPSK调制方式还是16QAM调制方式,经过2次以上的迭代后,相比较于传统的判决反馈均衡算法,新算法的误码率性能得到了大大改善.     

基于隐训练序列的MIMO通信系统信道估计与跟踪

针对MIMO通信系统的信道估计与跟踪问题,提出了一种基于隐训练序列(ITS)的信道估计算法,分析了该算法的均方误差性能,给出了训练序列的优化方案.仿真表明,该算法与传统的最小二乘信道估计算法、预编码隐训练序列算法相比,具有估计精度高、计算量低、易于优化训练序列等特点,且算法不受接收端存在直流偏移的影响,其自适应结构能够很好地实现对快时变通信信道的跟踪,对解决电子战中快时变通信信道的捕获和跟踪问题具有一定的指导意义和应用价值.     

一种适用于终端移动的OFDM无线局域网的信道估计方法

本文提出了一种适用于具有移动终端的OFDM无线局域网的信道估计方法.该方法采用了卡尔曼滤波算法进行了信道估计,并利用导频进行信道跟踪.将基于训练序列的信道估计结果作为Kalman滤波器的初始值和观测值,用基于导频的信道估计结果来计算Kalman滤波器参数.并利用导频进一步跟踪信道在时间上的变化.Simulink仿真结果表明,该算法比基于导频的信道估计方法和基于训练序列的信道估计方法效果都要好.     

隐含训练序列信道估计中的功率分配

与传统时分发送训练序列的信道估计算法相比,隐含训练序列信道估计算法将训练序列与信息序列直接相加后通过天线发送,从而节约了信道带宽.然而,在天线发送总功率一定时,训练序列的功率越大,信息序列的功率便越小,从而导致信道均衡器的信噪比减小.本文研究了基于MIMO系统的隐含训练序列信道估计算法,分析了信道均衡器信噪比与训练序列功率的关系,并根据均衡器信噪比最大原则推导出训练序列与信息序列的最佳功率分配.分析和仿真结果表明:在训练序列的最佳功率点上,信道均衡器的信噪比最高;随着接收天线信噪比的增加,训练序列的最佳功率增大.     

基于叠加训练序列快速信道辨识方法

信道状态信息(CSI)对于无线通信来说至关重要,而叠加训练序列的信道估计方法由于不占用额外的信号带宽和具有较高的估计精度而受到人们的注意.本文从算法的复杂度入手,分析了不同的训练序列对算法复杂度的影响,并且在训练序列为PN序列下,利用循环Toeplitz矩阵的特性,得到了信道估计的快速算法.仿真实验的结果表明,这种算法不需要矩阵求逆、计算量小,估计精度高,有很大的实际应用前景.     

一种基于PN序列的信道估计算法及SIMULINK仿真

提出了一种基于PN序列的LS信道估计算法。利用PN序列特殊的相关性,在接收端完成相关处理,从而获得多径衰落信道的状态参数。在SIMULINK搭建的OFDM-FH仿真模型中,运用该信道估计算法进行仿真。结果证明,在相同信噪比和信道利用率的条件下,基于PN序列的LS信道估计算法要比传统的LS算法具有更高的信道估计精度。     

TH-UWB系统中ML信道估计算法研究

跳时超宽带无线通信系统中信道估计的准确度对系统接收性能具有重要影响,首先对超宽带系统收发模型进行介绍,然后对TH-UWB系统中基于训练序列的非结构化最大似然信道估计算法进行分析,最后在超宽带信道模型下对估计算法性能进行仿真.仿真结果表明基于训练序列的非结构化最大似然信道估计算法能够有效估计出信道参数.     

智能天线中一种迭代的联合信道估计 与符号检测算法

在传统的二维RAKE接收机中,通常使用导频信道来估计信道矢量,进而求取加权系数,用于业务信道符号序列的检测.当导频功率较低时,信道估计误差较大,系统性能较差.本文提出了一种新的算法,先利用导频进行信道矢量的初始估计,然后用带投影的迭代最小二乘法,进行信道和符号序列的联合估计,该算法具有计算复杂度低,收敛速度快的特点.仿真结果表明:与传统二维RAKE接收机相比,该算法使系统的误码性能得到了有效改善.     

基于时域训练序列的MIMO系统信道估计算法研究

本文介绍了MIMO系统使用训练序列进行信道估计的方法。描述了基于时域训练序列的信道估计算法及采用遗传算法优化后的训练序列的信道估计算法。理论分析和仿真结果显示,后者性能更好,估计误差低于前者。     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Call for Papers

正Communications—VLSI Researches and industries of telecommunications have been growing rapidly in the last 20 years and will keep their high growing pace in the next decade.The involved researches and developments cover mobile communications,highway and last-mile broadband communication,domain specific communications,and emerging D2D M2M communications.Radio communication steps into its