首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 55 毫秒
1.
研制成功了可商业化的75mm单片超高真空化学气相淀积锗硅外延设备SGE500,并生长了器件级SiGe HBT材料.研制了具有优良小电流特性的多晶发射极双台面微波功率SiGe HBT器件,其性能为:β=60@VCE/IC=9V/300μA,β=100@5V/50mA,BVCBO=22V,ft/fmax=5.4GHz/7.7GHz@10指,3V/10mA.多晶发射极可进一步提供直流和射频性能的折衷,该工艺总共只有6步光刻,与CMOS工艺兼容且(因多晶发射极)无需发射极外延层的生长,这些优点使其适合于商业化生产.利用60指和120指的SiGe HBT制作了微波锗硅功率放大器.60指功放在900MHz和3.5V/0.2A偏置时在1dB压缩点给出P1dB/Gp/PAE=22dBm/11dB/26.1%.120指功放900MHz工作时给出了Pout/Gp/PAE=33.3dBm (2.1W)/10.3dB/33.9%@11V/0.52A.  相似文献   

2.
用于SiGeHBT器件的UHV/CVDn~-型硅外延研究   总被引:1,自引:0,他引:1  
利用超高真空化学气相淀积(UHV/CVD)设备,在掺Asn+型Si衬底上生长了掺Pn-型Si外延层.用扩展电阻法分析了在不同的生长温度和PH3气体流量下生长的Si外延层的过渡区厚度.结果表明,生长温度对n+-Si衬底的As外扩有明显影响,在700℃下生长的Si外延层的过渡区厚度为0.16μm,而在500℃下仅为0.06μm,且杂质分布非常陡峭.X射线双晶衍射分析表明在700℃下生长的Si外延层的质量很高.制作的锗硅异质结晶体管(SiGeHBT)的击穿特性很硬,击穿电压为14.5V,在VCB=14.0V下的漏电流仅为0.3μA;输出特性很好,在VCE=5V,IC=3mA时的放大倍数为60  相似文献   

3.
InP/InGaAs/InP DHBT具有频带宽、电流驱动能力强、线性好、相位噪声低和阈值电压一致性好等优点成为研究热点。通过优化外延材料结构设计和采用四元InGaAsP缓变层消除集电结电流阻塞效应;改进发射极-基极自对准工艺和集电区台面侧向腐蚀工艺,降低Rb和Cbc乘积;优化PI钝化工艺和空气桥互联等工艺,实现了发射极面积为2μm×10μm的自对准InP/InGaAs/InP DHBT器件,其直流增益β约为25,击穿电压BVCEO≥7 V@10μA,在VCE=4 V,Ic=10 mA下,截止频率fT=140 GHz,最高振荡频率fmax=200 GHz,优于同一外延片上的非自对准InP DHB器件,该器件将可应用于高速光通信和微波毫米波通信。  相似文献   

4.
本文首次报道采用重掺杂的氢化非晶硅(n~+a-Si∶H)作发射极的硅微波双极型晶体管的制备和特性.该器件内基区方块电阻2kΩ/□,基区宽度0.1μm,共发射极最大电流增益21(V_(cB)=6V,I_c=15mA),发射极Gummel数G_B值已达1.4×10~(14)Scm~(-4).由S参数测得电流增益截止频率f_s=5.5GHz,最大振荡频率f_(max)=7.5GHz.在迄今有关Si/a-Si HBT的报道中,这是首次报道可工作于微波领域里的非晶硅发射极异质结晶体管.  相似文献   

5.
L波段250W宽带硅微波脉冲功率晶体管   总被引:1,自引:1,他引:0  
南京电子器件研究所最近研制成功 L波段2 5 0 W宽带硅微波脉冲功率晶体管。该器件在 1 .2~ 1 .4GHz频带内 ,脉宽 1 5 0 μs,占空比 1 0 %和 40V工作电压下 ,全带内脉冲输出功率在 2 4 0~ 30 0W之间 ,功率增益大于 7.8d B,效率大于 5 0 %。器件设计为梳条状结构 ,单元间距 6μm,发射极和基极金属条条宽 2 .4μm,金属条间距 0 .6μm。每个器件由 6个尺寸为 1 60 0μm× 75 0μm功率芯片组成 ,每个功率芯片含有 2个子胞。整个器件包含 1 2个子胞、2 0个电容和 2 0 0多条连接金丝匹配而成。在微波功率发射等领域 ,硅微波脉冲大功率晶体管具…  相似文献   

6.
采用简单的双台面工艺制作了完全平面结构的5个单元、10个发射极指大面积的SiGe HBT.器件表现出了良好的直流和高频特性,最大电流增益β为214.BVCEO为9V,集电极掺杂浓度为1×1017 cm-3,厚度为400nm时,BVCBO为16V.在直流偏置下IC=30mA,VCE=3.0V得到fT和fmax分别为18.0GHz和19.3GHz,1GHz下最大稳定增益为24.5dB,单端功率增益为26.6dB.器件采用了新颖的分单元结构,在大电流下没有明显的增益塌陷现象和热效应出现.  相似文献   

7.
采用简单的双台面工艺制作了完全平面结构的5个单元、10个发射极指大面积的SiGe HBT.器件表现出了良好的直流和高频特性,最大电流增益β为214.BVCEO为9V,集电极掺杂浓度为1×1017 cm-3,厚度为400nm时,BVCBO为16V.在直流偏置下IC=30mA,VCE=3.0V得到fT和fmax分别为18.0GHz和19.3GHz,1GHz下最大稳定增益为24.5dB,单端功率增益为26.6dB.器件采用了新颖的分单元结构,在大电流下没有明显的增益塌陷现象和热效应出现.  相似文献   

8.
六边形发射极的自对准InGaP/GaAs异质结具有优异的直流和微波性能.采用发射极面积为2μm×10μm的异质结双极型晶体管,VCE偏移电压小于150mV,膝点电压为0.5V(IC=16mA),BVCEO大于9V,BVCBO大于14V,特征频率高达92GHz,最高振荡频率达到105GHz.这些优异的性能预示着InGaP/GaAs HBT在超高速数字电路和微波功率放大领域具有广阔的应用前景.  相似文献   

9.
介绍了Si衬底上外延生长GaN基HEMT的制备及其直流特性与微波特性的研究结果:栅宽200 μm器件Vgs=0 V时饱和电流密度达0.975 A/mm,最大跨导240 mS/mm,夹断电压-4.5 V,栅漏击穿电压80 V;栅宽1 mm器件,在频率2 GHz下,工作电压Vds=25 V时,连续波输出功率为5.0 W,功率增益为9 dB,功率附加效率为35%.  相似文献   

10.
高性能六边形发射极InGaP/GaAs异质结双极型晶体管   总被引:1,自引:1,他引:0  
六边形发射极的自对准In Ga P/ Ga As异质结具有优异的直流和微波性能.采用发射极面积为2μm×10μm的异质结双极型晶体管,VCE偏移电压小于15 0 m V,膝点电压为0 .5 V(IC=16 m A) ,BVCEO大于9V,BVCBO大于14 V,特征频率高达92 GHz,最高振荡频率达到10 5 GHz.这些优异的性能预示着In Ga P/ Ga As HBT在超高速数字电路和微波功率放大领域具有广阔的应用前景  相似文献   

11.
DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.  相似文献   

12.
The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.  相似文献   

13.
Today, micro-system technology and the development of new MEMS (Micro-Electro-Mechanical Systems) are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.  相似文献   

14.
The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.  相似文献   

15.
From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.  相似文献   

16.
This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel's.  相似文献   

17.
Waveguide multilayer optical card (WMOC) is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling & processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic (VB) language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.  相似文献   

18.
It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output(MIMO) communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.  相似文献   

19.
Due to variable symbol length of digital pulse interval modulation(DPIM), it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation(FDPIM) method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.  相似文献   

20.
The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号