Lpe growth of Hgl−xCdxTe using conventional slider boat and effects of annealing on properties of the epilayers

The epitaxial layers of Hg_1−xCd_xTe (0.17≦×≦0.3) were grown by liquid phase epitaxy on CdTe (111)A substrates using a conventional slider boat in the open tube H₂ flow system. The as-grown layers have hole concentrations in the 10¹⁷− 10¹⁸ cm⁻³ range and Hall mobilities in the 100−500 cm²/Vs range for the x=0.2 layers. The surfaces of the layers are mirror-like and EMPA data of the layers show sharp compositional transition at the interface between the epitaxial layer and the substrate. The effects of annealing in Hg over-pressure on the properties of the as-grown layers were also investigated in the temperature range of 250−400 °C. By annealing at the temperature of 400 °C, a compositional change near the interface is observed. Contrary to this, without apparent compositional change, well-behaved n-type layers are obtained by annealing in the 250−300 °C temperature range. Sequential growth of double heterostructure, Hg_l−xCd_xTe/Hg_l−yCd_yTe on a CdTe (111)A substrate was also demonstrated.     

Growth and properties of Hg1-x Cdx Te epitaxial layers

The growth of epitaxial layers of mercury-cadmium-telluride (Hg_1-xCd_xTe) with relatively low x (0.2-0.3) from Te-rich solutions in an open tube sliding system is studied. The development of a semiclosed slider system with unique features permits the growth of low x material at atmospheric pressure. The quality of the films is improved by the use of Cd_1-yZ_yTe and Hg_1-xCd_xTe substrates instead of CdTe. The substrate effects and the growth procedure are discussed and a solidus line at a relatively low temperature is reported. The asgrown epitaxial layers are p-type with hole concentration of the order of 1·10¹⁷ cm⁻³, hole mobility of about 300 cm²·V⁻¹ sec⁻¹ and excess minority carrier life-time of 3 nsec, at 77 K.     

Molecular beam epitaxy of CdTe and Hg1-xCdxTe ON GaAs (100)

Using the molecular beam epitaxial (MBE) technique, CdTe and Hg_1-xCd_xTe have been grown on Cr-doped GaAs (100) sub-strates. A single effusion cell charged with polycrystal-line CdTe is used for the growth of CdTe films. The CdTe films grown at 200 °C with a growth rate of ~ 2 μm/hr show both streaked and “Kikuchi” patterns, indicating single crystalline CdTe films are smoothly grown on the GaAs sub-strates. A sharp emission peak is observed at near band-edge (7865 Å, 1.577 eV) in the photoluminescence spectrum at 77 K. For the growth of Hg_1-xCd_xTe films, separate sources of HgTe, Cd and Te are used. Hg_0.6Cd_0.4Te films are grown at 50 °C with a growth rate of 1.7 μm/hr. The surfaces are mirror-smooth and the interfaces between the films and the substrates are very flat and smooth. As-grown Hg_0.6Cd_0.4Te films are p-type and converted into n-type by annealing in Hg pressure. Carrier concentration and Hall mobility of an annealed Hg_0.6Cd_0.4Te film are 1 × 10¹⁷ cm^?3 and 1000 cm²/V-sec at 77 K, respectively.     

Slider LPE of Hg1-xCdxTe using mercury pressure controlled growth solutions

Homogeneous, nearly perfect single crystals of Hg_1-xCd_xTe are extremely difficult to prepare due primarily to the high vapor pressure of mercury. However, epitaxially grown Hg_1-xCd_xTe layers have a high potential for yielding material of a substantially higher quality. Using a new, open-tube, horizontal slider-type liquid phase epitaxial (LPE) growth technique, in which mercury pressure controlled growth solutions are used, a high degree of growth solution compositional control has been demonstrated. LPE layers of Hg_1-xCd_xTe have been grown on CdTe substrates and their high quality has been confirmed by optical, transport and electron microprobe measurements. Layer thicknesses are uniform and have been varied from 5 to 40 μ by changing the degree of supercooling or the growth time. An electron carrier concentration as low as 8.6 × 10¹⁵/cm³ and electron Hall mobilities up to 2.8 × 105 cm²/V-sec at 77K have been measured on in situ annealed samples. This work was sponsored by the Department of the Air Force and the U.S. Army Research Office.     

Open-tube vapor transport epitaxy of Hg1−xCdxTe

A novel set-up for horizontal open-tube vapor transport epitaxy of Hg_1−xCd_xTe films is described. Mirror-like Hg_1−xCd_xTe epitaxial layers with thicknesses up to 40 Μm were grown and characterized. The growth temperature ranged from 380 to 550‡C, with growth rates of the order of 0.5–7 Μm per hour. The concentration depth profiles and the optical and electrical properties of relatively uniform films with x≈0.3–0.4 are reported. The process kinetics are studied. A simple model which takes into account the reactions occurring at the boundaries of the epitaxial layer and the interdiffusion in the epilayer is presented and discussed. The model fits the experimentally observed characteristics of the epitaxial growth process. A constant growth rate leading to a linear dependence of film thickness upon deposition time y–y_i=k_s t is derived. The reaction rate constant k is given by k_s=k_oe^−Ea^/kT with k_o=0.18 cm-sec⁻¹and the energy of activation E_a=1.12 eV.     

Molecular beam epitaxial growth of HgCdTe on CdZnTe(311)B

A series of n-type, indium-doped Hg_1−xCd_xTe (x∼0.225) layers were grown on Cd_0.96Zn_0.04Te(311)B substrates by molecular beam epitaxy (MBE). The Cd_0.96Zn_0.04Te(311)B substrates (2 cm × 3 cm) were prepared in this laboratory by the horizontal Bridgman method using double-zone-refined 6N source materials. The Hg_1−xCd_xTe(311)B epitaxial films were examined by optical microscopy, defect etching, and Hall measurements. Preliminary results indicate that the n-type Hg_1−xCd_xTe(311)B and Hg_1−xCd_xTe(211)B films (x ∼ 0.225) grown by MBE have comparable morphological, structural, and electrical quality, with the best 77 K Hall mobility being 112,000 cm²/V·sec at carrier concentration of 1.9×10⁺¹⁵ cm⁻³.     

Liquidus isotherms,solidus lines and LPE growth in the Te-rich corner of the Hg-Cd-Te system

Liquidus isotherms for the Hg_1−xCd_xTe primary phase field in the Te-rich corner of the Hg-Cd-Te ternary system have been determined for temperatures from 425 to 600‡C by a modified direct observational technique. These isotherms were used to help establish conditions for the open-tube liquid phase epitaxial growth of Hg_1−xCd_xTe layers on CdTe_1−ySe_y substrates. Layers with x ranging from 0.1 to 0.8 have been grown from Te-rich HgCdTe solutions under flowing H₂ by means of a horizontal slider technique that prevents loss of Hg from the solutions by evaporation. Growth temperatures and times of 450–550‡C and 0.25–10 min, respectively, have been used. The growth solution equilibration time is typically 1 h at 550‡C. Source wafers, supercooled solutions, and (111)-oriented substrates were employed in growing the highest quality layers, which were between 3 and 15 Μm thick. Electron microprobe analysis was used to determine x for the epitaxial layers, and the resulting data, along with the liquidus isotherms, were used to obtain solidus lines. In addition to EMP data, optical transmission results are given. This work was sponsored by the Department of the Air Force and the U. S. Army Research Office.     

Transient behavior of Hg1−xCdxTe film growth on (111)B CdTe substrates by chemical vapor transport

As part of a systematic investigation of the effects of substrate surfaces on epitaxial growth, the transient behavior of Hg_1−xCd_xTe film growth on (111)B CdTe by chemical vapor transport (CVT) has been studied as a function of growth time under vertical stabilizing (hot end on top) and vertical destabilizing (hot end at bottom) ampoule orientations. The experim ental results show the morphological transition of the Hg_1−xCd_xTe deposition on (111)B CdTe at 545°C from three-dimensional islands to layers within about 0.5 and 0.75 h for the growth under vertical stabilizing and destabilizing conditions, respectively. The combined effects of small convective flow disturbances on the growth morphology and defect formation are measurable. The overall trends of the time dependent growth rates and compositions of the Hg_1−xCd_xTe epitaxial layers under stabilizing and destabilizing conditions are similar. The system atically higher growth rates of the Hg_1−xCd_xTe films by about 10% under vertical destabilizing conditions could be influenced by a small convective contribution to the mass transport. The combined results show that improved Hg_1−xCd_xTe epitaxial layers of low twin density on (111)B CdTe substrates can be obtained by CVT under vertical stabilizing conditions.     

Transient behavior of Hg1−xCdxTe film growth on 3° off-(100) CdTe substrates by chemical vapor transport

The effects of substrate misorientation on Hg_1−xCd_xTe films, deposited on 3° off-(100) CdTe substrates by chemical vapor transport (CVT), have been studied for the first time using a transient growth technique. The morphological evolution of Hg_1−xCd_xTe films deposited on the vicinal CdTe substrates at 545°C shows a transition from three-dimensional islands to two-dimensional layer growth. The time and thickness required for the above morphological transition is about 0.75 h and 7 μm, respectively, under present experimental conditions. The pronounced long-range-terrace surface morphology of the Hg_1−xCd_xTe films illustrates the strong effects of the misorientation of the CdTe substrates and of the growth kinetics on the CVT growth of this hetero-epitaxial system. The transient behavior of the surface morphology, of the surface composition, and of the growth rate all reveal the influences of the 3° misorientation of the (100) CdTe substrates on the Hg_1−xCd_xTe epitaxy. The experimental mass flux results of the Hg_1−xCd_xTe-HgI₂ CVT system under transient and steady-state conditions can be related to the surface kinetics and to the thermodynamic properties of the system. The combined results show that the interface kinetics are not fixed in the transient regime and that they are coupled to the vapor mass transport.     

Passivation of Hg1-xCdxTe by photochemical native oxidation: Quantitative analysis of oxide composition

The composition of photochemically grown native oxides on Hg_1-xCd_xTe (x = 0.3) has been analyzed and depth profiled using x-ray photoelectron spectroscopy and Rutherford backscattering spectroscopy. The oxide films were grown in either N₂O or O₂ ambients, and differences in the oxidation process were examined by varying the time and temperature of oxide growth. Under all growth conditions, oxides grown in an O₂ ambient exhibited a higher Hg concentration in the bulk oxide region when compared to N₂O grown oxides. The Hg/Te ratio of all the oxides was found to be less than the starting Hg_1-xCd_xTe substrates and, in some cases, this may be leading to an accumulation of Hg in the oxide/Hg_1-xCd_xTe interface region. For growths at higher temperatures (∼75°C), the excess Hg was seen to move from the oxide/Hg_1-xCd_xTe interface region to the oxide surface. In O₂ ambients, the Hg accumulated at the surface of the oxide whereas for growths in N₂O, it was lost to the ambient. Previous results on photochemical oxidation of Hg_1-xCd_xTe show an inverse relationship between oxide growth rate and temperature. Evidence obtained in this study from oxide compositions, depth profiles and annealing at higher temperatures, suggest that this relationship between oxide growth rate and temperature is primarily due to temperature induced differences in the oxidizing ambient, and not the result of a change in the film growth mechanism due to changing diffusion characteristics with temperature.