首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 404 毫秒
1.
文章提出了一种对称结构的新型抗弯曲单模光子晶体光纤,采用全矢量有限元法分析了该光纤的单模特性及弯曲特性。在1 550nm波长处,光纤处于单模运转;当弯曲半径为5mm时,弯曲损耗仅为8.73×10-5 dB/圈;最小弯曲半径可达4.5mm,此时弯曲损耗为2.38×10-4 dB/圈;且无论光纤弯曲与否,其在1 550nm波长处的模场面积均约为61μm2,色散系数约为11.13ps/(nm·km),与普通单模光纤相匹配。  相似文献   

2.
张银  陈明阳  张永康 《中国激光》2012,39(12):1205001-108
通过在多模光子晶体光纤的两端分别连接一根单模光子晶体光纤,对其选择合适的参数,形成一种可以实现低弯曲损耗、大模场单模传输的光纤传输系统。运用数值仿真,分析了该传输系统在模场面积、弯曲损耗、连接损耗等方面的特性。研究结果表明,多模光子晶体光纤与单模光子晶体光纤所组成的系统可实现有效的单模传输;工作波长为1064nm时,多模光子晶体光纤在直波导状态时的基模模场面积可达1593μm2;在弯曲半径低至10cm时,多模光子晶体光纤仍然可以保持低损耗传输。经过对多模光子晶体光纤结构参数的优化,其与单模光子晶体光纤的连接损耗降低至0.085dB。  相似文献   

3.
单模光纤是在给定的工作波长中只传输单一基模的光纤,它不存在模式色散,所以具有相当宽的传输频带,运用于长距离大容量的传输.单模光纤的纤芯直径只有8~10 μm,包层直径为125 μm,可以制作得很长,但是为了制造、运输与施工的方便,通常光缆的出厂长度为1~6 km.单模光纤的传输损耗现低达0.2 dB/km(1.55 μm),光缆接续长度不宜小于2 km.  相似文献   

4.
提出了一种复合结构的光子晶体光纤,采用多极法对其双折射、限制损耗、基模模场以及色散特性进行了数值模拟.研究表明,该光纤在1 550 nm处可获得1.56×10-2的双折射,限制损耗为7.31×10-3 dB/km,负色散达-320 ps/(nm·km),且损耗在1 300~1 600 nm范围内基本稳定.  相似文献   

5.
介绍了一种新型非光子晶体结构弯曲不敏感单模光纤的设计与制备。采用数值计算方法分析了光纤的下陷型波导结构,通过PCVD(等离子体化学气相沉积法)工艺获得了1 310nm波长的模场直径为4.3μm、1 550nm波长的模场直径为5.4μm的光纤样品,与G.652D光纤的双点接续损耗低至0.15dB,满足普通跳线的接续要求。该样品在2.5mm弯曲半径条件下弯曲10圈,其1 550nm波长的弯曲损耗优化至0.01dB,可适用于任何苛刻的FTTx应用环境,并有替代铜缆成为消费电子中理想传输介质的潜力,同时还可用于各种光电器件中。  相似文献   

6.
文章作者设计并制造了一种纯硅芯高非线性光子晶体光纤,该光纤纤芯直径为1.65 μm,空气微孔直径为4.75 μm,孔中心间距为5.35 μm,零色散波长为1 120 nm,800 nm波长的色散为-88 ps/(nm·km).将能量为5 nJ、重复频率为100 MHz、中心波长为800 nm的30 fs的钛蓝宝石激光脉冲耦合入2 m长的该高非线性光子晶体光纤中,得到了450~1 400 nm宽波段范围内的超连续光谱.  相似文献   

7.
普通光纤与小芯径实芯光子晶体光纤的塌孔熔接技术   总被引:2,自引:1,他引:1  
光子晶体光纤(PCF)和普通光纤的熔接损耗主要来源于两光纤模场直径(MFD)的失配。提出了一种小芯径光子晶体光纤和大模场直径普通光纤低损耗熔接的方法。利用熔融拉锥机加热光子晶体光纤来精确控制光子晶体光纤的空气孔塌缩,以增加光子晶体光纤的模场直径,从而降低其与大模场直径普通光纤的熔接损耗。实现了模场直径为3.94μm的光子晶体光纤和模场直径为10.4μm普通光纤的低损耗熔接,最低损耗小于0.2 dB。  相似文献   

8.
设计了一种新型结构的光子晶体光纤,建立了对应的数学模型并采用全矢量有限元法对该结构的模场强度、有效折射率、双折射、色散特性和限制损耗进行了分析。研究表明,该光纤在1 550nm处可以获得高达7.66×10-3的双折射和低至12ps/(nm·km)的色散值,同时在800~1 600nm波长范围内,始终保持1.498×10-6 dB/m以下的极低限制损耗,可用于制造极低色散值的保偏光纤。  相似文献   

9.
提出了一种新型掺锗芯低弯曲损耗光子晶体光纤。通过调整结构参数,实现了单模低弯曲损耗传输,与标准单模光纤有较好的适配性。仿真结果表明,波长1550nm处,弯曲半径为5mm时,基模损耗为0.014dB/km;弯曲半径为4mm时,基模损耗为0.42dB/km,能承受的弯曲半径小。显示了光子晶体光纤具有成为光纤到户"最后一公里"主要通信介质的性能优势。  相似文献   

10.
为了改善高功率光纤激光器的非线性效应,提出并设计了一种新型的无源、单模、低损耗、大模场的光子晶体光纤结构。利用时域有限差分法并结合完美匹配层边界条件,分析了光子晶体光纤有效模场面积的影响因素,得到光子晶体光纤性能随波长及几何结构的变化规律,从而得到实现更大模场面积的结构参量。结果表明,保证单模传输的情况下,在1.064μm波长处,优化设计的大模场光子晶体光纤有效模场面积可达3118.4μm2,对应的非线性系数可低至5.68×10-5 m-1·W-1,限制损耗可降低到4.55×10-7 dB·m-1。该光纤具备低损耗、低非线性和大模场面积等特性,在实现光子晶体光纤激光器高功率、高光束品质激光输出方面具有重要应用。  相似文献   

11.
全固高非线性低色散斜率光子晶体光纤设计   总被引:1,自引:0,他引:1  
徐惠真  周昌杰 《中国激光》2012,39(11):1106001
提出了利用掺氟同心圆环的光纤结构来提高光子晶体光纤(PCF)的非线性,所需控制的参量仅有两个。设计了三种具有高非线性、低色散斜率和低限制损耗的全固光子晶体光纤。这三种光纤分别具有正常色散、双零色散点和零色散点恰好在1.55 μm波长处的色散曲线特性。所设计的零色散点恰好在1.55 μm波长处的光子晶体光纤色散斜率值为5.12×10-4 ps/(km·nm2),这比传统的高非线性光纤的色散斜率小了2个数量级。同时,该光纤在1.55 μm波长处的非线性系数为31.5 W-1·km-1,限制损耗为9.62×10-5 dB/km。  相似文献   

12.
A new type ultraflattened dispersion square-lattice photonic crystal fiber with two different air-hole diameters in cladding region is proposed and the dispersion is investigated using a compact 2-D finite difference frequency domain method with the anisotropic perfectly matched layers (PML) absorbing boundary conditions. Through numerical simulation and opti- mizing the geometrical parameters, we find that the photonic crystal fibers proposed can realize ultraflattened dispersion of 0±0.06 ps/(km·nm) in wa...  相似文献   

13.
损耗是传统光纤和光子晶体光纤得以实用化的重要参量之一,降低损耗是光子晶体光纤制备的首要问题.折射率引导型光子晶体光纤的损耗由1999年的240 dB/km降至0.28 dB/km(1550 nm波长处),光子带隙型光子晶体光纤的损耗也降低到1.2 dB/km(1620 nm波长处).在对比传统石英光纤损耗来源基础上,阐述了光子晶体光纤的损耗机理,并说明了损耗降低的主要途径.  相似文献   

14.
A new large core (0.5-1.0 mm) graded-index polymer optical fiber was proposed to solve the connection problem of the single-mode silica fiber indoor use for high speed multimedia network. The bending loss for 10-mm bending diameter was dramatically decreased from 20 dB to less than 1 dB by preparing the high numerical aperture graded-index polymer optical fiber. The bandwidth was 585.2 MHz km which was one hundred times larger than that of any existent step-index polymer optical fibers, and the attenuation was 150 dB/km at 650-nm wavelength  相似文献   

15.
Characteristics of dispersion free single-mode fibers in the wavelength regions 1.5 and 1.3 μm are compared experimentally and theoretically. We consider the influence of the refractive index profile on dispersion, the tolerance limits of structure parameters for minimum dispersion, attainable fiber bandwidth, and transmission loss including splicing and bending losses. For a fiber designed for minimum dispersion at 1.5 μm, the measured fiber loss was less than 1 dB/km and bandwidth was 250 GHz. km. nm. The achievable minimum loss estimation shows the advantage of dispersion free fibers at the 1.5 μm wavelength over dispersion free fibers at 1.3 μm.  相似文献   

16.
采用矢量光束传输法(VBPM)对小纤芯光子晶体光纤(PCF)的色散特性进行了数值分析,研究发现通过调节光子晶体光纤的结构参数可以灵活的对其色散补偿值进行调整,能够实现C L波段(1 530~1 565 nm)的宽带色散补偿功能,并且对标准单模光纤的色散斜率有很好的补偿.在∧=1.0μm,d/∧=0.7时,1 550 nm处的色散值可以达到-339.1 ps/(km×nm),相关色散斜率(RDS)可以达到0.003 2 nm-1,能够有效的对标准单模光纤进行色散斜率补偿.  相似文献   

17.
Our recent research on designing microstruc-tured fiber with novel dispersion properties is reported in this paper. Two kinds ofphotonic crystal fibers (PCFs) are introduced first. One is the highly nonlinear PCF with broadband nearly zero flatten dispersion. With introducing the germanium-doped (Ge-doped) core into highly non-linear PCF and optimizing the diameters of the first two inner rings of air holes, a new structure of highly non-linear PCF was designed with the nonlinear coefficient up to 47 W-1·km-1 at the wavelength 1.55 μm and nearly zero flattened dispersion of ±0.5 ps/(km·nm) in telecom-munication window (1460-1625nm). Another is the highly negative PCF with a ring of fluorin-doped (F-doped) rods to form its outer ring core while pure silica rods to form its inner core. The peak dispersion - 1064 ps/(km·nm) in 8 nm full width at half maximum (FWHM) wavelength range and -365ps/(km·nm) in 20nm (FWHM) wavelength range can be reached by adjusting the structure parameters. Then, our recent research on the fabrication of PCFs is reported. Effects of draw parameters such as drawing temperature, feed speed, and furnace temperature on the geometry of the final photonic crystal fiber are investigated.  相似文献   

18.
利用普通熔融拉锥机实现光子晶体光纤拉锥   总被引:2,自引:0,他引:2  
光子晶体光纤的拉锥是实现光子晶体光纤潜在应用价值的重要技术手段。通过优化普通光纤拉锥机的参数,利用"快速低温"拉锥法有效控制了光子晶体光纤空气孔的相对塌缩。实验中实现了两种不同光子晶体光纤的拉锥,光纤外径分别从原来的125μm拉锥到50μm和30μm,光纤的孔直径和孔间距之比基本保持不变,拉锥损耗小于0.4 dB。基于普通熔融拉锥机的光子晶体光纤低损耗拉锥为光纤器件的制作奠定了基础。  相似文献   

19.
A photonic crystal fiber (PCF) can realize a flat dispersion over a wide wavelength range that cannot be realized with a conventional single-mode fiber. However, the confinement loss tends to increase in a conventional dispersion-flattened PCF (DF-PCF) that has uniform air holes. In this paper, a novel PCF that has two cladding layers with different effective indices is proposed. The authors numerically show that the proposed PCF can achieve an ultralow dispersion variation of less than 0.8 ps/nm/spl middot/km in all telecommunication bands, with both a large effective area greater than 100 /spl mu/m/sup 2/ and a low confinement loss less than 0.01 dB/km.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号