首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
本文在蓝宝石衬底上研制了具有高电流增益截止频率(fT)的InAlN/GaN异质结场效应晶体管 (HFETs)。基于MOCVD外延n -GaN欧姆接触工艺实现了器件尺寸的缩小,有效源漏间距(Lsd)缩小至600 nm。此外,采用自对准工艺制备了50 nm直栅。由于器件尺寸的缩小,Vgs= 1 V下器件最大饱和电流(Ids)达到2.11 A/mm,峰值跨导达到609 mS/mm。小信号测试表明,器件fT达到220 GHz、最大振荡频率(fmax)达到48 GHz。据我们所知,该fT值是目前国内InAlN/GaN HFETs器件报道的最高结果。  相似文献   

2.
88 nm栅长fmax=201 GHz InP基In0.53Ga0.47As/In0.52Al0.48As HEMT器件   总被引:1,自引:1,他引:0  
我们成功研制了栅长88 nm, 栅宽2 50 μm, 源漏间距为2.4 μm 的InP基In0.53Ga0.47As/In0.52Al0.48As高电子迁移率器件(HEMT)。栅是使用PMMA/Al/UVⅢ,通过优化电子束曝光时间及其显影时间的方式制作的。这些器件有比较好的直流及其射频特性:峰值跨导、最大源漏饱和电流密度、开启电压、ft和fmax 分别为765 mS/mm, 591 mA/mm, -0.5 V, 150 GHz 和201 GHz。这些器件将非常适合于毫米波段集成电路。  相似文献   

3.
采用二次外延重掺杂n+ GaN实现非合金欧姆接触,并通过优化干法刻蚀和金属有机化学气相沉积(MOCVD)外延工艺,有效降低了欧姆接触电阻.将非合金欧姆接触工艺应用于InAlN/GaN异质结场效应晶体管(HFET)器件制备,器件的有效源漏间距缩小至600 nm.同时,结合40 nm T型栅工艺,制备了高电流截止频率(fT)和最大振荡频率(fmax)的InAlN/GaN HFET器件.结果显示减小欧姆接触电阻和栅长后,器件的电学特性,尤其是射频特性得到大幅提升.栅偏压为0V时,器件最大漏源饱和电流密度达到1.88 A/mm;直流峰值跨导达到681 mS/mm.根据射频小信号测试结果外推得到器件的fT和fmax同为217 GHz.  相似文献   

4.
采用相同的欧姆接触,栅长为100 nm的T型栅以及50 nm的氮化硅(SiN)表面钝化等器件工艺,制备了漏源间距分别为2和3μm的AlGaN/GaN高电子迁移率场效应晶体管(HEMT).研究发现,当漏源间距从2μm增加至3μm后,器件的直流特性略有下降,如在Vgs为1V下的饱和电流密度从1.4 A/mm下降至1.3 A/mm.此外,器件的射频特性也略有下降,电流增益截止频率(fT)从121 GHz降至116 GHz,最大振荡频率(fmax)从201 GHz下降至189 GHz.然而,器件的击穿特性却有显著提升,击穿电压从44 V提升至87 V.在实际器件设计制备过程中可考虑适当增加漏源间距,在保持直流和射频特性的前提下,提升器件的击穿特性.  相似文献   

5.
基于第六代650 V 碳化硅结型肖特基二极管(SiC JBS Diode)和第三代900 V 碳化硅场效应晶体管(SiC MOSFET),开展SiC功率器件的单粒子效应、总剂量效应和位移损伤效应研究。20~80 MeV质子单粒子效应实验中,SiC功率器件发生单粒子烧毁(SEB)时伴随着波浪形脉冲电流的产生,辐照后SEB器件的击穿特性完全丧失。SiC功率器件发生SEB时的累积质子注量随偏置电压的增大而减小。利用计算机辅助设计工具(TCAD)开展SiC MOSFET的单粒子效应仿真,结果表明,重离子从源极入射器件时,具有更短的SEB发生时间和更低的SEB阈值电压。栅-源拐角和衬底-外延层交界处为SiC MOSFET的SEB敏感区域,强电场强度和高电流密度的同时存在导致敏感区域产生过高的晶格温度。SiC MOSFET在栅压偏置(UGS=3 V,UDS=0 V)下开展钴源总剂量效应实验,相比于漏压偏置(UGS=0 V,UDS=300 V)和零压偏置(UGS=UDS=0 V),出现更严重的电学性能退化。利用中带电压法分析发现,栅极偏置下氧化层内的垂直电场提升了陷阱电荷的生成率,加剧了阈值电压的退化。中子位移损伤会导致SiC JBS二极管的正向电流和反向电流减小。在漏极偏置下进行中子位移损伤效应实验,SiC MOSFET的电学性能退化最严重。该研究为空间用SiC器件的辐射效应机理及抗辐射加固研究提供了一定的参考和支撑。  相似文献   

6.
采用再生长n+ GaN非合金欧姆接触工艺研制了具有高电流增益截止频率(fT)的InAlN/GaN异质结场效应晶体管 (HFETs),器件尺寸得到有效缩小,源漏间距减小至600 nm.通过优化干法刻蚀和n+ GaN外延工艺,欧姆接触总电阻值达到0.16 Ω·mm,该值为目前金属有机化学气相沉积(MOCVD)方法制备的最低值.采用自对准电子束曝光工艺实现34 nm直栅.器件尺寸的缩小以及欧姆接触的改善,器件电学特性,尤其是射频特性得到大幅提升.器件的开态电阻(Ron)仅为0.41 Ω·mm,栅压1 V下,漏源饱和电流达到2.14 A/mm.此外,器件的电流增益截止频率(fT)达到350 GHz,该值为目前GaN基HFET器件国内报道最高值.  相似文献   

7.
在SiC衬底上制备得到了表面钝化氮化硅(SiN)的AlGaN/Ga N高电子迁移率场效应晶体管(HEMTs)。采用高电子浓度的AlGaN/GaN异质结材料、90 nm T型栅、100 nm SiN表面钝化、低欧姆接触以及较短漏源间距等方法来提升器件性能。在Vgs=4 V时器件的最大漏源饱和电流密度为1.72 A/mm,最大跨导为305 m S/mm,此结果为国内报道的AlGaN/GaN HEMT器件最大漏源饱和电流密度。此外,栅长为90 nm T型栅器件的电流增益截止频率(fT)为109GHz,最大振荡频率(fmax)为144 GHz。  相似文献   

8.
研究了一款高性能的AlGaN/GaN高电子迁移率晶体管器件(HEMT),器件基于在蓝宝石衬底上外延生长的AlGaN/GaN异质结构HEMT材料,器件栅长为86 nm,源漏间距为0.8μm。电子束光刻实现T型栅和源漏,保证了器件小的栅长和高的对准精度。制备的器件显示了良好的直流特性和射频特性,在栅偏压为0 V时漏电流密度为995 mA/mm,在栅源电压Vgs为-4.5 V时,最大峰值跨导为225 mS/mm;器件的电流增益截止频率fT和最大振荡频率fmax分别为102和147 GHz。高fT值一方面得益于小栅长,另一方面由于小源漏间距减小了源漏沟道电阻。  相似文献   

9.
J. Ajayan  D. Nirmal 《半导体学报》2017,38(4):044001-6
In this work, the performance of Lg=22 nm In0.75Ga0.25As channel-based high electron mobility transistor (HEMT) on InP substrate is compared with metamorphic high electron mobility transistor (MHEMT) on GaAs substrate. The devices features heavily doped In0.6Ga0.4As source/drain (S/D) regions, Si double δ-doping planar sheets on either side of the In0.75Ga0.25As channel layer to enhance the transconductance, and buried Pt metal gate technology for reducing short channel effects. The TCAD simulation results show that the InP HEMT performance is superior to GaAs MHEMT in terms of fT, fmax and transconductance (gm_max). The 22 nm InP HEMT shows an fT of 733 GHz and an fmax of 1340 GHz where as in GaAs MHEMT it is 644 GHz and 924 GHz, respectively. InGaAs channel-based HEMTs on InP/GaAs substrates are suitable for future sub-millimeter and millimeter wave applications.  相似文献   

10.
研制了高电流增益截止频率(fT)的InAlN/GaN高电子迁移率晶体管(HEMT).采用金属有机化学气相沉积(MOCVD)再生长n+GaN非合金欧姆接触工艺将器件源漏间距缩小至600 nm,降低了源、漏寄生电阻,有利于改善器件的寄生效应;使用低压化学气相沉积(LPCVD)生长SiN作为栅下介质,降低了InAlN/GaN HEMT栅漏电;利用电子束光刻实现了栅长为50 nm的T型栅.此外,还讨论了寄生效应对器件fT的影响.测试结果表明,器件的栅漏电为3.8 μA/mm,饱和电流密度为2.5 A/mm,fT达到236 GHz.延时分析表明,器件的寄生延时为0.13 ps,在总延时中所占的比例为19%,优于合金欧姆接触工艺的结果.  相似文献   

11.
The influence of the width of the quantum well L and doping on the band structure, scattering, and electron mobility in nanoheterostructures with an isomorphic In0.52Al0.48As/In0.53Ga0.47As/In0.52Al0.48As quantum well grown on an InP substrate are investigated. The quantum and transport mobilities of electrons in the dimensionally quantized subbands are determined using Shubnikov-de Haas effect measurements. These mobilities are also calculated for the case of ionized-impurity scattering taking into account intersub-band electron transitions. It is shown that ionized-impurity scattering is the dominant mechanism of electron scattering. At temperatures T < 170 K, persistent photoconductivity is observed, which is explained by the spatial separation of photoexcited charge carriers.  相似文献   

12.
The influence of the design of the metamorphic buffer of In0.7Al0.3As/In0.75Ga0.25As metamorphic nanoheterostructures for high-electron-mobility transistors (HEMTs) on their electrical parameters and photoluminescence properties is studied experimentally. The heterostructures are grown by molecular-beam epitaxy on GaAs (100) substrates with linear or step-graded In x Al1 ? x As metamorphic buffers. For the samples with a linear metamorphic buffer, strain-compensated superlattices or inverse steps are incorporated into the buffer. At photon energies ?ω in the range 0.6–0.8 eV, the photoluminescence spectra of all of the samples are identical and correspond to transitions from the first and second electron subbands to the heavy-hole band in the In0.75Ga0.25As/In0.7Al0.3As quantum well. It is found that the full width at half-maximum of the corresponding peak is proportional to the two-dimensional electron concentration and the luminescence intensity increases with increasing Hall mobility in the heterostructures. At photon energies ?ω in the range 0.8–1.3 eV corresponding to the recombination of charge carriers in the InAlAs barrier region, some features are observed in the photoluminescence spectra. These features are due to the difference between the indium profiles in the smoothing and lower barrier layers of the samples. In turn, the difference arises from the different designs of the metamorphic buffer.  相似文献   

13.
120 nm gate-length In_(0.7)Ga_(0.3)As/In_(0.52)Al_(0.48) As InP-based high electron mobility transitions(HEMTs) are fabricated by a new T-shaped gate electron beam lithograph(EBL) technology,which is achieved by the use of a PMMA/PMGI/ZEP520/PMGI four-layer photoresistor stack.These devices also demonstrate excellent DC and RF characteristics:the transconductance,maximum saturation drain-to-source current,threshold voltage,maximum current gain frequency,and maximum power-gain cutoff frequency of InGaAs/I...  相似文献   

14.
This paper proposes a In/sub 0.5/Al/sub 0.5/As/In/sub x/Ga/sub 1-x/As/In/sub 0.5/Al/sub 0.5/As (x=0.3-0.5-0.3) metamorphic high-electron mobility transistor with tensile-strained channel. The tensile-strained channel structure exhibits significant improvements in dc and RF characteristics, including extrinsic transconductance, current driving capability, thermal stability, unity-gain cutoff frequency, maximum oscillation frequency, output power, power gain, and power added efficiency.  相似文献   

15.
通过合理的外延层材料结构设计和改进的器件制备工艺,制备出功率增益截止频率(fmax)为183GHz的晶格匹配InP基In0.53Ga0.47As-In0.52Al0.48As HEMT。该fmax为国内HEMT器件最高值,还报道了器件的结构、制备工艺以及器件的直流和高频特性。  相似文献   

16.
The first room-temperature operation of Ga0.47In0.53As/Al0.48In0.52As resonant tunnelling (RT) diodes is reported. The peak/valley ratio of the current is as high as 4:1 at room temperature and is 15:1 at 80 K. These are the highest values of peak/valley ratio at the respective temperatures, reported so far, in this material system. The position of the peak in the current/voltage characteristic also showed good agreement with that obtained from an electron tunnelling transmission calculation.  相似文献   

17.
通过合理的外延层材料结构设计和改进的器件制备工艺,制备出功率增益截止频率(fmax)为183GHz的晶格匹配InP基In0.53Ga0.47As-In0.52Al0.48As HEMT.该fmax为国内HEMT器件最高值.还报道了器件的结构、制备工艺以及器件的直流和高频特性.  相似文献   

18.
A drastic decrease in the sheet carrier concentration of modulation-doped Al0.48In0.52As/Ga0.47In0.53As/InP heterostructures has been observed after O2 plasma treatment followed by thermal treatment up to 350°C. The decrease in sheet carrier concentration, which is speculated to be caused by both plasma damage and impurities penetrating from the surface of the epilayer, can be suppressed substantially by using PH3 plasma treatment prior to the O2 plasma and thermal treatments.  相似文献   

19.
The results of studies of the surface morphology, electrical parameters, and photoluminescence properties of In0.38Al0.62As/In0.38Ga0.62As/In0.38Al0.62As metamorphic nanoheterostructures on GaAs substrates are reported. Some micron-sized defects oriented along the [011] and \([0\bar 11]\) directions and corresponding to regions of outcropping of stacking faults are detected on the surface of some heterostructures. The Hall mobility and optical properties of the samples correlate with the surface defect density. In the photoluminescence spectra, four emission bands corresponding to the recombination of charge carriers in the InGaAs quantum well (1–1.2 eV), the InAlAs metamorphic buffer (1.8–1.9 eV), the GaAs/AlGaAs superlattice at the buffer-substrate interface, and the GaAs substrate are detected. On the basis of experimentally recorded spectra and self-consistent calculations of the band diagram of the structures, the compositions of the alloy constituents of the heterostructures are established and the technological variations in the compositions in the series of samples are determined.  相似文献   

20.
提出了利用分子束外延方法生长In0.5Ga0.5As/In0.5Al0.5As应变耦合量子点,并分析量子点的形貌和光学性质随GaAs隔离层厚度变化的特点.实验结果表明,随着耦合量子点中的GaAs隔离层厚度从2 nm增加到10 nm,In0.5Ga0.5As量子点的密度增大、均匀性提高,Al原子扩散和浸润层对量子点PL谱的影响被消除,而且InAlAs材料的宽禁带特征使其成为InGaAs量子点红外探测器中的暗电流阻挡层.由此可见,选择合适的GaAs隔离层厚度形成InGaAs/InAlAs应变耦合量子点将有益于InGaAs量子点红外探测器的研究.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号