Ta/Au ohmic contacts to n-type ZnO

Ta/Au ohmic contacts are fabricated on n-type ZnO (∼1 × 10¹⁷ cm⁻³) epilayers, which were grown on R-plane sapphire substrates by metal organic chemical vapor deposition (MOCVD). After growth and metallization, the samples are annealed at 300°C and 500°C for 30 sec in nitrogen ambient. The specific contact resistance is measured to be 3.2×10⁻⁴ Ωcm² for the as-deposited samples. It reduces to 5.4×10⁻⁶ Ωcm² after annealing at 300°C for 30 sec without significant surface morphology degradation. When the sample is annealed at 500°C for 30 sec, the specific contact resistance increases to 3.3 × 10⁻⁵ Ωcm². The layer structures no longer exist due to strong Au and Ta in-diffusion and O out-diffusion. The contact surface becomes rough and textured.     

Vanadium-based ohmic contacts to n-type Al<Subscript>0.6</Subscript>Ga<Subscript>0.4</Subscript>N

Four vanadium-based contacts to n-type Al_0.6Ga_0.4N were compared in this work. Both V/Al/Pd/Au and V/Al/V/Au contacts with optimized layer thicknesses provided lower specific-contact resistances than did the previously reported V/Al/Pt/Au ohmic contact. Specific contact resistances of the V/Al/Pd/Au (15 nm/85 nm/20 nm/95 nm) and V/Al/V/Au (15 nm/85 nm/20 nm/95 nm) contacts were 3×10⁻⁶ Ω·cm² and 4×10⁻⁶ Ω·cm², respectively. On the other hand, an analogous V/Al/Mo/Au contact never became ohmic, even after it was annealed at 900°C for 30 sec. Compared to the V/Al/Pd/Au contact, the V/Al/V/Au contact required a less severe annealing condition (30 sec at 700°C instead of 850°C). The V/Al/V/Au contact also provided a smoother surface, with a root-mean-square (RMS) roughness of 39 nm.     

Simultaneous formation of p- and n-type ohmic contacts to 4H-SiC using the ternary Ni/Ti/Al system

Fabrication procedures for silicon carbide power metal oxide semiconductor field effect transistors (MOSFETs) can be improved through simultaneous formation (i.e., same contact materials and one step annealing) of ohmic contacts on both the p-well and n-source regions. We have succeeded with the simultaneous formation of the ohmic contacts for p- and n-type SiC semiconductors by examining ternary Ni/Ti/Al materials with various compositions, where a slash symbol “/” indicates the deposition sequence starting with Ni. The Ni(20 nm)/Ti(50 nm)/Al(50 nm) combination provided specific contact resistances of 2 × 10⁻³ Ω-cm² and 2 × 10⁻⁴ Ω-cm² for p- and n-type SiC, respectively, after annealing at 800°C for 30 min, where the doping level of Al in the SiC substrate was 4.5 × 10¹⁸ cm⁻³ and the level of N was 1.0 × 10¹⁹ cm⁻³.     

Thermally stable Ge/Cu/Ti ohmic contacts to n-type GaN

The performance of a novel Ge/Cu/Ti metallization scheme on n-type GaN has been investigated for obtaining thermally and electrically stable low-resistance ohmic contacts. Isochronal (2 min.) anneals in the 600–740°C temperature range and isothermal (690°C) anneals for 2–10 min. duration were performed in inert atmosphere. For the 690°C isothermal schedule, ohmic behavior was observed after annealing for 3 min. or longer with a lowest contact resistivity of 9.1 × 10⁻⁵ Ωcm² after the 10 min. anneal for a net donor doping concentration of 9.2 × 10¹⁷ cm^−Ω3. Mean roughness (R_a) for anneals at 690°C was almost constant at around 5 nm, up to an annealing duration of 10 min., which indicates a good thermal stability of the contact scheme.     

Low resistance bilayer Nd/Al ohmic contacts on n-type GaN

A bilayer Nd/Al metallization structure has been deposited onto low pressure organometallic vapor phase epitaxy grown n-type GaN ( 1 × 10¹⁸ cm⁻³) by electron-beam evaporation. Ohmic metal contacts were patterned photolithographically for standard transmission line measurement, and then thermally annealed at temperatures ranging from 200 to 350°C and from 500 to 650°C using conventional thermal annealing (CTA) and rapid thermal annealing (RTA), respectively. The lowest values for the specify contact resistivity of 9.8 × 10⁻⁶ Ω−cm² and 8 × 10⁻⁶ Ω−cm² were obtained using Nd/Al metallization with CTA of 250°C for 5 min and RTA of 600°C for 30 s. Examination of the surface morphology using atomic force microscopy as a function of annealing temperature revealed that the surface roughness was strongly influenced by conventional thermal annealing, it was smooth in the temperature range from 550 to 650°C for rapid thermal annealing. Auger electron spectroscopy depth profiling was employed to investigate the metallurgy and interdiffusion of contact formation.     

InGaN/GaN LEDs with a Si-doped InGaN/GaN short-period superlattice tunneling contact layer

Nitride-based light-emitting diodes (LEDs) with Si-doped n⁺-In_0.23Ga_0.77N/GaN short-period superlattice (SPS) tunneling contact top layer were fabricated. It was found that although the measured specific-contact resistance is around 1 × 10⁻² Ω-cm² for samples with an SPS tunneling contact layer, the measured specific-contact resistance is around 1.5×10⁰ Ω-cm² for samples without an SPS tunneling contact layer. Furthermore, it was found that one could lower the LED-operation voltage from 3.75 V to 3.4 V by introducing the SPS structure. It was also found that the LED-operation voltage is almost independent of the CP₂Mg flow rate when we grow the underneath p-type GaN layer. The LED-output intensity was also found to be larger for samples with the SPS structure.     

A technique to reduce the contact resistance to 4H-silicon carbide using germanium implantation

The effects of implanted Ge on the resistance of nickel-metal contacts to n-type and p-type 4H-SiC are reported. The Ge was implanted with an energy of 346 keV and a dose of 1.7×10¹⁶ cm⁻², and the wafer was annealed up to 1700°C for 30 min. Contact resistance measurements using the transfer length method (TLM) were performed on etched mesas of n-type and p-type 4H-SiC, with and without the Ge. For the annealed-Ni metal contacts, the Ge lowered the specific contact resistivity from 5.3×10⁻⁴ Ωcm² to 6.0×10⁻⁵ Ωcm² for n-type SiC and from 1.2×10⁻³ Ωcm² to 8.3×10⁻⁵ Ωcm² for p-type SiC. For the as-deposited (unannealed) Ni, the Ge produced ohmic contacts, whereas the contacts without Ge were rectifying. These results suggest that the addition of Ge can be an important process step to reduce the contact resistance for SiC-device applications.     

Study of contact resistivity, mechanical integrity, and thermal stability of Ti/Al and Ta/Al ohmic contacts to n-type GaN

The annealing conditions and contact resistivities of Ta/Al ohmic contacts to n-type GaN are reported for the first time. The high temperature stability and mechanical integrity of Ti/Al and Ta/Al contacts have been investigated. Ta/Al (35 nm/115 nm) contacts to n-type GaN became ohmic after annealing for 3 min at 500°C or for 15 s at 600°C. A minimum contact resistivity of 5×10⁻⁶Ω cm² was measured after contacts were repatterned with an Al layer to reduce the effect of a high metal sheet resistance. Ti/Al and Ta/Al contacts encapsulated under vacuum in quartz tubes showed a significant increase in contact resistivity after aging for five days at 600°C. Cross section transmission electron microscopy micrographs and electrical measurements of aged samples indicate that the increased contact resistivity is primarily the result of degradation of the metal layers. Minimal reactions at the metal/GaN interface of aged samples were observed.     

High-resistivity GaSb bulk crystals grown by the vertical bridgman method

Heavily compensated GaSb (2-in.-diameter substrates) with resistivity as high as 7 × 10³ Ω-cm, corresponding to a net donor concentration of 3.5×10¹³ cm⁻³ at 77 K, and 16.4 Ω-cm, corresponding to net donor concentration of 1.16×10¹⁶ cm⁻³ at 300 K, have been obtained by tellurium (Te) compensation in vertical-Bridgman-grown bulk crystals. Very interesting p- to n-type as well as n- to p-type changes have been observed as a function of temperature in these samples.     

Indium-tin oxide/Si contacts with In- and Sn-diffusion barriers in polycrystalline Si thin-film transistor liquid-crystal displays

Indium and tin were used as the diffusion barrier between indium-tin oxide (ITO) and polycrystalline-silicon layers to reduce the contact resistance. The ITO/Si contacts may be adopted in thin-film transistor liquid-crystal displays (TFT-LCD) to reduce the number of fabrication steps. With In and Sn layers, contact-resistance values of 5 × 10⁻³−4×10⁻³ Ωcm² were obtained. These values were higher than those of the conventional ITO/Mo/Al/Si contacts (3×10⁻⁵−4 × 10⁻⁴ Ωcm²) but lower than the values obtained from ITO/Si contacts (about 1×10⁻² Ωcm²). The Sn was stable after annealing, but In diffused into Si and lost its function as the diffusion barrier.     

Properties of electrical contacts on bulk and epitaxial n-type ZnO

The electrical properties of several metal contacts to n-type ZnO (0001) were studied. The ZnO samples consisted of bulk single-crystal material, epitaxial layers on sapphire grown by molecular beam epitaxy (MBE), and polycrystalline thin films on sapphire obtained by pulsed laser deposition (PLD). Ohmic and rectifying contacts were observed dependent upon both the metal material and the ZnO surface. Ohmic contacts were characterized using the circular transmission line method (c-TLM), where contact resistivity was found to be in the range of 10⁻⁴−10⁻⁵ Ω-cm². Schottky behavior was observed using Ag contacts exhibiting varying leakage current and breakdown voltage dependent on the polarity of the ZnO surface.     

Low resistance pd/ge ohmic contacts to epitaxially lifted-off n-type GaAs film

A low resistance PdGe nonalloyed ohmic contact has been successfully formed to epitaxially lifted-off n-type GaAs films. The contact is made by lifting off partially metallized n-type GaAs films using the epitaxial lift-off method and bonding them to metallized Si substrates by natural intermolecular Van Der Waals forces. Low temperature sintering (200°C) of this contact results in metallurgical bonding and formation of the ohmic contact. We have measured specific contact resistances of 5 × 10⁻⁵ Ω-cm₂ which is almost half the value obtained for pure Pd contacts. Germanium forms a degenerately doped heterojunction interfacial layer to GaAs. Our experimental results show that germanium diffuses to the interface and acts as a dopant layer to n-GaAs film surface. Therefore, for epitaxially lifted-off n-type GaAs films, PdGe is a low resistance ohmic metal contact to use.     

Electrical and structural properties of low-resistance Ti/Al/Re/Au ohmic contacts to n-type GaN

Titanium (15 nm)/aluminum (60 nm)/rhenium (20 nm)/gold (50 nm) ohmic contacts to moderately doped n-type GaN (4.07×10¹⁸ cm⁻³) have been investigated as a function of annealing temperature. It is shown that the current-voltage (I–V) characteristics of the contacts are improved upon annealing at temperatures in the range of 550–750°C. Specific contact resistance as low as 1.3 × 10⁻⁶ Ωcm² is obtained after annealing at 750°C for 1 min in a nitrogen ambient. X-ray photoemission spectroscopy (XPS) results show that the Ga 2p core level for the sample annealed at 750°C shifts toward the high binding side by 0.71 eV compared with that of the as-deposited one. It is also shown that the contact does not seriously suffer from thermal degradation even when annealed at 750°C for 30 min. Based on Auger electron spectroscopy (AES), glancing angle x-ray diffraction (GXRD), and XPS results, possible explanations for the annealing-induced improvement of the ohmic behavior are described and discussed.     

Effects of annealing on the thermoelectric and microstructural properties of deformed n-type Bi2Te3-based compounds

We studied the effects of deformation and annealing of n-type 90Bi₂Te₃-5Sb₂Te₃-5Sb₂Se₃ thermoelectric compound. Hot-extrusion was conducted to prepare the deformed compound and then this compound was annealed at 400°C for 1–24 hr. When the undoped cast-ingot was extruded, the compound was changed from p-type to n-type due to the electrons generated during the extrusion process. For the compound extruded with SbI₃-doped powders, the thermoelectric properties were also varied for the extrusion process. After annealing at 400°C more than 9 hr, the powder-extruded compound was recrystallized. This caused a decrease in carrier concentration and crystallographic anisotropy. In case of the compound extruded at the ratio of 10:1, the Seebeck coefficient α and the electrical resistivity ρ increased due to recrystallization. However, thermal conductivity κ of the compound decreased. This resulted in an increase in the figure-of-merit from 1.23 × 10⁻³ to 1.63 × 10⁻³ K⁻¹.     

Electrical transport properties of single GaN and InN nanowires

The transport properties of single GaN and InN nanowires grown by thermal catalytic chemical vapor deposition were measured as a function of temperature, annealing condition (for GaN) and length/square of radius ratio (for InN). The as-grown GaN nanowires were insulating and exhibited n-type conductivity (n ≈ 2×10¹⁷ cm⁻³, mobility of 30 cm²/V s) after annealing at 700°C. A simple fabrication process for GaN nanowire field-effect transistors on Si substrates was employed to measure the temperature dependence of resistance. The transport was dominated by tunneling in these annealed nanowires. InN nanowires showed resistivity on the order of 4×10⁻⁴ Ω cm and the specific contact resistivity for unalloyed Pd/Ti/Pt/Au ohmic contacts was near 1.09×10⁻⁷ Ω cm². For In N nanowires with diameters <100 nm, the total resistance did not increase linearly with length/square of radius ratio but decreased exponentially, presumably due to more pronounced surface effect. The temperature dependence of resistance showed a positive temperature coefficient and a functional form characteristic of metallic conduction in the InN nanowires.     

Improved ohmic contact to n-type 4H and 6H-SiC using nichrome

Results are reported for ohmic contacts formed on n-type 4H and 6H-SiC using nichrome (80/20 weight percent Ni/Cr). The electrical characteristics of these NiCr contacts are similar to those of contacts formed on 6H-SiC using pure Ni (∼1×10⁻⁵Ω-cm² for moderately doped material), but the contacts exhibit significant improvement with regard to physical stability. Composite Au/NiCr contacts exhibit good stability during long-term anneals (∼2500 h) at 300°C without the requirement of a diffusion barrier layer between the NiCr ohmic contact layer and the Au cap layer. In addition, the use of NiCr results in success rates near 100% for direct wire bonding to the Au cap layers. Characterization of the contacts by Auger electron spectroscopy, Rutherford backscattering spectroscopy, and transmission electron microscopy provides an explanation for the observed behavior.     

P- and N-type doping of GaN and AlGaN epitaxial layers grown by metalorganic chemical vapor deposition

Mg- and Si-doped GaN and AlGaN films were grown by metalorganic chemical vapor deposition and characterized by room-temperature photoluminescence and Hall-effect measurements. We show that the p-type carrier concentration resulting from Mg incorporation in GaN:Mg films exhibits a nonlinear dependence both on growth temperature and growth pressure. For GaN and AlGaN, n-type doping due to Si incorporation was found to be a linear function of the silane molar flow. Mg-doped GaN layers with 300K hole concentrations p ∼2×10¹⁸ cm⁻³ and Si-doped GaN films with electron concentrations n∼1×10¹⁹ cm⁻³ have been grown. N-type Al_0.10Ga_0.90N:Si films with resistivities as low as p ∼6.6×10⁻³ Ω-cm have been measured.     

Low-resistance and thermally stable Pd/Ru ohmic contacts to p-type GaN

We report on low-resistance and thermally stable Pd/Ru ohmic contacts to surface-treated p-GaN (3 × 10¹⁷ cm⁻³). It is shown that annealing at 500°C for 2 min in a N₂ ambient improves ohmic contact properties. Specific contact resistance is measured to be 9.2(±0.2) × 10⁻⁴ and 2.4(±0.2) × 10⁻⁵ Ωcm² for the as-deposited and annealed samples, respectively. Atomic force microscopy results show that the surfaces of both the contacts are remarkably smooth with a root-mean-square (rms) roughness of about 0.6 nm. The current-voltage-temperature (I-V-T) and calculation results indicate that, for the as-deposited contact, thermionic field emission is dominant, while for the annealed contact, field emission dominates the current flow.     

Ohmic contact formation on inductively coupled plasma etched 4H-silicon carbide

We report on the investigation of ohmic contact formation using sputtered titanium-tungsten contacts on an inductively coupled plasma (ICP) etch-damaged 4H-SiC surface. Transfer length method (TLM) measurements were performed to characterize how ICP-etch damage affects the performance of ohmic contacts to silicon carbide. In order to recover etch damage, high-temperature oxidation (1250°C for 1 h) was evaluated for one of the samples. Some of the etch damage was recovered, but it did not fully recover the etch damage for the sample etched with medium platen power (60 W). From our TLM measurements, the specific contact resistance (ρ _C of sputtered titanium tungsten on highly doped n⁺-type 4H-SiC epilayers with a doping of 1.1×10¹⁹ cm⁻³ for the unetched reference sample, 30-W etched, and 60-W etched with and without sacrificial oxidation was as low as 3.8×10⁻⁵ Ωcm², 3.3×10⁻⁵ Ωcm², 2.3×10⁻⁴ Ωcm², and 1.3×10⁻³ Ωcm², respectively. We found that the low-power (30 W) ICP-etching process did not affect the formation of ohmic contacts, and we did not observe any difference between the unetched and the 30-W etched sample from our TLM measurements, having the same value of the ρ _C. However, medium-platen-power (60 W) ICP etching showed significant influence on the ohmic contact formation. We found that the specific contact resistance is highly related to the surface roughness and quality of the metals, and the lower, specific contact resistance is due to smoother and denser ohmic contacts.     

Growth and doping of SiC-thin films on low-stress,amorphous Si<Subscript>3</Subscript>N<Subscript>4</Subscript>/Si substrates for robust microelectromechanical systems applications

The N₂-doped 3C-SiC thin films have been grown by low-pressure, chemical vapor deposition (LPCVD) on amorphous Si₃N₄/p-Si (111) substrates using the single, organosilane-precursor trimethylsilane [(CH₃)₃SiH]. The effects of N₂ flow rate and growth temperature on the electrical properties of SiC films were investigated by Hall-effect measurements. The electron-carrier concentration is between 10¹⁷–10¹⁸/cm³. The lowest resistivities at 400 K and 300 K are 1.12×10⁻² and 1.18×10⁻¹ cm, respectively. The corresponding sheet resistances are 75.02 Ω/□ and 790.36 Ω/□. The SiC film structure was studied by x-ray diffraction. The 3C-SiC films oriented in the 〈111〉 direction with a 2ϑ peak at 35.5° and line widths between 0.18–0.25° were obtained. The SiC/Si₃N₄ interface is very smooth and free of voids. The fabrication of microelectromechanical (MEMS) structures incorporating the SiC films is discussed.