High‐Mobility Carriers in Germanene Derivatives

Buckled elemental analogs of graphene—2D‐Xenes silicene, germanene, and stanene—and their derivatives are predicted to host high‐mobility carriers. Experiments, however, have not as yet confirmed the predictions. Here, high‐mobility (exceeding 10⁴ cm² V^?1 s^?1) carriers are discovered in intercalated multilayer germanene. Epitaxial films of antiferromagnetic and diamagnetic MGe₂ are synthesized via topochemical reactions, followed by extensive studies of the atomic and magnetic structures. Quantum oscillations in MGe₂ resistance manifest quasi‐2D Fermi‐surface pockets with effective masses of carriers as low as 0.015 m_e, comparable to graphene. The detected signature of the chiral anomaly in magnetoresistance and nonzero Berry phases may indicate the topological nature of the MGe₂ electronic structure and charge transport. The discovery bridges the gap between theory and experiment, thus establishing 2D‐Xenes as promising building blocks in materials engineering. Concurrently, the combination of magnetism and high mobility in Eu‐intercalated germanene is attractive for spintronic applications.     

Highly Elastic and Conductive N‐Doped Monolithic Graphene Aerogels for Multifunctional Applications

The simple synthesis of ultralow‐density (≈2.32 mg cm^?3) 3D reduced graphene oxide (rGO) aerogels that exhibit high electrical conductivity and excellent compressibility are described herein. Aerogels are synthesized using a combined hydrothermal and thermal annealing method in which hexamethylenetetramine is employed as a reducer, nitrogen source, and graphene dispersion stabilizer. The N‐binding configurations of rGO aerogels increase dramatically, as evidenced by the change in pyridinic‐N/quaternary‐N ratio. The conductivity of this graphene aerogel is ≈11.74 S m^?1 at zero strain, whereas the conductivity at a compressive strain of ≈80% is ≈704.23 S m^?1, which is the largest electrical conductivity reported so far in any 3D sponge‐like low‐density carbon material. In addition, the aerogel has excellent hydrophobicity (with a water contact angle of 137.4°) as well as selective absorption for organic solvents and oils. The compressive modulus (94.5 kPa; ρ ≈ 2.32 mg cm^?3) of the rGO aerogel is higher than that of other carbon‐based aerogels. The physical and chemical properties (such as high conductivity, elasticity, high surface area, open pore structure, and chemical stability) of the aerogel suggest that it is a viable candidate for the use in energy storage, electrodes for fuel cells, photocatalysis, environmental protection, energy absorption, and sensing applications.     

High Mobility WS2 Transistors Realized by Multilayer Graphene Electrodes and Application to High Responsivity Flexible Photodetectors

The electrical contact is one of the main issues preventing semiconducting 2D materials to fulfill their potential in electronic and optoelectronic devices. To overcome this problem, a new approach is developed here that uses chemical vapor deposition grown multilayer graphene (MLG) sheets as flexible electrodes for WS₂ field‐effect transistors. The gate‐tunable Fermi level, van der Waals interaction with the WS₂, and the high electrical conductivity of MLG significantly improve the overall performance of the devices. The carrier mobility of single‐layer WS₂ increases about a tenfold (50 cm² V^?1 s^?1 at room temperature) by replacing conventional Ti/Au metal electrodes (5 cm² V^?1 s^?1) with the MLG electrodes. Further, by replacing the conventional SiO₂ substrate with a thin (1 µm) parylene‐C flexible film as insulator, flexible WS₂ photodetectors that are able to sustain multiple bending stress tests without significant performance degradation are realized. The flexible photodetectors exhibited extraordinarily high gate‐tunable photoresponsivities, reaching values of 4500 A W^?1, and with very short (<2 ms) response time. The work of the heterostacked structure combining WS₂, graphene, and the very thin polymer film will find applications in various flexible electronics, such as wearable high‐performance optoelectronics devices.     

Amorphous Boron Nitride: A Universal,Ultrathin Dielectric For 2D Nanoelectronics

Next‐generation nanoelectronics based on 2D materials ideally will require reliable, flexible, transparent, and versatile dielectrics for transistor gate barriers, environmental passivation layers, capacitor spacers, and other device elements. Ultrathin amorphous boron nitride of thicknesses from 2 to 17 nm, described in this work, may offer these attributes, as the material is demonstrated to be universal in structure and stoichiometric chemistry on numerous substrates including flexible polydimethylsiloxane, amorphous silicon dioxide, crystalline Al₂O₃, other 2D materials including graphene, 2D MoS₂, and conducting metals and metal foils. The versatile, large area pulsed laser deposition growth technique is performed at temperatures less than 200 °C and without modifying processing conditions, allowing for seamless integration into 2D device architectures. A device‐scale dielectric constant of 5.9 ± 0.65 at 1 kHz, breakdown voltage of 9.8 ± 1.0 MV cm^?1, and bandgap of 4.5 eV were measured for various thicknesses of the ultrathin a‐BN material, representing values higher than previously reported chemical vapor deposited h‐BN and nearing single crystal h‐BN.     

Phthalocyanine‐Based 2D Conjugated Metal‐Organic Framework Nanosheets for High‐Performance Micro‐Supercapacitors

2D conjugated metal‐organic frameworks (2D c‐MOFs) are emerging as a novel class of conductive redox‐active materials for electrochemical energy storage. However, developing 2D c‐MOFs as flexible thin‐film electrodes have been largely limited, due to the lack of capability of solution‐processing and integration into nanodevices arising from the rigid powder samples by solvothermal synthesis. Here, the synthesis of phthalocyanine‐based 2D c‐MOF (Ni₂[CuPc(NH)₈]) nanosheets through ball milling mechanical exfoliation method are reported. The nanosheets feature with average lateral size of ≈160 nm and mean thickness of ≈7 nm (≈10 layers), and exhibit high crystallinity and chemical stability as well as a p‐type semiconducting behavior with mobility of ≈1.5 cm² V^?1 s^?1 at room temperature. Benefiting from the ultrathin feature, the nanosheets allow high utilization of active sites and facile solution‐processability. Thus, micro‐supercapacitor (MSC) devices are fabricated mixing Ni₂[CuPc(NH)₈] nanosheets with exfoliated graphene, which display outstanding cycling stability and a high areal capacitance up to 18.9 mF cm^?2; the performance surpasses most of the reported conducting polymers‐based and 2D materials‐based MSCs.     

Flexible transparent conductive film based on silver nanowires and reduced graphene oxide

Silver nanowires (AgNWs) with diameter of 90—150 nm and length of 20—50 μm were successfully synthesized by a polyol process. Graphene oxide (GO) was prepared by Hummers method, and was reduced with strong hydrazine hy-drate at room temperature. The flexible transparent conductive films (TCFs) were fabricated using the mixed cellulose eater (MCE) as matrix and AgNWs and reduced graphene oxide (rGO) as conductive fillers by the improved vacuum fil-tration process. Then, the optical, electrical and mechanical properties of the AgNWs-rGO films were investigated. The results show that for the AgNWs-rGO film produced with the deposition densities of AgNWs and rGO as 110 mg·m-2 and 55 mg·m-2, the optical transmission at 550 nm is 88.4% with Rs around 891 Ω·sq-1, whereas the optical transmission for the AgNWs-rGO film with deposition densities of AgNWs and rGO of 385 mg·m-2 and 55 mg·m-2 is 79.0% at 550 nm with Rs around 9.6 Ω·sq-1. There is little overt increase in Rs of the AgNWS-rGO film after tape tests for 200 times. The bending test results indicate that the change in Rs of AgNWs-MCE film is less than 2% even after 200 cycles of compressive or tensile bending. The excellent mechanical properties of the AgNWs-rGO film can be attributed to the burying of AgNWs and rGO at the surface of MCE     

Direct Graphene Transfer and Its Application to Transfer Printing Using Mechanically Controlled,Large Area Graphene/Copper Freestanding Layer

Direct graphene transfer is an attractive candidate to prevent graphene damage, which is a critical problem of the conventional wet transfer method. Direct graphene transfer can fabricate the transferred graphene film with fewer defects by using a polymeric carrier. Here a unique direct transfer method is proposed using a 300 nm thick copper carrier as a suspended film and a transfer printing process by using the polydimethylsiloxane (PDMS) stamp under controlled peeling rate and modulus. Single and multilayer graphene are transferred to flat and curved PDMS target substrate directly. With the transfer printing process, the transfer yield of a trilayer graphene with 1000 µm s^?1 peeling rate is 68.6% of that with 1 µm s^?1 peeling rate. It is revealed that the graphene transfer yield is highly related to the storage modulus of the PDMS stamp: graphene transfer yield decreases when the storage modulus of the PDMS stamp is lower than a specific threshold value. The relationship between the graphene transfer yield and the interfacial shear strain of the PDMS stamp is studied by finite‐element method simulation and digital image correlation.     

Stress Controllability in Thermal and Electrical Conductivity of 3D Elastic Graphene‐Crosslinked Carbon Nanotube Sponge/Polyimide Nanocomposite

Stress controllability in thermal and electrical conductivity is important for flexible piezoresistive devices. Due to the strength‐elasticity trade‐off, comprehensive investigation of stress‐controllable conduction in elastic high‐modulus polymers is challenging. Here presented is a 3D elastic graphene‐crosslinked carbon nanotube sponge/polyimide (G_w‐CNT/PI) nanocomposite. Graphene welding at the junction enables both phonon and electron transfer as well as avoids interfacial slippage during cyclic compression. The uniform G_w‐CNT/PI comprising a high‐modulus PI deposited on a porous templated network combines stress‐controllable thermal/electrical conductivity and cyclic elastic deformation. The uniform composites show different variation trends controlled by the porosity due to different phonon and electron conduction mechanisms. A relatively high k (3.24 W m^?1 K^?1, 1620% higher than PI) and suitable compressibility (16.5% under 1 MPa compression) enables the application of the composite in flexible elastic thermal interface conductors, which is further analyzed by finite element simulations. The interconnected network favors a high stress‐sensitive electrical conductivity (sensitivity, 973% at 9.6% strain). Thus, the G_w‐CNT/PI composite can be an important candidate material for piezoresistive sensors upon porosity optimization based on stress‐controllable thermal or electrical conductivity. The results provide insights toward controlling the stress‐induced thermal/electrical conductivities of 3D interconnected templated composite networks for piezoresistive conductors or sensors.     

Highly Conductive and Environmentally Stable Organic Transparent Electrodes Laminated with Graphene

Improving the lifetime and the operational and thermal stability of organic thin‐film materials while maintaining high conductivity and mechanical flexibility is critical for flexible electronics applications. Here, it is reported that highly conductive and environmentally stable organic transparent electrodes (TEs) can be fabricated by mechanically laminating poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) films containing dimethylsulfoxide and Zonyl fluorosurfactant (PDZ films) with a monolayer graphene barrier. The proposed lamination process allows graphene to be coated onto the PDZ films uniformly and conformally with tight interfacial binding, free of wrinkles and air gaps. The laminated films exhibit an outstanding room‐temperature hole mobility of ≈85.1 cm² V^?1 s^?1 since the graphene can serve as an effective bypass for charge carriers. The significantly improved stability of the graphene‐laminated TEs against high mechanical/thermal stress, humidity, and ultraviolet irradiation is particularly promising. Furthermore, the incorporation of the graphene barrier increases the expected lifetime of the TEs by more than two orders of magnitude.     

Flexible All‐Solid‐State Supercapacitors of High Areal Capacitance Enabled by Porous Graphite Foams with Diverging Microtubes

The practical applications of wearable electronics rely on the successful development of flexible and integrable energy devices with small footprints. This work reports a completely new type of graphite foam made of strategically created superstructures with covalently attached diverging microtubes, and their applications as electrode supports for binder‐free and additive‐free flexible supercapacitors. Because of the enhanced volumetric surface areas compared to conventional graphite foams, a high loading of pseudocapacitive materials (Mn₃O₄, 3.91 mg cm^?2, 78 wt%) is achieved. The supercapacitors provide areal capacitances as high as 820 mF cm^?2 at 1 mV s^?1, while still maintaining high rate capability and 88% retention of capacitance after 3000 continuous charging and discharging cycles. When assembled as all‐solid‐state flexible symmetric supercapacitors, they offer one of the highest full‐cell capacitances (191 mF cm^?2) among similar manganese oxide/graphene foams, and retain 80% capacitance after 1000 mechanical cycles. The potential of such flexible supercapacitors is also manifested by directly powering electric nanomotors that can trace along letters “U” and T,” which is the first demonstration of flexible supercapacitors for wireless/portable nanomanipulation systems. This work could inspire a new paradigm in designing and creating 3D porous micro/nanosuperstructures for an array of self‐powered electronic and nanomechanical applications.     

Ambient‐Dried Cellulose Nanofibril Aerogel Membranes with High Tensile Strength and Their Use for Aerosol Collection and Templates for Transparent,Flexible Devices

The application potential of cellulose nanofibril (CNF) aerogels has been hindered by the slow and costly freeze‐ or supercritical drying methods. Here, CNF aerogel membranes with attractive mechanical, optical, and gas transport properties are prepared in ambient conditions with a facile and scalable process. Aqueous CNF dispersions are vacuum‐filtered and solvent exchanged to 2‐propanol and further to octane, followed by ambient drying. The resulting CNF aerogel membranes are characterized by high transparency (>90% transmittance), stiffness (6 GPa Young's modulus, 10 GPa cm³ g^?1 specific modulus), strength (97 MPa tensile strength, 161 MPa m³ kg^?1 specific strength), mesoporosity (pore diameter 10–30 nm, 208 m² g^?1 specific surface area), and low density (≈0.6 g cm^?3). They are gas permeable thus enabling collection of nanoparticles (for example, single‐walled carbon nanotubes, SWNT) from aerosols under pressure gradients. The membranes with deposited SWNT can be further compacted to transparent, conductive, and flexible conducting films (90% specular transmittance at 550 nm and 300 Ω ?^{? 1} sheet resistance with AuCl₃‐salt doping). Overall, the developed aerogel membranes pave way toward use in gas filtration and transparent, flexible devices.     

Flexible MXene/Graphene Films for Ultrafast Supercapacitors with Outstanding Volumetric Capacitance

A strategy to prepare flexible and conductive MXene/graphene (reduced graphene oxide, rGO) supercapacitor electrodes by using electrostatic self‐assembly between positively charged rGO modified with poly(diallyldimethylammonium chloride) and negatively charged titanium carbide MXene nanosheets is presented. After electrostatic assembly, rGO nanosheets are inserted in‐between MXene layers. As a result, the self‐restacking of MXene nanosheets is effectively prevented, leading to a considerably increased interlayer spacing. Accelerated diffusion of electrolyte ions enables more electroactive sites to become accessible. The freestanding MXene/rGO‐5 wt% electrode displays a volumetric capacitance of 1040 F cm^?3 at a scan rate of 2 mV s^?1 , an impressive rate capability with 61% capacitance retention at 1 V s^?1 and long cycle life. Moreover, the fabricated binder‐free symmetric supercapacitor shows an ultrahigh volumetric energy density of 32.6 Wh L^?1, which is among the highest values reported for carbon and MXene based materials in aqueous electrolytes. This work provides fundamental insight into the effect of interlayer spacing on the electrochemical performance of 2D hybrid materials and sheds light on the design of next‐generation flexible, portable and highly integrated supercapacitors with high volumetric and rate performances.     

Flexible Solid‐State Supercapacitors with Enhanced Performance from Hierarchically Graphene Nanocomposite Electrodes and Ionic Liquid Incorporated Gel Polymer Electrolyte

High energy density, durability, and flexibility of supercapacitors are required urgently for the next generation of wearable and portable electronic devices. Herein, a novel strategy is introduced to boost the energy density of flexible soild‐state supercapacitors via rational design of hierarchically graphene nanocomposite (GNC) electrode material and employing an ionic liquid gel polymer electrolyte. The hierarchical graphene nanocomposite consisting of graphene and polyaniline‐derived carbon is synthesized as an electrode material via a scalable process. The meso/microporous graphene nanocomposites exhibit a high specific capacitance of 176 F g^?1 at 0.5 A g^?1 in the ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIBF₄) with a wide voltage window of 3.5 V, good rate capability of 80.7% in the range of 0.5–10 A g^?1 and excellent stability over 10 000 cycles, which is attributed to the superior conductivity (7246 S m^?1), and quite large specific surface area (2416 m² g^?1) as well as hierarchical meso/micropores distribution of the electrode materials. Furthermore, flexible solid‐state supercapacitor devices based on the GNC electrodes and gel polymer electrolyte film are assembled, which offer high specific capacitance of 180 F g^?1 at 1 A g^?1, large energy density of 75 Wh Kg^?1, and remarkable flexible performance under consecutive bending conditions.     

3D Macroscopic Architectures from Self‐Assembled MXene Hydrogels

Assembly of 2D MXene sheets into a 3D macroscopic architecture is highly desirable to overcome the severe restacking problem of 2D MXene sheets and develop MXene‐based functional materials. However, unlike graphene, 3D MXene macroassembly directly from the individual 2D sheets is hard to achieve for the intrinsic property of MXene. Here a new gelation method is reported to prepare a 3D structured hydrogel from 2D MXene sheets that is assisted by graphene oxide and a suitable reductant. As a supercapacitor electrode, the hydrogel delivers a superb capacitance up to 370 F g^?1 at 5 A g^?1, and more promisingly, demonstrates an exceptionally high rate performance with the capacitance of 165 F g^?1 even at 1000 A g^?1. Moreover, using controllable drying processes, MXene hydrogels are transformed into different monoliths with structures ranging from a loosely organized porous aerogel to a dense solid. As a result, a 3D porous MXene aerogel shows excellent adsorption capacity to simultaneously remove various classes of organic liquids and heavy metal ions while the dense solid has excellent mechanical performance with a high Young's modulus and hardness.     

2D Boron Sheets: Structure,Growth, and Electronic and Thermal Transport Properties

The structures of boron clusters, such as flat clusters and fullerenes, resemble those of carbon. Various two‐dimensional (2D) borophenes have been proposed since the production of graphene. The recent successful fabrication of borophene sheets has prompted extensive researches, and some unique properties are revealed. In this review, the recent theoretical and experimental progress on the structure, growth, and electronic and thermal transport properties of borophene sheets is summarized. The history of prediction of boron sheet structures is introduced. Existing with a mixture of triangle lattice and hexagonal lattice, the structures of boron sheets have peculiar characteristics of polymorphism and show significant dependence on the substrate. Due to the unique structure and complex B? B bonds, borophene sheets have many interesting electronic and thermal transport properties, such as strong nonlinear effect, strong thermal transport anisotropy, high thermal conductance in the ballistic transport and low thermal conductivity in the diffusive transport. The growth mechanism and synthesis of borophene sheets on different metal substrates are also presented. The successful prediction and synthesis will shed light on the exploration of new novel materials. Besides, the outstanding and peculiar properties of borophene make them tempting platform for exploring novel physical phenomena and extensive applications.     

Fiber Reinforced Layered Dielectric Nanocomposite

Polymer dielectrics find applications in modern electronic and electrical technologies due to their low density, durability, high dielectric breakdown strength, and design flexibility. However, they are not reliable at high temperatures due to their low mechanical integrity and thermal stability. Herein, a self‐assembled dielectric nanocomposite is reported, which integrates 1D polyaramid nanofibers and 2D boron nitride nanosheets through a vacuum‐assisted layer‐by‐layer infiltration process. The resulting nanocomposite exhibits hierarchical stacking between the 2D nanosheets and 1D nanofibers. Specifically, the 2D nanosheets provide a thermally conductive network while the 1D nanofibers provide mechanical flexibility and robustness through entangled nanofiber–nanosheet morphologies. Experiments and density functional theory show that the nanocomposites through thickness heat transfer processes are nearly identical to that of boron nitride due to synergistic stacking of polyaramid units onto boron nitride nanosheets through van der Waals interactions. The nanocomposite sheets outperform conventional dielectric polymers in terms of mechanical properties (about 4–20‐fold increase of stiffness), light weight (density ≈1.01 g cm^?3), dielectric stability over a broad range of temperature (25–200 °C) and frequencies (10³–10⁶ Hz), good dielectric breakdown strength (≈292 MV m^?1), and excellent thermal management capability (about 5–24 times higher thermal conductivity) such as fast heat dissipation.     

Hydrophilic Nanotube Supported Graphene–Water Dispersible Carbon Superstructure with Excellent Conductivity

In this work, it is shown that the hydrophilic functionalized multiwall carbon nanotubes (MWCNs) can stabilize a large amount of pristine graphene nanosheets in pure water without the assistance of surfactants, ionic liquids, or hydrophilic polymers. Role of stabilizer is conveyed by highly hydrophilic carbon nanotubes, functionalized by dihydroxy phenyl groups, affording a stable dispersion at concentrations as high as 15 mg mL^?1. Such multidimensional (2D/1D) graphene/MWCN hybrid is found to be dispersible also in other polar organic solvents such as ethanol, isopropanol, N,N‐dimethylformamide, ethylene glycol, and their mixtures. High‐resolution transmission microscopy and atomic force microscopy (AFM) including a liquid mode AFM manifest several types of interaction including trapping of multiwalled carbon nanotubes between the graphene sheets or the modification of graphene edges. Molecular dynamic simulations show that formation of an assembly is kinetically controlled. Importantly, the hybrid can be deposited on the paper by drop casting or dispersed in water‐soluble polymers resulting in record values of electrical conductivity (sheet resistance up to R_s ≈ 25 Ω sq^?1 for free hybrid material and R_s ≈ 1300 Ω sq^?1 for a polyvinilalcohol/hybrid composite film). Thus, these novel water dispersible carbon superstructures reveal a high application potential as conductive inks for inkjet printing or as highly conductive polymers.     

Hierarchical Graphene–Carbon Fiber Composite Paper as a Flexible Lateral Heat Spreader

As a low dimensional crystal, graphene attracts great attention as heat dissipation material due to its unique thermal transfer property exceeding the limit of bulk graphite. In this contribution, flexible graphene–carbon fiber composite paper is fabricated by depositing graphene oxide into the carbon fiber precursor followed by carbonization. In this full‐carbon architecture, scaffold of one‐dimensional carbon fiber is employed as the structural component to reinforce the mechanical strength, while the hierarchically arranged two‐dimensional graphene in the framework provides a convenient pathway for in‐plane acoustic phonon transmission. The as‐obtained hierarchical carbon/carbon composite paper possesses ultra‐high in‐plane thermal conductivity of 977 W m^?1 K^?1 and favorable tensile strength of 15.3 MPa. The combined mechanical and thermal performances make the material highly desirable as lateral heat spreader for next‐generation commercial portable electronics.     

Liquid‐Gated Transistors Based on Reduced Graphene Oxide for Flexible and Wearable Electronics

Graphene is regarded as the ultimate material for future flexible, high‐performance, and wearable electronics. Herein, a novel, robust, all‐green, highly reliable (yield ≥ 99%), and upscalable technology is reported for wearable applications comprising reduced graphene oxide (rGO) as the electroactive component in liquid‐gated transistors (LGTs). rGO is a formidable material for future flexible and wearable applications due to its easy processability, excellent surface reactivity, and large‐area coverage. A novel protocol is established toward the high‐yield fabrication of flexible rGO LGTs combining high robustness (>1.5 h of continuous operation) with state‐of‐the‐art performances, being similar to those of their rigid counterparts operated under liquid gating, including field‐effect mobility of ≈10^?1 cm² V^?1 s^?1 and transconductance of ≈25 µS. Permeable membranes have been proven crucial to operate flexible LGTs under mechanical stress with reduced amounts of solution (<20 µL). Our rGO LGTs are operated in artificial sweat exploiting two different layouts based on lateral‐flow paper fluidics. These approaches pave the road toward future real‐time tracking of perspiration via a simple and cost‐effective approach. The reported findings contribute to the robust and scalable production of novel graphene‐based flexible devices, whose features fulfill the requirements of wearable electronics.     

Growth of Vertically Aligned Tunable Polyaniline on Graphene/ZrO2 Nanocomposites for Supercapacitor Energy‐Storage Application

In‐situ hydrothermal method is employed to synthesize graphene/zirconium oxide composite from respective precursors graphene oxide and zirconium oxy‐nitrate. In this method, the graphene oxide is reduced itself to graphene and simultaneously metal oxide gets anchor on the graphene sheets. A novel method is also developed for the preparation of vertically aligned tunable polyaniline on the graphene/zirconium oxide nanocomposite, which leads to achieve high surface area (207.1 m² g^?1), high electrical conductivity (70.8 S cm^?1), high specific capacitance (1359.99 Fg^?1 at 1 mV s^?1), and high electrochemical performances as supercapacitor electrode materials. This vertically aligned conducting polymer gets easy contact with electrolyte ions and provides numerous redox active sites during charging and discharging. Moreover, such a simple and low cost assembly approach can be a pioneer for the large‐scale production of various functional architectures for energy storage and conversions.