首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
唐健  王晓亮  肖红领 《半导体学报》2014,35(11):113006-5
A novel In Ga N back barrier high electron mobility transistors structure with a compositionally stepgraded Al Ga N barrier layer was grown by metal organic chemical vapor deposition on sapphire substrate.The structural and electrical properties of two samples were investigated and compared:the first sample is the stepgraded structure and the second one is the high Al structure as a comparison.By calculating full width at half maximum of XRD measurements,the densities of screw-type threading dislocations are 8.34108cm2and11.44108cm2 for step-graded structure and high Al structure,respectively,which are consistent with the results of atomic force microscopy.By Hall measurements,the measured two-dimensional electron gas mobility was 1820 cm2/(V s) for step-graded structure,and 1300 cm2/(V s) for high Al structure,respectively.The stepgraded structure improves the crystal quality of Al Ga N layer due to the released lattice strain.The device was fabricated and leakage current is only 28 A when the drain voltage is 10 V; it was found that the In Ga N back barrier could effectively reduce the buffer leakage current.  相似文献   

2.
The influence of annealed ohmic contact metals on the electron mobility of a two dimensional electron gas (2DEG) is investigated on ungated AlGaN/GaN heterostructures and AlGaN/GaN heterostructure field effect transistors (AlGaN/GaN HFETs). Current-voltage (I-V) characteristics for ungated AlGaN/GaN heterostructures and capacitance-voltage (C-V) characteristics for AlGaN/GaN HFETs are obtained, and the electron mobility for the ungated AlGaN/GaN heterostructure is calculated. It is found that the electron mobility of the 2DEG for the ungated AlGaN/GaN heterostructure is decreased by more than 50% compared with the electron mobility of Hall measurements. We propose that defects are introduced into the AlGaN barrier layer and the strain of the AlGaN barrier layer is changed during the annealing process of the source and drain, causing the decrease in the electron mobility.  相似文献   

3.
Abstract: We propose a new structure of InxAll-xN/GaN high electron mobility transistor (HEMT) with gate length of 20 nm. The threshold voltage of this HEMT is achieved as -0.472 V. In this device the InA1N barrier layer is intentionally n-doped to boost the ION/IOFF ratio. The InAlN layer acts as donor barrier layer for this HEMT which exhibits an ION = 10-4.3 A and a very low IOFF = 10-14.4 A resulting in an ION/IoFF ratio of 1010.1. We compared our obtained results with the conventional InAlN/GaN HEMT device having undoped barrier and found that the proposed device has almost l0s times better ION/IOFF ratio. Further, the mobility analysis in GaN channel of this proposed HEMT structure along with DC analysis, C-V and conductance characteristics by using small-signal analysis are also presented in this paper. Moreover, the shifts in threshold voltage by DIBL effect and gate leakage current in the proposed HEMT are also discussed. InAlN was chosen as the most preferred barrier layer as a replacement of AlGaN for its excellent thermal conductivity and very good scalability.  相似文献   

4.
Effects of the ZnO buffer layer and Al proportion on AZO film properties   总被引:1,自引:0,他引:1  
To evaluate the influence of the ZnO buffer layer and Al proportion on the properties of ZnO: Al (AZO)/ZnO bi-layer films, a series of AZO/ZnO films are deposited on the quartz substrates by electron beam evaporation. The X-ray diffraction measurement shows that the crystal quality of the films is improved with the increase of the film thickness. The electrical properties of the films are investigated. The carrier concentration and Hall mobility both increase with the increase of buffer layer thickness. However, the resistivity reaches the lowest at about 50 nm-thick buffer layer. The lowest resistivity and the maximum Hall mobility are both obtained at 1 wt% Al concentration. But the optical transmittance of all the films is greater than 80% regardless of the buffer layer thickness with Al concentration lower than 5 wt% in the visible region.  相似文献   

5.
正The fabrication of AlGaN/GaN double-channel high electron mobility transistors on sapphire substrates is reported.Two carrier channels are formed in an AlGaN/GaN/AlGaN/GaN multilayer structure.The DC performance of the resulting double-channel HEMT shows a wider high transconductance region compared with single-channel HEMT. Simulations provide an explanation for the influence of the double-channel on the high transconductance region.The buffer trap is suggested to be related to the wide region of high transconductance.The RF characteristics are also studied.  相似文献   

6.
The correlation between the resistivity of an undoped GaN/Al2O3 interfacial layer and in-situ reflectance spectrum in metalorganic chemical vapor deposition and the mechanism of this correlation were investigated. The first minimum reflectance during the initial high-temperature GaN growth was found to be a good indicator of the resistivity of the GaN buffer. The background electron concentration and mobility were both higher in the samples with higher indicative reflectance at that point. The resistivity of the GaN buffer layer was predominantly determined by an ∼0.25-μm-thick layer near the GaN/Al2O3 interface. Atomic force microscope (AFM) and high-resolution x-ray diffraction (HRXRD) results showed that the samples with higher indicative reflectance had smaller sized but higher density nuclei before the high-temperature GaN growth and lower screw threading dislocation (TD) density in the initially grown GaN. The difference in the background electron concentration and mobility of the interfacial layer was related to the relatively higher concentration of the O and Al diffused from Al2O3, which is also dependent on the size and density of the nuclei. These differences were found not to affect the structural and electrical properties or the surface morphology of AlGaN/GaN high electron-mobility transistors (HEMTs, except for the buffer conduction) when the GaN buffer is thick enough (e.g., ∼2.5 μm).  相似文献   

7.
Current collapses were studied,which were observed in AlGaN/GaN high electron mobility transistors(HEMTs) with and without InGaN back barrier(BB) as a result of short-term bias stress.More serious drain current collapses were observed in InGaN BB AlGaN/GaN HEMTs compared with the traditional HEMTs.The results indicate that the defects and surface states induced by the InGaN BB layer may enhance the current collapse.The surface states may be the primary mechanism of the origination of current collapse in AlGaN/GaN HEMTs for short-term direct current stress.  相似文献   

8.
段焕涛  郝跃  张进城 《半导体学报》2009,30(10):105002-3
Nucleation layer formation is a key factor for high quality gallium nitride(GaN)growth on a sapphire substrate.We found that the growth rate substantially affected the nucleation layer morphology,thereby having a great impact on the crystal quality,surface morphology and electrical properties of AlGaN/GaN heterostructures on sapphire substrates.A nucleation layer with a low growth rate of 2.5 nm/min is larger and has better coalescence than one grown at a high growth rate of 5 nm/min.AlGaN/GaN heterostructures on a nucleation layer with low growth rate have better crystal quality,surface morphology and electrical properties.  相似文献   

9.
The effect of active layer deposition temperature on the electrical performance of amorphous InGaZnO (a-IGZO) thin film transistors (TFTs) is investigated. With increasing annealing temperature, TFT performance is firstly improved and then degraded generally. Here TFTs with best performance defined as "optimized-annealed" are selected to study the effect of active layer deposition temperature. The field effect mobility reaches maximum at deposition temperature of 150℃ while the room-temperature fabricated device shows the best subthreshold swing and off-current. From Hall measurement results, the carrier concentration is much higher for intentional heated a-IGZO films, which may account for the high off-current in the corresponding TFT devices. XPS characterization results also reveal that deposition temperature affects the atomic ratio and Ols spectra apparently. Importantly, the variation of field effect mobility of a-IGZO TFTs with deposition temperature does not coincide with the tendencies in Hall mobility of a-IGZO thin films, Based on the further analysis of the experimental results on a-IGZO thin films and the corresponding TFT devices, the trap states at front channel interface rather than IGZO bulk layer properties may be mainly responsible for the variations of field effect mobility and subthreshold swing with IGZO deposition temperature.  相似文献   

10.
Nonpolar (1120) a-plane GaN films have been grown by low-pressure metal-organic vapor deposition on r-plane (1102) sapphire substrate. The structural and electrical properties of the a-plane GaN films are investigated by high-resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM) and van der Pauw Hall measurement. It is found that the Hall voltage shows more anisotropy than that of the c-plane samples; furthermore, the mobility changes with the degree of the van der Pauw square diagonal to the c direction, which shows significant electrical anisotropy. Further research indicates that electron mobility is strongly influenced by edge dislocations.  相似文献   

11.
DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.  相似文献   

12.
This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel's.  相似文献   

13.
The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.  相似文献   

14.
Today, micro-system technology and the development of new MEMS (Micro-Electro-Mechanical Systems) are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.  相似文献   

15.
The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.  相似文献   

16.
From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.  相似文献   

17.
Waveguide multilayer optical card (WMOC) is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling & processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic (VB) language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.  相似文献   

18.
It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output(MIMO) communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.  相似文献   

19.
The effect of laser microbeam trapping the bioparticles has been appfied widely in the biology .However the micromechanism of the acting that realizes the laser-microbeam trapping bioparticles is still lacking. In this paper ,the act microchenism of the gradiant force of laser microbeam for the bioparticles is analysed by means of quantum theory ,The result accords with our experiment.  相似文献   

20.
Due to variable symbol length of digital pulse interval modulation(DPIM), it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation(FDPIM) method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号