Planar n-on-p ion milled mid-wavelength and long-wavelength infrared diodes on molecular beam epitaxy vacancy-doped CdHgTe on CdZnTe

Planar mid-wavelength infrared (MWIR) and long-wavelength infrared (LWIR) photodiodes were fabricated by ion milling molecular beam epitaxy (MBE) Cd_xHg_1−xTe (CMT) layers with and without compositional grading in the layer. Linear arrays with 32 and 64 diodes, as well as test diodes of varying size, were fabricated. Good quantum efficiencies were measured, and MWIR diodes, with cutoff wavelength λ_CO=4.5 μm, had zero-bias resistance-area values (R₀A) in excess of 1×10⁷ Ωcm², whereas LWIR diodes with λ_CO=8.9−9.3 μm had R₀A=3×10² Ωcm² at 77 K. Comparison between a limited number of layers indicates that in layers with a gradient the RA values are a factor of ∼10 larger, and possibly more uniform, than in layers without a gradient.     

HgCdTe/Si materials for long wavelength infrared detectors

The heteroepitaxial growth of HgCdTe on large-area Si substrates is an enabling technology leading to the production of low-cost, large-format infrared focal plane arrays (FPAs). This approach will allow HgCdTe FPA technology to be scaled beyond the limitations of bulk CdZnTe substrates. We have already achieved excellent mid-wavelength infrared (MWIR) and short wavelength infrared (SWIR) detector and FPA results using HgCdTe grown on 4-in. Si substrates using molecular beam epitaxy (MBE), and this work was focused on extending these results into the long wavelength infrared (LWIR) spectral regime. A series of nine p-on-n LWIR HgCdTe double-layer heterojunction (DLHJ) detector structures were grown on 4-in. Si substrates. The HgCdTe composition uniformity was very good over the entire 4-in. wafer with a typical maximum nonuniformity of 2.2% at the very edge of the wafer; run-to-run composition reproducibility, realized with real-time feedback control using spectroscopic ellipsometry, was also very good. Both secondary ion mass spectrometry (SIMS) and Hall-effect measurements showed well-behaved doping and majority carrier properties, respectively. Preliminary detector results were promising for this initial work and good broad-band spectral response was demonstrated; 61% quantum efficiency was measured, which is very good compared to a maximum allowed value of 70% for a non-antireflection-coated Si surface. The R₀A products for HgCdTe/Si detectors in the 9.6-μm and 12-μm cutoff range were at least one order of magnitude below typical results for detectors fabricated on bulk CdZnTe substrates. This lower performance was attributed to an elevated dislocation density, which is in the mid-10⁶ cm⁻² range. The dislocation density in HgCdTe/Si needs to be reduced to <10⁶ cm⁻² to make high-performance LWIR detectors, and multiple approaches are being tried across the infrared community to achieve this result because the technological payoff is significant.     

Ten-inch molecular beam epitaxy production system for HgCdTe growth

Growth of Hg_1−xCd_xTe by molecular beam epitaxy (MBE) has been under development since the early 1980s at Rockwell Scientific Company (RSC), formerly the Rockwell Science Center; and we have shown that high-performance and highly reproducible MBE HgCdTe double heterostructure planar p-on-n devices can be produced with high throughput for various single- and multiplecolor infrared applications. In this paper, we present data on Hg_1−xCd_xTe epitaxial layers grown in a ten-inch production MBE system. For growth of HgCdTe, standard effusion cells containing CdTe and Te were used, in addition to a Hg source. The system is equipped with reflection high energy electron diffraction (RHEED) and spectral ellipsometry in addition to other fully automated electrical and optical monitoring systems. The HgCdTe heterostructures grown in our large ten-inch Riber 49 MBE system have outstanding structural characteristics with etch-pit densities (EPDs) in the low 10⁴ cm⁻² range, Hall carrier concentration in low 10¹⁴ cm⁻³, and void density <1000 cm². The epilayers were grown on near lattice-matched (211)B Cd_0.96Zn_0.04Te substrates. High-performance mid wavelength infrared (MWIR) devices were fabricated with R₀A values of 7.2×10⁶ Ω-cm² at 110 K, and the quantum efficiency without an antireflection coating was 71.5% for cutoff wavelength of 5.21 μm at 37 K. For short wavelength infrared (SWIR) devices, an R₀A value of 9.4×10⁵ Ω-cm² at 200 K was obtained and quantum efficiency without an antireflection coating was 64% for cutoff wavelength of 2.61 μm at 37 K. These R₀A values are comparable to our trend line values in this temperature range.     

High purity InxGa1−xSb single crystals with cutoff wavelength of 7–8 µm grown by melt epitaxy

For the first time, InGaSb single crystals with a cutoff wavelength of 7–8 μm were successfully grown on GaAs substrates by a new growth technique named melt epitaxy. The band gap of InGaSb layers obviously narrowed compared with those with the same compositions grown by ordinary methods and the longest cutoff wavelength reached 8.3 μm. High electron mobility of 8.05×10⁴ cm²/Vs and low carrier density of 1×10¹⁵ cm⁻³ at 77 K were obtained indicating high purity of InGaSb epilayers.     

MBE P-on-n Hg1−xCdxTe heterostructure detectors on silicon substrates

The capability of growing state-of-the-art middle wavelength infrared (MWIR)-HgCdTe layers by molecular beam epitaxy (MBE) on large area silicon substrates has been demonstrated. We have obtained excellent compositional uniformity with standard deviation of 0.001 with mean composition of 0.321 across 1.5″ radii. R₀A as high as 5 × 10⁷ ω-cm² with a mean value of 7 × 10⁶ Θ-cm² was measured for cut-off wavelength of 4.8 μm at 77K. Devices exhibit diffusion limited performance for temperatures above 95K. Quantum efficiencies up to 63% were observed (with no anti-reflection coating) for cut-off wavelength (4.8–5.4) μm @ 77K. Excellent performance of the fabricated photodiodes on MBE HgCdTe/CdTe/Si reflects on the overall quality of the grown material in the MWIR region.     

Imaging one-dimensional and two-dimensional planar photodiode detectors fabricated by ion milling molecular beam epitaxy CdHgTe

Imaging one-dimensional (1-D) and two-dimensional (2-D) arrays of mid-wavelength infrared (MWIR) and long-wavelength infrared (LWIR) planar photodiodes were fabricated by ion milling of vacancy-doped molecular beam epitaxy Cd_xHg_1−xTe layers. Sixty-four-element 1-D arrays of 26×26 μm² or 26×56 μm² diodes were processed. Zero-bias resistance-area values (R₀A) at 77 K of 4×10⁶ Θcm² at cutoff wavelength λ_CO=4.5 μm were measured, as well as high quantum efficiencies. To avoid creating a leakage current during ball bonding to the 1-D array diodes, a ZnS layer was deposited on top of the CdTe passivation layer, as well as extra electroplated Au on the bonding pads. The best measured noise equivalent temperature difference (NETD) on a LWIR array was 8 mK, with a median of 14 mK for the 42 operable diodes. The best measured NETD on a MWIR array was 18 mK. Two-D arrays showed reasonably good uniformity of R₀A and zero-bias current (I₀) values. The first 64×64 element 2-D array of 16×16 μm² MWIR diodes has been hybridized to read-out electronics and gave median NETD of 60 mK.     

Heteroepitaxy of HgCdTe(112) infrared detector structures on Si(112) substrates by molecular-beam epitaxy

High-quality, single-crystal epitaxial films of CdTe(112)B and HgCdTe(112)B have been grown directly on Si(112) substrates without the need for GaAs interfacial layers. The CdTe and HgCdTe films have been characterized with optical microscopy, x-ray diffraction, wet chemical defect etching, and secondary ion mass spectrometry. HgCdTe/Si infrared detectors have also been fabricated and tested. The CdTe(112)B films are highly specular, twin-free, and have x-ray rocking curves as narrow as 72 arc-sec and near-surface etch pit density (EPD) of 2 × 10⁶ cm⁻² for 8 μm thick films. HgCdTe(112)B films deposited on Si substrates have x-ray rocking curve FWHM as low as 76 arc-sec and EPD of 3-22 × 10⁶ cm⁻². These MBE-grown epitaxial structures have been used to fabricate the first high-performance HgCdTe IR detectors grown directly on Si without use of an intermediate GaAs buffer layer. HgCdTe/Si infrared detectors have been fabricated with 40% quantum efficiency and R₀A = 1.64 × 10⁴ Ωm₂ (0 FOV) for devices with 7.8 μm cutoff wavelength at 78Kto demonstrate the capability of MBE for growth of large-area HgCdTe arrays on Si.     

MWIR DLPH HgCdTe photodiode performance dependence on substrate material

Mid wavelength infrared p-on-n double layer planar heterostructure (DLPH) photodiodes have been fabricated in HgCdTe double layers grown in situ by liquid phase epitaxy (LPE), on CdZnTe and for the first time on CdTe/sapphire (PACE-1). Characterization of these devices shed light on the nature of the material limits on device performance for devices performing near theoretical limits. LPE double layers on CdZnTe and on PACE-1 substrates were grown in a horizontal slider furnace. All the photodiodes are p-on-n heterostructures with indium as the n-type dopant and arsenic the p-type dopant. Incorporation of arsenic is via implantation followed by an annealing step that was the same for all the devices fabricated. The devices are passivated with MBE CdTe. Photodiodes have been characterized as a function of temperature. R₀A_imp values obtained between 300 and 78K are comparable for the two substrates and are approximately a factor of five below theoretical values calculated from measured material parameters. The data, for the PACE-1 substrate, indicates diffusion limited performance down to 110K. Area dependence gives further indications as to the origin of diffusion currents. Comparable R₀A_imp for various diode sizes indicates a p-side origin. R₀A and optical characteristics for the photodiodes grown on lattice-matched CdZnTe substrates and lattice mismatched PACE-1 are comparable. Howover, differences were observed in the noise characteristics of the photodiodes. Noise was measured on 50 × 50 μm devices held under a 100 mV reverse bias. At 110K, noise spectrum for devices from the two substrates is in the low 10⁻¹⁵ A/Hz^1/2 range. This value reflects the Johnson noise of the room temperature 10¹⁰ Ω feedback resistor in the current amplifier that limits the minimum measurable noise. Noise at 1 Hz, −100 mV and 120K for the 4.95 μm PACE-1 devices is in the 1–2 × 10⁻¹⁴ A/Hz^1/2, a factor of 5–10 lower than previously grown typical PACE-1 n⁺-on-p layers. Noise at 120K for the 4.60 μm PACE-1 and LPE on CdZnTe was again below the measurement technique limit. Greatest distinction in the noise characteristics for the different substrates was observed at 163K. No excess low frequency noise was observed for devices fabricated on layers grown by LPE on lattice-matched CdZnTe substrates. Photodiode noise measured at 1Hz, −100 mV and 163K in the 4.60 μm PACE-1 layer is in the 1–2×10⁻¹³ A/Hz^1/2, again a factor of 5–10 lower than previously grown PACE-1 n⁺-on-p layers. More variation in noise (4×10⁻¹³−2×10⁻¹² A/Hz^1/2) was observed for devices in the 4.95 μm PACE-1 layer. DLPH devices fabricated in HgCdTe layers grown by LPE on lattice-matched CdZnTe and on lattice-mismatched PACE-1 have comparable R₀A and quantum efficiency values. The distinguishing feature is that the noise is greater for devices fabricated in the layer grown on lattice mismatched substrates, suggesting dislocations inherent in lattice mismatched material affects excess low frequency noise but not zero bias impedance.     

HgCdZnTe quaternary materials for lattice-matched two-color detectors

As the number of bands and the complexity of HgCdTe multicolor structures increases, it is desirable to minimize the lattice mismatch at growth interfaces within the device structure in order to reduce or eliminate mismatch dislocations at these interfaces and potential threading dislocations that can degrade device performance. To achieve this we are investigating the use of Hg_1−x−yCd_xZn_yTe quaternary alloys which have an independently tunable lattice constant and bandgap. Lattice matching in Hg_1−x−yCd_xZn_yTe structures can be achieved using small additions of Zn (y<0.015) to HgCdTe ternary alloys. We have investigated some of the basic properties of Hg_1−x−yCd_xZn_yTe materials with x≈0.31 and 0≤y≤0.015. The quaternary layers were grown on (112)CdZnTe substrates using MBE and the amount of Zn in the layers was determined from calibrated SIMS measurements. As expected, the lattice constant decreased and the bandgap increased as Zn was added to HgCdTe to form Hg_1−x−yCd_xZn_yTe. Hall-effect results for both n-type (In) and p-type (As) Hg_1−x−yCd_xZn_yTe layers were very similar to HgCdTe control samples. We have also utilized x-ray rocking curve measurements with (246) asymmetric reflections as a novel sensitive technique to determine the correct amount of Zn needed to achieve lattice matching at an interface. MWIR/LWIR n-p-n two-color triple-layer heterojunction structures were grown to evaluate the effects of minimizing the lattice mismatch between the widest bandgap p-type collector layer, using Hg_1−x−yCd_xZn_yTe, and the HgCdTe MWIR and LWIR collector layers and compared to structures that did not incorporate the quaternary. Sequential mode two-color detectors were fabricated using a 256 × 256, 30 μm unit cell design. There were several interesting findings. Macro defects predominantly affected the LWIR band (Band 2) operability and had little effect on the MWIR band (Band 1). The incorporation of Hg_1−x−yCd_xZn_yTe p-type collector layers had little effect on MWIR detector performance, but overall the LWIR performance was generally better. These initial detector results indicate that the use of Hg_1−x−yCd_xZn_yTe alloys in multicolor detector structures are potentially promising and should be pursued further.     

Effect of annealing on the optical and structural properties of GaN:Er

The effect of annealing on the optical and structural properties of gallium nitride layers grown by metalorganic chemical vapor deposition and implanted with 0.8 to 2.0-MeV erbium ions at doses of (1−4)×10¹⁴ cm⁻² is investigated. Additional implantation of 0.11 to 0.28-MeV oxygen ions at doses of (1−4)×10¹⁵ cm⁻² is performed on some samples. Measurements of the Rutherford backscattering of protons show that amorphization of the gallium nitride layers does not occur at the erbium implantation doses investigated. The formation of erbium-related luminescence centers which emit at 1.54 μm ends before the defect structure of the implanted layers is restored during a postimplantation anneal in the temperature range 700–1300 °C. Fiz. Tekh. Poluprovodn. 33, 674–676 (June 1999)     

Long wavelength infrared, molecular beam epitaxy, HgCdTe-on-Si diode performance

In the past several years, we have made significant progress in the growth of CdTe buffer layers on Si wafers using molecular beam epitaxy (MBE) as well as the growth of HgCdTe onto this substrate as an alternative to the growth of HgCdTe on bulk CdZnTe wafers. These developments have focused primarily on mid-wavelength infrared (MWIR) HgCdTe and have led to successful demonstrations of high-performance 1024×1024 focal plane arrays (FPAs) using Rockwell Scientific’s double-layer planar heterostructure (DLPH) architecture. We are currently attempting to extend the HgCdTe-on-Si technology to the long wavelength infrared (LWIR) and very long wavelength infrared (VLWIR) regimes. This is made difficult because the large lattice-parameter mismatch between Si and CdTe/HgCdTe results in a high density of threading dislocations (typically, >5E6 cm⁻²), and these dislocations act as conductive pathways for tunneling currents that reduce the R_oA and increase the dark current of the diodes. To assess the current state of the LWIR art, we fabricated a set of test diodes from LWIR HgCdTe grown on Si. Silicon wafers with either CdTe or CdSeTe buffer layers were used. Test results at both 78 K and 40 K are presented and discussed in terms of threading dislocation density. Diode characteristics are compared with LWIR HgCdTe grown on bulk CdZnTe.     

MBE growth of HgCdTe on silicon substrates for large format MWIR focal plane arrays

HgCdTe p-on-n double layer heterojunctions (DLHJs) for mid-wave infrared (MWIR) detector applications have been grown on 100 mm (4 inch) diameter (211) silicon substrates by molecular beam epitaxy (MBE). The structural quality of these films is excellent, as demonstrated by x-ray rocking curves with full widths at half maximum (FWHMs) of 80–100 arcsec, and etch pit densities from 1 10⁶ to 7 10⁶ cm⁻². Morphological defect densities for these layers are generally less than 1000 cm⁻². Improving Hg flux coverage of the wafer during growth can reduce void defects near the edges of the wafers. Improved tellurium source designs have resulted in better temporal flux stability and a reduction of the center to edge x-value variation from 9% to only 2%. Photovoltaic MWIR detectors have been fabricated from some of these 100mm wafers, and the devices show performance at 140 K which is comparable to other MWIR detectors grown on bulk CdZnTe substrates by MBE and by liquid phase epitaxy.     

Metalorganic chemical vapor deposition of HgCdTe for photodiode applications

Metalorganic chemical vapor depositon (MOCVD) in situ growth of p-on-n junctions for long wavelength infrared (LWIR) and medium wavelength infrared (MWIR) photodiodes is reported. The interdiffused multilayer process was used for the growth of the HgCdTe junctions on CdTe and CdZnTe substrates. The n-type region was grown undoped while the p-type layer was arsenic doped using tertiarybutylarsine. Following a low temperature anneal in Hg vapor, carrier densities of (0.2-2) x 10¹⁵ cm³ and mobilities of (0.7-1.2) x 10⁵ cm²/V-s were obtained for n-type LWIR (x ~ 0.22) layers at 80K. Carrier lifetimes of these layers at 80 K are ~l-2 μs. For the p-type region arsenic doping was controlled in the range of (1-20) x 10¹⁶ cm^-3. Arsenic doping levels in the junctions were determined by calibrated secondary ion mass spectroscopy depth profile measurements. Composition and doping of the p-on-n heterojunctions could be independently controlled so that the electrical junction could be located deeper than the change in the composition. The graded composition region between the narrow and wide (x = 0.28-0.30) bandgap regions are 1–2 μm depending on the growth temperature. Backside-illuminated variable-area circular mesa photodiode arrays were fabricated on the grown junctions as well as on ion implanted n-on-p MWIR junctions. The spectral responses are classical in shape. Quantum efficiencies at 80K are 42–77% for devices without anti-reflection coating and with cutoff wavelengths of 4.8–11.0 μm. Quantum efficiencies are independent of reverse bias voltage and do not decrease strongly at lower temperatures indicating that valence band barrier effects are not present. 80K R_oA of 15.9 Ω-cm² was obtained for an array with 11.0 μm cutoff. Detailed measurements of the characteristics of the MOCVD in situ grown and implanted photodiodes are reported.     

Molecular beam epitaxy grown long wavelength infrared HgCdTe on Si detector performance

The use of silicon as a substrate alternative to bulk CdZnTe for epitaxial growth of HgCdTe for infrared (IR) detector applications is attractive because of potential cost savings as a result of the large available sizes and the relatively low cost of silicon substrates. However, the potential benefits of silicon as a substrate have been difficult to realize because of the technical challenges of growing low defect density HgCdTe on silicon where the lattice mismatch is ∼19%. This is especially true for LWIR HgCdTe detectors where the performance can be limited by the high (∼5×10⁶ cm⁻²) dislocation density typically found in HgCdTe grown on silicon. We have fabricated a series of long wavelength infrared (LWIR) HgCdTe diodes and several LWIR focal plane arrays (FPAs) with HgCdTe grown on silicon substrates using MBE grown CdTe and CdSeTe buffer layers. The detector arrays were fabricated using Rockwell Scientific’s planar diode architecture. The diode and FPA and results at 78 K will be discussed in terms of the high dislocation density (∼5×10⁶ cm²) typically measured when HgCdTe is grown on silicon substrates.     

Molecular beam epitaxial growth and performance of integrated two-color HgCdTe detectors operating in the mid-wave infrared band

The first report of molecular beam epitaxial growth and performance of HgCdTe two-color detectors for the simultaneous detection of radiation at 4.1 and 4.5 μm is presented. In-situ doped devices with the n-p-n architecture were grown by molecular beam epitaxy on (211)B CdZnTe substrates. Representative structures exhibited x-ray rocking curves with full width at half-maxima of 40–60 arcs. The typical near surface etch pit density in these structures were 4−7 × 10⁶ cm⁻². The devices were processed as mesa diodes and electrical contacts were made to the two n-type layers and the p-type layer to facilitate simultaneous operation of the two p-n junctions. The spectral response characteristics of the devices were characterized by sharp turn-on and turn-off for both bands, with R₀A values >5 × 10⁵ ωcm² at 77K. The detectors exhibited quantum efficiencies >70% in both bands.