首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 93 毫秒
1.
传统的大气辐射传输计算方法受计算资源和效率的限制已无法满足星载高光谱分辨率红外大气遥感资料处理的需要,基于单色波长辐亮度计算加权组合的方法,开发了一种快速准确的高光谱分辨率红外大气辐射传输的计算模型FFRTM_IR.利用FFRTM_IR模型,针对研制中的FY-3D红外高光谱大气探测仪(HIRAS)的光谱指标,模拟计算了仪器的观测通道亮温,并用独立样本对模拟亮温进行了验证和比较,结果显示:FFRTM_IR对HIRAS所有通道的模拟亮温偏差均小于0.06 K,标准差有效控制在0.1 K以内;在同等计算精度下,FFRTM_IR的计算速度略快于目前国际上通用的快速辐射传输计算模型CRTM.利用FFRTM_IR模型,采用解析计算方法可以进一步得到温度廓线、水汽廓线、二氧化碳、臭氧廓线以及地表参数的雅克比矩阵,计算结果与扰动法计算结果一致性较好,有较高的计算精度.计算和分析结果表明,初步建立了一种高效的红外大气辐射传输计算模型,可用于星载高光谱红外大气探测仪器的观测仿真和资料处理.  相似文献   

2.
风云三号E星(FY-3E)搭载的高光谱大气探测仪(HIRAS-II)能够实现大气的垂直探测,具有高光谱、高灵敏度、高精度的特点。仪器在轨之后由于仪器衰减和环境变化的原因产生非线性响应,影响在轨定标精度。针对非线性响应的问题,提出了一种基于带内光谱的非线性校正方法。首先基于带外低频光谱的非线性特征求解非线性校正系数,将此系数作为初值输入到辐射定标模型中,以星上测量的黑体带内光谱与理想光谱的偏差为目标函数,通过迭代优化非线性校正系数。通过辐射定标实验得出,校正后的黑体亮温偏差明显低于未校正和基于带外光谱的校正方法。将HIRAS-II的观测数据与IASI进行交叉比对并计算平均亮温偏差和偏差绝对值,经过带内校正法非线性校正后的亮温平均偏差为-0.13K,优于带外校正方法。  相似文献   

3.
在中国新一代气象卫星风云三号搭载的遥感器中,不同遥感器设有相近的通道.针对扫描辐射计(VIRR)第四通道(波段范围10.3~11.3μm)和中分辨率光谱成像仪(MERSI)第五通道(中心波长11.25μm),应用精确的逐线辐射传输模式(LBLRTM)模拟计算了红外波段8~14μm大气顶向外出射的光谱辐射率,大气廓线采用ECMWF再分析产生的具有代表性的全球52条大气廓线数据集.结合上述两个通道的光谱响应函数,计算了卫星接收到的大气顶出射辐射,从理论上分析了两个通道观测亮温之间的关系.应用2008年9月青海湖辐射校正场FY-3实际观测数据,检验了两个通道的关系.比较结果表明:LBLRTM模拟计算得到的MERSI和VIRR两个红外窗区通道的亮温有较好的一致性和线性关系,MERSI稍低于VIRR,偏差随温度的升高而线性增加.实际观测数据受诸多因素的影响,通道对比结果与理论模拟有一定的差异,VIRR观测亮温低于MERSI.结合MODIS的观测数据,分别与两个通道的观测结果进行了对比,确认了VIRR可能较低地估计了温度,MERSI与MODIS的符合程度在温度探测的绝对精度范围之内.该研究结果有助于评价MERSI和VIRR两个红外相似通道观测结果的异同性.  相似文献   

4.
大气吸收波段对于从卫星高度向下探测空间亮目标有特殊的优势,使用辐射传输模式MODTRAN5模拟计算了中红外大气吸收波段不同光谱分辨率100 km高度大气背景辐亮度的变化.将三个波段不同分辨率的结果平滑到统一分辨率进行对比表明:4.3 mm不同光谱分辨率相对误差最大可超过10%;其中0.2 cm-1光谱分辨率的计算结果与精确的逐线积分最为接近;3.2 μm与2.7μm波段不同光谱分辨率的计算结果误差较小,其中2.7 μm波段最大误差小于5%.进一步将MODTRAN4和MODTRAN5的1cm-1、5 cm-1光谱分辨率计算结果与逐线积分做了比较,表明使用MODTRAN5的低光谱分辨率计算4.3 mm波段的辐亮度可能产生较大误差.  相似文献   

5.
地基大气背景红外光谱辐射特性测量   总被引:1,自引:1,他引:0  
用傅里叶变换红外光谱辐射计(FTIR)在地面测量了较高分辨率(1 cm-1)下的大气向下背景光谱辐射,获得了长波红外5~14μm波段的大气背景辐射光谱。研究了大气背景红外光谱辐射与整层大气透过率的关系。从实验数据中研究了不同波段大气背景辐射随观测天顶角的变化。结果表明:地基大气向下的长波背景辐射亮温随着整层大气透过率的增大而减小;大气背景辐射随观测天顶角增大而增大;在大气窗口区,大气背景辐射随观测天顶角变化较快,在强吸收波段,大气背景辐射随观测天顶角几乎不变化。  相似文献   

6.
利用辐射传输模型MODTRAN5模拟计算了红外高光谱仪在光谱分辨率、光谱定标精度、地面反射率、大气廓线以及辐射分辨率对CO_2气体含量探测敏感性的影响,同时定义探测辐亮度随气体含量改变的变化量指标S值,并对探测灵敏度、光谱分辨率和信噪比SNR的关系进行了综合分析。为我国红外高光谱大气探测仪的设计以及高光谱大气成分反演研究的开展提供重要的科学依据。对CO_2柱总量反演通道的选择和实现CO_2气体探测敏感参数分析具有重要的参考价值。  相似文献   

7.
利用辐射传输模型MODTRAN5模拟计算了红外高光谱仪在光谱分辨率、光谱定标精度、地面反射率、大气廓线以及辐射分辨率对CO2气体含量探测敏感性的影响,同时定义探测辐亮度随气体含量改变的变化量指标S值,并对探测灵敏度、光谱分辨率和信噪比SNR的关系进行了综合分析。为我国红外高光谱大气探测仪的设计以及高光谱大气成分反演研究的开展提供重要的科学依据。对CO2柱总量反演通道的选择和实现CO2气体探测敏感参数分析具有重要的参考价值。  相似文献   

8.
观测热带气旋所需的空间分辨率以及识别出变化所需的时间分辨率对于用于观测热带气旋的辐射计的指标设计有重要意义.利用美国国家环境预报中心6 h全球最终分析资料作为初始场, 通过中尺度数值天气预报模式输出不同时刻水凝物含量和温湿度廓线等参数, 使用欧洲中期数值天气预报中心发展建立的快速辐射传输模式输出亮温, 分析了不同时刻及不同空间分辨率下氧气吸收频段和水汽吸收频段的静止轨道探测模拟亮温.结果表明:热带气旋等级越高, 观测的空间分辨率需求越高, 氧气吸收频率、水汽吸收频率、窗区频率对空间分辨率敏感度依次增大; 短时间内低等级热带气旋的观测时间分辨率需求越高, 水汽吸收频段探测频率所需时间分辨率高于氧气吸收频段.  相似文献   

9.
杨天杭  张春明  左丰华  胡勇  顾明剑 《红外与激光工程》2023,52(4):20220616-1-20220616-12
星载红外高光谱传感器与多通道光谱传感器在轨交叉定标时能够提升数据精度和质量,交叉定标样本通常采用星下点交叉方式匹配筛选,包括空间、时间、观测几何角度和光谱匹配,匹配误差的不确定性将对最终交叉定标精度产生影响。采用FY-3E同平台红外高光谱大气探测仪HIRAS-II和中分辨率光谱成像仪MERSI-LL均匀晴空背景进行观测,根据视线向量匹配HIRAS-II星下点瞬时视场内的MERSI-LL像素,分别通过模拟视场偏移、观测天顶角偏差和光谱响应函数变化单独分析空间、观测几何角度和光谱匹配误差引入的匹配不确定度。结果表明,空间失配引起观测背景辐射亮温变化,偏移一半像元视场时的相对不确定度约为10%,达到一个像元时为25%~30%;观测几何角度失准引起光谱辐射亮温变化,观测天顶角偏移20°时的不确定度优于0.2%;光谱响应函数差异引起光谱等效辐射亮温变化,响应函数发生展宽时对吸收通道的不确定度最大约为2.5%,窗区通道为0.4%,收缩时的不确定度整体优于0.3%,平移引起的不确定度相对较小,移动5倍波长间隔时优于0.1%。  相似文献   

10.
基础研究表明大气微量气体成分的精确反演需要超高分辨率光谱数据,空间外差光谱技术是近年来得以迅速发展的新型超光谱分析技术,综合了光栅及傅里叶变换光谱技术的特点。对空间外差光谱技术基本原理进行了分析,阐述了空间外差干涉数据复原光谱信息流程。针对大气主要温室气体CO_2开展空间外差光谱技术在大气遥感探测方面的应用研究,通过地基遥感观测实验,分析空间外差光谱系统的探测灵敏度,验证超光谱数据对大气微量气体浓度变化检测能力。实验表明空间外差光谱技术在大气遥感探测尤其是微量气体成份探测中具有针对性和优越性。  相似文献   

11.
LCTF 成像光谱技术是近年来快速发展的一种成像光谱技术,具有光谱分辨率高、谱段范围宽、质量轻等诸多优点,在月球矿物探测高光谱成像遥感器中具有独特的优势。LCTF 中液晶材料温度变化会引起双折射率偏差变大,从而影响LCTF 光谱仪成像质量。通过对光谱仪工作环境的热分析,综合考虑光谱仪的工作模式及各部件工作温度要求,设计了LCTF 光谱仪热控系统。仿真结果表明,该热控系统能较好地满足设计要求,使LCTF 光谱仪清晰成像,为月球矿物探测做好硬件准备。  相似文献   

12.
谢锋  刘成玉  邵红兰  张长兴  杨贵  王建宇 《红外与激光工程》2017,46(1):138001-0138001(6)
传感器每个波段的中心波长和半高全宽(Full Width at Half Maximum,FWHM)随成像环境变化会发生较大的系统性漂移。这种漂移最终会影响发射率和温度的反演精度,尤其是在大气吸收波段附近的发射率反演精度。选择水汽在11.73 m处的吸收通道作为参考波段,提出了适用于热红外高光谱数据的光谱定标技术流程。模拟实验表明:光谱分辨率为50 nm,中心波长偏移在-50~50 nm、FWHM变化在-25~25 nm时,大气水汽含量对光谱定标误差的影响最大。同时,对误差分布曲面进行拟合得到描述误差分布模型,用于误差的估计。当大气水汽含量足够大时,光谱中心波长偏移估算误差可达到1 nm以内。最后,将所提方法应用于机载热红外高光谱数据光谱定标。结果显示,热红外高光谱成像仪中心波长偏移为28.4 nm,FWHM变化为-18.5 nm。  相似文献   

13.
A maximum a posteriori (MAP) estimation method for improving the spatial resolution of a hyperspectral image using a higher resolution auxiliary image is extended to address several practical remote sensing situations. These include cases where: 1) the spectral response of the auxiliary image is unknown and does not match that of the hyperspectral image; 2) the auxiliary image is multispectral; and 3) the spatial point spread function for the hyperspectral sensor is arbitrary and extends beyond the span of the detector elements. The research presented follows a previously reported MAP approach that makes use of a stochastic mixing model (SMM) of the underlying spectral scene content to achieve resolution enhancement beyond the intensity component of the hyperspectral image. The mathematical formulation of a generalized form of the MAP/SMM estimate is described, and the enhancement algorithm is demonstrated using various image datasets.  相似文献   

14.
15.
Super-resolution reconstruction of hyperspectral images.   总被引:2,自引:0,他引:2  
Hyperspectral images are used for aerial and space imagery applications, including target detection, tracking, agricultural, and natural resource exploration. Unfortunately, atmospheric scattering, secondary illumination, changing viewing angles, and sensor noise degrade the quality of these images. Improving their resolution has a high payoff, but applying super-resolution techniques separately to every spectral band is problematic for two main reasons. First, the number of spectral bands can be in the hundreds, which increases the computational load excessively. Second, considering the bands separately does not make use of the information that is present across them. Furthermore, separate band super-resolution does not make use of the inherent low dimensionality of the spectral data, which can effectively be used to improve the robustness against noise. In this paper, we introduce a novel super-resolution method for hyperspectral images. An integral part of our work is to model the hyperspectral image acquisition process. We propose a model that enables us to represent the hyperspectral observations from different wavelengths as weighted linear combinations of a small number of basis image planes. Then, a method for applying super resolution to hyperspectral images using this model is presented. The method fuses information from multiple observations and spectral bands to improve spatial resolution and reconstruct the spectrum of the observed scene as a combination of a small number of spectral basis functions.  相似文献   

16.
发展高光谱微波辐射计对于提升大气参数反演精度具有重要意义。利用微波辐射传输模型mpm93以及BP 神经网络方法分别构建正演上行辐射亮温和反演大气温度廓线的模型,并研究了晴空条件下高光谱微波辐射计反演大气温度廓线的精度。54~58 GHz、64~68 GHz 在氧气吸收波段选取80 个通道作为高光谱通道,基于2015 年5~12 月昆明的探空资料进行正、反演仿真实验。选取微波成像仪/ 探测仪(SSMIS)的9 个温度探测通道进行对比实验,评估分析反演效果。实验结果表明:在大气3~10 km 高度范围内,高光谱通道的反演精度较SSMIS 提高了0.3 ~0.6 K;在0~3 km 高度范围内,反演精度提高了1 K。  相似文献   

17.
航天高光谱成像技术研究现状及展望   总被引:1,自引:0,他引:1  
自1997年8月23日首颗高光谱卫星LEWIS发射以来,航天高光谱成像技术走过了15年的路程,我国在该领域的技术也取得了跨越式的发展。当前我国正按照国家中长期科技规划,努力构建下一代高分辨率对地观测系统,深入全面地总结过去若干年的航天高光谱成像技术发展情况,并分析发达国家的发展计划,对制定我国的航天高光谱成像技术发展战略具有重要意义。从当前的主流高光谱分光技术、应用情况和发展趋势三个方面进行了全面的分析总结,认为民用高光谱成像系统应该朝着宽幅、定量化和应用细分的方向发展;军用高光谱成像系统的发展重点应该是高空间分辨率、宽波段以及快速信息处理技术。  相似文献   

18.
Passive microwave Earth observing systems provide coarse resolution data. Heterogeneity in physical characteristics will typically be present within footprints, especially over land. How this affects the development and validation of methods of retrieving soil moisture has not been verified. In this study, aircraft-based 1.4 GHz microwave radiometer data were collected sit several altitudes over test sites where soil moisture was measured concurrently. The use of multiple flightlines at lower altitudes allowed the direct comparison of different spatial resolutions using independent samples over the same ground location. Results showed that the brightness temperature data from 1.4 GHz sensor in this study region provides the same mean values for an area regardless of the spatial resolution of the original data. The relationship between brightness temperature and soil moisture was similar at different resolutions. These results suggest that soil moisture retrieval methods developed using high resolution data can be extrapolated to satellite scales  相似文献   

19.
Hyperspectral imagery has been widely used in military and civilian research fields such as crop yield estimation, mineral exploration, and military target detection. However, for the limited imaging equipment and the complex imaging environment of hyperspectral images, the spatial resolution of hyperspectral images is still relatively low, which limits the application of hyperspectral images. So, studying the data characteristics of hyperspectral images deeply and improving the spatial resolution of hyperspectral images is an important prerequisite for accurate interpretation and wide application of hyperspectral images. The purpose of this paper is to deal with super-resolution of the hyperspectral image quickly and accurately, and maintain the spectral characteristics of the hyperspectral image, makes the spectral separability of the substrate in the original image remains unchanged after super-resolution processing. This paper first learns the mapping relationship between the spectral difference of low-resolution hyperspectral image and the spectral difference of the corresponding high-resolution hyperspectral image based on multiple scale convolutional neural network, Thus, apply this mapping relationship to the input low-resolution hyperspectral image generally, getting the corresponding high resolution spectral difference. Constrained space by using the image of reconstructed spectral difference, this requires the low-resolution hyperspectral image generated by the reconstructed image is to be close to the input low-resolution hyperspectral image in space, so that the whole process becomes a closed circulation system where the low-resolution hyperspectral image generation of high-resolution hyperspectral images, then back to low-resolution hyperspectral images. This innovative design further enhances the super-resolution performance of the algorithm. The experimental results show that the hyperspectral image super-resolution method based on convolutional neural network improves the input image spatial information, and the super-resolution performance of the model is above 90%, which can maintain the spectral information well.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号