共查询到19条相似文献,搜索用时 93 毫秒
1.
2.
3.
角锥棱镜后向衍射特性的Zemax分析 总被引:1,自引:0,他引:1
当角锥棱镜(CCR)作为激光的合作目标时.其后向空间衍射特性是进行系统设计所必须考虑的.Zemax具有强大的物理光学计算能力,可对非序列光学元件角锥棱镜的后向衍射特性进行仿真,仿真结果精度高,方法简便具有通用性.首先建立了角锥棱镜的几何模型.分别计算了在垂直和倾斜入射条件下,理想和具有二面角误差角锥棱镜近场和远场的衍射图样,最后考虑偏振效应下角锥棱镜的衍射图像,将近场模拟结果与实际测量值进行了对比,具有非常好的一致性.根据定量的仿真计算结果,得到了一系列有益于工程设计的结论,借助于Zemax,将对不同使用要求的角锥棱镜及其系统设计产生极大便利. 相似文献
4.
以衍射理论为基础,建立了椭偏高斯光束通过非线性介质后远场光强分布的理论模型。利用该理论模型采用数值模拟的方法研究了椭偏高斯光束与非线性介质相互作用后在远场形成的衍射图样随椭偏光椭偏率变化的演化规律。分析发现,在不同非线性机制下,椭偏率的变化对远场衍射图样的影响明显不同。在分子取向机制下,非线性介质对入射椭偏高斯光束椭偏率变化的响应最敏感,不仅影响衍射图样的分布尺寸和衍射环的数目,而且还影响远场衍射图样中央光斑的亮暗。由于线偏振和圆偏振是椭圆偏振的特殊情况,本文所建立的模型也适用于入射光束偏振态为线偏振或圆偏振态的情况。 相似文献
5.
理论分析了角锥棱镜腔Nd:YAG固体激光器的特性,通过数值模拟得出结论,角锥棱镜谐振腔对角锥棱镜的平移失调有一定的敏感性,而对输出镜的角度失调是不敏感的.利用菲涅耳一基尔霍夫衍射方程,模拟出角锥棱镜腔近场模式,该模式由六个瓣状结构组成,与实际光斑相吻合.根据斯托克斯参量分析出,角锥棱镜出射光的偏振态随角锥棱镜转动发生改变,出射的椭圆偏振光的椭圆率和方位角随着角锥棱镜的转动发生改变. 相似文献
6.
7.
对LiNbO3晶体中光折变光栅的各向异性衍射进行了定量研究。基于有效电光系数非零和布拉格相位匹配条件,对在LiNbO3晶体中各向异性衍射的衍射效率与光束偏振态和写入几何的关系进行了较为详细的理论计算和分析,根据建立的数学模型进行了数值计算,发现光轴垂直于写入平面时,写入的光栅可发生显著的各向异性衍射。实验测量与理论计算结果基本符合。 相似文献
8.
为了校正角锥棱镜阵列中子孔径的piston误差,设计了一种多单元一维相位精密调整机构,提出了一种基于相干合成原理的角锥棱镜阵列piston误差检测、调整方法。首先,设计了一种机械装置使单个角锥棱镜能够进行一维相位调整;其次,利用远场成像原理,分析了角锥阵列piston误差对远场衍射成像的影响;最后,基于远场光斑的不同,提出了一种角锥阵列piston误差的检测、调整方法。实验结果表明:角锥阵列相位精密调整机构能够达到0.1 μm级的调整精度,通过观测角锥棱镜阵列反射光束远场衍射图像,调整角锥棱镜单元相对位置,将反射光束PIB提升至0.49,远场图像接近仿真结果,基本实现了角锥棱镜阵列子孔径的piston误差的校正,提升了角锥棱镜阵列使用效率,扩展了角锥棱镜阵列使用场景。 相似文献
9.
提出一种基于液晶光阀(LCLV)和光束分析仪(LBP)直接测量Goos-Hänchen(GH)位移的新方法。在文中我们首先研究了LCLV对光偏振态调制的特性,结果发现,当控制电压发生变化时,光的偏振态也随之变化。然后利用LCLV对光偏振态的调制和LBP记录光斑的重心位置的变化,直接测量出TE和TM两种偏振态入射时棱镜单界面反射光束的GH位移差。这个探测方法简单,不需要复杂的外部处理电路,且实验结果与理论结果很吻合,这个方法也可以进一步直接测量二维位移。 相似文献
10.
11.
12.
B.B. Jian 《Photonics Technology Letters, IEEE》1996,8(12):1609-1611
The effect of the corner reflector size on the performance of an etched corner reflector array laser is studied. Experimental evidence is presented to show that the operation of the corner reflector array laser is governed by the diffraction principle. The light output increases markedly if the reflector size is large enough so that diffraction can be neglected. This general principle should prove useful in the design of unguided photonic integrated circuits. 相似文献
13.
14.
E. Sauter G. V. Schultz R. Wohlleben 《Journal of Infrared, Millimeter and Terahertz Waves》1984,5(4):451-463
To verify the enhancement in sensitivity of a Schottky barrier diode using a 90° corner reflector at submillimeter wavelength a 65∶1 scaled model of the open structure mixer was constructed and investigated at 2.8 cm wavelength. The results show clearly the advantage of a 90° corner reflector, the reality of the deviations for 45° and 60° corner reflectors found for submillimeter wavelengths, and the equality of the antenna patterns for a 90° corner reflector and a “cat-eye” (corner cube) reflector. 相似文献
15.
立方反射镜失调特性的研究 总被引:4,自引:2,他引:4
结合理想坐标系下立方镜镜面微小倾斜后其三个平面法线坐标,利用刚体微量转动的反射法线向量公式,获得非理想立方镜反射矩阵;为了研究在光斜入射时镜面倾斜对出射光方向的影响,利用立方镜绕顶点旋转等效于光斜入射的方法,计算出光束夹角δ与单一镜面偏差角ε和立方镜旋转角θ之间的关系式;对于理想情况下的立方镜,利用几何光学可以证明出射光与入射光不但平行,而且过顶点作任意截面交于两光线所得的两个交点关于顶点对称,从而计算出立方镜绕顶点以外任意轴旋转造成出射光束相对原出射光的偏移量与旋转角关系式,理论计算值与实验数据吻合得很好;介绍了立方镜的制作、调整及检测方法,偏差角的测量与计算。 相似文献
16.
角锥棱镜的偏振特性会产生退偏效应影响免调试固体激光器的输出质量和效率,也可以实现相干互注入用于激光合成领域。无论是光的合成还是退偏效应的消除,都需要有精确的偏振特性数据。利用解析几何和光线追迹法从理论上推导出角锥六种光回路的Mueller偏振变换矩阵。为了提高测量精度和稳定性,设计了一种动态检测Stokes参量的方法,通过实验获得角锥棱镜六种传输光路的高精度数据,实验与理论的误差率为4.470%,误差在合理范围内,可以确定其偏振特性。所做研究将有助于消除角锥棱镜的退偏效应,提高免调试固体激光器等设备的性能,提高激光合成效率和质量。 相似文献
17.
从理论上分析了一些引起傅立叶变换光谱仪信号调制度下降的原因,具体的就平面镜面形、偏振态、探测器横向位置偏移、平面镜倾斜、角锥反射镜顶点之间的横向偏移等作了一定的分析,得到了几个重要的公式,并就这些公式的用途作了简短的说明。 相似文献
18.
《Proceedings of the IEEE. Institute of Electrical and Electronics Engineers》1987,75(12):1686-1688
We have analyzed radar polarimeter signals from a set of trihedral corner reflectors located in the Goldstone Dry Lake in Cafifornia, and observed three types of scattering behavior: i) Bragg-like slightly rough surface scattering that represents the background signal from the dry lake, ii) trihedral corner reflector scattering that returns the incident polarization, and iii) two-bounce corner reflector scattering resulting from a particular alignment of a trihedral reflector. In the latter case, we can measure within about 3° the orientation angle of the apparent dihedral trough, even though the 2-m reflector is much smaller than the 10-m resolution element of our radar. Thus a radar calibration approach using trihedral corner reflectors should be designed such that precise alignment of the reflectors is ensured, as three-bounce and two-bounce geometries lead to very different cross sections and hence very different inferred calibration factors. 相似文献
19.
RCS analysis and reduction for lossy dihedral corner reflectors 总被引:3,自引:0,他引:3
Griesser T. Balanis C.A. Liu K. 《Proceedings of the IEEE. Institute of Electrical and Electronics Engineers》1989,77(5):806-814
The radar cross-section patterns of lossy dihedral corner reflectors are calculated using a uniform geometrical theory of diffraction for impedance surfaces. All terms of up to third order reflections and diffractions are considered for patterns in the principal plane. The surface waves are included whenever they exist for reactive surface impedances. The dihedral corner reflectors examined have right, obtuse, and acute interior angles, and patterns over the entire 360° azimuthal plane are calculated. The surface impedances can be different on the four faces of the dihedral corner reflector; however, the surface impedance must be uniform over each face. Computed cross sections are compared with a moment method technique for a dielectric/ferrite absorber coating on a metallic corner reflector. The analysis of the dihedral corner reflector is important because it demonstrates many of the important scattering contributors of complex targets including both interior and exterior wedge diffraction, half-plane diffraction, and dominant multiple reflections and diffractions 相似文献