Highly Efficient Hole Injection Using Polymeric Anode Materials for Small‐Molecule Organic Light‐Emitting Diodes

A novel, highly efficient hole injection material based on a conducting polymer polythienothiophene (PTT) doped with poly(perfluoroethylene‐perfluoroethersulfonic acid) (PFFSA) in organic light‐emitting diodes (OLEDs) is demonstrated. Both current–voltage and dark‐injection‐current transient data of hole‐only devices demonstrate high hole‐injection efficiency employing PTT:PFFSA polymers with different organic charge‐transporting materials used in fluorescent and phosphorescent organic light‐emitting diodes. It is further demonstrated that PTT:PFFSA polymer formulations applied as the hole injection layer (HIL) in OLEDs reduce operating voltages and increase brightness significantly. Hole injection from PTT:PFFSA is found to be much more efficient than from typical small molecule HILs such as copper phthalocyanine (CuPc) or polymer HILs such as polyethylene dioxythiophene: polystyrene sulfonate (PEDOT‐PSS). OLED devices employing PTT:PFFSA polymer also demonstrate significantly longer lifetime and more stable operating voltages compared to devices using CuPc.     

Efficient Charge Carrier Injection and Balance Achieved by Low Electrochemical Doping in Solution‐Processed Polymer Light‐Emitting Diodes

Charge carrier injection and transport in polymer light‐emitting diodes (PLEDs) is strongly limited by the energy level offset at organic/(in)organic interfaces and the mismatch in electron and hole mobilities. Herein, these limitations are overcome via electrochemical doping of a light‐emitting polymer. Less than 1 wt% of doping agent is enough to effectively tune charge injection and balance and hence significantly improve PLED performance. For thick single‐layer (1.2 µm) PLEDs, dramatic reductions in current and luminance turn‐on voltages (V_J = 11.6 V from 20.0 V and V_L = 12.7 V from 19.8 V with/without doping) accompanied by reduced efficiency roll‐off are observed. For thinner (<100 nm) PLEDs, electrochemical doping removes a thickness dependence on V_J and V_L, enabling homogeneous electroluminescence emission in large‐area doped devices. Such efficient charge injection and balance properties achieved in doped PLEDs are attributed to a strong electrochemical interaction between the polymer and the doping agents, which is probed by in situ electric‐field‐dependent Raman spectroscopy combined with further electrical and energetic analysis. This approach to control charge injection and balance in solution‐processed PLEDs by low electrochemical doping provides a simple yet feasible strategy for developing high‐quality and efficient lighting applications that are fully compatible with printing technologies.     

以聚乙烯亚胺作为电子注入层的聚合物发光器件特性研究

在传统结构与倒置结构的有机发光二极管(LED)的聚合物发光层和阴极之间加入聚乙烯亚胺(PEIE)层能够显著地提高器件的发光效率。通过采用不同厚度的PEIE层的器件发光特性研究表明:PEIE层作为电子注入层(EIL)/空穴阻挡层(HBL)来平衡器件中的电子和空穴浓度,这主要来源于PEIE作为界面偶极层,能有效地降低阴极与发光层之间的电子注入势垒。     

Solution‐Processed Organic Light‐Emitting Transistors Incorporating Conjugated Polyelectrolytes

Improved performance of p‐type organic light‐emitting transistors (OLETs) is demonstrated by introducing a conjugated polyelectrolyte (CPE) layer and symmetric high work function (WF) source and drain metal electrodes. The OLET comprises a tri‐layer film consisting of a hole transporting layer, an emissive layer, and a CPE layer as an electron injection layer. The thickness of the CPE layer is critical for achieving good performance and provides an important structural handle for consideration in future optimization studies. We also demonstrate for the first time, good performance solution‐processed blue‐emitting OLETs. These results further demonstrate the simplification of device fabrication and improved performance afforded by integrating CPE interlayers into organic optoelectronic devices.     

Optimization of carrier transport layer: A simple but effective approach toward achieving high efficiency all-solution processed InP quantum dot light emitting diodes

High performance quantum dot light emitting diodes (QD-LED) are being considered as a next-generation technology for energy efficient solid-state lighting and displays. In recent years, cadmium (Cd)-based QLEDs have made great progress in performance, which is close to commercial applications. However, the performance of environmentally friendly Cd-free QD-LED still needs to be improved. In this letter, using InP/ZnS quantum dots (QDs), an environmentally friendly red QDs material, as the light emitting layer, low-cost all-solution processed red InP/ZnS QD-LED are fabricated. The optimized device with a hybrid multilayered structure employing an organic double hole transport layer (HTL) with doping small molecules (TFB/PVK:TAPC) and an inorganic ZnMgO nanoparticles (NPs) electron transport layer (ETL), here TFB, PVK and TAPC represent poly [(9,9-dioctylfluorenyl-2,7-diyl)-co-(4,4’-(N-(p-butylphenyl))-diphenylamine)], poly (9-vinlycarbazole) and 1,1-bis [4-[N,N′-di (p-tolyl)amino]phenyl]-cyclohexane, respectively. The best device exhibits a peak current efficiency (CE) of 7.58 cd A⁻¹, which is 2.4 times higher than the control device using PVK (HTL) and ZnO (ETL). At the same time, turn-on voltage dropped from 2.8 V (control devices) to 2.4 V. These superb QD-LED performances originate not only from the improved hole injection by the introduction of a double hole layer and the reduced the quenching of excitons by using ZnMgO NPs ETL but also from increasing the hole mobility with doping of small molecule materials in PVK to balance the carrier transportation. This work provides a simple and feasible idea with optimization the carrier transport for realizing high-efficiency QD-LED devices.     

Solution‐Processed Zinc Oxide as High‐Performance Air‐Stable Electron Injector in Organic Ambipolar Light‐Emitting Field‐Effect Transistors

Electron injection from the source–drain electrodes limits the performance of many n‐type organic field‐effect transistors (OFETs), particularly those based on organic semiconductors with electron affinities less than 3.5 eV. Here, it is shown that modification of gold source–drain electrodes with an overlying solution‐deposited, patterned layer of an n‐type metal oxide such as zinc oxide (ZnO) provides an efficient electron‐injecting contact, which avoids the use of unstable low‐work‐function metals and is compatible with high‐resolution patterning techniques such as photolithography. Ambipolar light‐emitting field‐effect transistors (LEFETs) based on green‐light‐emitting poly(9,9‐dioctylfluorene‐alt‐benzothiadiazole) (F8BT) and blue‐light‐emitting poly(9,9‐dioctylfluorene) (F8) with electron‐injecting gold/ZnO and hole‐injecting gold electrodes show significantly lower electron threshold voltages and several orders of magnitude higher ambipolar currents, and hence light emission intensities, than devices with bare gold electrodes. Moreover, different solution‐deposited metal oxide injection layers are compared. By spin‐coating ZnO from a low‐temperature precursor, processing temperatures could be reduced to 150 °C. Ultraviolet photoemission spectroscopy (UPS) shows that the improvement in transistor performance is due to reduction of the electron injection barrier at the interface between the organic semiconductor and ZnO/Au compared to bare gold electrodes.     

Efficient red phosphorescent organic light emitting diodes based on solution processed all-inorganic cesium lead halide perovskite as hole transporting layer

An efficient red phosphorescent organic light emitting diode (PhOLED) has been realized by utilizing a composite hole transporting layer comprised of all-inorganic cesium lead halide perovskite CsPbBr₃ via spin-coating and 1,3-bis(9-carbazolyl) benzene (mCP) by vacuum depositing, in which CsPbBr₃ film is used as a hole transporting layer and mCP plays a dominant role in electron and exciton blocking. And this PhOLED shows a saturated red emission coordinated at CIE (0.65, 0.33) driven at 7.5 V, a maximum brightness of 20,750 cd/m², and a maximum current efficiency of 10.64 cd/A, which is as 1.87 times as that 5.68 cd/A of the reference PhOLEDs based on traditional small organic molecular hole transporting material N,N′-bis(naphthalen-1-yl)-N,N′-bis(phenyl)-benzi (NPB). The electroluminescent (EL) spectra and the energy level alignment of different PhOLEDs are investigated. The enhanced EL performances are ascribed to improved hole injecting and transporting behaviors, and better electron and exciton confinements by introducing the composite hole transporting layer CsPbBr₃/mCP.     

Improved efficiency in fluorescent blue organic light emitting diode with a carrier confining structure

A blue organic light emitting device (OLED) with improved efficiency and good color purity is reported. The highest occupied molecular orbital (HOMO) level of the hole transport layer (HTL) and that of the emissive layer (EML) differs by 0.3 eV. This energy level mismatch confines the carriers at the HTL/EML interface. Conventional devices have only one HTL/EML interface, with a current efficiency of 2.9 cd/A. Without adding a separate hole blocking layer, incorporating multi-layers of the same HTL and EML increases this efficiency to 5.8 cd/A, with only a small increase in operating voltage yielding increased power efficiency also. But, there are an optimum number of layers, beyond which efficiency loss results. Also, including the multilayer structure simultaneously improves the blue color co-ordinates. To gain insight into the role of multilayer structures in modifying charge transport and recombination zone a simulator was developed. The simulated results could qualitatively explain the experimental observations.     

Synergistic Use of Pyridine and Selenophene in a Diketopyrrolopyrrole‐Based Conjugated Polymer Enhances the Electron Mobility in Organic Transistors

To achieve semiconducting materials with high electron mobility in organic field‐effect transistors (OFETs), low‐lying energy levels (the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO)) and favorable molecular packing and ordering are two crucial factors. Here, it is reported that the incorporation of pyridine and selenophene into the backbone of a diketopyrrolopyrrole (DPP)‐based copolymer produces a high‐electron‐mobility semiconductor, PDPPy‐Se. Compared with analogous polymers based on other DPP derivatives and selenophene, PDPPy‐Se features a lower LUMO that can decrease the electron transfer barrier for more effective electron injection, and simultaneously a lower HOMO that, however, can increase the hole transfer barrier to suppress the hole injection. Combined with thermal annealing at 240 °C for thin film morphology optimization to achieve large‐scale crystallite domains with tight molecular packing for effective charge transport along the conducting channel, OFET devices fabricated with PDPPy‐Se exhibit an n‐type‐dominant performance with an electron mobility (μ_e) as high as 2.22 cm² V^?1 s^?1 and a hole/electron mobility ratio (μ_h/μ_e) of 0.26. Overall, this study demonstrates a simple yet effective approach to boost the electron mobility in organic transistors by synergistic use of pyridine and selenophene in the backbone of a DPP‐based copolymer.     

High-efficiency hybrid organic–inorganic light-emitting devices

We report efficient red, orange, green and blue organic–inorganic light emitting devices using light emitting polymers and polyethylenimine ethoxylated (PEIE) interlayer with the respective luminance efficiency of 1.3, 2.7, 10 and 4.1 cd A⁻¹, which is comparable to that of the analogous conventional devices using a low work-function metal cathode. This is enabled by the enhanced electron injection due to the effective reduction of the ZnO work-function by PEIE, as well as hole/exciton-blocking function of PEIE layer. Due to the benign compatibility between PEIE and the neighboring organic layer, the novel phosphorescent organic–inorganic devices using solution-processed small molecule emissive layer show the maximum luminance efficiency of 87.6 cd A⁻¹ and external quantum efficiency of 20.9% at 1000 cd m⁻².     

Origin of Enhanced Hole Injection in Inverted Organic Devices with Electron Accepting Interlayer

Conventional organic light emitting devices have a bottom buffer interlayer placed underneath the hole transporting layer (HTL) to improve hole injection from the indium tin oxide (ITO) electrode. In this work, a substantial enhancement in hole injection efficiency is demonstrated when an electron accepting interlayer is evaporated on top of the HTL in an inverted device along with a top hole injection anode compared with the conventional device with a bottom hole injection anode. Current–voltage and space‐charge‐limited dark injection (DI‐SCLC) measurements were used to characterize the conventional and inverted N,N′‐diphenyl‐N,N′‐bis(1‐naphthyl)(1,1′biphenyl)‐4,4′diamine (NPB) hole‐only devices with either molybdenum trioxide (MoO₃) or 1,4,5,8,9,11‐hexaazatriphenylene hexacarbonitrile (HAT‐CN) as the interlayer. Both normal and inverted devices with HAT‐CN showed significantly higher injection efficiencies compared to similar devices with MoO₃, with the inverted device with HAT‐CN as the interlayer showing a hole injection efficiency close to 100%. The results from doping NPB with MoO₃ or HAT‐CN confirmed that the injection efficiency enhancements in the inverted devices were due to the enhanced charge transfer at the electron acceptor/NPB interface.     

Efficient and stable red organic light emitting devices from a tetradentate cyclometalated platinum complex

An efficient and stable red phosphorescent organic light emitting diode was developed using a tetradentate cyclometalated platinum complex. Devices employing the phosphorescent molecule, platinum(II)-9-(4-methylpyridin-2-yl)-2-(3-(quinolin-2-yl)phenoxy)-9H-carbazole (PtON11Me), yielded high external quantum efficiencies and high operational lifetimes. A maximum EQE of 12.5% and color coordinates CIE (x = 0.61, y = 0.36) was achieved in devices employing efficient hole blocking and transporting materials and a high operational lifetime of T_0.97 ∼ 3200 h was achieved in devices utilizing electrochemically stable hole blocking and transporting materials.     

Ethoxylated polyethylenimine as an efficient electron injection layer for conventional and inverted polymer light emitting diodes

We report inverted light emitting devices using ethoxylated polyethylenimine (PEIE) as a single electron injection layer for indium tin oxide cathode, which possess comparable efficiency to those using ZnO/PEIE double electron injection layers. Implementation of a PEIE layer between light emitting polymer layer and aluminum has been shown to significantly enhance device efficiency as well. Improvement of device efficiency can be attributed to increased electron injection due to the reduced work function of PEIE modified cathode as well as the hole blocking effect of PEIE layer. Furthermore, PEIE serves as an efficient electron injector for a range of light emitting polymers with wide distribution of energy levels.     

Boosting the performance of solution-processed quantum dots light-emitting diodes by a hybrid emissive layer via doping small molecule hole transport materials into quantum dots

Solution-processed colloidal quantum dot light-emitting diodes (QLED) have attracted many attentions with significant progress in recent years. However, QLED devices still face some challenges. The energy barrier between Cd-base quantum dots (QDs) and commonly used hole transport materials is larger than that between QDs and electron transport materials, which leads to the imbalance of carriers in the light emitting layer (EML) and the low performance of QLED devices. Herein, we report a simple strategy to improve the device performance by doping small molecule transport material 4,4′-cyclohexylidenebis[N,N-bis(p-tolyl)aniline] (TAPC) into red CdSe/ZnS QDs. The optimized red QLED devices with TAPC-doped emissive layer at a ratio of 3.2 wt% achieve 20.0 cd/A of maximum current efficiency, 16.6 lm/W of power efficiency and 15.7% of external quantum efficiency, which is 30%, 58% and 33% higher than the control device. The improved performance of devices can be ascribed to the increase of hole current density, decrease of leakage electrons and more balanced quantity of carriers in EML. This work put forward a viewpoint to improve the performance of QLED devices via doping high hole mobility materials into emission layer.     

ZnO Nanorod Arrays as Electron Injection Layers for Efficient Organic Light Emitting Diodes

Nanostructured oxide arrays have received significant attention as charge injection and collection electrodes in numerous optoelectronic devices. Zinc oxide (ZnO) nanorods have received particular interest owing to the ease of fabrication using scalable, solution processes with a high degree of control of rod dimension and density. Here, vertical ZnO nanorods as electron injection layers in organic light emitting diodes are implemented for display and lighting purposes. Implementing nanorods into devices with an emissive polymer, poly(9,9‐dioctyluorene‐alt‐benzothiadiazole) (F8BT) and poly(9,9‐di‐n‐octylfluorene‐alt‐N‐(4‐butylphenyl)dipheny‐lamine) (TFB) as an electron blocking layer, brightness and efficiencies up to 8602 cd m^?2 and 1.66 cd A^?1 are achieved. Simple solution processing methodologies combined with postdeposition thermal processing are highlighted to achieve complete wetting of the nanorod arrays with the emissive polymer. The introduction of TFB to minimize charge leakage and nonradiative exciton decay results in dramatic increases to device yields and provides an insight into the operating mechanism of these devices. It is demonstrated that the detected emission originates from within the polymer layers with no evidence of ZnO band edge or defect emission. The work represents a significant development for the ongoing implementation of ZnO nanorod arrays into efficient light emitting devices.     

Microstructural Control of Charge Transport in Organic Blend Thin‐Film Transistors

The charge‐transport processes in organic p‐channel transistors based on the small‐molecule 2,8‐difluoro‐5,11‐bis(triethylsilylethynyl)anthradithiophene (diF‐TES ADT), the polymer poly(triarylamine)(PTAA) and blends thereof are investigated. In the case of blend films, lateral conductive atomic force microscopy in combination with energy filtered transmission electron microscopy are used to study the evolution of charge transport as a function of blends composition, allowing direct correlation of the film's elemental composition and morphology with hole transport. Low‐temperature transport measurements reveal that optimized blend devices exhibit lower temperature dependence of hole mobility than pristine PTAA devices while also providing a narrower bandgap trap distribution than pristine diF‐TES ADT devices. These combined effects increase the mean hole mobility in optimized blends to 2.4 cm²/Vs – double the value measured for best diF‐TES ADT‐only devices. The bandgap trap distribution in transistors based on different diF‐TES ADT:PTAA blend ratios are compared and the act of blending these semiconductors is seen to reduce the trap distribution width yet increase the average trap energy compared to pristine diF‐TES ADT‐based devices. Our measurements suggest that an average trap energy of <75 meV and a trap distribution of <100 meV is needed to achieve optimum hole mobility in transistors based on diF‐TES ADT:PTAA blends.     

Modulation of ambipolar charge transport characteristics in side-chain polystyrenes as host materials for solution processed OLEDs

A series of side-chain polystyrenes was developed as ambipolar hosts for solution processed organic light emitting diodes (OLEDs). The series was derived from the hole-only transport host molecule 1,3-Bis(N-carbazolyl)benzene (mCP). Electron transport ability was incorporated into the host polymers by the introduction of electron-poor heterocycles (pyridine or triazine) and extending delocalization of the lowest unoccupied molecular orbital (LUMO). The materials were tested in Ir-based green OLED devices with all organic layers processed from solution. Devices with the polymer combining triazine and carbazole on its side-chain exhibited a low luminance on-set voltage of 3.0 V and a current efficacy of 28.9 cd/A, which was more than 10 times higher than for devices with the mCP-based polymer (1.6 cd/A). The increase in performance is most likely due to an improvement of charge balance in the emissive layer, showing that our ambipolar polymers are good candidates for further wet-process optoelectronic applications.     

Vacuum-processed polyethylene as a dielectric for low operating voltage organic field effect transistors

We report on the fabrication and performance of vacuum-processed organic field effect transistors utilizing evaporated low-density polyethylene (LD-PE) as a dielectric layer. With C₆₀ as the organic semiconductor, we demonstrate low operating voltage transistors with field effect mobilities in excess of 4 cm²/Vs. Devices with pentacene showed a mobility of 0.16 cm²/Vs. Devices using tyrian Purple as semiconductor show low-voltage ambipolar operation with equal electron and hole mobilities of ～0.3 cm²/Vs. These devices demonstrate low hysteresis and operational stability over at least several months. Grazing-angle infrared spectroscopy of evaporated thin films shows that the structure of the polyethylene is similar to solution-cast films. We report also on the morphological and dielectric properties of these films. Our experiments demonstrate that polyethylene is a stable dielectric supporting both hole and electron channels.     

Emission from outside of the emission layer in state-of-the-art phosphorescent organic light-emitting diodes

The emission zone profile in an organic light-emitting diode was extracted by fitting the experimentally measured far-field angular electroluminescence spectrum of a purposely designed device. It is based on a thin 10 nm emission layer doped with the red emitting phosphor Ir(MDQ)₂acac. We find strong indications for light emission originating from outside of the emission layer, even though the device has electron and hole blocking layers. These are commonly assumed to completely confine the charge carrier recombination and hence the light emission to the emission layer. Since the calculated internal spectrum of the emission matches the emitter photoluminescence spectrum well, diffusion of the emitter molecules outside of the emission layer is hypothesized.     

Improved ambipolar charge injection in organic field-effect transistors with low cost metal electrode using polymer sorted semiconducting carbon nanotubes

Solution-processed thin film transistors can be implemented using simple and low cost fabrication, and are the best candidates for commercialization due to their application to a range of wearable electronics. We report an ambipolar charge injection interlayer that can improve both hole and electron injection in organic field-effect transistors (OFETs) with inexpensive source-drain electrodes. The solution processed ambipolar injection layer is fabricated by selective dispersion of semiconducting single walled carbon nanotubes using poly(9,9-dioctylfluorene). OFETs with molybdenum (Mo) contacts and interlayer (Mo/interlayer OFETs) exhibit superior performance, including higher hole and electron mobilities, device yield, lower threshold voltages, and lower trap densities than those of bare transistors. While OFETs with Mo contacts show unipolar p-type behaviour, Mo/interlayer OFETs display ambipolar transport due to significant enhancement of electron injection. In the p-type region, transistor performance is comparable to devices with gold (Au). Hole mobility is increased approximately ten-fold over devices with only Mo contacts. The electron mobility of Mo/interlayer OFETs is 0.05 cm²V⁻¹s⁻¹, which is higher than devices with Au electrodes. The p-type contact resistances of Mo/interlayer OFETs are half those of OFETs with Mo contacts. Trap density in Mo/interlayer OFETs is one order magnitude lower than that of pristine devices. We also demonstrate that this approach is extendible to other metals (nickel) and n-type semiconductors with different energy levels. Injection by tunnelling is suggested as the mechanism of ambipolar injection.