首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 125 毫秒
1.
根据子滤波器抽头级联法,采用梳状滤波器作为子滤波器,设计了一种新型FIR数字滤波器.通过C语言编程的方法来选择子滤波器阶数,使原型滤波器的过渡带宽度最宽.采用经过变换的通带和阻带边界频率来进行原型滤波器的设计,使得原型滤波器的阶数比传统实现方法低很多.采用该方法实现的FIR滤波器乘法器个数比传统方法少很多,硬件实现更为简单,大幅减小了硬件开销.该方法已成功用于回声消除和噪声抑制芯片,FIR滤波器的面积约为传统方法的50%,用180 nm 3.3 V/1.8 V 6层金属混合信号CMOS工艺流片,结果表明,对于过渡带较窄的滤波器,该方法非常有效.  相似文献   

2.
王小华  何怡刚 《电子学报》2008,36(3):486-489
以频率响应屏蔽(FRM)技术为基础,提出了一种基于神经网络的窄过渡带FIR数字滤波器的优化设计新方法.该算法主要通过使频率响应平方误差函数最小化来获得FRM滤波器系数.文中详细介绍了基于神经网络的基本FRM滤波器和多层FRM滤波器的设计算法及设计步骤,证明了该算法的稳定性定理,给出了仿真实例,并与已有的设计方法进行了比较,设计结果表明用该方法设计的窄过渡带FIR数字滤波器性能更为优越.  相似文献   

3.
FIR滤波器具有绝对稳定性和线性相位的优势,然而当对滤波器的频域性能要求较高时,FIR滤波器通常需要很高的阶数,这使得FIR滤波器硬件执行的复杂度很高。为降低FIR滤波器的硬件执行复杂度,诸多研究者进行了探索。文章对低复杂度FIR滤波器设计方法进行研究,着重介绍比较典型的频率响应罩设计方法、外插脉冲响应设计方法和基于压缩感知的设计方法。  相似文献   

4.
提出了一种设计高效窄过渡带宽FIR滤波器的新方法。该方法以传统的频率响应屏蔽(FRM)方法为基础,通过选择特定的原型滤波器来降低合成的数字FIR滤波器的复杂度。本文研究了该方法的原理、实现结构和设计方法,并通过设计实例证明了此方法的有效性。  相似文献   

5.
荀亮  黄清 《电子工程师》2006,32(12):25-28
介绍了多载波通信中一种设计高效宽带锐截止FIR(有限冲击响应)滤波器的新方法———频障法。通过选择特定的原型滤波器来降低实现宽带锐截止FIR滤波器的复杂度。首先设计一个合适的宽带低通原型FIR滤波器Ha(z),然后得到其互补滤波器Hc(z)。再对它们进行L倍内插,得到两个互补的多带滤波器Ha(zL)、Hc(zL),然后用合适的频障滤波器HMa(z)和HM c(z)分别去消除Ha(zL)、Hc(zL)中不需要的频带,相应的输出加在一起就是所要设计的滤波器H(z)。详细研究了该方法的实现结构和设计方法,并通过设计实例证明了实现同样的性能时频障法比其他方法能节省很大的运算量,因而具有较高的应用价值。  相似文献   

6.
声像距离控制是实现三维视听系统的关键技术之一.现有的音频环绕声技术产生的声像距离固定,且扬声器环形结构不利于与视听系统融合.针对上述问题,本文提出一种利用线型扬声器阵列通过二维FIR滤波器控制声像距离的方法.首先根据声波的传播特点,通过调整声源到波前的时间延迟,改变波前半径产生了虚拟声像.将时间延迟作为二维FIR滤波器的群延迟,使滤波器具有线性相位.考虑到宽带信号,设计具有楔形过渡带的滤波器幅频响应,使在期望宽度内形成波束.最后给出了滤波器实现步骤以及仿真结果.实验表明利用二维FIR滤波器在线型扬声器阵列中实现了声像距离的控制,输出稳定的波束.该方法改变了声像的距离,增强了沉浸感,线型扬声器更容易与视听系统相结合.  相似文献   

7.
直放站回波消除器中数字抗混频滤波器的设计   总被引:1,自引:0,他引:1  
就DVB/CMMB数字回波消除直放站研发中涉及的抗混频数字抽取滤波器这一关键技术进行了详细研究,对3种数字抽取滤波器(FIR,HBF,CIC)进行了简要介绍,对其实际性能进行了对比分析。最后,采用Matlab与FPGA硬件平台相结合的设计方法对性能最合适的FIR滤波器进行硬件实现、联合仿真、测试与验证,该设计方法极大优化了设计进程。  相似文献   

8.
赵晖  陆珺  陆健鲲 《现代雷达》2019,41(1):73-79
射频性能和计算量的平衡是正交频分复用(OFDM)雷达信号得以应用的前提。文中使用一种子载波频谱幅度滚降的OFDM 雷达信号加权系数生成方法,通过调整滚降系数来控制过渡带中的子载波功率,保证低功率峰均比的前提下减少直接数字式频率合成(DDS)中有限长单位冲激响应(FIR)滤波器所需阶数。通过设计低计算复杂度的产生与接收方案,分析了饱和放大器幅度非线性以及模拟滤波器相位非线性对OFDM 雷达信号带来的影响,使其在现有雷达硬件平台上可实现。仿真和测试验证了文中提出方法的有效性。  相似文献   

9.
介绍了一种基于频分复用信号的宽带数字收发设计。根据软件无线电基本理论给出了系统的硬件具体实现和软件处理流程,描述了基于FPGA平台的并行FIR滤波器和并行CIC滤波器的高效实现方法。给出了宽带数字收发系统的仿真和测试结果。该系统硬件结构简洁,逻辑资源开销小,通用性和扩展性强。  相似文献   

10.
遗传算法在FIR滤波器设计——频率抽样法中的应用   总被引:12,自引:0,他引:12       下载免费PDF全文
陈小平  于盛林 《电子学报》2000,28(10):118-120
本文介绍了遗传算法在FIR滤波器设计——频率抽样法中的应用.用遗传算法确定过渡带样本值,解决了传统方法(查表法)不能保证数据是最优的问题.本文还对标准遗传算法进行了适当的改进.给出了FIR数字低通、带通滤波器设计的两个例子.实验结果说明通过遗传算法设计的FIR滤波器性能较查表法得到了改善.  相似文献   

11.
In the present century, digital signal processing (DSP) approaches are considered to be one of the most powerful technologies which may shape the science and technology in coming decades. From 1970 onwards, a drastic revolution took place in a wider domain of DSP which has made it popular in several studies such as radar and sonar signal processing, digital televisions, wireless communication scenarios and other multimedia setup etc. Digital filters form the backbone of this DSP architecture and in point of fact the field of digital filter design has drawn justified recognition from the researchers throughout the world for the last 50 years. In connection to this, thousands of research articles may be found from the literature which had extensively addressed on the design of such filters. In order to meet the requirement of narrow transition-band, finite impulse response (FIR) filters are commonly assumed to be of higher order and accordingly it significantly enhances computational complexity. In regard to this, construction of hardware efficient digital filters had drawn significant consideration which aims to include minimum hardware elements during its application and consequently consumes less power. This review paper illustrates various techniques for the implementation of hardware efficient narrow transition-band FIR filter and investigates a number of favourable attributes which are capable in sustaining the stringent requirements of communication standards. A good number of relevant articles are taken from the literature so as to make a robust and complete review.  相似文献   

12.
A very efficient technique to drastically reduce the number of multipliers and adders in narrow transition-band linear-phase finite-impulse response digital filters is to use the one-stage or multistage frequency-response masking (FRM) approach, which has been originally introduced by Lim and further improved by Lim and Lian. In these original synthesis techniques, the subfilters in the overall implementation are separately designed. As shown earlier by the authors of this contribution together with Johansson, the arithmetic complexity in one-stage FRM filter designs can be considerably reduced by using the following two-step technique for simultaneously optimizing all the subfilters. First, a suboptimal solution is found by using a simple design scheme. Second, this solution is used as a start-up solution for further optimization, which is carried out with the aid of an efficient nonlinear optimization algorithm. This paper exploits this approach to synthesizing multistage FRM filters. An example taken from the literature illustrates that both the number of multipliers and the number of adders for the resulting optimized multistage FRM filters are approximately 70 percent compared with those of the filters synthesized using the original multistage FRM filter design schemes. Additional examples are included in order to show the benefits provided by the proposed synthesis scheme over other recently published design techniques, in terms of an improved performance of the resulting solution, a higher accuracy of the solution, and a faster speed required to arrive at the best solution.  相似文献   

13.
High computational complexity is a major problem encountered in the optimal design of two-dimensional (2-D) finite impulse response (FIR) filters. In this paper, we present an iterative matrix solution with very low complexity to the weighted least square (WLS) design of 2-D quadrantally symmetric FIR filters with two-valued weighting functions. Firstly, a necessary and sufficient condition for the WLS design of 2-D quadrantally symmetric filters with general nonnegative weighting functions is obtained. Then, based on this optimality condition, a novel iterative algorithm is derived for the WLS design problem with a two-valued weighting function. Because the filter parameters are arranged in their natural 2-D form and the transition band is not sampled, the computation amount of the proposed algorithm is reduced significantly, especially for high-order filters. The exponential convergence of the algorithm is established, and its computational complexity is estimated. Design examples demonstrating the convergence rate and solution accuracy of the algorithm, as well as the relation between the iteration number of the algorithm and the size and transition-band width of the filter are given.  相似文献   

14.
In this paper, we present several new properties of the recently introduced interleaved DFT modulated filter bank and an efficient algorithm for designing the filter bank. The periodicity and symmetry properties of the overall transfer function and aliasing transfer functions are stated. Then the design of the filter bank is formulated into a constrained optimization problem that jointly minimizes the overall distortion and aliasing distortion subject to fixed bounds on the stopband energy, transition-band energy, and passband flatness of the prototype filters. The constrained optimization problem is solved by the 2block Gauss-Seidel method, which alternatively optimizes the analysis PF pair and the synthesis PF pair. Since the overall distortion and aliasing distortion are jointly minimized, the proposed algorithm can lead to filter banks with small reconstruction error, even when the filter banks behave with a low redundancy ratio and short PFs. The convergence of the proposed algorithm is proved. Numerical examples and comparisons with the existing method are included to demonstrate the performance of the proposed algorithm.  相似文献   

15.
A very efficient technique for drastically reducing the number of multipliers and adders in narrow transition-band linear-phase finite impulse response (FIR) filters is to use the one-stage or multistage frequency-response masking (FRM) approach as originally introduced by Lim. In the original synthesis techniques developed by Lim and Lian, the subfilters in the overall approach were designed using time-consuming linear programming. In order to perform the overall synthesis faster, this paper shows how these subfilters can be designed with the aid of the the Remez multiple exchange algorithm, the most powerful technique for designing arbitrary-magnitude linear-phase FIR filters in the minimax sense. In addition to speeding up the overall procedure, the use of the Remez algorithm enables one to generate a very fast MATLAB program for the overall synthesis so that after being given the filter specifications as well as the number of stages, the program automatically provides the solution with the minimum number of multipliers and adders required in the overall implementation. This is possible because the MATLAB Remez routine is directly available and thus can be used for this purpose after appropriate modifications.  相似文献   

16.
Decimation and interpolation are very common multirate signal processing operations. Conventional decimation or interpolation technique using polyphase filters has the advantage that for a given transition-band sharpness, the filter's computational complexity decreases with increasing interpolation or decimation factor. Nevertheless, if the transition band of the decimation or interpolation filter is very sharp, the complexity of the filter may still be very high. The complexity of a very sharp filter may be reduced using the frequency-response masking (FRM) technique. However, as shown in this paper, for a given transition-band sharpness, the computational complexity of the classical FRM method does not reduce as rapidly as the increase in decimation or interpolation factor. In this paper, we present a novel variant of the FRM technique for interpolation or decimation application. In this new variant, the computational complexity reduces as rapidly as the interpolation or decimation factor increases. The reduction in computational complexity increases with decreasing transition width. Over an order of magnitude reduction in computational complexity is achieved when compared with conventional polyphase approach in a particular example presented in this paper.  相似文献   

17.
In this paper, we propose a new approach for optimization based stable linear-phase infinite impulse response (IIR) perfect reconstruction quadrature mirror filter (PRQMF) bank design. To this end, the design problem is formulated using stop-band energy, stability, transition-band, pass-band and stop-band ripples requirements as constraints. Lagrange multiplier method is used for the solution of optimization-based design problem. The brief conclusion with design example that illustrates the proposed design method is presented.  相似文献   

18.
Direct-coupled resonator filters in transmission line are discussed. The resonators consist of sections of transmission line coupled either by series capacitances or shunt inductances. Over narrow frequency bands, such filters show characteristics similar to those of lumped-constant filters and their design is straightforward. The design of direct-coupled resonator filters over wide (as well as narrow) frequency bands is presented here using the quarter-wave transformer as a prototype circuit. Several numerical examples (with fractional bandwidths between 10 per cent and 85 per cent) are worked out to illustrate the method. It is shown that the response can be improved by optimizing the line impedances.  相似文献   

19.
This paper preaents simplified lumped-type equivalent representations, which are equivalent to multiwire lines in the vicinity of a quarter-wavelength frequency. It is believed that the derived representation can easily be applied to the analysis and the design of coupled-line filters and directional couplers of narrow bandwidths composed of quarter-wavelength strips. In this paper, the general design methad for coupled-line bandpass filters is presented as one of the applications. A new bandpass filter is proposed and the design formulas of the filter are derived by using the design method. Furthermore the range of validity of the derived representations has been checked by showing numerical design examples. They have been found to give excellent results for coupled-line filters of bandwidths up to about 30 percent.  相似文献   

20.
A method based on equivalent circuit and transmission line model is proposed to design narrow bandpass grid filters in short millimeter wave. Several bandpass filters with 2, 3 or 4 element inductive wire grids in the 70GHz region have been designed with Butterworth or Chebyshev characteristic for linear polarized wave. The agreement between measurement and design theory is good and this proves the rationality and practicality of our design theory.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号