共查询到19条相似文献,搜索用时 406 毫秒
1.
2.
针对碳纤维复合材料构件界面脱粘缺陷,采用调制激励红外热波技术进行了无损检测。在分析调制激励红外热波检测技术基本原理的基础上,搭建了卤素灯激励红外热波检测系统,并进行了系统的检测试验;对碳纤维复合材料构件表面热波信号进行傅里叶变换,获得红外图像序列对应的幅值图,有效改善了特征图像的信噪比;分析了采样频率、光源输出功率和调制频率对幅值对比度的影响规律。 相似文献
3.
对红外热成像技术的特点、原理进行了阐述,提供了电气设备内外部热故障诊断的理论方法,提出了检测时注意要求,保证检测工作安全有效地进行。通过对井下电气设备检测的实际应用,验证了红外热成像技术的高效性、可靠性。 相似文献
4.
5.
6.
7.
8.
9.
10.
针对带式输送机输送带纵向撕裂检测装置不可靠的技术状态,分析了输送带纵向撕裂检测的各种技术和方法。针对检测输送带纵向撕裂的单一技术方法,如红外热成像法、光纤测温法、电机功率与电机电流组合法等各种方法。采用层次分析法对几种检测技术进行了性能比较分析,最终提出了依靠3种检测方法相结合来提高输送带纵向撕裂检测可靠性的技术方案。 相似文献
11.
12.
13.
Today, the Waelz process using a rotary kiln is the best technology available for the pyro-metallurgical treatment of zinc-bearing residues. However, this process will only result in a good zinc recovery, if the temperature distribution in the kiln and the rheological behavior of the material are controlled. Unfortunately, these properties cannot be measured with conventional sensors. In this paper, an image processing system for the Waelz kiln process will be presented, which calculates the relevant process information from infrared camera images in an online manner. It uses a custom-built infrared camera with a spectral filter at 3.9 μm, which provides for a detailed insight into the kiln. The information that is calculated by the image processing system, including temperature distributions of the material, repose and filling angles, is directly used for closed loop control. The system presented has been in operation at an industrial plant in Germany for about 2 years. 相似文献
14.
遥感-岩石力学的试验研究表明,岩石在受力与灾变过程中存在特征性的红外辐射变化,利用红外手段可以监测岩石应力与灾变问题。在过去遥感-岩石力学试验研究的基础上,针对矿山与岩石破裂失稳有关的安全隐患问题,利用红外热像仪对河北省峪耳崖金矿和辽宁省齐大山铁矿进行了现场检测,结果表明,利用热像仪可以检测井下高矿压部位、冒落和片帮等危险性的部位、渗水部位以及露天矿中断层和滑坡危险区,这些区域在热像中呈现不同于周围正常岩石的温度色调。如果结合长时间动态观测,可以对这些矿山灾害进行预测预警。研究结果为矿山安全及防灾减灾提供了新的监测预警手段。 相似文献
15.
通过对个旧矿区龙树脚含矿断裂带(Ⅱ-11#含矿断裂带)构造地质特征的分析,探讨了矿区断裂构造的形成机理,即地层的构造运动及成矿物质的沉淀、搬运等物理过程,认为龙树脚含矿断裂带的成矿部位主要集中于断裂挟持带、断裂与互层(地层)交切部位、断裂扎根部位、断裂分支复合部位以及断裂转折端部位。在此基础上,进一步分析认为金属元素分带、构造、围岩蚀变、化探原生晕等矿区有利找矿标志;断裂与互层交切部位、断裂转折端、断裂交汇(切)锐角挟持带、断裂带分支复合部位为矿区有利的找矿部位。 相似文献
16.
17.
Carina Maria Schl?gl 《BHM Berg- und Hüttenm?nnische Monatshefte》2012,157(8-9):313-318
The roll cladding-process enables the combination of material properties of aluminium and magnesium. This paper focuses on the development of a material compound of Mg(AZ31) and Al(1050). Sensitivity analyses, in combination with special testing methods, make it possible to find optimal manufacturing parameters. With attention to prospective applications of the compound, mechanical values and thermomechanical characterisation using a Gleeble-3800-system were additionally performed. The important interface zone between the metal multilayers was analysed systematically by scanning electron microscope (SEM) and micro hardness testing. Based on this information important conclusions about the hot forming process and the thermal treatments can be derived. 相似文献
18.
利用傅里叶变换红外光谱仪对新疆水西沟煤田火区自然地物进行发射率光谱测量,采用平滑光谱迭代法对温度和发射率进行分离反演,得到精确的地物温度和发射率,对7种典型自然地物热红外发射率光谱特征进行分析,并选择ASTER影像5个热红外波段进行数据模拟。结果表明:① 波长在8~13 μm,地物热红外发射率光谱特征存在明显差异,尤其是在8.5~10.0,11.3和12~13 μm处,可作为识别不同地物的特征波段;② 发射率光谱在ASTER影像5个热红外波段变化趋势呈现明显区别,在遥感影像对火区地物信息的提取研究中具有实际应用价值;③ 得到的地物发射率为火区地表温度的反演提供了精确的参数,可以提高温度反演的精度。 相似文献