共查询到20条相似文献,搜索用时 78 毫秒
1.
2.
Nb对C-Si-Mn-Cr双相钢相变规律、组织和性能的影响 总被引:4,自引:0,他引:4
根据C-Si-Mn-Cr和C-Si-Mn-Cr-Nb实验钢的相变规律,在实验窒进行了控轧控冷实验研究,分析了微合金元素Nb对高强度热轧舣相钢相变规律、组织和性能的影响.实验结果表明,Nb可显著推迟铁索体和珠光体转变,并显著降低铁素体丌始转变温度,但对铁素体终止转变温度和贝氏体转变温度区间基本没有影响.经Nb微合金化后,实验钢的屈服强度和抗拉强度增幅均在100 MPa以上,屈服强度的增幅高于抗拉强度,且在强度大幅度升高的同时,伸长率下降并不明显,表明Nb的细晶强化作用对提高中温卷取热轧双相钢强度级别的效果明显. 相似文献
3.
采用全自动相变仪、扫描电子显微镜、电子万能拉伸试验机、宏观硬度计等设备和Thermo-Calc热力学计算软件研究了3种1 500 MPa级不同Al元素含量对马氏体超高强钢的相变行为、显微组织和力学性能的影响规律。结果表明,相对于不含Al实验钢,Al质量分数为3%实验钢的Ac1温度提高了24℃,Al质量分数为1.5%实验钢的Ac3温度提高了99.8℃,并且与不含Al实验钢相比,含3%Al的实验钢密度降低4.15%。随着Al含量的增加,实验钢热轧后直接水冷至室温的组织由单一的板条马氏体转变为马氏体+沿轧向拉长的铁素体两相层状组织。由于固溶强化以及混合法则的影响,马氏体超高强钢的抗拉强度与硬度都随Al含量的增加呈现出先增加后减少的趋势,1.5Al钢轧向抗拉强度达到1 723 MPa,硬度达到530HV,而3Al钢轧向-40℃低温冲击韧性最大可达到363 J。 相似文献
4.
利用热模拟试验机、OM、TEM等试验设备,研究了Ti-Nb微合金化高速护栏钢的连续冷却组织转变规律,建立了试验钢的CCT曲线。研究结果表明:当冷速为0.5℃/s时,试验钢中的奥氏体发生铁素体-珠光体相变;当冷速大于1℃/s时,开始发生贝氏体相变;当冷速为10~20℃/s时,既发生铁素体-贝氏体相变又发生马氏体相变;当冷速≥30℃/s时,发生贝氏体-马氏体的相变。随着冷速的增加,试验钢的硬度也随之增大。在不同冷速下钢中均存在(Ti, Nb)C析出物,且在钢中呈弥散分布,在低冷速条件下,钢中析出物的体积分数较大,尺寸较小,具有一定的析出强化效果。 相似文献
5.
6.
7.
采用SiMnTiNb低C钢成分、运用TMCP技术在1 450mm热连轧生产线上成功开发了一种屈服强度700MPa级热轧超高强冷成形用钢。测定了开发钢的连续冷却相变(CCT)曲线,研究了其析出强化规律,测试了带钢的力学性能和冷弯性能,研究了其焊接性能。结果表明,其组织为4~5μm细晶粒铁素体+贝氏体+少量马氏体,铁素体晶粒中含Nb-Ti沉淀相。超高强度的获得归功于细晶强化+相变强化+析出强化。所开发的热带钢冷弯成形性和焊接性能良好。 相似文献
8.
超高强度马氏体时效钢的发展 总被引:11,自引:3,他引:11
马氏体时效钢是以无碳(或超低碳)铁镍马氏体为基体的经时效生产金属间化合物沉淀硬化的超高强度钢。该钢在高强度时效处理前具有良好的成形性,时效处理几乎不变形,时效处理后有高强韧性。文中论述了典型Ni-Co-Mo-Ti-Al马氏体时效钢和Ni-Mo-Ti(-Cr-Al)无钴马氏体时效钢的化学成分和力学性能,阐述了马氏体时效钢在400~500℃时效时马氏体基体内产生大量强化效果极高、韧性损失极小的金属间化合物沉淀相的时效结构和强化机制,以及Ni、Co、Mo、Cr、Mn、Ti等元素在马氏体时效钢中的合金化作用。概述了马氏体时效钢的生产工艺,应用和发展趋向。 相似文献
9.
10.
11.
12.
B. Ravi Kumar B. Mahato N. R. Bandyopadhyay D. K. Bhattacharya 《Metallurgical and Materials Transactions A》2005,36(11):3165-3174
Stainless steels (SSs) having a stable and metastable austenitic phase were studied to see the influence of strain-induced
phase transformation in the metastable austenitic stainless steel on the evolution of texture during cold rolling and aging.
AISI 304L and 316L SS plates were unidirectionally cold rolled up to a 90 pct reduction and aged at different aging temperatures.
The strain-induced transformation of austenite to α′-martensite phase and the evolution of texture in both the phases were studied as a function of rolling reduction as well
as aging temperature in the metastable 304L austenitic stainless steel. The X-ray diffraction (XRD) technique was employed
to quantify the volume fractions and characterize the texture of austenite and martensite phases in the rolled and aged conditions.
Results are compared with the texture evolution in the stable austenitic 316L SS. 相似文献
13.
14.
Finite Element Simulation of Hot Strip Continuous Rolling Process Coupling Microstructural Evolution 总被引:2,自引:0,他引:2
Using the nonlinear rigid viscoplastic finite element method (FEM), a finite element simulation of the hot strip continuous rolling process was done, which completely integrates different phenomena such as the metallurgical behavior of the strip and the thermo mechanics in the strip based on the physical metallurgical microstructural evolution law. By combining with the process parameters of certain 2 050 mm hot strip rolling, an actual rolling process of low carbon steel SS400 was simulated using the FEM model. Based on the simulation results, the distributions of the strain field, the temperature field, and the microstructure were presented. Meanwhile, the simulated rolling force, temperature, and microstructure are in good agreement with the measured results. 相似文献
15.
Many researches[1 -6]about the grain refinementandthe development of supersteels have been carriedout , and some achievements have been made . InChina ,the 400 MPa supersteel strips with about 5μm grain size have been produced industrially andthe products have been applied to manufacture thebeams of automobiles . Having high strength, goodductility and suitable yield/tensile strength ratio ,the supersteel strips have good formability and aresuitable for stamping. Althoughthe fatigue properti… 相似文献
16.
17.
超细晶粒钢及其力学性能特征 总被引:6,自引:0,他引:6
探索了在新一代钢中获得超细晶粒的方法。通过低温轧制和应变诱导铁素体相变,可以在碳素结构钢中获得晶粒尺寸小于5μm的超细晶粒,屈服强度大于400MPa。采用应变诱导铁素体相变可以在微合金钢中得到晶粒尺寸为1μm的超细晶粒。低碳微合金钢的屈服强度达到了600MPa,超低碳微合金钢的屈服强度超过了800MPa。采用微合金化和循环热处理可以在合金结构钢中获得2μm的奥氏体晶粒,1500MPa级抗拉强度下改善了耐延迟断裂性能。 相似文献
18.
通对SS400钢的特点分析,编制了SS400钢生产技术管理规定来指导生产,满足了SS400钢的质量要求,实现了SS400钢板的大批量出口而无质量异议,取得比较显著的经济效益. 相似文献
19.
20.
连铸坯下线至加热炉的温度制度及其表层组织演变与热送或粗轧裂纹密切相关.基于热模拟实验分析了送装工艺对奥氏体转变特征和再加热晶粒尺寸的影响.高温共聚焦激光扫描显微镜原位观察表明,含Nb J55钢在双相区700℃热装时,组织为晶界膜状先共析铁素体、魏氏体和大量残留奥氏体,再加热至1200℃,奥氏体晶粒大小、位置都不变;单相区600℃温装时,组织为大量铁素体+珠光体,再加热至1200℃时,奥氏体晶粒明显细化.马弗炉模拟SS400钢双相区不同热装温度发现,铁素体转变量至少达70%时才可细化再加热后的奥氏体晶粒.在临界转变量以上,基体中铁素体转变量越多晶粒细化程度越明显. 相似文献