共查询到20条相似文献,搜索用时 46 毫秒
1.
研究了马氏体时效钢00Nil4Cr3M03Ti(%:0.002C、14.06Ni、3.19Cr、3.06Mo、1.32Ti)750~1050℃固溶处理的组织和力学性能。结果表明,≤900℃固溶处理,该钢奥氏体晶粒和强度无明显变化,固溶温度超过900℃时钢的奥氏体晶粒显著增大,钢的强度呈下降趋势。当固溶温度由750℃增加至900℃时,随固溶处理温度提高,钢中Fe2Mo相量降低,810℃时完全溶解,钢的冲击功由32J提高至61J,当固溶温度由900℃增至1050℃,随奥氏体晶粒增大,钢的冲击功由61J降至26J。 相似文献
2.
3.
冷轧和固溶处理对改进型202不锈钢组织和力学性能的影响 总被引:1,自引:0,他引:1
研究总冷轧变形量12.5%~46.4%和900~1150℃固溶处理对成分(%)为:0.04C,8.18Mn,15-21Cr,4.05Ni,1.65Cu,0.12N的改进型202亚稳奥氏体不锈钢3mm板组织和性能的影响。结果表明,经总变形量46.4%冷轧后,形变诱发产生约26%α’马氏体,该钢的强度达1200MPa;固溶处理使a'马氏体发生逆转变(a’→γ),900℃固溶可使α’马氏体完全转变成γ奥氏体并完成全部再结晶;改进型不锈钢经900~1100℃固溶处理具有预期的组织和良好的综合力学性能。 相似文献
4.
试验研究了 1040 ℃固溶的马氏体沉淀硬化不锈钢05Cr17Ni4Cu4Nb在480~620 ℃时效5 h的组织,强度和硬度。结果表明,随时效温度升高,马氏体基体逐渐分解,碳化物析岀而降低;在时效处理过程中,随时效温度升高,富Cu相最初以球形析出,逐渐发展成椭圆形及杆状,尺寸增大,与基体共格界面消失,强化效果减弱;05Cr17Ni4Cu4Nb钢经1040 °C固溶,480 °C 5h时效后,其HRC硬度值44.3,满足钢材HRC硬度值43的要求。 相似文献
5.
银对18-8铬镍奥氏体不锈钢抗菌性能的影响 总被引:4,自引:0,他引:4
由ZG-25真空感应炉熔炼成的含银18-8不锈钢0.16C-17.63Cr-8.65Ni-0.27Ag与普通18-8不锈钢0.07C-17.80Cr-7.92Ni的性能对比试验表明,18-8 Ag奥氏体不锈钢的机械性能与普通18-8奥氏体不锈钢相当;普通18-8钢没有明显的抗菌性能,而18-8Ag钢在1050℃固溶处理600℃时效4h后因组织中含有富银相,其抗菌性能显著提高,经粘结薄膜法测定得出18-8-0.27Ag奥氏体不锈钢对大肠杆菌的抗菌率大于93%。对金黄色葡萄球菌的抗菌率为100%。 相似文献
6.
《特殊钢》2016,(4)
采用动电位极化曲线、均匀腐蚀全浸试验研究了50 kg真空感应炉冶炼的00Cr13Ni7Co5Mo4W马氏体时效不锈钢(/%:0.007C,13.23Cr,7.02 Ni,5.06Co,3.72Mo,0.96W)1100℃1 h固溶,450~510℃8 h时效后的耐蚀性能,通过金相显微镜、透射电镜、XRD分析了马氏体时效不锈钢的组织。结果表明,随时效温度升高时效过程析出R相增加,导致钢的耐点腐蚀性下降,同时由马氏体逆转变的奥氏体数量增加,可改善该钢的耐腐蚀性能。00Cr13Ni7Co5Mo4W马氏体时效不锈钢适宜的热处理工艺为1100℃1 h固溶+470℃8 h时效,其年腐蚀速率为1.259 0μm/a,点蚀击穿电位为252 mV。 相似文献
7.
8.
9.
10.
11.
Dy^3+在(LaO)3BO3和(GdO)3BO3中的光致发光 总被引:1,自引:1,他引:0
研究了Dy^3+在(LaO)3BO3和(GdO)3BO3中的光致发光;探讨了基质晶体结构、稀土离子RE^3+的电荷半径比(Z/r)和Dy^3+含量对(Dy^3+)发光强度及发光颜色的影响;分析了(GdO)3BO3中Bi^3+对Dy^3+发光的敏化作用及Dy^3+4F9/2→^6H13/2超灵敏跃迁发射的自身浓度猝灭机理。 相似文献
12.
以碳酸盐为沉淀剂,采用共沉淀法合成Ni1/3Co1/3Mn1/3CO3前驱体,再按照一定的锂配比将其烧结合成层状Li(Ni1/3Co1/3Mn1/3)O2。通过SEM及电性能测试仪等方法,研究了碳酸盐前驱体的合成条件,考察了碳酸盐前驱体的振实密度与合成时pH值、溶液浓度以及反应时间的关系。经过实验分析,在pH=8、溶液浓度C=2mol.L^-1、反应时间t=12-13h时,合成的碳酸盐前驱体Ni1/3Co1/3Mn1/3CO3振实密度达到最高值0.98g.cm^-3。 相似文献
13.
14.
15.
Ca3La(BO3)3中Dy3+的光致发光 总被引:2,自引:0,他引:2
研究了Ca3La(BO3)3基质中Dy^3 的发射光谱和激发光谱。结果表明,强的激发峰值为351nm、367nm和386nm;Dy^3 的488nm和578nm发射的最佳浓度均为xDy=0.03;Dy^3 发射的黄光和蓝光强度比(用Y/B表示)随Dy^3 浓度的增加而逐渐增大;Dy^3 的^4F9/2→^6H15/2、^6H13/2跃迁发射的浓度猝灭机理均为电偶极-电偶极相互作用;同时还探讨了Ce^3 对Dy^3 发光的敏化作用。 相似文献
16.
Dy3 isanimportantactivator .Ithasbeenexten sivelyappliedinmanyluminescentmaterials .Inre centyears ,someresearchershavestudiedthespec trumcharacteristicsofluminescentmaterialsdopedDy3 [1~ 6 ] andhaveobtainedsomemeaningfulre sults .InordertodevelopnewfluorescentmaterialsanddiscussthephotoluminescentruleofDy3 inthecomplexborate ,thispaperstudiesthephotolumines centcharacteristicsofDy3 inBa3La(BO3) 3host ,anddiscussestheinfluenceofthecharge to radiusratio(z/r)ofrareearthionRE3 andthecon… 相似文献
17.
研究了转速,球磨时间等球磨工艺对3Y2O3-5Al2O3机械合金化过程的影响。结果表明:在较低的转速下(250r/min),提供的球磨能量很低,只会细化粉体颗粒;提高转速(400r/min),会促使Y2O3发生晶型转变,由稳定的立方晶转变成非稳态的单斜晶;继续提高转速(500r/min),还会使混合粉体发生合成反应,生成YAlO3(YAP)。在转速为500r/min,球料比为20∶1的球磨条件下,3Y2O3-5Al2O3粉体发生固相反应的过程可分为两个阶段:第一阶段,Al2O3颗粒晶格畸变,快速细化;同时,高能球磨促使Y2O3发生了晶型转变。第二阶段,Y2O3晶型转变基本完成,并呈无定形化,Y2O3和Al2O3发生合成反应,生成YAlO3(YAP)。但在球磨条件下,难以合成Y3Al5O12(YAG)、Y4Al2O9(YAM)。 相似文献
18.
Luminescent material Ba3Gd(BO3)3 doped with Eu3+ ion was prepared by high temperature solid-state method. The preparing conditions, luminescent properties, and particle morphology of Ba3Gd(BO3)3:Eu3 + phosphor were studied with X-ray diffraction (XRD), fluorescence spectroscopy, and scanning electron microscopy (SEM). The results obtained by XRD showed that pure phase of Ba3Gd(BO3)3 was obtained at 1000℃. Images from SEM displayed that the particles of Ba3Gd(BO3)3:Eu3+ phosphor had a spherical shape with an average diameter of about 200-400 nm. The luminescence spectra showed that Ba3Gd(BO3)3:Eu3+ phosphor was effectively excited by the near ultraviolet (UV) light (396 nm) and blue light (466 nm). The main emission peaks of Ba3Gd(BO3)3:Eu3+ phosphor were assigned to the supersensitive transition 5D0-7F2 (611 and 616 nm) of Eu3+ ion when samples were excited at 255 and 396 nm, respectively, and the luminescent intensity of Ba3Gd(BO3)3:Eu3+ at 611 and 616 nm reached to the maximum when the doped content of Eu3+ ion was 10mol.%. Therefore, this phosphor could be a promising red component for possible applications in the field of white LED. 相似文献
19.
CaTiO_3∶Pr~(3 )的合成及发光性质 总被引:2,自引:0,他引:2
报道了稀土离子Pr3+激活的CaTiO3发光材料的合成方法,CaTiO3∶Pr3+位于613nm发射与Pr3+离子1D23H4光谱发射相一致。讨论了不同合成条件对CaTiO3∶Pr3+发光性质的影响 相似文献
20.
田莲花 《中国稀土学报(英文版)》2010,28(1):37-39
The photoluminescence(PL) properties of Ca4YO(BO3)3 doped with Bi3+,Dy3+,and Pr3+ ions were investigated.These compounds were prepared using a typical solid-state reaction.The excitation and emission spectra were measured using a spectrofluorometer.For Ca4YO(BO3)3:Bi3+,the excitation spectrum showed the bands at about 228,309,and 370 nm which correspond to the 1S0→1P1 transition and the 1S0→3P1 transition of Bi3+ ions.The emission band at 390 nm corresponded to the 3P1→1S0 transition of Bi3+ ions.For Ca4YO(BO3)3:Bi3+,Dy3+,energy transfer occurred from Bi3+ to Dy3+ somewhat.In Ca4YO(BO3)3:Bi3+,Dy3+,Pr3+,the excitation band at 367 nm was enhanced obviously due to the energy migration from Bi3+ to Pr3+,which converted efficiently the emission of semiconductor InGaN based light-emitting diode(LED).Therefore,the emission of Dy3+ ions was enhanced due to the energy migration from the process of Bi3+→Pr3+→Dy3+.It resulted in the good color rendering. 相似文献