首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 125 毫秒
1.
王龙锋  李敏 《冶金动力》2011,1(4):25-26,29
介绍了高分子复合波纹膨胀节的耐煤气腐蚀机理、优异性能,从根本上解决了目前316L、800镍基合金、超级奥氏体不锈钢等金属补偿器无法解决的晶界腐蚀问题。  相似文献   

2.
6.4 氯化物和其它含卤离子水溶液介质 ①点蚀和缝隙腐蚀 在高性能不锈钢开发的诸多商业和技术上的决定因素中,最有效的因素莫过于需要在腐蚀性的氯化物介质中具有良好耐点蚀、缝隙腐蚀和应力腐蚀断裂的钢种。因此,高性能不锈钢总的来说比标准不锈钢耐氯化物腐蚀的性能更好。这一良好性能的获得是由于采用了合金元素铬、钼以及氮,所有这些元素在提高耐点蚀和缝隙腐蚀能力方面都非常有效,并且采用高镍和氮来提高耐应力腐蚀断裂性能。  相似文献   

3.
这种超级奥氏体不锈钢在较宽的氯离子浓度范围内都具有高的耐腐蚀性。高氮含量赋予它比6Mo系列的超级奥氏体不锈钢更高的强度和更好的显微组织稳定性(能够防止σ相的形成)。它具有非常高的耐孔蚀及耐缝隙腐蚀性能,在多种介质中具有卓越的耐一般腐蚀性能,与传统不锈钢相比力学性能更高,  相似文献   

4.
445M铁素体不锈钢缝隙腐蚀性能的研究   总被引:1,自引:0,他引:1  
顾玥  詹肇麟  荣凡 《特殊钢》2011,32(3):65-67
研究了445M铁素体不锈钢(%:0.004~0.005C、22.24~22.29Cr、1.10~1.65Mo、0.015~0.016P、0.003~0.004S、0.012~0.016N、0.22~0.38Ti)和316L奥氏体不锈钢(%:0.022C、16.80Cr、10.19Ni、2.02Mo、0.025P、0.001S、0.046N)在40~60℃氯离子浓度(250~5 000)×10-6的氯化钠溶液的缝隙腐蚀性能。结果表明,445M铁素体不锈钢的耐缝隙腐蚀性能优于316L奥氏体不锈钢;当445M钢中的Mo含量由1.10%提高至1.65%时,钢的耐缝隙腐蚀性能明显提高,表明点蚀当量Cr+3.3Mo是衡量不锈钢耐点蚀和耐缝隙腐蚀的重要指标。  相似文献   

5.
近代超级不锈钢的发展   总被引:7,自引:0,他引:7  
罗永赞 《特殊钢》2000,21(4):5-8
不锈钢的近代发展目标是超级不锈钢-超级奥氏体,超级铁素体,超级复相不锈钢。这些钢可在大范围内解决局部腐蚀问题并在某些用途中可替代钛和镍基合金。  相似文献   

6.
双相不锈钢铁素体含量控制及耐腐蚀性能的研究   总被引:3,自引:0,他引:3  
本文简要介绍了双相不锈钢的铁素体和奥氏体两相的控制技术及它的耐腐蚀性能。研究证实,双相不锈钢通过成分和热处理的控制,使得铁素体和奥氏体两相比约为l是可能的,同时它具有优良的耐点腐蚀性能、耐应力腐蚀性能和耐冲刷腐蚀能力;是一种极具成本效益的工程材料。  相似文献   

7.
1前言向不锈钢中添加氮元素可以大大改善不锈钢的机械性能,提高其耐蚀性。添加氮会大大增加不锈钢的强度,而延展性不变。对于固溶强化,氮比碳更为有效,因为氮是一种强奥氏体稳定剂,它可以最大限度的减少奥氏体稳定化处理所需要的镍量,并且提高耐蚀性,特别是耐点蚀和缝隙腐蚀性。因常压下氮在铁水和铁基合金液中的溶解度非常低,所以常压下氮合金化非常困难。在高压氮  相似文献   

8.
1前言 以SUS316L钢为代表的奥氏体不锈钢具有高力学强度和优良的耐蚀性能,在工业材料、民用品、生物材料中得到了广泛的应用。但是,现有奥氏体不锈钢依然容易发生缝隙腐蚀和孔蚀,希望能进一步改善其耐蚀性。另外,奥氏体不锈钢大多数添加有高浓度的镍,镍有可能引起金属过敏。而且,作为生物植入材料使用时,镍的过敏等长期毒性也引起人们的注意。为了解决这些问题,以1%左右的氮代替镍改善力学强度和耐蚀性的无镍不锈钢,作为生物用金属材料受到关注。  相似文献   

9.
张菽浪 《特钢技术》2005,10(2):23-23
由于铁素体不锈钢能抗应力腐蚀裂纹,加之无镍铁素体不锈钢较为经济,因此上世纪70年代初,铁素体不锈钢的研究与开发得到了较大关注。一般而言,铁素体不锈钢的主要特点是在氯化物介质中不产生应力腐蚀开裂,耐点蚀和缝隙腐蚀性强,但成形性能及焊接性能差,这成为发展铁素体不锈钢的主要障碍。研究结果表明,这些缺点都是出自韧性差,而起因是碳和氮的含量高,如果将这些间隙杂质含量控制在极低水平,  相似文献   

10.
高氮不锈钢     
英国一家公司制成了一种高氮不锈钢.其成分是:铬24%、镍18%、锰6%、铝4.5%、氮10.5%其余为铁。这种中高钼含量和高氮含量的不锈钢,其耐腐蚀性能可与昂贵的镍基合金相比,不仅能耐海水腐蚀,而且在焊拉高温下也具有抗氯化物引起点蚀和穴蚀的能力,另外还不会产生高钼钢的钼偏析现象。其屈服强度和抗拉强度分别不小于425MPa和800MPa。这种新型不锈钢具有厂一泛的用途。高氮不锈钢@李惠萍  相似文献   

11.
In recent years,nitrogen-alloyed stainless steels have been a research hotspot in the field of stainless steel product and technology. Nitrogen-alloyed austenitic stainless steels developed by Baosteel and their applications are introduced. These steels are nitrogen-controlled products 304 N and 316 LN,nitrogen containing economical products BN series and high-nitrogen stainless steel( HNS) series. The results show that the presence of nitrogen can significantly improve the strength and corrosion resistance of steel produced. By nitrogen alloying,economical austenitic stainless steels w ith considerably less nickel than 304 can be obtained; the corrosion resistances of these steels are almost the same as 304. Furthermore,by a scientific approach of nitrogen alloying,high-nitrogen steel of0. 8% nitrogen content is fabricated under the non-pressurized conditions,and the pitting potential of this steel is 1. 0 V. At present,nitrogen-alloyed steels developed by Baosteel are w idely utilized in the manufacture of cryogenic storage containers,transportation containers,and many household w ares.  相似文献   

12.
The purpose of the current study is to develop austenitic nickel-free stainless steels with lower chromium content and higher manganese and nitrogen contents. In order to prevent nickel-induced skin allergy, cobalt, manganese, and nitrogen were used to substitute nickel in the designed steel. Our results demonstrated that manganese content greater than 14 wt pct results in a structure that is in full austenite phase. The manganese content appears to increase the solubility of nitrogen; however, a lower corrosion potential was found in steel with high manganese content. Molybdenum appears to be able to increase the pitting potential. The effects of Cr, Mn, Mo, and N on corrosion behavior of Fe-16Cr-2Co-Mn-Mo-N high nitrogen stainless steels were evaluated with potentiodynamic tests and XPS surface analysis. The results reveal that anodic current and pits formation of the Fe-16Cr-2Co-Mn-Mo-N high nitrogen stainless steels were smaller than those of lower manganese and nitrogen content stainless steel.  相似文献   

13.
采用浸泡失重法和电化学方法研究Ce和W对铁素体不锈钢在含Cl-溶液中耐点蚀性能的影响,并通过恒电位极化法测定不同Ce和W含量的铁素体不锈钢临界点蚀温度(CPT)。结果表明,W和Ce都可显著抑制铁素体不锈钢在FeCl3溶液中的腐蚀溶解,且含W的不锈钢蚀坑坑底有W元素富集。Ce和W的添加提高了不锈钢在5%NaCl溶液中的临界点蚀温度,并且当W的质量分数达到1%时,可以显著增强蚀坑的再钝化能力。添加Ce和W可提高不锈钢的点蚀电位,降低腐蚀电流密度,提高不锈钢的耐点蚀性能。不同成分的铁素体不锈钢在中性氯溶液中都表现出稳定的钝态,而Ce和W的添加可以提高钝化膜的稳定性,扩大钝化区范围。  相似文献   

14.
The effect of solution temperature on pitting resistance of superaustenitic stainless steels 20Cr- 25Ni- 6Mo in concentrated chloride media was studied by potentiodynamic scanning(PDS), chemical immersion test and electrochemical impedance spectroscopy(EIS). The microstructure of the alloy after heat treatment was observed by optical microscope(OM). The results show that with the increase of solution temperature, the secondary phases dissolve in the matrix, the grain grows significantly. The rate of weight loss decreases first, and reaches the minimum at 1200??, and thereafter, it increases with further increasing solution temperature. Meanwhile, the radius of the EIS capacitive loop increases first and then reduces, signifying that the corrosion resistance of the stainless steels is first enhanced and then weakened. The deterioration of the corrosion resistance of the stainless steel is attributed to the presence of secondary phases.  相似文献   

15.
为开发价格昂贵的SUS304奥氏体不锈钢的替代产品,试验研究了不同含量C N和Nb,Ti稳定化对B443系列铁素体不锈钢再结晶组织、力学性能、点蚀电位的影响.试验结果表明,Nb,Ti双稳定化提高了B443铁素体不锈钢的再结晶温度和点蚀电位.在试验室研究基础上,宝钢不锈钢分公司试制了B443NT超低碳氮铁素体不锈钢.该产品不仅具有与SUS304相当的耐腐蚀性能,而且具有优良的深拉伸性能和满意的焊接性能,可用于运输、建筑、厨具等众多行业.  相似文献   

16.
研究了合金元素对双相不锈钢2101耐点蚀性能的影响规律。结果显示,2101系列合金的浸泡点蚀腐蚀速率在1.9~7.0 g/(m^2.h)之间,与304不锈钢在同一数量级;Mo是提高2101系双相不锈钢耐腐蚀性的关键元素,而N对耐腐蚀性的影响不大;点蚀起源和Thermo-Calc计算结果显示2101成分体系中,铁素体相是耐点蚀性较弱相,提高铁素体相耐蚀性是提高合金整体耐蚀性的关键;当Cr含量固定在21.5%时,Mo作为铁素体形成元素将在铁素体相中富集,提高铁素体相的耐点蚀性能,从而提高合金整体耐蚀性。  相似文献   

17.
刘城城  张立峰  任英  张继 《钢铁研究学报》2021,33(10):1040-1051
摘要:首先,总结了3种常用的非金属夹杂物对不锈钢耐点蚀性能影响的研究方法,即原位腐蚀观察、微区电化学法、原子力显微镜。其次,总结了硫化物、氧化物、稀土夹杂物3种不同类型夹杂物对不锈钢耐腐蚀性能影响。随着硫化物含量的增多,不锈钢的耐点蚀性能会下降;对于氧化物的影响,目前的研究集中在氧化物的成分对不锈钢耐点蚀性能的影响。不同成分的夹杂物对不锈钢耐点蚀性能的影响机制还不是很清楚;稀土夹杂物对不锈钢点蚀的影响主要与稀土对不锈钢中夹杂物改性有关。而后,汇总了目前提出的夹杂物对不锈钢耐点蚀性能影响的机制,即贫Cr区机制、微缝隙机制、活性机制。贫Cr区机制主要用于解释硫化物引起的点蚀,后2种主要用于解释氧化物引起的点蚀。最后,提出了夹杂物控制提升不锈钢耐点蚀性能的展望。  相似文献   

18.
The corrosion behaviour of 304LN stainless steels containing three different nitrogen content (0.132, 0.193, 0.406 wt% N) was investigated by potentiodynamic anodic polarization technique, in 1, 4, 6 M nitric acid and simulated high level waste (HLW) medium. The results showed that all three alloys exhibited good corrosion resistance in nitric acid and simulated HLW and the corrosion properties were found to be similar. Owing to the spontaneous formation of the protective chromium oxide passive film in nitric acid and simulated HLW, increasing the nitrogen content of the alloy did not indicate any discernable effect on the corrosion resistance in both media. It was also found that the oxidizing ions present in simulated HLW did not deteriorate the passive film stability of the nitrogen containing alloys. In chloride medium, the highest nitrogen content 304LN stainless steel showed a profound increase in pitting corrosion resistance when compared to the lower nitrogen content alloy. Optical and scanning electron microscopy was carried out to obtain information about the microstructure. The results of the investigation are discussed in the paper.  相似文献   

19.
高氮钢的基础研究及应用进展   总被引:2,自引:0,他引:2  
介绍了高氮钢结构特点的最新研究,高氮钢平衡相图的进展及其在高氮钢成分设计方面的应用;概括了氮在钢液中的溶解度公式和高氮钢熔炼过程中的关键问题;分析了氮在奥氏体钢、铁素体钢和双相不锈钢中的作用,即氮在不牺牲强度的同时不仅提高了钢的韧性,且改善了钢的抗腐蚀性能;并列举了一些典型的高氮钢的用途。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号