Dissolution of reactive strontium-containing alloys in liquid aluminum and A356 melts

The dissolutions of commercial purity strontium and a 90 pct Sr-10 pct Al alloy in liquid aluminum and A356 alloys has been investigated. The dissolutions of these alloys was found to be accompanied by the formation of various intermetallic compounds, the type of which depends on the chemistry and temperature of the melt. Additions at low melt temperatures resulted in the exothermic formation of those intermetallics that have the lowest strontium contents, as seen in the relevant phase diagram,i.e., Al₄Sr in liquid aluminum and SrAl₂Si₂ in liquid A356. Due to low reaction rates at these temperatures, these intermetallics formed as dispersed particles that could easily dissolve in the melt, yielding high recoveries. At high melt temperatures, the associated chemical reactions yielded, as products, the higher strontium intermetallics, which formed with little or no exothermicity. These compounds were observed to be scarcely soluble in the melt, resulting in low recoveries. The dissolution time of these alloys were found to show good agreement with calculated values based on a two-stage model comprising an initial exothermic reaction period and a subsequent free dissolution period. In general, the high-strontium alloys were determined to be efficient at low melt temperatures of 675°C to 700°C. These reactive alloys were observed to form thick surface scales in air, which, in the case of commerical purity strontium, proved to be detrimental to dissolutions because they formed a barrier between the solid and the liquid.     

A study of the influence of mischmetal additions to ai-7si-0.3mg (lm 25/356) alloy

This article deals with the effect of 0.25-1.5 wt pct mischmetal (MM) addition on the mechanical properties, microstructure, electrical conductivity, and fracture behavior of cast Al-7Si-0.3Mg (LM 25/356) alloy. Modification of eutectic silicon by MM is compared with strontium modification in terms of microstructure, mechanical properties, and fading behavior. Loss of magnesium encountered on holding the molten alloy and its resultant effect on mechanical properties of alloys modified with MM and Sr are compared with those in the unmodified alloy.     

Creep and microstructure of magnesium-aluminum-calcium based alloys

This article describes the creep and microstructure of Mg-Al-Ca-based magnesium alloys (designated as ACX alloys, where A stands for aluminum; C for calcium; and X for strontium or silicon) developed for automotive powertrain applications. Important creep parameters, i.e., secondary creep rate and creep strength, for the new alloys are reported. Creep properties of the new alloys are significantly better than those of the AE42 (Mg-4 pct* Al-2 pct RE**) alloy, which is the benchmark creep-resistant magnesium die-casting alloy. Creep mechanisms for different temperature/stress regimes are proposed. A ternary intermetallic phase, (Mg,Al)₂Ca, was identified in the microstructure of the ACX alloys and is proposed to be responsible for the improved creep resistance of the alloys. All concentrations in wt. pct, unless otherwise stated. RE stands for a combination of rare earth elements, i.e., misch metal, in this case.     

On development of press and sinter Al–Ni–Mg powder metallurgy alloys

Abstract

The objective of this research was to initiate the development of powder metallurgy alloys based on the Al–Ni–Mg system. In doing so, binary (Al–Mg) and ternary (Al–Ni–Mg) blends were prepared, compacted and sintered using elemental and master alloy feedstock powders. Research began with fundamental studies on the sintering response of the base aluminium powder with additions of magnesium. This element proved essential to the development of a well sintered microstructure while promoting the formation of a small nodular phase that appeared to be AlN. In Al–Ni–Mg systems a well sintered structure comprised of α aluminium plus NiAl₃ was produced at the higher sintering temperatures investigated. Of these ternary alloys studied, Al–15Ni–1Mg exhibited mechanical properties that were comparable with existing commercial 'press and sinter' alloys. The processing, reaction sintering and tensile properties of this alloy were also found to be reproducible in an industrial production environment.     

Effect of Compositional Variation on the Microstructural Evolution and the Castability of Al–Mg–Si Ternary Alloys

This study examined the microstructural evolution and castability of Al–Mg–Si ternary alloys with varying Si contents. Al–6Mg–xSi alloys (where x = 0, 1, 3, 5, and 7; all compositions in mass pct) were examined, with Al–6 mass pct Mg as a base alloy. The results showed that in the ternary alloys with Si ≤ 3 pct, the solidification process ended with the formation of eutectic α-Al–Mg₂Si phases generated by a univariant reaction. However, in the case of ternary alloys with Si > 3 pct, solidification was completed with the formation of α-Al–Mg₂Si–Si ternary eutectic phases generated by a three-phase invariant reaction. In addition to the eutectic Mg₂Si phases, the primary Mg₂Si phases formed in each of the ternary alloys, and the size of both sets of phases increased with increasing Si content. The two-phase eutectic α-Al–Mg₂Si nucleated from the primary Mg₂Si phases. The inoculated Al–6Mg–1Si alloy had the smallest grain size. Moreover, the grain-refining efficacy of the Al–5Ti–B master alloy in the ternary alloys decreased with increasing Si content in the alloys. Despite the poisoning effect of Si on the potency of TiB₂ compounds in the inoculated Al–6Mg–1Si alloy, the grain size of the alloy was slightly smaller than that of the Al–6Mg binary alloy. This resulted from the increasing growth restriction factor (induced by Si addition) of the Al–6Mg–1Si alloy. In terms of the castability, the examined alloys showed different levels of susceptibility to hot tearing. Among the alloys, the ternary Al–6Mg–5Si alloy exhibited the highest susceptibility to hot tearing, whereas the Al–6Mg–7Si exhibited the lowest. The severity of hot tearing initiated by the unraveling of the bifilm was determined by the freezing range, grain size, and the amount of eutectic phases at the end of the solidification process.

     

Effect of strontium on the microstructure, mechanical properties, and fracture behavior of AZ31 magnesium alloy

The effect of strontium (Sr) on the microstructure, mechanical properties, and fracture behavior of AZ31 magnesium alloy and its sensitivity to cooling rate are investigated. Three phases—blocky-shaped Mg₁₇Al₁₂, acicular Mg₂₀Al₂₀Mn₅Sr, and insular Mg₁₆(Al,Zn)₂Sr—are identified in the Sr-containing AZ31 alloys. With increasing cooling rate, the blocky-shaped Mg₁₇Al₁₂ phase increases, the acicular Mg₂₀Al₂₀Mn₅Sr phase diminishes, and the insular Mg₁₆(Al,Zn)₂Sr phase is refined and granulated. The study suggests that the grain size decreases with increasing cooling rate for a given composition. However, the grain size decreases first, then increases, and finally decreases again with increasing Sr for a given cooling rate. The yield strength (σ _y ) of AZ31 magnesium alloy can be improved by grain refinement and expressed as σ _y =35.88+279.13d ^−1/2 according to the Hall-Petch relationship. The elongation increases when Sr is added up to 0.01 pct and then decreases with increasing Sr addition. Grain refinement changes the fracture behavior from quasicleavage failure for the original AZ31 alloy to mixed features of quasicleavage and microvoid coalescence fracture.     

金属锶及其合金的研究现状与应用

对现有金属锶及其合金(Al-Sr，Mg-Sr，Si-Sr，Cu-Sr，Pb-Sr等合金)的制备技术(真空热还原法、熔盐电解法等)和优缺点、应用现状等进行了分析、比较，并对几种锶合金的相图及合金热力学的研究现状进行了综述。同时指出了我国锶产业发展过程中存在的不足及发展方向。     

Microstructure and Mechanical Properties of Extruded Magnesium-Aluminum-Cerium Alloy Tubes

Current commercial magnesium extrusion alloys do not offer desirable combinations of strength, ductility, and extrusion speed for automotive structural applications. The effect of small additions of cerium (Ce) to pure magnesium (Mg) and Mg-3 pct Al alloy extruded tubes has been studied. The results suggest that 0.2 pct Ce addition can significantly improve the extrudability and mechanical properties of the Mg extrusions. The improvement in mechanical properties is due to grain refinement and dispersion strengthening provided by the Mg₁₂Ce particles and the beneficial texture obtained. Higher Ce contents further increase strength, but significantly reduce ductility and cause excessive surface oxidation during extrusion. The beneficial effect of 0.2 pct Ce on mechanical properties of pure Mg is not observed when it is added to Mg-3 pct Al alloy, due to the higher affinity of Ce to Al to form the Al₁₁Ce₃ phase in the Mg-Al-Ce ternary alloys. The Mg-0.2 pct Ce alloy is a promising base alloy for further development in automotive applications; however, Al should be avoided in Mg-Ce–based extrusion alloys.     

Effect of copper and magnesium on the structure and the phase composition of boron/aluminum composite ingots

The phase composition of aluminum Al–B–Cu–Mg alloys has been studied using calculations and experimental methods. Unlike copper, magnesium is shown to substitute aluminum in the AlB₂ phase substantially. The use of Al–Cu–Mg alloys (duraluminums) as the matrix of boron/aluminum composite prepared by liquid-phase technologies is substantiated.     

Damage by eutectic particle cracking in aluminum casting alloys A356/357

The strain dependence of particle cracking in aluminum alloys A356/357 in the T6 temper has been studied in a range of microstructures produced by varying solidification rate and Mg content, and by chemical (Sr) modification of the eutectic silicon. The damage accumulates linearly with the applied strain for all microstructures, but the rate depends on the secondary dendrite arm spacing and modification state. Large and elongated eutectic silicon particles in the unmodified alloys and large π-phase (Al₉FeMg₃Si₅) particles in alloy A357 show the greatest tendency to cracking. In alloy A356, cracking of eutectic silicon particles dominates the accumulation of damage while cracking of Fe-rich particles is relatively unimportant. However, in alloy A357, especially with Sr modification, cracking of the large π-phase intermetallics accounts for the majority of damage at low and intermediate strains but becomes comparable with silicon particle cracking at large strains. Fracture occurs when the volume fraction of cracked particles (eutectic silicon and Fe-rich intermetallics combined) approximates 45 pct of the total particle volume fraction or when the number fraction of cracked particles is about 20 pct. The results are discussed in terms of Weibull statistics and existing models for dispersion hardening.     

The role of solute in grain refinement of magnesium

The effect of separate solute additions of Al, Zr, Sr, Si, and Ca on grain size of Mg has been investigated. Increasing the Al content in hypoeutectic Mg-Al alloys resulted in a continuous reduction in grain size up to 5 wt pct Al, reaching a relatively constant grain size for higher Al contents (above 5 wt pct). The effect of Sr additions was investigated in both low- and high-Al content magnesium alloys, and it was found that Sr had a significant grain refining effect in low-Al containing alloys but a negligible effect on grain size in Mg-9Al. Additions of Zr, Si, and Ca to pure magnesium resulted in efficient grain refinement. The grain refinement is mainly caused by their growth restriction effects, i.e., constitutional undercooling, during solidification, but the effect of nucleant particles, either introduced with the alloying additions or as secondary phases formed as a result of these additions, may enhance the grain refinement. A brief review of grain refinement of magnesium alloys is included in this article to provide an update on research in this field.     

Fluidity and Hot Cracking Susceptibility of A356 Alloys with Sc Additions

A356 with scandium (Sc) addition provides interesting results beyond costs. For the practical use of Sc, the effects of Sc on castability must be considered. Fluidity and hot cracking are important factors defining the castability of aluminum casting alloys. In the present work, the influence of Sc addition on the castability of A356 hypoeutectic Al–Si alloy was investigated, which was evaluated through fluidity and hot cracking susceptibility. The fluidity of the alloys was studied by measuring the total volume of solidified aluminum in a multi-channel mold. The hot cracking susceptibility of the alloys was evaluated by using a constrained-rod casting mold test. The results of the fluidity and hot cracking susceptibility test were supported by microstructural analysis. The results indicate that 0.2 wt% Sc addition significantly increases the fluidity of A356 alloy, due to the grain refinement and eutectic Si modification by changing the solidification mode. However, the fluidity slightly decreases when the Sc content increases to 0.4 wt% due to the formation of primary Al₂Si₂Sc intermetallic phase. The hot cracking of A356 alloy was completely diminished when Sc was added to the alloy.     

Combined Effect of Calcium and Silicon on the Phase Composition and Structure of Al–10%Mg Alloy

Phase transformations in the Al–Ca–Mg–Si system in the region of aluminum–magnesium alloys are investigated using the Thermo-Calc program. The liquidus projection of the quaternary system is constructed with a Mg content of 10% and it is shown that phases Al4Ca, Mg₂Si, and Al₂CaSi₂ can crystallize (in addition to the aluminum solid solution (Al)) depending on the calcium and silicon concentrations. The crystallization character of quaternary alloys is investigated with the help of a polythermal cross section calculated at concentrations of 10% Mg and 84% Al. Based on the analysis of phase transformations occurring in alloys of this section, the presence of the Al–Al₂CaSi₂–Mg₂Si quasi-ternary section in the Al–Ca–Mg–Si system was assumed. Three experimental alloys were considered from a quantitative analysis of the phase composition, notably, Al–10% Ca–10% Mg–2% Si, Al–4% Ca–10% Mg–2% Si, and Al–3% Ca–10% Mg–1% Si. Metallographic investigations and electron-probe microanalysis were performed using a TESCAN Vega 3 scanning electron microscope. Critical temperatures are determined using a DSC Setaram Setsys Evolution differential calorimeter. The experimental results agree well with the calculated data; in particular, a peak at t ~ 450°C is revealed for all alloys in curves of the nonequilibrium solidus and invariant eutectic reaction L → (Al) + Al₄Ca + Mg₂Si + Al₃Mg₂. It is established that the structure of the Al–3% Ca–10% Mg–1% Si alloy is closest to the eutectic alloy. It is no worse that the AMg10 alloy in regards to density and corrosion resistance and even surpasses it in hardness, which allows us to consider this alloy as the basis for the development of a new cast material: “natural composites.”     

Microstructural effects on the tensile and fracture behavior of aluminum casting alloys A356/357

The tensile properties and fracture behavior of cast aluminum alloys A356 and A357 strongly depend on secondary dendrite arm spacing (SDAS), Mg content, and, in particular, the size and shape of eutectic silicon particles and Fe-rich intermetallics. In the unmodified alloys, increasing the cooling rate during solidification refines both the dendrites and eutectic particles and increases ductility. Strontium modification reduces the size and aspect ratio of the eutectic silicon particles, leading to a fairly constant particle size and aspect ratio over the range of SDAS studied. In comparison with the unmodified alloys, the Sr-modified alloys show higher ductility, particularly the A356 alloy, but slightly lower yield strength. In the microstructures with large SDAS (>50 μm), the ductility of the Sr-modified alloys does not continuously decrease with SDAS as it does in the unmodified alloy. Increasing Mg content increases both the matrix strength and eutectic particle size. This decreases ductility in both the Sr-modified and unmodified alloys. The A356/357 alloys with large and elongated particles show higher strain hardening and, thus, have a higher damage accumulation rate by particle cracking. Compared to A356, the increased volume fraction and size of the Fe-rich intermetallics (π phase) in the A357 alloy are responsible for the lower ductility, especially in the Sr-modified alloy. In alloys with large SDAS (>50 μm), final fracture occurs along the cell boundaries, and the fracture mode is transgranular. In the small SDAS (<30 μm) alloys, final fracture tends to concentrate along grain boundaries. The transition from transgranular to intergranular fracture mode is accompanied by an increase in the ductility of the alloys.     

Grain boundary segregation of an Al-Zn-Mg ternary alloy

Auger electron spectroscopy (AES) has been used to measure the grain boundary concentration profiles of alloy additions in an A1-5.5 pct Zn-2.5 pct Mg ternary in as-quenched, under-, peak-, and over-aged conditions. The AES depth profiles show marked segregation of Mg and Zn to the grain boundary, in contrast to that reported previously on similar A1 alloys. It is found that this apparent contradiction can be resolved by exploiting the plasmonloss features of the AES spectra to help elucidate the grain boundary segregation. With the AES/plasmon-loss measurements, one can determine not only the concentration of Mg and Zn at the grain boundary, but also the metallurgical environments surrounding the alloy additions. It is shown that, for over-aged specimens of the Al alloy, only a fraction of the total Mg at the grain boundary is incorporated in MgZn₂ precipitates, the remainder being segregated to within a few atomic layers of the boundary.     

A356合金力学性能的工艺研究

叙述了金属锶对A356合金的变质处理，采用复合净化工艺，型腔多点冷却等技术措施，明显提高A356铝合金的力学性能。研究得出一个比较成熟的A356铝合金复杂零件的生产工艺，可供广大材料工作者借鉴。     

Sintering and aging behaviours of Al4CuXMg PM alloy

Sintering and aging behaviours of Al–Cu–Mg powder metallurgy (PM) alloy produced from elemental powders were examined. After evaluating results from thermal analysis, tests were carried out on Al–4Cu alloys with magnesium contents of 0.5, 1 and 2?wt-% and it was found that additions of 1?wt-% Mg was most effective for enhancing the transverse rupture strength (TRS) of the Al–Cu PM alloys for both as sintered and after a heat-treatment conditions. Grain size reduction in the range of 14–45% was achieved by adding magnesium into Al–Cu system. Analyses showed that produced alloys were composed of Al, Al₂Cu, Al₂CuMg and Al₇Cu₂Fe phases. Differential scanning calorimeter and dilatometer analyses revealed that alloys show swelling behaviour after the eutectic melting reaction at 548°C and swelling rates increasing as a function of magnesium content. Both high hardness value (120 HB) and TRS (650?MPa) were achieved via aging of Al4Cu1Mg alloy for 24 hours.     

The surface tension of molten aluminum and Al-Si-Mg alloy under vacuum and hydrogen atmospheres

The surface tensions of pure molten aluminum, A356 alloy (Al-7 pct Si-0.3 pct Mg), and strontium-modified A356 alloy have been measured under vacuum and hydrogen atmospheres using the sessile drop technique. The values obtained for pure aluminum at 680 °C and for A356 alloy and modified A356 alloy at 630 °C are 1.007, 0.889, and 0.844 N/m, respectively, when measured under vacuum. The addition of hydrogen gas to the atmosphere of the liquid droplet has no significant effect on the surface tension of the unmodified A356 alloy, while it lowers the surface tension of the modified alloy to 0.801 N/m. This effect is possibly due to the formation of SrH₂.     

Effect of Mg and Sr additions on the formation of intermetallics in Al-6 Wt pct Si-3.5 Wt pct Cu-(0.45) to (0.8) Wt pct Fe 319-type alloys

Al-Si alloys are materials that have been developed over the years to meet the increasing demands of the automotive industry for smaller, lighter-weight, high-performance components. An important alloy in this respect is the 319 alloy, wherein silicon and copper are the main alloying elements, and magnesium is often added in automotive versions of the alloy for strengthening purposes. The mechanical properties are also ameliorated by modifying the eutectic silicon structure (strontium being commonly employed) and by reducing the harmful effect of the β-Al₅FeSi iron intermetallic present in the cast structure. Magnesium is also found to refine the silicon structure. The present study was undertaken to investigate the individual and combined roles of Mg and Sr on the morphologies of Si, Mg₂Si, and the iron and copper intermetallics likely to form during the solidification of 319-type alloys at very slow (close to equilibrium) cooling rates. The results show that magnesium leads to the precipitation of Al₈Mg₃FeSi₆, Mg₂Si, and Al₅Mg₈Cu₂Si₆ intermetallics. With a strontium addition, dissolution of a large proportion of the needle-like β-Al₅FeSi intermetallic in the aluminum matrix takes place; no transformation of this phase into any other intermetallics (including the Al₁₅(Fe,Mn)₃Si₂ phase) is observed. When both Mg and Sr are added, the diminution of the β-Al₅FeSi phase is enhanced, through both its dissolution in the aluminum matrix as well as its transformation into Al₈Mg₃FeSi₆. The reactions and phases obtained have been analyzed using thermal analysis, optical microscopy, image analysis, and electron microprobe analysis (EMPA) coupled with energydispersive X-ray (EDX) analysis.