共查询到19条相似文献,搜索用时 78 毫秒
1.
论述了对组合把持器矿热炉电极壳参数进行合理选择的重要性,详细说明了组合把持器矿热炉电极壳参数选择的方法,并针对组合把持器矿热炉电极壳参数改进前后的变化,推导出了组合把持器矿热炉电极壳最佳的参数计算,对新建或改造电炉具有参考意义。 相似文献
2.
为改进矿热炉开炉工艺,介绍了25.5 MVA锰硅合金电炉110 kV供电直接电烘新开炉工艺。通过解析矿热炉供电原理以及对矿热炉设备特点比较,提出了大型锰硅合金矿热炉在110 kV直供电和使用组合把持器与铜瓦把持器时最适宜的电烘工艺。经实践,直接电烘开炉,不仅可以节省时间,降低成本,而且也改善了生产环境,减轻了劳动强度。 相似文献
3.
4.
介绍了铁合金矿热炉几种电极把持器在使用过程中的优缺点,指出了封闭式一一对应把持器结构是新一代埋弧电炉电极把持器结构的发展方向,而引进大电炉部分先进技术,是保证压力环把持系统正常运行的必要条件。 相似文献
5.
6.
7.
8.
10.
11.
12.
13.
为有效利用矿热炉烟气余热,提出采用烟气余热发电的可行性技术方案,该系统利用余热锅炉吸收矿热电炉烟气中的热量,产生的饱和蒸汽作为热源使用该系统投入运行后,将为有效回收矿热炉烟气余热、实现清洁生产提供积极的示范效应。 相似文献
14.
15.
介绍了矿热炉开炉的一般方法和两种开炉新工艺。通过对电极内部热应力产生和分布规律的分析,提出了直接电烘炉法在开炉中防止电极硬断的措施;对直接电焙电极的可行性进行分析后认为,电极壳的实际电流密度小于6.1A/mm^2的情况下送电焙烧电极不会击穿电极壳。将两种新开炉方法分别应用在电炉上实践,取得了较好效果。 相似文献
16.
矿热熔炼电炉铜瓦发展趋势的探讨 总被引:1,自引:1,他引:0
从矿热炉对铜瓦的性能要求方面分析了铸造铜瓦的缺陷。生产实际使用比较而言,锻造铜瓦不仅具有致密度高,冷却效果好,寿命长等优点,而且可使电耗、电炉作业率、电极寿命、炉况等均有较大改善。 相似文献
17.
介绍了气、液压弹簧保压带负荷压放电极把持器在16.5MVA电炉上应用的成功经验。提出要实现真正意义上的带负荷压放电极,应从整个电极的电极把持系统的气、液压管路绝缘、电极壳、把持筒、电极压放装置、电极抱紧装置等几个方面统筹考虑和完善性改进设计的建议。 相似文献
18.
Theofani V. Tzevelekou Hans Günter Geck Peter van Hüllen Friedrich Hfer Demetrios C. Papamantellos 《国际钢铁研究》2004,75(6):382-392
In the metallurgical plant of LARCO at Larymna, approximately 200000t/y of nickelferrous dust are collected in the gas cleaning systems of the Rotary Kilns (R/Ks) corresponding to an annual production of 100000t FeNi20%. In addition, a stockpile of one million tons of old R/K dust lies close to the plant and the community of Larymna. A “one‐stage” environmentally friendly process has been developed for the recycling of this dust by direct reduction smelting in a DC arc furnace. The industrial adaptation of this process was tested in the 125t DC‐HEP (Direct Current — Hollow Electrode Powder) furnace at Georgsmarienhütte steelwork (GMH) in Germany. About 70t of dust were directly smelted by injection through the hollow electrode of the furnace. The nickel recovery in the metal bath was 93‐99.9%. Final products were low nickel alloyed steel grades and slag suitable for special cement types production. Main cause of the dust generation in the R/Ks is the disintegration of laterite and the ore fines fraction after the ore crushing. Their separation, collection and metallurgical exploitation prior to their feeding in the R/Ks would significantly reduce the amount of the generated dust. Therefore, the smelting of untreated laterite ore fines in the DC‐HEP furnace was also indicatively tested. Thus, a zero residues industrial production process was developed for the recycling of nickel bearing dust and ore fines by smelting in a DC‐arc furnace, since the finally produced FeNi‐alloy and slag are 100% utilized in the steel and cement industry respectively. 相似文献
19.
矿热炉(铁合金炉、工业硅炉、电石炉等)中,电极把持器是设备的重要组成部分,对调整电炉功率均衡起着非常重要的作用.把持器质量的优劣直接影响着每台电炉的电能耗损及安全运行.应根据电炉容量大小、技术装备差异,操作水平等条件,以设计合理、安全可靠、经济实用的原则设计把持器,保证电炉正常运行,实现节能增产,提高企业经济效益的目的... 相似文献