Influence of Skew Angle on Reinforced Concrete Slab Bridges

The effect of a skew angle on simple-span reinforced concrete bridges is presented in this paper using the finite-element method. The parameters investigated in this analytical study were the span length, slab width, and skew angle. The finite-element analysis (FEA) results for skewed bridges were compared to the reference straight bridges as well as the American Association for State Highway and Transportation Officials (AASHTO) Standard Specifications and LRFD procedures. A total of 96 case study bridges were analyzed and subjected to AASHTO HS-20 design trucks positioned close to one edge on each bridge to produce maximum bending in the slab. The AASHTO Standard Specifications procedure gave similar results to the FEA maximum longitudinal bending moment for a skew angle less than or equal to 20°. As the skew angle increased, AASHTO Standard Specifications overestimated the maximum moment by 20% for 30°, 50% for 40°, and 100% for 50°. The AASHTO LRFD Design Specifications procedure overestimated the FEA maximum longitudinal bending moment. This overestimate increased with the increase in the skew angle, and decreased when the number of lanes increased; AASHTO LRFD overestimated the longitudinal bending moment by up to 40% for skew angles less than 30° and reaching 50% for 50°. The ratio between the three-dimensional FEA longitudinal moments for skewed and straight bridges was almost one for bridges with skew angle less than 20°. This ratio decreased to 0.75 for bridges with skew angles between 30 and 40°, and further decreased to 0.5 as the skew angle of the bridge increased to 50°. This decrease in the longitudinal moment ratio is offset by an increase of up to 75% in the maximum transverse moment ratio as the skew angle increases from 0 to 50°. The ratio between the FEA maximum live-load deflection for skewed bridges and straight bridges decreases in a pattern consistent with that of the longitudinal moment. This ratio decreased from one for skew angles less than 10° to 0.6 for skew angles between 40 and 50°.     

Effect of Multilanes on Wheel Load Distribution in Steel Girder Bridges

This paper presents the results of a parametric study that investigated the effect of multilanes and continuity on wheel load distribution in steel girder bridges. Typical one- and two-span, two-, three-, and four-lane, straight, composite steel girder bridges were selected for this study. The major bridge parameters chosen for this study were the span length, girder spacing, one- versus two-spans, and the number of lanes. These parameters were varied within practical ranges to study their influence on the wheel load distribution factors. A total of 144 bridges were analyzed using the finite-element method. The computer program, SAP90, was used to model the concrete slab as quadrilateral shell elements and the steel girders as space frame members. Simple supports were used to model the boundary conditions. AASHTO HS20 design trucks were positioned in all lanes of the one- and two-span bridges to produce the maximum bending moments. The calculated finite-element wheel load distribution factors were compared with the AASHTO and the National Cooperative Highway Research Program (NCHRP) 12-26 formulas. The results of this parametric study agree with the newly developed NCHRP 12-26 formula and both were, in general, less than the empirical AASHTO formula (S∕5.5) for longer span lengths [>15.25 m (50 ft)] and girder spacing >1.8 m (6 ft). This paper demonstrates that the multiple lane reduction factors are built into the newly developed distribution factors for steel girder bridges that were presented in the NCHRP 12-26 final report. It should be noted that AASHTO LRFD contains a similar expression that results in a value that is 50% of the value in the equations developed as a part of NCHRP 12-26. This is due to the fact that AASHTO LRFD consider the entire design truck instead of half-truck (wheel loads) as the case in the NCHRP 12-26 report and the AASHTO Standard Specifications for Highway Bridges. Therefore, this paper supports the use of the new distribution factors for steel girder bridges developed as a part of NCHRP 12-26 and consequently the distribution factors presented in the AASHTO LRFD Bridge Design Specifications.     

Shear Live-Load Distribution Factors for I-Girder Bridges

A full scale, single lane test bridge was used to evaluate a typical slab-on-girder bridge’s response to shear. The results of the shear load test provided the means to evaluate the level of detail for a finite element model that is required to accurately replicate the behavior of bridges subject to shear loads. This finite element modeling scheme was then used to evaluate more than 200 finite element bridge models. The bridge models investigated the effects of girder spacing, span length, overhang distance and skew angle on the shear live-load distribution factor. The finite element shear distribution factors were compared with those calculated according to the American Association of State Highway and Transportation Officials load and resistance factor design (AASHTO LRFD) specifications. It was found that the AASHTO LRFD procedure accurately predicted the shear distribution factor for changes in girder spacing and span length. However, the LRFD shear distribution factor for the exterior girder was found to be unconservative for certain overhang distances and overly conservative for the interior girder for higher skew angles. Alternative equations are provided for the single and multilane exterior girder correction factor.     

Probabilistic Characterization of Live Load Using Visual Counts and In-Service Strain Monitoring

It has been argued that the AASHTO LRFD design code for maximum live loads on highway bridges is overly conservative. In an attempt to determine the level of conservativeness, if any, the writers developed a methodology incorporating real-time visual data collection from traffic cameras coupled with structural strain response of girder bridges. Average daily truck traffic along with frequency of multiple presences (same lane as well as adjacent lanes) and lane-wise truck traffic distribution were estimated for a steel-girder highway bridge on I-95 in Delaware. These data compared well with predictions from a Poisson process based model developed for this study. Statistical properties of girder moments in single and multiple presence conditions were determined as well. In this particular example, the girder design moment on the 24.6?foot approach span according to AASHTO specifications was found to be about 3.5 times higher than that estimated from the in-service data.     

Equivalent Wheel Load Approach for Slender Cable-Stayed Bridge Fatigue Assessment under Traffic and Wind: Feasibility Study

In the current AASHTO LRFD specifications, the fatigue design considers only one design truck per bridge with 15% dynamic allowance. While this empirical approach may be practical for regular short and medium span bridges, it may not be rational for long-span bridges (e.g., span length >152.4?m or 500?ft) that may carry many heavy trucks simultaneously. Some existent studies suggested that fatigue may not control the design for many small and medium bridges. However, little research on the fatigue performance of long-span bridges subjected to both wind and traffic has been reported and if fatigue could become a dominant issue for such a long-span bridge design is still not clear. Regardless if the current fatigue design specifications are sufficient or not, a real understanding of the traffic effects on bridge performance including fatigue is desirable since the one truck per bridge for fatigue design does not represent the actual traffic condition. As the first step toward the study of fatigue performance of long-span cable-stayed bridges under both busy traffic and wind, the equivalent dynamic wheel load approach is proposed in the current study to simplify the analysis procedure. Based on full interaction analyses of a single-vehicle–bridge–wind system, the dynamic wheel load of the vehicle acting on the bridge can be obtained for a given vehicle type, wind, and driving condition. As a result, the dimension of the coupled equations is independent of the number of vehicles, through which the analyses can be significantly simplified. Such simplification is the key step toward the future fatigue analysis of long-span bridges under a combined action of wind and actual traffic conditions.     

Effects of State Legal Loads on Bridge Rating Results Using the LRFR Procedure

The main objective of this research was to study the effects of different specified trucks on bridge rating with the load and resistance and factor rating (LRFR) procedure. Twelve specified trucks were selected for this study, which include one AASHTO design truck, three AASHTO legal trucks, and eight state legal trucks. These rating trucks were applied on 16 selected Tennessee Dept. of Transportation bridges to obtain the LRFR ratings. The selected bridges covered four commonly used bridge types, including prestressed I-beam bridges; prestressed box beam bridges; cast-in-place T-beam bridges; and steel I-beam bridges. The research results revealed that (1) LRFR AASHTO legal load ratings factors were enveloped by the LRFR HL-93 truck ratings factors, thereby confirming the validity of the LRFR tiered approach with regard to AASHTO legal loads; (2) the lighter state legal trucks were enveloped by the HL-93 loads, whereas the heavier state trucks with closer axle spacing typically resulted in load ratings that governed over the HL-93 loads; and (3) the bridges with both high average daily truck traffic and short spans were more likely to be governed by state legal load ratings instead of HL-93 load ratings.     

The beta-adrenomimetic effect of human and animal blood serum

The conventional analysis and design of highway bridges ignore the contribution of sidewalks and∕or railings in a bridge deck when calculating the flexural strength of superstructures. The presence of sidewalks and railings or parapets acting integrally with the bridge deck have the effect of stiffening the outside girders and attracting more load while reducing the load effects in the interior girders. This paper presents the results of a parametric study showing the influence of typical sidewalks and railings on wheel load distribution as well as on the load-carrying capacity of highway bridges. A typical one-span, two-lane, simply supported, composite steel girder bridge was selected in order to investigate the influence of various parameters such as: span length, girder spacing, sidewalks, and railings. A total of 120 bridges were analyzed using three-dimensional finite-element analysis. American Association of State Highway and Transportation Officials (AASHTO) HS20 design trucks were positioned in both lanes to produce the maximum moments. The finite-element analysis results were also compared with AASHTO wheel load distribution factors. The AASHTO load and resistance factor design (LRFD) wheel load distribution formula correlated conservatively with the finite-element results and all were less than the typical empirical formula (S∕5.5). The presence of sidewalks and railings were shown to increase the load-carrying capacity by as much as 30% if they were included in the strength evaluation of highway bridges.     

Load Distribution of Existing Solid Slab Bridges Based on Field Tests

The load-carrying capacity of existing slab bridges is commonly calculated based on the equivalent width recommended by the American Association of State Highway and Transportation Officials (AASHTO). Interest in the field load testing of highway bridges has increased significantly in recent years. Load capacity of a bridge based on field testing is generally greater than that determined from standard rating calculations. The main parameters affecting the equivalent width were identified using the grillage analogy method. The results suggest that edge beam size should be considered in the equivalent width calculation. A simplified equation for the equivalent width is proposed for solid slab bridges with or without edge beams. The equivalent widths based on the AASHTO and LRFD cores was compared with those based on the field tests and analyses. The equivalent widths based on the grillage analogy and field tests are higher than those based on the AASHTO and LRFD codes, which indicates that the codes give a conservative estimate of the equivalent width. In the absence of field tests, the grillage analogy provides an accurate estimate for the equivalent width and bridge rating.     

Truck Loading and Fatigue Damage Analysis for Girder Bridges Based on Weigh-in-Motion Data

Based on data collected by weigh-in-motion (WIM) measurements, truck traffic is synthesized by type and loading condition. Three-dimensional nonlinear models for the trucks with significant counts are developed from the measured data. Six simply supported multigirder steel bridges with spans ranging from 10.67 m (35 ft) to 42.67 m (140 ft) are analyzed using the proposed method. Road surface roughness is generated as transversely correlated random processes using the autoregressive and moving average model. The dynamic impact factor is taken as the average of 20 simulations of good road roughness. Live-load spectra are obtained by combining static responses with the calculated impact factors. A case study of the normal traffic from a specific site on the interstate highway I-75 is illustrated. Static loading of the heaviest in each truck type is compared with that of the American Association of State Highway and Transportation Officials standard design truck HS20-44. Several important trucks causing fatigue damage are found.     

Vehicle Induced Dynamic Behavior of Short-Span Slab Bridges Considering Effect of Approach Slab Condition

In this paper the vehicle induced dynamic bridge responses are calculated by modeling the bridge and vehicle as one coupled system. The dynamic behavior of short slab bridges with different span lengths induced by the AASHTO HS20 truck is investigated. A parametric study is conducted to analyze the effects of different truck speeds and different road surface conditions. Critical truck speeds that result in peaks of dynamic response are found to follow the rule that describes the resonant vibration of bridges due to train loading. The approach slab condition that consists of faulting at the ends and deformation along the span is considered in the analysis. Although the effect of the along-span deformation on the dynamic response of bridges is trivial, the faulting condition of the approach slab is found to cause significantly large dynamic responses in short-span slab bridges. Impact factors obtained from numerical analyses are compared with those values specified in the AASHTO codes.     

Load Configuration and Lateral Distribution of NATO Wheeled Military Trucks for Steel I-Girder Bridges

This paper presents the lateral load distribution of various North Atlantic Treaty Organization (NATO) wheeled military trucks on a simple-span steel I-girder bridge (L = 36?m). The military trucks are classified into the military load classification (MLC) system. The MLC trucks demonstrate different load configurations when compared to the standard HS20 truck in terms of wheel-line spacing, number of axles, and weight. A calibrated three-dimensional finite-element analysis is conducted to examine the MLC load effects. The applicability of the AASHTO LRFD provisions is evaluated using 72 different load models. The wheel-line spacing and weight of the MLC trucks cause different flexural behavior and load distributions of the bridge when compared to those of HS20. The current AASHTO LRFD approach to determine live load distribution factors may be reasonably applicable to the MLC trucks, including approximately 20% of conservative predictions.     

Strength and Ductility of HPS-100W I-Girders in Negative Flexure

In current AASHTO LRFD bridge design specifications, the nominal flexural strength of I-girders made from steel with a yield stress >345 MPa (>50 ksi) is limited to the yield moment rather than the plastic moment and inelastic design procedures are not permitted. With the recent development of high performance steel (HPS) for highway bridges, the need for these restrictions should be revisited. This paper focuses on I-girders made from HPS-100W steel. Two I-girders were designed with HPS-100W steel according to the AASHTO LRFD specifications, neglecting current restrictions related to the use of high strength steels. The I-girders were tested to failure under three-point loading, which simulated the condition of negative flexure at the pier of a continuous-span bridge. The flexural strength and ductility of the HPS-100W I-girders are compared with the strength and ductility anticipated by the AASHTO LRFD specifications for conventional steel I-girders. In addition, the results of relevant previous tests of conventional steel I-girders are summarized and compared with the HPS-100W I-girder test results.     

Thermal Effects on Skewed Steel Highway Bridges and Bearing Orientation

An investigation is conducted to characterize and quantify external effects in composite steel highway bridges under thermal loading. Based on the results of a literature review, including thermal and thermoelastic analyses as well as current design code provisions, a simple but realistic thermal loading is developed for winter and summer conditions for AASHTO load and resistance factor design (LRFD) Zone 3. Three cases of bearing orientation, representative of current design practice, are examined. Parametric studies are then conducted. Hypothetical bridges are designed for a range of different span lengths, section depths, widths, and skews. Each bridge model is tested under all three constraint cases and both winter and summer thermal loading. Variations in structural response with each parameter are plotted, and the relative influence of each parameter is discussed. Design equations to predict the observed displacements and restraint forces at the bearings are then developed by a systematic regression procedure. The applicability of these proposed design equations is demonstrated by examples.     

Impact Factors for Horizontally Curved Composite Box Girder Bridges

This paper presents a method for determining the dynamic impact factors for horizontally curved composite single- or multicell box girder bridges under AASHTO truck loading. The bridges are modeled as three-dimensional structures using commercially available software. The vehicle is idealized as a pair of concentrated forces, with no mass, traveling in two circumferential paths parallel to the curved centerline of bridges. An extensive parametric study is conducted, in which over 215 curved composite box girder bridge prototypes are analyzed. The key parameters considered in this study are: Number of cells, number of lanes, degree of curvature, arc span length, slope of the outer steel webs, number and area of bracing and top chord systems, and truck(s) speed and truck(s) positioning. Based on the data generated from the parametric study, expressions for dynamic impact factors for longitudinal moment, reaction, and deflection are proposed as function of the ratio of the arc span length to the radius of curvature. The results from this study would enable bridge engineers to design horizontally curved composite box girder bridges more reliably and economically. Furthermore, the results can be used to potentially increase the live-load capacity of existing bridges to prevent posting or closing of the bridge.     

Live Load Distribution in Girder Bridges Subject to Oversized Trucks

A significant challenge facing motor carriers and engineers in this nation is the limitation of vehicle size and weight based on pavement and bridge capacity. However, the current demands of society and industry occasionally require a truck to carry a load that exceeds the size and weight of the legal limit. In these cases, engineering analysis is required before a permit is issued to ensure the safety of the structures and roadways on the vehicle's route. A truck with a wheel gauge larger than the standard 1.83 m (6 ft) gauge requires additional engineering effort because the wheel load girder distribution factors (GDFs) established by AASHTO cannot be used to accurately estimate the live load in the girders. In this study, the finite-element method is used to develop modification factors for the AASHTO flexure and shear GDFs to account for oversized trucks. The results of the analysis showed that the use of the proposed modification factors with the specification-based GDFs can help increase the allowable loads on slab-on-girder bridges.     

Development of Live-Load Distribution Factors for Glued-Laminated Timber Girder Bridges

This paper presents simple relationships for calculating live-load distribution factors for glued-laminated timber girder bridges with glued-laminated timber deck panels. Analytical models were developed using the Ansys 113 finite-element program, and the results were validated using recorded data from four in-service timber bridges. The effects of the bridge span length, the spacing between girders, and the bridge width on the distribution of the live load were investigated by using the validated models. The live-load distribution factors obtained from the field test and the analytical models were compared with those obtained using the AASHTO LRFD Bridge Design Specifications2 live-load distribution relations. The comparison showed that the live-load distribution factors obtained by using the AASHTO LRFD Bridge Design Specifications2 were conservative. For this reason, statistical methods were used to develop accurate relationships that can be used to calculate the live-load distribution factors in the design of glued-laminated girder bridges.     

Live-Load Distribution Factors for Concrete Box-Girder Bridges

The current American Association of State Highway and Transportation Officials (AASHTO) Load and Resistance Factor Design (LRFD) Specifications impose fairly strict limits on the use of its live-load distribution factor for design of highway bridges. These limits include requirements for a prismatic cross section, a large span-length-to-width ratio, and a small plan curvature. Refined analyses using 3D models are required for bridges outside of these limits. These limits place severe restrictions on the routine design of bridges in California, as box-girder bridges outside of these limits are frequently constructed. This paper presents the results of a study investigating the live-load distribution characteristics of box-girder bridges and the limits imposed by the LRFD specifications. Distribution factors determined from a set of bridges with parameters outside of the LRFD limits are compared with the distribution factors suggested by the LRFD specifications. For the range of parameters investigated, results indicated that the current LRFD distribution factor formulas generally provide a conservative estimate of the design bending moment and shear force.     

Truck Models for Improved Fatigue Life Predictions of Steel Bridges

A new fatigue load model has been developed based on weigh-in-motion (WIM) data collected from three different sites in Indiana. The recorded truck traffic was simulated over analytical bridge models to investigate moment range responses of bridge structures under truck traffic loadings. The bridge models included simple and two?equally continuous spans. Based on Miner’s hypothesis, fatigue damage accumulations were computed for details at various locations on the bridge models and compared with the damage predicted for the 240-kN (54-kip) American Association of State Highway and Transportation Officials (AASHTO) fatigue truck, a modified AASHTO fatigue truck with an equivalent effective gross weight, and other fatigue truck models. The results indicate that fatigue damage can be notably overestimated in short-span girders. Accordingly, two new fatigue trucks are developed in the present study. A new three-axle fatigue truck can be used to represent truck traffic on typical highways, while a four-axle fatigue truck can better represent truck traffic on heavy duty highways with a significant percentage of the fatigue damage dominated by eight- to 11-axle trucks.     

LRFD Orthotropic Plate Model for Live Load Moment in Filled Grid Decks

Due to the orthogonal elastic properties and significant two-way bending action, orthotropic plate theory may best be used to describe the behavior of concrete filled grid bridge decks. The current AASHTO LRFD specification employs an orthotropic plate model with a single patch load to predict live load moment in concrete filled grid bridge decks, which may not be conservative. This paper presents alternative equations to predict maximum moments, based on classical orthotropic plate theory, which include multiple patch loads, both the LRFD design truck and tandem load cases, and the two most common deck orientations. The predicted moments are verified through finite-element analyses.     

Live Load Distribution for Steel Girder Bridges

This paper deals with distribution of truck load on girder bridges. Previous analytical studies based on finite-element method indicated that AASHTO code-specified girder distribution factors (GDFs) are inaccurate. In particular, GDFs appear to be conservative for longer spans and larger girder spacing, but too permissive for short spans and girder spacings. Therefore, a field testing program was carried out including about 20 steel girder bridges with spans up to 45 m. For each tested structure, GDFs were determined by measuring strains in the girders under heavy trucks. Test trucks were 11-axle vehicles, loaded to the legal limit in Michigan (over 650 kN). The strains were recorded for a single truck and for two trucks side-by-side. The tests were repeated for crawling speed and normal traffic speed for the location. In all tested bridges, the GDFs determined from the field measurements are lower than code-specified values. In addition, the considered bridges were analyzed using a commercial finite-element software package, ABAQUS. The analytical results were compared with those from field tests. It was observed that the maximum values of the strain and corresponding stress are lower than analytical values obtained using ABAQUS. The reason for this discrepancy is unintended composite action and partial fixity of supports (rather than simple supports).