共查询到20条相似文献,搜索用时 125 毫秒
1.
汤志宏 《金属材料与冶金工程》2000,(6):21-24
在高速线轧机上,轧制不同规格的产品时,通过适当选择夹送辊的槽形及辊径、夹送方式、并对夹送辊辊缝、夹送辊速度等进行联合调整,可以保证精轧-夹送辊之间处于合适的张力控制状态,实现稳定轧制。 相似文献
2.
3.
4.
5.
连轧过程张力控制系统的进化与分析 总被引:1,自引:0,他引:1
冷、热连轧的发展首先在冷连轧机上实施了张力信号与辊缝闭环的恒张力和恒厚度控制方法。分析出张力与辊缝闭环的厚控系统存在极限精度,所以要求提高坯料厚度精度、第一机架用偏心最小的轧辊和DAGC。将张力(或活套电流)与辊缝闭环的流量AGC应用到热连轧机上可以大大提高热连轧板带厚度精度,估计可达到±15μ。 相似文献
6.
7.
通过对生产过程的分析,卷取塔形主要由带钢头部不均匀受力产生的内塔形及尾部张力减少产生的外塔形导致。改造卷取机侧导尺平行度及短行程控制时序,解决了内塔形的问题;上夹送辊凸度为0.75mm,下夹送辊凸度为1.5mm,合理配置辊型;同时开发了夹送辊压力修正功能并优化卷取机张力设定。优化改进后,由于塔形问题产生的次品量减少60%,提高了热轧带钢综合合格率。 相似文献
8.
9.
10.
实现厚规格精冲带钢的顺利卷取是精冲钢冷连轧生产工艺成功应用的关键。利用4辊可逆冷轧机进行轧制试验,在MMS-200热模拟试验机上测定精冲钢的应力-应变曲线,建立精冲钢冷轧终态变形抗力模型。针对1750mm冷连轧机组配置的卡罗塞尔卷取机,进行精冲带钢卷取过程的机理分析和卷取状态的受力分析,为精冲钢冷连轧极限厚度卷取能力的分析和计算提供理论支撑。在此基础上,完成了不同摩擦条件下多规格精冲钢冷连轧生产卷取机的极限厚度计算,并给出相应的安全卷取厚度窗口。该研究适合于工业生产实践,对精冲钢冷连轧生产工艺研究具有重要意义。 相似文献
11.
12.
13.
14.
《钢铁冶炼》2013,40(3):163-170
AbstractIn order to improve the flatness of hot rolled thin gauge steel strip, a new type of roll contour configuration was developed for a four-high temper rolling mill based on the finite element method analysis. The roll contour configuration consists of a variable contact back-up roll contour and a positive crown work roll contour. Both can be described as sixth order polynomial functions. The variable contact back-up roll not only reduces the roll stack deflection and contact stress concentration between work and back-up rolls, but also increases the control capability of the bending force of the work roll. Positive crown work roll contour is utilised to compensate roll wear and in turn the length of temper rolling schedule can be prolonged. After this roll contour configuration was applied on the temper rolling mill of Qiangang Company of Shougang Group, the flatness of hot rolled thin gauge strip was improved by 10% and the working efficiency was also increased as the length of temper rolling schedule was increased. 相似文献
15.
这种12辊轧机采用了不同于Sendzim ir轧机的整体机架和Sundw ig的四立柱机架,而类似于传统4、6辊轧机的整体机架。机架内装有可上下移动的上下辊箱,每个辊箱内用芯轴固定安装了两大一小三组背衬轴承。轧机在下辊箱内设有直接作用式板形调节装置。轧机采用小抛线型直接作用式液压压下装置。这两台轧机均可将厚3~2.75mm的热轧带钢不经中间退火轧制成0.3~0.2mm成品厚度的冷硬带钢。 相似文献
16.
17.
18.
为了拓展宽幅硅钢等对边降有特殊要求的高端产品的规格,提升某1700mm冷连轧机组的带钢边降控制功能,克服生产中存在的单锥度辊窜辊行程小、窜辊功能使用不充分、边降波动明显等问题,对单锥度工作辊辊形及边降控制窜辊策略进行了研究,提出了单锥度辊边降控制段的设计方法。运用ANASYS 9.0建立了单锥度辊轧机三维有限元仿真模型,分析了轧机的板形控制特性。采用影响系数法,建立了冷连轧静态综合分析数学模型,研究了来料厚度波动和来料硬度波动对冷连轧机生产产生的影响。通过分析可以看出:单锥度辊轧机通过工作辊窜辊可增强其辊缝横向刚度,提高了轧机克服来料波动能力和轧制的稳定性。现场轧制试验表明:采用该单锥度辊及窜辊策略,带钢边降由14.9μm下降至7.5μm,边降波动被控制在±5μm范围内,边降波动得到了一定的抑制。 相似文献
19.
It has a strict demand for the transverse thickness difference of silicon steel. To reduce the transverse thickness difference of the cold rolled strip, it must reduce the crown and the wedge of the hot rolled strip. 7-Stands continuously variable crown (CVC) hot rolling mills are conventionally applied to roll silicon steel. However, the CVC rolling mills have many defects to roll silicon steel as a result of the strict demands for the crown and the wedge and the characteristics of the CVC rolling mill. The large concave roll (LCR) technology was puts forward to solve that problem. The LCR technology includes the design of the roll contour and the roll free shifting strategies. The results of simulations and experiments show that the LCR technology can not only ensure the crown target of silicon steel, but also enlarge the coil quantity in a rolling schedule and improve the hot rolled strip edge-drop in the late of rolling schedule. This technology provides guidance for the crown control of the hot rolled silicon steel. 相似文献
20.
针对国内某厂厚板轧机出现轧制力偏差的实际情况,研究了轧机两侧刚度差对轧制力偏差的影响。建立了支撑辊标高调整时候阶梯垫上面残留氧化铁皮对轧机机座刚度的影响模型,基于模型替代法建立了整体轧机有限元模型,进而通过有限元模拟计算出轧机机座刚度差引起的轧辊挠度改变量、出口厚度变化量、辊间压力变化量以及轧机两侧轧制力的偏差。结果表明:当氧化铁皮的厚度为5mm残余面积分别为26.66%、36.79%和46.92%时,氧化铁皮的等效刚度变化范围为[605,674]kN/mm。当轧机上下无刚度差时,轧机两侧轧制力偏差最小,偏差为5t;当压入的残余氧化铁皮面积最多时,此时轧机两侧轧制力偏差最大,数值为30t。 相似文献