低温等离子体改性LaCoO_3催化剂去除炭烟颗粒的催化性能

采用低温等离子体对LaCoO_3复合氧化物进行表面改性,利用XRD、FT-IR、H2-TPR和O_2-TPD等对催化剂表面物化性能进行表征,分析等离子体对催化剂表面物化性质的影响。采用程序升温氧化反应评价催化剂对模拟柴油机炭烟催化氧化的活性。结果表明,等离子体改性促进了催化剂表面晶格氧的活化,增加了活性氧物种数目,从而增强了催化剂对炭烟催化氧化活性,炭烟催化起燃温度Ti由278℃降到274℃,峰值温度Tm由354℃降至345℃,燃尽温度Tf由425℃降至386℃。     

Supported Co-based perovskites as catalysts for total oxidation of methane

Supported LaCoO₃ perovskites with 2, 5, 10, 15, 20 and 30 wt.% loading were prepared by impregnation of a Ce_0.8Zr_0.2O₂ support (40 m² g⁻¹) with: (i) a solution of La and Co nitrates and (ii) a “citrate” solution, namely containing La and Co nitrates, and citric acid. All precursors were decomposed and calcined at 700 °C for 5 h. XRD investigations indicated the formation of a pure perovskite phase only if citrates were used. These materials were tested as catalysts for methane combustion in the temperature range 300–700 °C. All catalysts showed a lower T₅₀ (the temperature at which the conversion level of methane is 50%) than the Ce_0.8Zr_0.2O₂ support or non-supported LaCoO₃. The activity increased continuously with the perovskite loading. The samples prepared from citrates were slightly more active than from nitrates. This is due to a more homogeneous surface, as indicated by XPS measurements. The presence of a well-characterized perovskite phase (as opposed to highly dispersed elements) seems necessary for good activity. A higher reaction rate per perovskite weight is observed for low loadings when compared to bulk LaCoO₃, but the variation with perovskite loading presents a breakpoint, suggesting complex interactions in the catalysts or in the oxidation mechanism.

In spite of the experimental impossibility to evaluate the area developed by the supported perovskite, an approximative approach strongly suggests a synergy between the support and supported species.     

介孔LaCoO_3催化剂的制备及其光催化性能

以SBA-15为模板剂,采用纳米铸型法制备具有高比表面积的有序介孔钙钛矿型氧化物LaCoO_3催化剂,通过XRD、N2吸附-脱附和H2-TPR等对催化剂进行表征,并与溶胶-凝胶法制备的LaCoO_3催化剂比较,研究其光催化降解亚甲基蓝的性能。结果表明,纳米铸型法制备的立方晶系钙钛矿型LaCoO_3催化剂的比表面积为84 m2·g-1,对100 mg·L-1亚甲基蓝降解率达71.60%,远优于溶胶-凝胶法制备的LaCoO_3催化剂。     

Ceria-based oxides as supports for LaCoO3 perovskite; catalysts for total oxidation of VOC

Supported LaCoO₃ perovskites with 10 and 20 wt.% loading were obtained by wet impregnation of different Ce_1−xZr_xO₂ (x = 0–0.3) supports with a solution prepared from La and Co nitrates, and citric acid. Supports were also prepared using the “citrate method”. All materials were calcined at 700 °C for 6 h and investigated by N₂ adsorption at −196 °C, XRD and XPS. XRD patterns and XPS measurements evidenced the formation of a pure perovskite phase, preferentially accumulated at the outer surface. These materials were comparatively tested in benzene and toluene total oxidation in the temperature range 100–500 °C. All catalysts showed a lower T₅₀ than the corresponding Ce_1−xZr_xO₂ supports. Twenty weight percent LaCoO₃ catalysts presented lower T₅₀ than bulk LaCoO₃. In terms of reaction rates per mass unit of perovskite calculated at 300 °C, two facts should be noted (i) the activity order is more than 10 times higher for toluene and (ii) the reverse variation with the loading as a function of the reactant, a better activity being observed for low loadings in the case of benzene. For the same loading, the support composition influences drastically the oxidative abilities of LaCoO₃ by the surface area and the oxygen mobility.     

Effect of Ru on LaCoO3 perovskite-derived catalyst properties tested in oxidative reforming of diesel

The oxidative reforming of diesel over Co/La₂O₃ and Ru–Co/La₂O₃ catalysts derived from LaCoO₃ perovskite precursors was studied. Physicochemical characterization by XPS, TPR and XRD revealed that the incorporation of Ru to LaCoO₃ produces changes in LaCoO₃ evidenced by a smaller size of the LaCoO₃ particles and cobalt segregation on the LaCoO₃ surface. The modifications in the structure of LaCoO₃ induced by the addition of Ru directly affect the dispersion and morphology of Co particles developed under the reaction. The active phases derived from pretreatment of perovskites evolve differently with time on stream, being observed that the presence of a greater proportion of perovskite phase in the Ru/LaCoO₃ sample produces an increase in catalyst stability. TPD-MS analysis also indicates that bulk oxygen release from the Ru–Co/La₂O₃ sample could improve its catalytic behaviour. The characterization of used samples reveals that improvements in the cobalt surface concentration and Co–La₂O₃ interactions contribute to the better catalytic stability of the Ru–Co/La₂O₃-derived catalyst.     

An in situ study of the NO + H2 + O2 reaction on Pd/LaCoO3 based catalysts

In situ X-ray diffraction (XRD) and quasi in situ X-ray photoelectron spectroscopy (XPS) measurements were complementary used to investigate structural and surface modifications of a palladium-supported on LaCoO₃ perovskite catalyst under various controlled atmospheres, particularly during the reduction of NO by hydrogen under lean conditions, in the presence of a large excess of oxygen.

An extensive reduction of the perovskite was evidenced during the pre-activation thermal treatment of the palladium-supported catalyst under hydrogen at 773 K leading to the formation of Pd particles in contact with Co⁰ and La₂O₃. In the presence of an excess of oxygen, the catalyst structure changes during the reaction. The reduced solid is progressively transformed into LaCoO₃ in the range of 873–1173 K. However, such a bulk transformation probably occurs at lower temperatures at the surface of the solid according to XPS analyses. At the same time, the binding energy (BE) level of the Pd 3d_5/2 photopeak increases up to 337.5 eV which reveals the stabilisation of oxidic palladium species in a different chemical environment than that corresponding to PdO. Such changes induced different catalytic properties of the catalyst during the reduction of NO by H₂.     

NiO/ZnO-Al2O3-SiO2吸附剂反应吸附脱硫机理

对比考察了N₂和H₂载气下NiO/ZnO-Al₂O₃-SiO₂吸附剂对模拟汽油的吸附脱硫效果。与H₂气氛下的脱硫效果相比,N₂载气下吸附剂也具有明显脱硫效果,吸附剂表面积炭导致其脱硫效率降低,从而推断出NiO可以直接进行反应吸附脱硫反应。对不同载气和还原条件下反应前后吸附剂进行XRD、H₂-TPR、TOPT和XPS等表征结果表明：反应吸附条件下,吸附剂载体表面NiO难以被还原成单质Ni,说明H₂气氛下反应吸附过程中吸附剂中的NiO与单质Ni可能共同参与反应,反应后吸附剂上NiS_x存量极少。根据以上研究结果,提出了NiO为活性中心的反应吸附脱硫机理。     

ZSM-5分子筛负载金属氧化物催化剂催化燃烧含丙烯腈废气的性能

采用等体积浸渍法将过渡金属Cu负载到ZSM-5分子筛上,并与其他金属(Fe、Co、Ag、Pd、Ce)共浸渍得到负载型催化剂,将其用于全组分丙烯腈废气的催化脱除过程。催化活性评价结果表明,丙烯腈在Cu/ZSM-5催化剂上320℃可以实现完全转化;掺杂质量分数2%Ce后,丙烯腈的完全转化温度降低到300℃,高选择生成N2的温度窗口也变宽,催化剂稳定性高。通过X射线衍射、氮气吸附-脱附、氢气-程序升温还原、氨气-程序升温脱附和X射线光电子能谱等对催化剂的物化性能进行表征,结果表明,催化剂催化氧化丙烯腈尾气的性能依赖于Cu^2+的还原能力、催化剂表面弱酸与中强酸含量以及表面Cu^2+丰度。     

Catalytic oxidation over lanthanum-transition metal perovskite materials

The thrust of this work is to follow the defect chemistry of the simple LaCoO₃ system in an attempt to probe if there is a relationship between the defect chemistry and the activity of this perovskite-type material to catalytic methane combustion. A simple flow-through reactor has been used to study the combustion of methane between room temperature and 1100°C. Using a gel-type precipitation method it has been proved possible to synthesise a single phase perovskite material with a bulk La:Co metal atom ratio of 1:1.1. PXRD, Rietveld analysis and density measurements show that the perovskite phase is non-stoichiometric with a deficiency of lanthanum ions in the lattice. This material is rather ineffective as a catalytic material. A more active form can be prepared at a La:Co metal atom ratio of 1:1 when a mixed phase (perovskite/lanthana) is produced. This material exhibits both higher activity to methane combustion and the storage/evolution of oxygen (as measured using DSC and TPD techniques).

The results of activity tests have been rationalised using XPS where large amounts of O⁻ species are seen at the surface. It is proposed that these ions occupy anion vacancies created to compensate for the reduced cation charge in the lattice. This is not possible for the single phase material where vacancies are compensated for by the presence of valency changes of cobalt and/or oxygen.

Further work has been carried by doping of the perovskite with cations of valencies +2, +3 and +4 in an attempt to control the non-stoichiometry. In this way, it has been proved possible to provide simple synthetic routes to active methane combustion catalysts.     

Studies of the activation process over Pd perovskite-type oxides used for catalytic oxidation of toluene

Calcined and reduced catalysts Pd/LaBO₃ (B = Co, Fe, Mn, Ni) were used for the total oxidation of toluene. Easiness of toluene destruction was found to follow the sequence based on the T₅₀ values (temperature at which 50% of toluene is converted): Pd/LaFeO₃ > Pd/LaMnO_3+δ > Pd/LaCoO₃ > Pd/LaNiO₃. In order to investigate the activation process (calcination and reduction) in detail, the reducibility of the samples was evaluated by H₂-TPR on the calcined catalysts. Additionally, characterization of the Pd/LaBO₃ (B = Co, Fe) surface was carried out by X-ray photoelectron spectroscopy (XPS) at each stage of the global process, namely after calcination, reduction and under catalytic reaction at either 150 or 200 °C for Pd/LaFeO₃ and either 200 or 250 °C for LaCoO₃. The different results showed that palladium oxidized entities were totally reduced after pre-reduction at 200 °C for 2 h (2 L/h, 1 °C/min). As LaFeO₃ was unaffected by such a treatment, for the other perovskites, the cations B are partially reduced as B³⁺ (B = Mn) or B²⁺ even to B⁰ (B = Co, Ni). In the reactive stream (0.1% toluene in air), Pd⁰ reoxidized partially, more rapidly over Co than Fe based catalysts, to give a Pd²⁺/Pd⁴⁺ and Pd⁰/Pd²⁺/Pd⁴⁺ surface redox states, respectively. Noticeably, reduced cobalt species are progressively oxidized on stream into Co³⁺ in a distorted environment. By contrast, only the lines characteristic of the initial perovskite lattice were detected by XRD studies on the used catalysts. The higher activity performance of Pd/LaFeO₃ for the total oxidation of toluene was attributed here to a low temperature of calcination and to a remarkable high stability of the perovskite lattice whatever the nature of the stream which allowed to keep a same palladium dispersion at the different stages of the process and to resist to the oxidizing experimental conditions. On the contrary, phase transformations for the other perovskite lattices along the process were believed to increase the palladium particle size responsible of a lower activity.     

Rh–La(Mn,Co)O3 monolithic catalysts for the combustion of methane under fuel-rich conditions

Novel Rh–La(Mn,Co)O₃ structured catalysts were developed for the partial oxidation of methane to syngas intended as a preliminary conversion step in combustion systems such as power turbines and utility burners employing a fuel-rich fuel-lean approach to reduce NO_x formation. Active components were impregnated on La–γ-Al₂O₃ washcoated honeycomb monoliths and the catalysts were characterised by BET, SEM/EDS, H₂-TPR, and in situ FT-IR under reaction conditions. Catalytic partial oxidation of methane was tested under both pseudo-isothermal and pseudo-adiabatic conditions showing that the process can be conducted with high yield and selectivity: improved and stable performances were found especially in the case of Rh–LaMnO₃ catalyst, due to the synergism between active sites and to the stabilization of the noble metal.     

载体表面羟基种类对DMO加氢用Cu/SiO2催化剂性能的影响

通过程序升温焙烧改变气相纳米二氧化硅表面的羟基含量及种类,并以其为载体,采用蒸氨法制备了Cu/SiO₂催化剂,使用比表面积测试（BET）、傅里叶变换红外光谱（FTIR）、漫反射傅里叶变换红外光谱（DRIFT）、X射线衍射（XRD）、透射电子显微镜（TEM）、H₂程序升温还原（H₂-TPR）、NH₃/CO₂程序升温脱附（NH₃/CO₂-TPD）、X射线光电子能谱（XPS）、俄歇电子能谱（AES）等方法研究了Cu/SiO₂催化剂的结构和酸碱性,采用固定床反应器在低温（448K）、低压（1.5MPa）的反应条件下进行草酸二甲酯加氢制备乙二醇的反应,评价其催化活性。结果表明,高温焙烧二氧化硅载体可显著改变后续合成Cu/SiO₂催化剂的结构并降低其酸碱性,对提高乙二醇选择性和降低草酸二甲酯加氢过程中醇类或醚类副产物的选择性具有明显的促进作用。但同时该过程会导致催化剂的活性降低,载体焙烧（473K）后合成的催化剂均需要提高氢酯比方能获得最佳反应结果。其中经873K焙烧的二氧化硅制备的Cu/SiO₂-4催化剂,在最佳反应条件下乙二醇的选择性由低温焙烧后的92%左右提升到97%以上,草酸二甲酯转化率保持在100%。     

Si掺杂对Cu/ZrO2催化CO2加氢制甲醇性能的影响

为了提高Cu/ZrO₂催化剂在二氧化碳加氢制甲醇中的催化活性,制备了一系列不同Si/Zr的Si-ZrO₂载体并负载5%（质量分数）Cu得到了Cu/Si-ZrO₂催化剂。对所制备的催化剂进行了X射线衍射（XRD）、N₂物理吸脱附（BET）、X射线光电子能谱（XPS）、氢气程序升温还原（H₂-TPR）、二氧化碳程序升温脱附（CO₂-TPD）及高分辨透射电子显微镜 （HRTEM） 的表征。结果表明,Si的掺杂使得Cu/ZrO₂体系获得了稳定的晶相,大的比表面积和更多的碱性位点,尤其是中强碱性位点,同时产生了更多的氧空位,促进了CO₂的吸附和转化,因此得到了更高活性的催化剂。当Si与Zr的摩尔比为0.2时,在质量空速为6000 ml·g^-1·h^-1,温度为220℃、压力为3.0 MPa,V（H₂）∶V（CO₂）=3∶1（体积比）条件下,催化剂的CO₂转化率为4.6%,CH₃OH选择性为85%。     

Si掺杂对Cu/ZrO2催化CO2加氢制甲醇性能的影响

为了提高Cu/ZrO₂催化剂在二氧化碳加氢制甲醇中的催化活性,制备了一系列不同Si/Zr的Si-ZrO₂载体并负载5%（质量分数）Cu得到了Cu/Si-ZrO₂催化剂。对所制备的催化剂进行了X射线衍射（XRD）、N₂物理吸脱附（BET）、X射线光电子能谱（XPS）、氢气程序升温还原（H₂-TPR）、二氧化碳程序升温脱附（CO₂-TPD）及高分辨透射电子显微镜 （HRTEM） 的表征。结果表明,Si的掺杂使得Cu/ZrO₂体系获得了稳定的晶相,大的比表面积和更多的碱性位点,尤其是中强碱性位点,同时产生了更多的氧空位,促进了CO₂的吸附和转化,因此得到了更高活性的催化剂。当Si与Zr的摩尔比为0.2时,在质量空速为6000 ml·g^-1·h^-1,温度为220℃、压力为3.0 MPa,V（H₂）∶V（CO₂）=3∶1（体积比）条件下,催化剂的CO₂转化率为4.6%,CH₃OH选择性为85%。     

Silver modified Cu/SiO2 catalyst for the hydrogenation of methyl acetate to ethanol

A series of silver modified Cu/SiO_2 catalysts were synthesized with ammonia-evaporation method and applied in vapor-phase hydrogenation of methyl acetate to ethanol. The influence of additive ‘Ag' on the structural evolution of catalyst was systematically studied by several characterization techniques, such as N_2 adsorption–desorption, N_2O titration, PXRD, FTIR, in-situ FTIR, H_2-TPR, H_2-TPD, XPS and TEM. Results showed that incorporation of a small amount of Ag could enhance the structural stability, and the strong interaction between Cu and Ag species was conducive to increase the dispersion of copper species and create a suitable Cu~(+)/(Cu~0+ Cu~(+)) ratio, which was proposed to be responsible for the improved catalytic activity. The maximum conversion of MA(94.1%)and selectivity of ethanol(91.3%) over optimized Cu-0.5 Ag/SiO_2 and 120 h on stream without deactivation under optimal conditions demonstrates its excellent stability.     

四效催化剂La-K-Co-Mn同时去除CO、C_xH_y、PM和NOx的研究

四效催化剂的活性组分La0.8K0.2Co0.7Mn0.3O3的合成温度对柴油烟气的净化效果有较大影响,通过X射线衍射、电子扫描电镜、程序升温、比表面积检测和在线效率检测发现,750℃合成的四效催化剂净化柴油烟气的效果最好。通过K和Mn同时部分取代La Co O3中La和Co,探讨K和Mn对钙钛矿结构和烟气净化效果的影响。比表面积检测发现,涂覆改性γ-Al2O3后,整体式催化剂比表面积增加,催化性能得到有效改善。     

Sr改性Cu催化剂的果糖加氢制备甘露醇性能

使用共沉淀法制备负载Cu催化剂。通过添加碱土金属Sr，对Cu催化剂进行了改性，以提高Cu催化剂在果糖加氢制备甘露醇过程中的活性和选择性。采用ICP-MS、TEM、XRD、H₂-TPR、XPS和CO₂-TPD等对所制备的催化剂进行了系统表征。结果表明：Sr的添加能增大催化剂的比表面积，促进活性组分Cu的分散，从而提高了催化剂的活性，并且增加了催化剂的碱性，使果糖优先形成β-呋喃糖中间体，从而提高了甘露醇的选择性。在果糖浓度为1.1 mol·L^-1、催化剂用量为反应物质量的6%、反应温度为373 K、反应氢压为4.0 MPa、Cu/Sr原子比为7∶1的反应条件下，果糖转化率为99%，甘露醇的选择性为79%。催化剂循环使用了20次，其催化稳定性基本保持不变。     

不同Pt前体制备Pt/CeO2催化剂对其结构及性能的影响

Pt与载体间的相互作用会影响到本征Pt纳米粒子的催化活性,不同Pt前体制备Pt/CeO₂催化剂会使其表现出完全不同的催化性能。分别采用金属胶体粒子原位沉积法、浸渍法以及浸渍还原的方式制备了Pt/CeO₂催化剂,通过X 射线衍射、程序升温还原、X射线光电子能谱以及高分辨透射电镜对催化剂进行表征,在CO氧化以及甲苯燃烧反应中评价催化剂活性。结果表明,胶体粒子原位沉积法制备Pt/CeO₂催化剂,能够将优先合成好的Pt纳米粒子直接以金属态Pt⁰的形式负载到载体表面,且保证其高度均匀分散,丰富的表面Pt⁰很好地充当了CO、甲苯反应时的活化位点,催化剂表现出优异的性能;浸渍还原法中,Pt纳米粒子之间会发生团聚现象,同时部分Pt又以Pt²⁺的形式与CeO₂之间形成了Pt-O-Ce相互作用,载体表面暴露Pt⁰含量的下降是催化剂表现出较弱活性的主要原因;浸渍法中,以Pt离子对Pt进行负载,Pt完全以Pt²⁺的形式参与到Pt-O-Ce键成键中,表面Pt⁰缺失,催化剂表现出明显的失活现象。Pt/CeO₂催化剂中,起主要活性作用的是金属态Pt⁰,胶体粒子原位沉积法能够实现Pt⁰的直接负载,对于提高Pt基催化剂中Pt的利用率,降低Pt资源消耗都具有重要意义。     

Effect of LaCoO3 perovskite deposition on ceria-based supports on total oxidation of VOC

Supported LaCoO₃ perovskites with 10 wt.% loading were prepared by impregnation of different supports containing ceria with a solution of La and Co nitrates and citric acid. All precursors were calcined at 700 °C for 5 h. XRD investigations indicated the perovskite formation via “citrate” precursor only on ceria support. All catalysts were tested for toluene total oxidation in the temperature range 100–600 °C. In spite of a large surface area, alumina-supported perovskites showed a lower global activity. It appears then the necessity of the presence of a perovskite phase for good oxidative activity. In terms of reaction rates higher reaction rates per perovskite weight were observed for all supported catalysts when compared to bulk LaCoO₃.     

制备方法对Ni-Al_2O_3催化剂乙酰丙酸加氢性能的影响

分别采用浸渍法、沉积-沉淀法和共沉淀法制备了Ni-Al_2O_3催化剂,采用H2-TPR/TPD、XRD、NH3-TPD等对催化剂进行表征,并研究其催化乙酰丙酸加氢性能。结果表明,共沉淀法制备的催化剂中存在强的金属-载体相互作用、活性金属分散度高以及丰富的酸性中心。该催化剂表现出优异的催化乙酰丙酸加氢合成%-戊内酯性能以及高的使用稳定性。在160℃和4 MPa氢气压力反应条件下,乙酰丙酸转化率与%-戊内酯选择性可分别达85.0%和78.0%,催化剂循环使用3次时活性仍基本保持恒定。