Giant electromechanical strain response in lead‐free SrTiO3‐doped (Bi0.5Na0.5TiO3–BaTiO3)–LiNbO3 piezoelectric ceramics

Lead‐free 0.985[(0.94?x)Bi_0.5Na_0.5TiO₃–0.06BaTiO₃–xSrTiO₃]–0.015LiNbO₃ [(BNT–BT–xST)–LN, x=0‐0.05] piezoelectric ceramics were prepared using a conventional solid‐state reaction method. It was found that the long‐range ferroelectric order in the unmodified (BNT–BT)–LN ceramic was disrupted and transformed into the ergodic relaxor phase with the ST substitution, which was well demonstrated by the dramatic decrease in remnant polarization (P_r), coercive field (E_c), negative strain (S_neg) and piezoelectric coefficient (d₃₃). However, the degradation of the ferroelectric and piezoelectric properties was accompanied by a significant increase in the usable strain response. The critical composition (BNT–BT–0.03ST)–LN exhibited a maximum unipolar strain of ~0.44% and corresponding normalized strain, S_max/E_max of ~880 pm/V under a moderate field of 50 kV/cm at room temperature. This giant strain was associated with the coexistence of the ferroelectric and ergodic relaxor phases, which should be mainly attributed to the reversible electric‐field‐induced transition between the ergodic relaxor and ferroelectric phases. Furthermore, the large field‐induced strain showed relatively good temperature stability; the S_max/E_max was as high as ~490 pm/V even at 120°C. These findings indicated that the (BNT–BT–xST)–LN system would be a suitable environmental‐friendly candidate for actuator applications.     

Preparation and Electric Properties of Bi0.5Na0.5TiO3–Bi(Mg0.5Ti0.5)O3 Lead‐Free Piezoceramics

Lead‐free BNT‐based piezoceramics, (1?x)Bi_0.5Na_0.5TiO₃–xBi(Mg_0.5Ti_0.5)O₃ [(1?x)BNT–xBMT] (0.00 ≤ x ≤ 0.06) binary system, were synthesized using a conventional ceramic fabrication method. Effect of Bi(Mg_0.5Ti_0.5)O₃ (BMT) substitution on room temperature (RT) crystal structure, and temperature dependence of electric properties were investigated. The XRD indicates that a pure perovskite phase is formed. The introduction of BMT decreases E_C of BNT from 7.3 to 4.0 kV/mm, and increases d₃₃ from 58 pC/N to 110 pC/N for the x = 0.05. The system shows a typical ferroelectric (FE) polarization loop P(E) and butterfly bipolar strain‐electric S(E) curve at RT. For the composition of 0.95BNT–0.05BMT antiferroelectric (AFE) phase appears near 80°C, characterized by a constricted P(E) loop and altered bipolar S(E) butterfly, and gradually prevails with increasing temperature. Temperature dependence of dielectric constant shows that T_C increases from 310°C for pure BNT to 352°C for the x = 0.05. The results indicate that the piezoelectric properties of BNT have been improved by means of Bi(Mg_0.5Ti_0.5)O₃ substitution.     

Preparation and Electric Properties of Bi0.5Na0.5TiO3–Bi(Al0.5Ga0.5)O3 Lead‐Free Piezoceramics

A new lead‐free BNT‐based piezoelectric ceramics of (1 ? x)Bi_0.5Na_0.5TiO₃–xBi(Al_0.5Ga_0.5)O₃ (x = 0, 0.02, 0.03, 0.04, and 0.05) were synthesized using a conventional ceramic fabrication method. Their structures and electrical properties were investigated. All the samples show a typical ferroelectric P(E) loops and S(E) curves at room temperature. The optimal properties are obtained at the composition of the x = 0.03. The substitution of Bi(Al_0.5Ga_0.5)O₃ enhances piezoelectric constant and increases Curie temperature from 58 pC/N and 310°C of pure BNT to 93 pC/N and 325°C of the x = 0.03. The temperature‐dependent P(E) loops and S(E) curves of 0.97BNT–0.03BAG indicate that phase transition from ferroelectric to antiferroelectric takes place over a very wide temperature region from 80°C to 180°C. The results show that the introduction of BAG improves the electrical properties of BNT.     

Photoluminescence and Temperature Dependent Electrical Properties of Er‐Doped 0.94Bi0.5Na0.5TiO3‐0.06BaTiO3 Ceramics

Er‐doped 0.94Bi_0.5Na_0.5TiO₃‐0.06BaTiO₃ (BNT‐6BT: xEr, x is the molar ratio of Er³⁺ doping) lead‐free piezoceramics with x = 0–0.02 were prepared and their multifunctional properties have been comprehensively investigated. Our results show that Er‐doping has significant effects on morphology of grain, photoluminescence, dielectric, and ferroelectric properties of the ceramics. At room temperature, the green (550 nm) and red (670 nm) emissions are enhanced by Er‐doping, reaching the strongest emission intensity when x = 0.0075. The complex and composition‐dependent effects of electric poling on photoluminescence also have been measured. As for electrical properties, on the one hand, Er‐doping tends to flatten the dielectric constant‐temperature (ε_r‐T) curves, leading to temperature‐insensitive dielectric constant in a wide temperature range (50°C–300°C). On the other hand, Er‐doping significantly decreases the ferroelectric‐relaxor transition temperature (T_F–R) and depolarization temperature (T_d), with the T_F–R decreasing from 76°C to 42°C for x = 0–0.02. As a result, significant composition‐dependent electrical features were found in ferroelectric and piezoelectric properties at room temperature. In general, piezoelectric and ferroelectric properties tend to become weaker, as confirmed by the composition‐dependent piezoelectric coefficient (d₃₃), planar coupling factor (k_p), and the shape of polarization‐electric field (P–E), current‐electric field (J–E), bipolar/unipolar strain‐electric field (S–E) curves. Furthermore, to understand the relationship between the T_F–R/T_d and the electrical properties, the composition of x = 0.0075 has been intensively studied. Our results indicate that the BNT‐6BT: xEr with appropriate Er‐doping may be a promising multifunctional material with integrated photoluminescence and electrical properties for practical applications.     

The Composition and Temperature‐Dependent Structure Evolution and Large Strain Response in (1−x)(Bi0.5Na0.5)TiO3−xBa(Al0.5Ta0.5)O3 Ceramics

The (1?x) (Bi_0.5Na_0.5)TiO₃?xBa(Al_0.5Ta_0.5)O₃((1?x)BNT‐xBAT) lead‐free piezoceramics was fabricated using a conventional solid‐state reaction method. The temperature and composition‐dependent strain behavior, dielectric, ferroelectric (FE), piezoelectric, and pyroelectric properties have been systematically investigated to develop lead‐free piezoelectric materials with large strain response for actuator application. As the BAT content increased, the FE order is disrupted resulting in a degradation of the remanent polarization, coercive field, and the depolarization temperature (T_d). A large strain of 0.36% with normalized strain d₃₃* = 448pm/V was obtained for the optimum composition x = 0.045 at room temperature. The bipolar and unipolar strains for the compositions x = 0.035 and x = 0.04 reach almost identical maximum values when the temperature is in the vicinity of their respective depolarization temperature (T_d). The Raman‐spectra analysis, macroscopic properties, thermal depolarization results, and temperature‐dependent relationships of both polarization and strain demonstrated that the origin of the large strain response for this investigated system is attributed to a field‐induced relaxor to FE phase transformation.     

Large Piezoresponse and Ferroelectric Properties of (Bi0.5Na0.5)TiO3–(Bi0.5K0.5)TiO3–Bi(Mg0.5Ti0.5)O3 Thin Films Prepared by Chemical Solution Deposition

Bulk ceramic 72.5 mol%(Bi_0.5Na_0.5)TiO₃–22.5 mol%(Bi_0.5K_0.5)TiO₃–5 mol%Bi(Mg_0.5Ti_0.5)O₃ (BNT–BKT–BMgT) has previously been reported to show a large high‐field piezoelectric coefficient (d₃₃* = 570 pm/V). In this work, the same composition was synthesized in thin film embodiments on platinized silicon substrates via chemical solution deposition. Overdoping of volatile cations in the precursor solutions was necessary to achieve phase‐pure perovskite. An annealing temperature of 700°C resulted in good ferroelectric properties (P_max = 52 μC/cm² and P_r = 12 μC/cm²). Quantitative compositional analysis of films annealed at 650°C and 700°C indicated that near ideal atomic ratios were achieved. Compositional fluctuations observed through the film thickness were in good agreement with the existence of voids formed between successive spin‐cast layers, as observed with electron microscopy. Bipolar and unipolar strain measurements were performed via double laser beam interferometry and a high effective piezoelectric coefficient (d_33,f) of approximately 75 pm/V was obtained.     

ZnO‐enhanced electrical properties of Bi0.5Na0.5TiO3‐based incipient ferroelectrics

Bi_0.5Na_0.5TiO₃‐based incipient ferroelectrics with pseudocubic structure generally show weak ferro‐/piezoelectricity but giant field‐induced strains. It is difficult to artificially and smoothly improve the electrical property based on conventional chemical doping or substituting without changing the crystal structure and suppressing the strain. Here, by introducing the semiconductor ZnO into the lead‐free incipient ferroelectric ((Bi_0.5(Na_0.84K_0.16)_0.5)_0.96Sr_0.04)(Ti_0.975Nb_0.025)O₃ (BNT–2.5Nb) to form 0‐3 type composites (BNT–2.5Nb:xZnO), we experimentally illustrate that the resistance and ferro‐/piezoelectric properties can be enhanced significantly with an unchanged crystal structure and only slightly suppressed strains. For example, the remanent polarization and piezoelectric coefficient increase from 4.6 μC/cm² and 8 pC/N for x=0 to 9.0 μC/cm² and 31 pC/N for x=0.3. At the same time, the total strain only decreases from 0.140% for x=0 to 0.108% for x=0.3, whereas the negative strain increases from ?0.003% for x=0 to ?0.010% for x=0.3. And the thermal stability of d₃₃ is enhanced. The corresponding mechanism is attributed to that ZnO can form a local field, preventing the depolarization of field induced macroscopic ferroelectric domains. Our results not only provide a feasible way to tune electrical properties of BNT‐based incipient ferroelectrics, but also may stimulate further work on artificially structured high‐performance ferroelectrics.     

Piezoelectric Property and Strain Behavior of Pb(Yb0.5Nb0.5)O3–PbHfO3–PbTiO3 Polycrystalline Ceramics

(1?x)Pb(Hf_1?yTi_y)O₃–xPb(Yb_0.5Nb_0.5)O₃ (x = 0.10–0.44, y = 0.55–0.80) ceramics were fabricated. The morphotropic phase boundary (MPB) of the ternary system was determined by X‐ray powder diffraction. The optimum dielectric and piezoelectric properties were achieved in 0.8Pb(Hf_0.4Ti_0.6)O₃–0.2Pb(Yb_0.5Nb_0.5)O₃ ceramics with MPB composition, where the dielectric permittivity ε_r, piezoelectric coefficient d₃₃, planar electromechanical coupling k_p, and Curie temperature T_c were found to be on the order of 1930,480 pC/N, 62%, and 360°C, respectively. The unipolar strain behavior was evaluated as a function of applied electric field up to 50 kV/cm to investigate the strain nonlinearity and domain wall motion under large drive field, where the high field piezoelectric d₃₃* was found to be 620 pm/V for 0.82Pb(Hf_0.4Ti_0.6)O₃–0.18Pb(Yb_0.5Nb_0.5)O₃. In addition, Rayleigh analysis was carried out to study the extrinsic contribution, where the value was found to be in the range 2%–18%.     

Enhanced insulating and piezoelectric properties of BiFeO3-BaTiO3-Bi0.5Na0.5TiO3 ceramics with high Curie temperature

BiFeO₃-BaTiO₃ ceramics are promising lead-free piezoelectric ceramics due to their high piezoelectric properties and high Curie temperature, but their high leakage current density makes the poling difficult. In this study, a decreased leakage current density by three orders of magnitude was obtained in Bi_0.5Na_0.5TiO₃ (BNT) added 0.67BiFeO₃-0.33BaTiO₃ (BF-BT) ceramics. It was found that the largely improved insulating properties benefit from the reduced oxygen vacancies and weak reduction of Fe³⁺ to Fe²⁺ as confirmed by photoluminescence and X-ray photoelectron spectroscopy measurements, thereby contributing to high-temperature and high-field poling. In addition, the introduction of BNT leaded to increased grain size. Due to the grown grains as well as reduced oxygen vacancies and Fe²⁺, enhanced insulating and optimal piezoelectric properties with P_r = 24.2 µC/cm², d₃₃ = 183 pC/N, k_p = 0.28, and T_C = 467°C were achieved in BF-BT-0.05BNT ceramics.     

Large Electromechanical Strain in Lead‐Free Binary System K0.5Bi0.5TiO3‐Bi(Mg0.5Ti0.5)O3

Solid solution formation in the lead‐free binary system (1?x)K_0.5Bi_0.5TiO₃?xBi(Mg_0.5Ti_0.5)O₃ has been studied for compositions x ≤ 0.12. X‐ray powder diffraction shows single‐phase perovskite for x < 0.1, and a mixed phase region between tetragonal and pseudocubic phases for compositions 0.04 ≤ x ≤ 0.06. Large electromechanical strains of ~0.3% at fields of 50 kV/cm are recorded in the mixed phase region, with d₃₃* (S_max/E_max) values of ~600 pm/V. The materials sustain polarization at low electric fields with remnant polarization ~18 μC/cm² and coercive field ~20 kV/cm for x = 0.06. Relative permittivity‐temperature plots display relaxor characteristics, with peak temperature ~340°C.     

Large E-field induced strain and polar evolution in lead-free Zr-doped 92.5%(Bi0.5Na0.5)TiO3–7.5%BaTiO3 ceramics

Structure, dielectric permittivity, strain, electric (E) polarization, and piezoelectric responses of (Bi_1/2Na_1/2)_0.925Ba_0.075(Ti_1−xZr_x)O₃ (BNT7.5BT-100xZr; x = 0–0.04) ceramics were investigated as functions of poling E field and temperature. The BNT7.5BT ceramic reveals a phase transition from P4bm nanodomains to long-range-ordered P4mm domains. The Zr-doped BNT7.5BT ceramic reveals a reversible change of unit cell with dynamically fluctuating polar nanoregions, which are responsible for the large strain. The poled BNT7.5BT ceramic displays a depolarization temperature of T_d = 90 °C, which correspond to a phase transition from ferroelectric to relaxor states. The Zr-doped BNT7.5BT ceramics have Burns temperatures (T_B) in the region of 400–435 °C, below which polar nanoregions begin to develop. The Zr-doped BNT7.5BT ceramics display wide diffuse phase transitions, suggesting a transition from R + T to T phases. BNT7.5BT-2Zr ceramic shows a temperature dependent linear large strain of 0.482% at 150 °C and can be a potential candidate for lead-free actuator.     

Temperature‐Insensitive High Strain in Lead‐Free Bi0.5(Na0.84K0.16)0.5TiO3–0.04SrTiO3 Ceramics for Actuator Applications

Lead‐free piezoelectric ceramics, 0.96[{Bi_0.5 (Na_0.84K_0.16)_0.5}_1?xLi_x(Ti_1?yNb_y)O₃]–0.04SrTiO₃ (BNKLiTN–ST) with x, y = 0–0.030, were synthesized by solid‐state reaction method. X‐ray diffraction patterns indicated that Li and Nb successfully diffused into the BNKT–ST lattice and formed a pure perovskite structure with x, y ≤ 0.025. Increasing the Li and Nb contents (x, y = 0.020) induced a phase transformation from the coexistent rhombohedral–tetragonal phases for pure BNKT–ST ceramics to a pseudocubic phase, resulting in degradation of the remnant polarization and coercive field. However, the field‐induced strain was markedly enhanced at x, y = 0.020, giving rise to a giant dynamic piezoelectric constant (d₃₃* = S_max/E_max = 800 pm/V). Furthermore, the temperature dependence of the field‐induced strain response showed temperature‐insensitivity up to 120°C. To explore its potential for device applications, a 10‐layered stack‐type multilayer actuator was fabricated from the optimal composition (x, y = 0.020). This actuator showed a large S_max/E_max of 600 pm/V at a relatively low driving field of 4.5 kV/mm suggesting highly promising results in lead‐free BNT‐based ceramics.     

Mn doping effects on electric properties of 0.93(Bi0.5Na0.5)TiO3‐0.07Ba(Ti0.945Zr0.055)O3 ceramics

The validity of Mn element on 0.93(Bi_0.5Na_0.5)TiO₃‐0.07Ba(Ti_0.945Zr_0.055)O₃ ceramics (BNT‐BZT‐xMn) is certified by doping. On account of multiple effects introduced by Mn, the appropriate Mn content facilitates property improvement effectively. Compared with pure BNT‐BZT, d₃₃ of the component x = 0.25 increases about 8% up to 187 pC/N and Q_m of the component x = 1 increases about 84% up to 197. Thermally stimulated depolarization currents (TSDC) measurement reveals Mn additive is helpful to pyroelectric properties as well. The Mn‐doped component x = 0.125 exhibits better pyroelectric performance at room temperature. Corresponding pyroelectric coefficient and the figures of merit reach up to 0.061 μC/(cm² °C), F_i=217 pm/V, F_ν = 0.023 m²/C, and F_d = 12.6 μPa^?1/2, respectively, even superior to lead‐based ceramics. Similar pyroelectric advantage is also observed in the component x = 0.5 near depolarization temperature T_d. Mn doping has slight harmful influence on the ferroelectric‐to‐relaxor transition temperature T_F?R, as well as T_d, but hardly shows restriction on application. These results confirm Mn doping is an available strategy to improve BNT‐based ceramics. Therefore, Mn‐doped BNT‐BZT ceramics will be excellent candidates in area of high‐power piezoelectric application and pyroelectric detectors.     

Piezoelectric Properties of a Pioneering 3‐1 Type PZT/Epoxy Composites Based on Freeze‐Casting Processing

Lead zirconate titanate (PbZr_1 ? xTi_xO₃, PZT)/epoxy composites with one‐ dimensional epoxy in PZT matrix (called 3‐1 type piezocomposites) have been fabricated by tert‐butyl alcohol (TBA)‐based directional freeze casting of PZT matrix and afterward infiltration of epoxy. The composites with PZT volume fraction ranging from 0.36 to 0.69 were obtained by adjusting initial solid loading in freeze‐casting slurry. The effect of poling voltage on piezoelectric properties of the composites was studied for various volume fraction of PZT phase. With the increasing of PZT volume fraction, relative permittivity (ε_r) increased linearly and piezoelectric coefficient (d₃₃ and d₃₁) increased step by step. The resultant composites with 0.57 PZT volume fraction possessed the highest hydrostatic piezoelectric strain coefficient (d_h) value (184 pC/N), voltage coefficient (g_h) value (13.6 × 10^?3 V/m Pa), and hydrostatic figure of merit (HFOM) value (2168 × 10^?15 Pa^?1).     

Dielectric Relaxor Evolution and Frequency‐Insensitive Giant Strains in (Bi0.5Na0.5)TiO3‐Modified Bi(Mg0.5Ti0.5)O3–PbTiO3 Ferroelectric Ceramics

The 0.45Bi(Mg_0.5Ti_0.5)O₃–(0.55 ? x)PbTiO₃–x(Bi_0.5Na_0.5)TiO₃ (BMT–PT–xBNT) ternary solid solution ceramics were prepared via a conventional solid‐state reaction method; the evolution of dielectric relaxor behavior and the electrostrain features were investigated. The XRD and dielectric measurements showed that all studied compositions own a single pseudocubic perovskite structure and undergo a diffuse‐to‐relaxor phase transition owing to the evolution of the domain from a frozen state to a dynamic state. The formation of the above dielectric relaxor behavior was further confirmed by a couple of measurements such as polarization loops, polarization current density curves, as well as bipolar strain loops. A large strain value of ~0.41% at a driving field of 7 kV/mm (normalized strain d₃₃* of ~590 pm/V) was obtained at room temperature for the composition with x = 0.32, which is located near the boundary between ergodic and nonergodic relaxor. Moreover, this electric field‐induced large strain was found to own a frequency‐insensitive characteristic.     

Lead-free Na0.4K0.1Bi0.5TiO3 ceramic: Poling effect and enhancement in electromechanical and piezoelectric voltage coefficient

The effect of electric poling on the piezoelectric properties of the sintered Na_0.4K_0.1Bi_0.5TiO₃ is studied with varying poling field and temperature. An optimized poling condition (E_P =50 kVcm, T_P =110 °C) exhibited a high piezoelectric voltage (g₃₃∼ 85 mV m/N) and charge coefficients (d₃₃∼193pC/N). A combination of electric field induced irreversible transformation from polar nano regions embedded in a non-polar relaxor state to a long-range ordered ferroelectric state and increase in the structural ordering are responsible for the observed high piezoelectric properties. A mechanism is discussed to reveal the origin of high voltage coefficient due to poling, where the decrease of dielectric permittivity can facilitate high g₃₃. This investigation provides an approach for designing the high performance Na_0.4K_0.1Bi_0.5TiO₃based materials suitable for sensors and energy harvesting applications.     

Dielectric and Piezoelectric Properties of (1−x)K0.5Bi0.5TiO3–xBa(Ti0.8Zr0.2)O3 Ceramics

The properties of relaxor ceramics in the compositional series (1?x)K_0.5Bi_0.5TiO₃–xBa(Ti_0.8Zr_0.2)O₃ have been investigated. Values of T_m, the temperature of maximum relative permittivity, decreased from 380°C at x = 0.0 to below room temperature for x > 0.7. Compositions x = 0.1 and 0.2 were piezoelectric and ferroelectric. The maximum value of d₃₃ piezoelectric charge coefficient, 130 pC/N, and strain, 0.14%, occurred at x = 0.1. Piezoelectric properties of x = 0.1 were retained after thermal cycling from room temperature to 220°C, consistent with results from high‐temperature X‐ray diffraction indicating a transition to single‐phase cubic at ~300°C.     

The Relationship Between Phase Structure and Electrical Properties in (1 − x)(Bi0.5Na0.5TiO3–Ba0.5K0.5TiO3–BaTiO3)‐ xK0.5Na0.5NbO3 Quaternary Lead‐Free Piezoelectric Ceramics

(1 ? x)(0.85Bi_0.5Na_0.5TiO₃–0.11Ba_0.5K_0.5TiO₃–0.04BaTiO₃)‐ xK_0.5Na_0.5NbO₃ lead‐free piezoelectric ceramics with x = 0.00, 0.02, 0.03, 0.04, 0.05, and 0.10 were prepared by a conventional solid state method. A coexistence of rhombohedral (R) and tetragonal (T) phases was found in the system, which tended to evolve into pseudocubic symmetry when x increases. The x = 0.04 sample exhibited improved electrical properties: the dielectric constant ε_r = 1900 with the low loss tangents 0.06, the S_max/E_max of ~400 and ~460 pm/V under unipolar and bipolar electric field, respectively. Meanwhile, piezoelectric constant d₃₃ still maintained ~160 pC/N. These could be owed to the formation of polar nanoregions for relaxor phase.     

Enhanced Piezoelectric Properties and Thermal Stability in the (K0.5Na0.5)NbO3:ZnO Lead‐Free Piezoelectric Composites

The piezoelectric properties of (K_0.5Na_0.5)NbO₃ (KNN) are normally enhanced by chemical substitutions or doping to form solid solutions. In this study, we report that the piezoelectric properties of KNN and thermal stability of piezoelectric coefficient d₃₃ can be both enhanced by forming the composite of KNN:ZnO. The d₃₃ of KNN:0.2ZnO can be improved to 110 pC/N by introducing the ZnO nanoparticles, which is better than the pure KNN (d₃₃ = 85 pC/N). The Curie temperature (T_C = 407°C) remains well comparable to the pure KNN (T_C = 408°C). Furthermore, the thermal stability of both remanent polarization (P_r) and piezoelectric parameter (d₃₃) is improved. The enhanced thermal stability could be related to the induced built‐in electric field or the enhanced sinterability by the addition of ZnO. The present results may help to optimize the piezoelectric properties of lead‐free materials by forming composite.     

Characterization of the High‐Temperature Ferroelectric (100−x−y)BiScO3–(x)Bi(Zr0.5Zn0.5)O3–(y)PbTiO3 Perovskite Ternary Solid Solution

Ternary compositions based on Bi(B′B″)O₃–PbTiO₃‐type compounds have been investigated for high‐temperature piezoelectric applications. Compositions in the ternary were chosen to be near the binary morphotropic phase boundary (MPB) composition of BiScO₃–PbTiO₃ (BS–PT). Ternary compositions in (100?x?y)BiScO₃–(x)Bi(Zr_0.5Zn_0.5)O₃–(y)PbTiO₃ [(100?x?y)BS–xBZZ–yPT] have been investigated with x ≤ 7.5. For compositions with x > 10, the Curie temperature (T_C) decreased below 400°C. Dielectric, piezoelectric, and electromechanical properties were characterized as a function of temperature, frequency, and electric field. Small additions of BZZ were shown to increase the electromechanical properties with only a small loss in T_C. The electromechanical properties were temperature stable up to the depoling temperature. The most promising composition exhibited a T_C of 430°C, piezoelectric coefficient (d₃₃) of 520 pC/N, and a planar coupling factor (k_p) of 0.45 that remained unchanged up to depoling temperature at 385°C.