凝胶相转化温度和空气预蒸发时间对PVDF超滤膜性能及结构的影响

利用非溶剂相转化法(NIPS),以聚偏氟乙烯(PVDF)/聚乙烯吡咯烷酮(PVP)/N,N-二甲基乙酰胺( DMAC)为铸膜液体系,水为凝固浴制备了大通量超滤膜.考察了铸膜液温度、凝胶浴温度、空气预蒸发时间等条件对超滤膜性能与结构的影响.研究结果显示,随着铸膜液和凝胶浴温度的提高,膜纯水通量增大,强度增强,截留率降低,膜的第一泡点压力减小,膜的孔隙率随铸膜液温度升高而增大,随凝胶浴温度升高先增大后减小,膜断面指状孔发育较为通透,海绵层致密.延长铸膜液在空气预蒸发时间,膜的第一泡点压力和孔隙率降低,超滤膜截留率提高,通量和强度变化不大.     

凝胶浴条件对PVDF/CaCO3共混中空纤维膜性能和结构的影响

采用干-湿相转化法制备了PVDF/CaCO3共混中空纤维膜,考察了芯液组成和外凝胶浴温度对共混膜结构和性能的影响。结果表明,随芯液中酸含量增加,膜纯水通量迅速升高,BSA截留率略有下降;膜拉伸强度下降,断裂伸长率增加。SEM图显示,膜断面指状孔的数量增多、支撑层厚度变薄、膜亚层海绵孔增加;相应孔隙率升高,而泡点压力略微下降。当外凝胶浴温度较高时,膜支撑层和外皮层较为致密,导致膜纯水通量明显下降,同时BSA截留率在80℃高温外凝胶浴时,由于膜外皮层上出现少量大孔结构,而迅速下降为62.55%。     

聚砜中空纤维膜的制备及其结构与性能研究

以低分子量聚乙二醇(PEG)为添加剂,二甲基乙酰胺(DMAC)为溶剂,采用纺丝及浸没沉淀相转化法制备了聚砜(PSU)中空纤维膜,考察了PEG含量和空气间隙对膜结构及性能的影响。实验结果表明,随着PEG含量的增加,PSU铸膜溶液的黏度增大,所得膜结构从指状孔向海绵孔转变,膜变得致密,膜的孔隙率和纯水通量降低,牛血清白蛋白(BSA)截留率和拉伸强度提高;但当PEG含量继续增加时,尽管孔隙率继续下降,但膜截面孔径增大,膜的纯水通量反而有所回升,相应的BSA截留率下降。当空气间隙较短时,膜的结构基本没有变化,但当空气间隙达到7 cm时,膜截面出现指状孔,膜变得相对疏松;随空气间隙的增加,膜的纯水通量上升,BSA截留率总体下降。当PEG与DMAc的质量比为35/45,空气间隙为5 cm时,膜的综合性能最好,其纯水通量为129.0 L/(m2·h),BSA截留率为96.8%,孔隙率为75.5%,拉伸强度为5.01 MPa。     

DMI增塑二醋酸纤维素超滤膜的制备与性能研究

以绿色环保的1,3-二甲基-2-咪唑啉酮(DMI)为增塑剂,采用复合热致相分离法制备了二醋酸纤维素(CDA)超滤膜。通过扫描电子显微镜(SEM)观察以及纯水通量、牛血清白蛋白(BSA)截留率、孔隙率和拉伸强度等测试,研究了CDA固含量对超滤膜结构和性能的影响。同时,通过综合比较不同固含量CDA膜的纯水通量和蛋白截留率,确定了最佳铸膜液配方。结果表明:提高CDA的固含量可以消除膜截面中的大孔结构,但同时降低了膜的孔隙率。其中,当铸膜液中CDA固含量为20%时,所制备平板膜的拉伸强度高达6.10 MPa,对0.1 g/L BSA水溶液的渗透通量为47.7 L/(m~2·h),截留率达到96.4%。     

聚偏氟乙烯管式微孔膜的工艺研究

对聚偏氟乙烯(PVDF)管式微孔膜生产工艺进行了研究。系统地讨论了相转化法制备管式微孔膜过程中各个因素的影响。研究发现,铸膜液温度对PVDF管式膜截留率和纯水通量影响不明显;铸膜液中加入NH4Cl后,膜的纯水通量增加,截留率减小,孔径增大;不同凝固浴制得的PVDF管式微孔膜不同,膜的纯水通量和截留率也不同。     

聚砜中空纤维膜的亲水改性研究

将吐温80或磺化聚砜(SPSF)加入聚砜-聚乙二醇400-二甲基乙酰胺(PSF–PEG400–DMAc)体系,共混制成均一铸膜液,采用浸入沉淀相转化法制备聚砜中空纤维超滤膜,考察吐温80或SPSF对聚砜中空纤维膜的亲水改性效果。对膜结构、铸膜液黏度、纯水通量、截留率、拉伸强度等进行了表征。研究结果表明,SPSF相比吐温80对膜的亲水性改善更明显。当SPSF质量分数为1.5%时,就可将PSF中空纤维膜的纯水通量提高一倍以上,膜纯水通量达到302 L/(m~2·h),对牛血清白蛋白(BSA)的截留率达到93%。     

铸膜液中水含量对聚砜超滤膜结构和性能的影响

试验在环境温度20℃、相对湿度50%、凝胶浴温度20℃的条件下制膜,在聚砜(PS)铸膜液中添加水为非溶剂添加剂,研究水添加量对铸膜液粘度、膜性能和结构的影响.结果表明,水的添加对铸膜液起到了增粘的作用;30℃ PS的质量分数为14%铸膜液所成膜的纯水通量随铸膜液中水的添加量的增加大体上呈增加的趋势,从59.1增大到126.4 L·m~(-2)·h~(-1);截留率则略有下降;相应的膜表面的孔径增大、孔增多;相同水添加量(质量分数0.05%)PS的质量分数为14%的铸膜液粘度随温度的升高而减小;铸膜液温度的升高,相应的膜的纯水通量随之增加,截留率则略有下降.     

聚偏氟乙烯管式微孔膜的工艺研究

对聚偏氟乙烯(PVDF)管式微孔膜生产工艺进行了研究。系统地讨论了相转化法制备管式微孔膜过程中各个因素的影响。研究发现，铸膜液温度对PVDF管式膜截留率和纯水通量影响不明显；铸膜液中加入NH4Cl后，膜的纯水通量增加，截留率减小，孔径增大；不同凝固浴制得的PVDF管式傲孔膜不同，膜的纯水通量和截留中也不同。     

1种聚偏氟乙烯中空纤维膜的制备方法等

解决了目前PVDF 中空纤维膜的永久亲水性差和机械强度差的问题,在改善亲水性和机械强度的同时保持中空纤维超滤膜的高通量和高截留率。主要实施方法为按照重量百分比组成,在反应釜中加入12%～28%聚偏氟乙烯,0.8%～6%表面活性剂,6%～30%成孔剂,38%～70%溶剂,0.1%～3%水,搅拌均匀,铸膜液过滤脱泡;铸膜液和芯液同时由纺丝喷头挤出,纺丝喷头温度为60～80℃,在确定的温度下保持温度变化幅度为±0.4℃;铸膜液在空气中以0.5～3 m/min的速度经过5～50 mm距离后进入外凝固浴中,在外凝固浴中停留时间为5～10 s,外凝固浴为30～60℃的水,在确定的温度下保持温度变化幅度为±0.2℃;得聚偏氟乙烯的中空纤维超滤膜。     

PVDF-PAN-纳米粘土杂化中空纤维超滤膜纺丝工艺研究

以聚偏氟乙烯和聚丙烯腈为主要膜材料、N,N-二甲基乙酰胺为溶剂、无水LiCl和有机纳米粘土为添加剂,采用干-湿相转化法纺丝工艺制备杂化中空纤维超滤膜,研究了干程、外凝胶浴温度、芯液温度和组成等纺丝工艺参数对杂化膜微观结构和分离性能的影响.SEM观察发现,中空纤维膜有较致密的外表面和多孔的内表面,干程对膜的横截面结构和表面形态都有影响:增加芯液含量有利于抑制大孔结构的产生,使孔径变小,结构致密,芯液为质量分数40%无水乙醇时,制得的膜对BSA截留率达到99%.试验结果表明,在较高的凝胶浴温度和较大的干程下制得的膜有较高的水通量和较低的截留率;凝胶浴温度升高,膜的力学性能加强,铸膜液中聚合物的质量分数为16%时,最大拉伸强度为3.16 MPa.     

COMPARISON OF METHODS OF ANALYSIS OF GYPSUM1

The different analytical methods proposed for the evaluation of gypsum have been subjected to an experimental test. A combination method, consisting of a fusion with KHCO₃ and determination of CaO by KMnO₄ titration, the SO₃ by Andrews method of titration of BaCrO₄ has been found to give very reliable results with the least consumption of time.     

茶多酚提取方法进展

本文综述了国内外现有茶多酚提取方法的现状以及近期的研究进展，并对其优缺点进行了评价。这将有助于中低档茶的综合利用和茶多酚的进一步开发应用。     

HEASUREHENT OF INSTANTANEOUS RATES OF LOSS OF VOIATILE COMPOUNDS DURING DRYING OF DROPS

A novel technique serves to monitor instantaneous rates of loss of a volatile solute from a suspended drop during drying. A highly sensitive electron capture detector is used to monitor concentrations of SF6 released into a flowing gas stream from a suspended, drying drop. Simultaneously, the appearance and morphological development of the drop are monitored with a video camera. This provides the wherewithal of relating instantaneous rates of loss of the volatile solute to particular events during the development of particle morphology.

Initial experiments have been carried out with drops of aqueous solutions of glucose, sucrose, maltodextrin and coffee extract. The results clearly display the onset of the volatiles-retentive selective diffusion phenomenon. There is also substantial loss of the volatile component later in the drying process, when the drops undergo repeated ex ansion, bursting and cratering due to the formation of internaf bubbles. These experiments appear to be the first quantitative demonstration of major losses accompanying changes in drop morphology.     

氢气纯度分析方法准确性的探讨

ONACCURACYOFANALYSISOFOFHYDROGEN1前言我公司目前应用的氢气纯度分析方法有两种,一种是爆炸反应法,另一种是焦性没食子酸吸收法。几年来,人们对两种分析方法的准确性曾有过褒贬不一的评论。这里我们也谈谈自己粗浅的观点。2爆炸法测定氢气纯度一定量的氢气样品与适量的空气之均匀混合物因反应后生成液体水而引起气体体积减少,减少的体积等于参加反应气体体积之和。其中l／3为氧气,2／3为氢气。根据氢气取样量和反应前后混气体体积之差,以及氢气在反应中的体积比例关系,可计算出样品的氢气纯度。计算公式式中：A一混…     

环氧树脂羟基值测定方法的研究

利用乙酸酐、吡啶和浓硫酸混合的乙酰化试剂测定环氧树脂中羟基值含量的方法具有操作简便、滴定终点明显和分析结果误差小等优点。     

骑式摩托车油箱喷涂工艺的改进

面对日益激烈的市场竞争,摩托车油箱外观质量越来越成为影响销售的因素之一。文章介绍了改进工艺后的油箱涂装,该涂装体系提高了油箱外观的丰满度,降低了油箱涂装的生产成本。     

ANALYSIS OF RECENT MEASUREMENTS OF THE VISCOSITY OF GLASSES

Viscosity of Simple Soda-Silicate 500° to 1400°C Comparison of the results given by English with those of Washburn, Shelton and Libman, indicates a discrepancy in the absolute values of log₁₀ viscosity amounting to 0.6, those of Washburn et al., being relatively too high. If correction for this is made, the isothermal curves of log₁₀ viscosity as a function of soda content are smooth up to 50% Na₂O, showing no inflection. The observations as a function of temperature T are all represented within accidental error by an equation of the type where all three constants vary regularly with the composition. Change of Viscosity of Glass (6SiO₂, 2Na₂O) due to Molecular Substitution of CaO, MgO and Al₂O₃ for Na₂O The effect is clearly brought out by plotting (from the results of English) the change of log₁₀η due to the substitution as a function of temperature. The curves each show a sharp bend at a temperature between 840° and 1050°C, which is designated the aggregation temperature T_a. If we divide these curves by the corresponding percentage substituted, we get curves for each oxide which are straight and parallel below the aggregation temperatures, the slopes (increase of change of log₁₀η per 100°C) being −0.056 (CaO), −0.055 (MgO), −0.018 (A1₂O₃) per per cent oxide substituted. For substitution of 1/2 molecule the slopes are −0.325 (CaO), −0.23 (MgO) and −0.18 (Al₂O₃) per 100°. At the aggregation temperature the change of log₁₀η per per cent is a minimum, 0.03 to 0.06 for CaO, 0.12 for MgO, 0.07 for Al₂O₃. Evidence of Aggregation in Glasses, from viscosity Measurements The sharp bends in the plots of change of log₁₀η due to substitution of an oxide for Na₂O, suggest the beginning of molecular aggregation at these temperatures. These aggregation temperatures are close to the devitrification temperatures, but the effect on the viscosity curves cannot be due to actual devitrification since it does not change with time. Taking the aggregation temperatures as equal to devitrification temperatures, additional isotherms are roughly sketched into the equilibrium triangle of the system Na₂O-CaO-SiO₂. Change of Viscosity of Glass (4SiO₂, 2Na₂O) due to of Substitution of B₂O₃ for SiO₂ The change of log₁₀η (from the results of English) is plotted as a function of temperature, and also the change of log₁₀η per per cent B₂O₃. The curves are more complex than for the substitution for Na₂O.     

SEDIMENTATION OF BINARY MIXTURES OF PARTICLES OF UNEQUAL DENSITIES AND OF DIFFERENT SIZES

A model is developed for the sedimentation from a suspension of two particle species of unequal densities and of different sizes. The composition and the thickness of various layers in the sediments are predicted using graphical and analytical methods. The model predictions were in excellent agreement with experimental results, when the particle size ratio was ≥ 108. When size ratio of the particles was 2.60 and 4.31 the agreement occurred in about 50 percent of the cases.     

典型煤碳燃烧特性研究和数值模拟

本文以三种典型煤的碳燃烧为研究对象，分别采用简单一维沉降燃烧方式和等温加热燃烧方式，实验研究了煤在快速加热条件下，其碳的初期和中，后期燃烧过程。以实验为基础，建立了煤的碳燃烧模型，变工况数值模拟了煤的碳燃烧过程，揭示了煤不同条件下的单颗粒碳燃烧特性。     

用两个形状指数表征粉煤灰颗粒形貌的研究

引用两个形状指数表征颗粒形状的概念,即先将颗粒形状近似为椭圆,再将椭圆图像分离:以圆为基准的颗粒宏观形状指数δ;以光滑椭圆为基准的颗粒轮廓凹凸度,即微观形状指数ζ。分析和发展了近似椭圆模型。并运用图像分析仪对粉煤灰、水泥样品进行实验。结果表明,粉煤灰颗粒的两个形状指数δ和ζ都大于水泥颗粒。证明粉煤灰颗粒的球形度、表面光滑度优于水泥,而且,随着粒径增大,δ和ζ呈下降趋势,表明磨制颗粒越粗。(?)粒形状越不规则。文中还运用近似椭圆模型再现了颗粒的模拟图像。