Isothermal and nonisothermal melt‐crystallization kinetics of syndiotactic polystyrene

Analyses of the isothermal and nonisothermal melt kinetics for syndiotactic polystyrene have been performed with differential scanning calorimetry, and several kinetic analyses have been used to describe the crystallization process. The regime II→III transition, at a crystallization temperature of 239°, is found. The values of the nucleation parameter K_g for regimes II and III are estimated. The lateral‐surface free energy, σ = 3.24 erg cm^?2, the fold‐surface free energy, σ_e = 52.3 ± 4.2 erg cm^?2, and the average work of chain folding, q = 4.49 ± 0.38 kcal/mol, are determined with the (040) plane assumed to be the growth plane. The observed crystallization characteristics of syndiotactic polystyrene are compared with those of isotactic polystyrene. The activation energies of isothermal and nonisothermal melt crystallization are determined to be ΔE = ?830.7 kJ/mol and ΔE = ?315.9 kJ/mol, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2528–2538, 2002     

Crystallization of poly(3‐hydroxybutyrate) with stereocomplexed polylactide as biodegradable nucleation agent

Crystallization kinetics behavior and morphology of poly(3‐hydroxybutyrate) (PHB) blended with of 2–10 wt% loadings of poly(L ‐ and D ‐lactic acid) (PLLA and PDLA) stereocomplex crystallites, as biodegradable nucleating agents, were studied using differential scanning calorimetry, polarizing‐light optical microscopy (POM), and wide‐angle X‐ray diffraction (WAXD). Blending PLLA with PDLA at 1:1 weight ratio led to formation of stereocomplexed PLA (sc‐PLA), which was incorporated as small crystalline nuclei into PHB for investigating melt‐crystallization kinetics. The Avrami equation was used to analyze the isothermal crystallization of PHB. The stereocomplexed crystallites acted as nucleation sites in blends and accelerated the crystallization rates of PHB by increasing the crystallization rate constant k and decreasing the half‐time (t_1/2). The PHB crystallization was nucleated most effectively with 10 wt% stereocomplexed crystallites, as evidenced byPOM results. The sc‐PLA complexes (nucleated PHB crystals) exhibit much small spherulite sizes but possess the same crystal cell morphology as that of neat PHB based on the WAXD result. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Effect of nucleating agents on the crystallization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

The effect of nucleating agents on the crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) was studied. A differential scanning calorimeter was used to monitor the energy of the crystallization process from the melt and melting behavior. During the crystallization process from the melt, nucleating agent led to an increase in crystallization temperature (T_c) of PHBV compared with that for plain PHBV (without nucleating agent). The melting temperature of PHBV changed little with addition of nucleating agent. However, the areas of two melting peaks changed considerably with added nucleating agent. During isothermal crystallization, dependence of the relative degree of crystallization on time was described by the Avrami equation. The addition of nucleating agent caused an increase in the overall crystallization rate of PHBV, but did not influence the mechanism of nucleation and growth of the PHB crystals. The equilibrium melting temperature of PHBV was determined as 187°C. Analysis of kinetic data according to nucleation theories showed that the increase in crystallization rate of PHBV in the composite is due to the decrease in surface energy of the extremity surface. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2145–2152, 2002     

Effect of nucleating agent addition on crystallization of isotactic polypropylene

The isothermal and nonisothermal crystallization kinetics of nonnucleated and nucleated isotactic polypropylene (iPP) were investigated by DSC and a polarized light microscope with a hot stage. Dibenzylidene sorbitol (DBS) was used as a nucleating agent. It was found that the crystallization rate increased with the addition of DBS. The influence of DBS on fold surface energy, σ_e, was examined by the Hoffman and Lauritzen nucleation theory. It showed that σ_e decreased with the addition of DBS, suggesting that DBS is an effective nucleating agent for iPP. Ozawa's theory was used to study the nonisothermal crystallization. It was found that the crystallization temperature for the nucleated iPP was higher than that for nonnucleated iPP. The addition of DBS reduced the Ozawa exponent, suggesting a change in spherulite morphology. The cooling crystallization function has a negative exponent on the crystallization temperature. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2089–2095, 1998     

Crystallization kinetics of a PEEK/LCP blend

The crystallization kinetics of a polyetheretherketone (PEEK)/liquid crystalline polymer (LCP) blend was studied by using differential scanning calorimetry. Nonisothermal runnings were performed on heating and on cooling at different rates. Isothermal crystallization experiments at 315, 312, 310, and 307°C, from the melt state (380°C) were performed in order to calculate the Avrami parameters n and k and the fold surface free energy, σ_e. Polarized light optical micrographs were also obtained to confirm the Avrami predictions. It was observed that the LCP retarded the PEEK crystallization process and that the PEEK melting temperature decreased with the amount of LCP, but the LCP melting temperature increased with the amount of PEEK. Probably the PEEK improves the perfection of the LCP crystalline domains. A spherulitic morphology in pure PEEK and its blends was predicted by the Avrami analysis; however this morphology was only observed for pure PEEK and for the 80/20 composition. The other compositions presented a droplet and fibrillar-like morphology. The overall crystallization rate was observed to decrease with the crystallization temperature for all compositions. Finally, σ_e was found to decrease with the increase of LCP in the blends, having unrealistic negative values. Thus, calculations were made assuming σ_e constant at all compositions. It was observed that δ, the interfacial lateral free energy, decreased but still remained positive. It was concluded that in these blends neither σ_e nor σ could be considered constant. © 1995 John Wiley & Sons, Inc.     

Evolution of phase morphology and ‘network‐like’ structure of multiwall carbon nanotubes in binary polymer blends during melt‐mixing

Polyamide6 (PA6)/acrylonitrile butadiene styrene copolymer (ABS) blends with unmodified multiwall carbon nanotubes (MWNTs) were prepared via melt‐blending in a conical twin‐screw micro‐compounder with varying melt‐mixing time. To improve the state of dispersion of MWNTs, non‐covalent organic modifiers for MWNTs have been utilized: sodium salt of 6‐amino hexanoic acid (Na‐AHA) and 1‐pyrene‐carboxaldehyde (PyCHO). PA6/ABS blends with MWNTs have shown a phase morphology transition from ‘matrix‐dispersed droplet’ type to ‘co‐continuous’ type as a function of melt‐mixing time with the exception of 40/60 PA6/ABS blend with PyCHO‐modified MWNTs. Non‐isothermal crystallization studies revealed the heterogeneous nucleating action of MWNTs through the presence of double crystallization exothermic peaks (at ～192^°C and >200^°C) while pure PA6 shows bulk crystallization peak at ～192°C. 40/60 and 60/40 (wt/wt) PA6/ABS blends with 5 wt% unmodified MWNTs exhibited electrical conductivity values of ～3.9 × 10^?11 S/cm and ～4.36 × 10^?6 S/cm, respectively. A significant enhancement in electrical conductivity was observed with Na‐AHA and PyCHO‐modified MWNTs (order of ～10^?6 and ～10^?4 S/cm, respectively). POLYM. ENG. SCI., 55:429–442, 2015. © 2014 Society of Plastics Engineers     

Characterization of polyhydroxybutyrate biosynthesized from crude glycerol waste using mixed microbial consortia

This study focused on the characterization of polyhydroxybutyrate (PHB) produced from crude glycerol (CG) using mixed microbial consortia (MMC). PHB recovered from two biomass drying treatments (65°C oven drying and lyophilization) was characterized comparatively along with a commercially sourced PHB (PHB‐C). Characterization results showed that oven‐drying method caused PHB partial hydrolysis, as indicated by its lower molecular weight (M_w) (PHB‐O, 144,000 g mol^?1), which further affected its physical and chemical properties. Lyophilization helped alleviate PHB hydrolysis during drying process, leading to PHB (PHB‐L) of higher M_w (309,000 g mol^?1) and material properties comparable with commercial PHB. Furthermore, crystallization and morphological studies showed that PHB‐L featured faster crystallization rates and smaller spherulites as compared with PHB‐C, probably due to its lower M_w. In general, the results from this study suggested that CG‐MMC‐derived PHB‐L possessed material properties comparable with those of pure substrate/culture produced PHB. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Biodegradable polymer blends of poly(3-hydroxybutyrate) and starch acetate

The thermal behaviour and phase morphology of poly(3-hydroxybutyrate) (PHB) and starch acetate (SA) blends have been studied by differential scanning calorimetry, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy and polarizing optical microscopy. PHB/SA blends were immiscible. The melting temperatures of PHB in the blends showed some shift with increase of SA content. The melting enthalpy of the PHB phase in the blend was close to the value for pure PHB. The glass transition temperatures of PHB in the blends remained constant at 9°C. The FTIR absorptions of hydroxyl groups of SA and carbonyl groups of PHB in the blends were found to be independent of the second component at 3470cm^-1 and 1724cm^-1, respectively. The crystallization of PHB was affected by the addition of the SA component both from the melt on cooling and from the glassy state on heating. The temperature and enthalpy of non-isothermal crystallization of PHB in the blends were much lower than those of pure PHB. The crystalline morphology of PHB crystallized from the melt under isothermal conditions varied with SA content. The cold crystallization peaks of PHB in the blends shifted to higher temperatures compared with that of pure PHB. ©1997 SCI     

Isothermal crystallization behavior of polyoxymethylene with and without nucleating agents

Nucleation effects of two silicate nucleating agents, attapulgite and diatomite, on the crystallization of polyoxymethylene (POM), were studied by means of differential scanning calorimetry and polarized optical microscopy. The crystallization kinetics of POM with and without nucleating agents was analyzed by means of two isothermal crystallization kinetic equations through the crystallization thermograms. Compared with virgin POM, POM with nucleating agents of attapulgite and diatomite decreased the spherulitic size of POM and interfacial free energies per unit area perpendicular σ_e. The crystallization growth rate was accelerated because of nucleating agents as well. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 304–310, 2001     

Isothermal crystallization of iPP in model glass-fiber composites

Isothermal crystallization of iPP in model glass-fiber composites is studied by DSC, and the basic energetic parameters of crystallization are determined. Unsized untreated and thermally treated glass fibers are used in model composites to determine the role of the surface on nucleation and crystallization processes. Thermally treated glass fibers are found to exhibit a predominant nucleating effect as compared to unsized untreated ones, and the crystallization proceeds faster, resulting in lower values for the half-time of crystallization (10–120 s). The energy of formation of a nuclei of critical dimensions at a given T_c is also lower, and it decreases as the content of the fibers in the composite increases. The surface free energy of folding, σ_e = 140 × 10⁻³ J/m², was determined for iPP in the composite containing 50% glass fibers, while for pure iPP, σ_e = 170 × 10⁻³J/m² was found. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 381–389, 1998     

Crystallization behavior of poly(lactide)/poly(β‐hydroxybutyrate)/talc composites

The morphology and miscibility of commercial poly(lactide) (PLA)/poly(β‐hydroxybutyrate) (PHB, from 5 to 20 wt %) blends prepared by melt extrusion method, were investigated using differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR) observations. The results show that for all the studied blend contents, PLA/PHB blends are immiscible. The effects of PHB and talc on the nonisothermal cold crystallization kinetics of PLA were examined using a differential scanning calorimetry (DSC) at different heating rates. PHB acted as a nucleating agent on PLA and the addition of talc to the blend yielded further improvement, since significant increase in the enthalpy peak was observed for samples containing 10 wt % PHB and talc (from 0.5 to 5 phr). The crystallization kinetics were then examined using the Avrami–Jeziorny and Liu–Mo approach. The simultaneous presence of PHB and talc induced a decrease of the crystallization half time. The evolution of activation energies determined with Kissinger's equation suggests that blending with PHB and incorporating talc promote nonisothermal cold crystallization of PLA. The synergistic nucleating effect of PHB and talc was also observed on isothermal crystallization of PLA from the melt. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Crystallization behaviour of cellulose acetate butylate/poly(butylene succinate)‐co‐(butylene carbonate) blends

The kinetics of the isothermal crystallization process from the melt of pure poly(butylene succinate)‐co‐(butylene carbonate) (PBS‐co‐BC) and its blends with cellulose acetate butylate (CAB) (10–30 wt%) was studied by differential scanning calorimetry (DSC) and the well‐known Avrami equation. In the blends, the overall crystallization rate of PBS‐co‐BC became slower with increasing CAB content. The equilibrium melting temperature ( ) of PBS‐co‐BC decreased with increasing CAB content, which was similar to that with other miscible crystalline/amorphous polymer blends. The slower crystallization kinetics of PBS‐co‐BC in the blends was explicable in terms of a diluent effect of the CAB component. By application of Turnbull–Fisher kinetic theory for polymer–diluent blend systems, the surface free energy (σ_e) of pure PBS‐co‐BC and of the blends was obtained, indicating that the blend with CAB resulted in a decrease in the surface free energy of folding of PBS‐co‐BC lamellar crystals. Copyright © 2006 Society of Chemical Industry     

Stereocomplex formation between poly(L‐lactic acid) and poly(D‐lactic acid) with disproportionately low and high molecular weights from the melt

Poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) with very different weight‐average molecular weights (M_w) of 4.0 × 10³ and 7.0 × 10⁵ g mol^?1 (M_w(PDLA)/M_w(PLLA) = 175) were blended at different PDLA weight ratios (X_D = PDLA weight/blend weight) and their crystallization from the melt was investigated. The presence of low molecular weight PLLA facilitated the stereocomplexation and thereby lowered the cold crystallization temperature (T_cc) for non‐isothermal crystallization during heating and elevated the radial growth rate of spherulites (G) for isothermal crystallization, irrespective of X_D. The orientation of lamellae in the spherulites was higher for the neat PLLA, PDLA and an equimolar blend than for the non‐equimolar blends. It was found that the orientation of lamellae in the blends was maintained by the stereocomplex (SC) crystallites. Although the G values are expected to decrease with an increase in X_D or the content of high‐molecular‐weight PDLA with lower chain mobility compared with that of low‐molecular‐weight PLLA, G was highest at X_D = 0.5 where the maximum amount of SC crystallites was formed and the G values were very similar for X_D = 0.4 and X_D = 0.6 with the same enantiomeric excess. This means that the effect of SC crystallites overwhelmed that of chain mobility. The nucleating mechanisms of SC crystallites were identical for X_D = 0.1–0.5 in the T_c range 130–180 °C. Copyright © 2011 Society of Chemical Industry     

Isothermal crystallization and melting behavior of polypropylene with lanthanum complex of cyclodextrin derivative as a β‐nucleating agent

A novel highly active β‐nucleating agent, β‐cyclodextrin complex with lanthanum (β‐CD‐MAH‐La), was introduced to isotactic polypropylene (iPP). Its influence on isothermal crystallization and melting behavior of iPP was investigated by differential scanning calorimeter (DSC), wide‐angle X‐ray diffraction (WAXD), and polarized light microscopy (PLM). WAXD results demonstrated that β‐CD‐MAH‐La was an effective β‐nucleating agent, with β‐crystal content of iPP being strongly influenced by the content of β‐CD‐MAH‐La and the isothermal crystallization temperature. The isothermal crystallization kinetics of pure iPP and iPP/β‐CD‐MAH‐La was described appropriately by Avrami equation, and results revealed that β‐CD‐MAH‐La promoted heterogeneous nucleation and accelerated the crystallization of iPP. In addition, the equilibrium melting temperature (T) of samples was determined using linear and nonlinear Hoffman‐Weeks procedure. Finally, the Lauritzen‐Hoffman secondary nucleation theory was applied to calculate the nucleation parameter (K_g) and the fold surface energy (σ_e), the value of which verify that the addition of β‐CD‐MAH‐La reduced the creation of new surface for β‐crystal and then led to faster crystallization rate. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Isothermal crystallization kinetics of anhydrous sodium acetate nucleated poly(ethylene terephthalate)

Studies on the isothermal crystallization kinetics of poly(ethylene terephthalate) (PET) nucleated with anhydrous sodium acetate were carried out. The nucleated agent had succeeded in promoting greater rates of crystallization in PET. A study of the melting behavior of the samples revealed that the nucleating agents promoted formation of thinner lamellae. The equilibrium melting temperature (T) of samples was determined using linear and nonlinear Hoffman Weeks procedure. The nonlinear Hoffman Week's procedure was found to be inapplicable in the current study. The Lauritzen‐Hoffman secondary nucleation theory was applied to determine the nucleation parameter (K_g), fold surface energy (σ_e), and work of chain folding (q). σ_e and q decreased on addition of nucleating agent. The approximate and exact form of the Lauritzen Z‐test was used to determine the operating regime. The operating regime was found to be primarily regime II for the range of temperatures studied. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Crystallization kinetics of bacterial poly(3‐hydroxylbutyrate) copolyesters with cyanuric acid as a nucleating agent

Effects of cyanuric acid (CA) on nonisothermal and isothermal crystallization, melting behavior, and spherulitic morphology of bacterial copolyesters of poly(3‐hydroxybutyrate), i.e., poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHBH), have been investigated. CA has excellent acceleration effectiveness on the melt crystallization of bacterial PHB, PHBV, and PHBH, better than the nucleating agents reported in the literatures, such as boron nitride, uracil, and orotic acid. PHBV and PHBH do not crystallize upon cooling from the melt at 10°C/min, while they are able to complete crystallization under the same conditions with an addition of 1% CA, with a presence of sharp crystallization exotherm at 75–95°C. Isothermal crystallization kinetics of neat and CA‐containing PHBV and PHBH were analyzed by Avrami model. Crystallization half‐times (t_1/2) of PHBV and PHBH decrease dramatically with an addition of CA. The melting behavior of isothermally melt‐crystallized PHBV and PHBH is almost not influenced by CA. Spherulitic numbers of PHBV and PHBH increase and the spherulite sizes reduce with an incorporation of CA. Nucleation densities of PHBV and PHBH increase by 3–4 orders of magnitude with a presence of 1% CA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effect of sepiolite on the crystallization behavior of biodegradable poly(lactic acid) as an efficient nucleating agent

To enhance the crystallization kinetics of poly(lactic acid) (PLA), fibrous sepiolite was explored for nucleating the crystallization of PLA. PLA/sepiolite nanocomposites were prepared via the melt‐extrusion method. The effect of sepiolite on the crystallization behavior, spherulite growth and crystal structure of PLA were investigated by means of differential scanning calorimetry (DSC), polarized optical microscope (POM), wide angle X‐ray diffraction (WAXD), Fourier transform infrared (FTIR), and scanning election microscope (SEM). On the basis of DSC and POM results, the overall crystallization kinetics of PLA/sepiolite nanocomposites were significantly enhanced leading to higher crystallinity and nucleation density, faster spherulite growth rate (G) and lower crystallization half‐time (t_1/2) compared with the neat PLA. Under non‐isothermal conditions, the PLA blend comprising 1.0 wt% of sepiolite still revealed two crystallization peaks upon cooling at a rate of 35°C/min. Above phenomena strongly suggested that sepiolite was an effective nucleating agent for PLA. FTIR and WAXD analyses confirmed that the crystal structure of PLA matrix was the most common α‐form. SEM micrographics illustrated the fine three‐dimensional spherulite structures with the lath‐shape lamellae regularly arranged in radial directions. POLYM. ENG. SCI., 55:1104–1112, 2015. © 2014 Society of Plastics Engineers     

Miscibility,thermal behaviour,morphology and mechanical properties of binary blends of poly[(R)‐3‐hydroxybutyrate] with poly(γ‐benzyl‐L‐glutamate)+

The miscibility, thermal behaviour, morphology and mechanical properties of poly[(R)‐3‐hydroxybutyrate] (PHB) with poly(γ‐benzyl‐L ‐glutamate) (PBLG) are investigated by means of differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and tensile tests. The DSC results show that PHB and PBLG are immiscible in the melt state. Such immiscibility also exists in the amorphous state due to a clear two‐phase separated structure observed by SEM measurements. The blend samples with different thermal history, namely as original and melt samples separately, display differences in thermal behaviour such as the DSC scan profile, the crystallinity and the melting temperature of PHB. The crystallization of PHB both from the molten state and the amorphous state is retarded on addition of the second component. The SEM measurements reveal that a phase inversion occurs between the PHB/PBLG (60/40) and PHB/PBLG (40/60) blends. Except for the PHB/PBLG (40/60) blend, a microphase separated structure is observed for all blend compositions. The mechanical properties vary considerably with blend composition. Compared with pure components, the PHB/PBLG (20/80) blend shows a certain improvement in mechanical properties. © 2001 Society of Chemical Industry     

Isothermal and nonisothermal crystallization kinetics of isotactic polypropylene nucleated with substituted aromatic heterocyclic phosphate salts

The crystallization kinetics of isotactic polypropylene (iPP) and nucleated iPP with substituted aromatic heterocyclic phosphate salts were investigated by means of a differential scanning calorimeter under isothermal and nonisothermal conditions. During isothermal crystallization, Avrami equation was used to describe the crystallization kinetics. Moreover, kinetics parameters such as the Avrami exponent n, crystallization rate constant Z_t, and crystallization half‐time t_1/2 were compared. The results showed that a remarkable decrease in t_1/2 as well as a significant increase in overall crystallization rate was observed in the presence of monovalent salts of substituted aromatic heterocyclic phosphate, while bivalent and trivalent salts have little effect on crystallization rate of iPP. The addition of monovalent metal salts could decrease the interfacial free energy per unit area perpendicular to PP chains σ_e value of iPP so that the nucleation rate of iPP was increased. During nonisothermal crystallization, Caze method was used to analyze the crystallization kinetics. It also showed that monovalent metal salts had better nucleation effects than bivalent and trivalent metal salts. From the obtained Avrami exponents of iPP and nucleated iPP it could be concluded that the addition of different nucleating agents changed the crystal growth pattern of iPP. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3307–3316, 2006     

Morphology and spherulitic growth kinetics in poly(ethylene oxide)/poly(n‐butyl methacrylate) blends

Results of a study concerning the morphology and the spherulite growth rates of poly(ethylene oxide) (PEO) in binary blends with poly(n‐butyl methacrylate) (PnBMA) are reported. Microscopic observations show that blending causes the spherulite structure to become coarser and less birefringent and confirms that the spherulitic growth rates of PEO were reduced by the addition of PnBMA. X‐ray diffraction studies show no change in the unit cell dimensions and a decrease in the degree of crystallinity upon blending. Analysis of the spherulite radial growth rate data by using Lauritzen–Hoffman theory indicates that crystallization in the range of 300 to 330 K occurs solely within regime III. The calculated surface free energy of folding, σ_e, for pure PEO is 57 erg cm^?2 and decreases with increasing the content of PnBMA in the blend. Copyright © 2004 Society of Chemical Industry