One-step preparation of poly(NIPAM-pyrrole) electroconductive composite hydrogel and its dielectric properties

Conductive polymers and hydrogels are two of the hot prospect polymer types that are used for new stimuli responsive materials. In this study, one-step preparation of electroconductive composite hydrogels containing polypyrrole (PPy) and N-isopropylacrylamide (NIPAM) using free radical polymerization technique was achieved with N,N-methylenebisacrylamide as a crosslinker and ammonium peroxy disulphate (APS) as initiator, in mixture of water/isopropyl alcohol. The equilibrium swelling degree of the poly(NIPAM)-pyrrole) electroconductive composite hydrogel was 9.88 g of H₂O/g dry polymer. According to TGA results, the thermal stability of the prepared composite poly(NIPAM-PPy) conductive hydrogel (700°C) hydrogel is higher than that of pure poly(NIPAM) hydrogel (600°C). Furthermore, prepared samples were characterized by FTIR, and SEM analyzes. Later, the samples were pressured into pellets so that electrical impedance spectroscopy (EIS) measurements were taken between 10 and 10 MHz at room temperature. The dielectric constant value of composite poly(NIPAM-PPy) hydrogel at 10 Hz is almost 10 times higher than that of poly(NIPAM) hydrogel. Both samples' real and imaginary parts of dielectric constant decreased with increased frequency. Samples exhibited non-Debye relaxation since experimental data fit into dielectric model of Havriliak-Negami. Moreover, low frequency data yielded d.c. conductivity of the pure and composite samples as 3.74 × 10⁻¹¹ and 1.02 × 10⁻⁸ S/cm, respectively. Real part of impedance at low frequencies also points out ~10³ times lower resistance values at 10 Hz for composite poly(NIPAM-PPy) hydrogel. Therefore, EIS results support that electroconductive composite hydrogel fabrication was achieved using free radical polymerization technique.     

Tribological and corrosion behaviors of fluorocarbon coating reinforced with sodium iron titanate platelets and whiskers

A series of sodium iron titanate (NFTO)–fluorocarbon composite coatings have been prepared with the liquid-phase blending method. The effects of two types of NFTO, NFTO platelets, and NFTO whiskers, on the tribological and corrosion behaviors of the composite coatings, are systematically studied. The results show that the addition of NFTO can significantly enhance the friction-reducing and wear resistance performances of the fluorocarbon coating. Under dry sliding, the minimum specific wear rate is 1.67 × 10⁻⁴ mm³/Nm for the platelet-filled composite coatings and 1.15 × 10⁻⁴ mm³/Nm for the whisker-filled composite coatings, respectively, showing a decrease of 83.5 and 88.6% than that of pure coating. Under a simulated seawater environment, the minimum specific wear rate is 5.44 × 10⁻⁵ mm³/Nm for the platelet-filled composite coatings and 0.84 × 10⁻⁵ mm³/Nm for the whisker-filled composite coatings, respectively, showing a decrease of 90.5 and 98.5% than that of pure coating. The morphologies of worn surfaces, wear debris, and transfer films are analyzed, and the corresponding wear resistance mechanisms are discussed. The electrochemical impedance spectroscopy certifies a remarkably improved corrosion resistance of the composite coatings which have been immersed in 3.5 wt % NaCl solution for 30 days. The composite coating reinforced with 7.5 wt % platelets shows the highest resistance of 256.3 × 10⁶ Ω·cm², approximately two orders of magnitude higher than that of pure coating. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48936.     

Improvement of microwave absorption for PAni/HA/TiO2/Fe3O4 nanocomposite after chemical treatment

In order to obtain efficient microwave absorbers that possess high conductivity, dielectric and magnetic properties, hexanoic acid doped polyaniline (PAni) nanocomposites which contain different ratios of ferum (II) oxide (Fe₃O₄) and titanium dioxide (TiO₂) nanoparticles were successfully prepared by in situ chemical polymerization through template free method. Chemical structure, conductivity, morphology, thermal stability, magnetic properties, and amorphous/crystalline behavior of PAni nanocomposites were characterized by Fourier transform infrared spectrometer (FTIR), four point probe, field emission scanning electron microscope (FESEM), thermal gravimetric analysis (TGA), vibrating samples magnetometer (VSM), and X‐ray diffractometer (XRD), respectively. From this study, conductivity was significantly improved from 8.48 × 10⁻⁴−1.23 × 10⁻² S/cm for PAni nanocomposites without any chemical treatment (during addition of Fe₃O₄) to 3.58 × 10⁻²−4.77 × 10⁻² S/cm for those with chemical treatment. PAni nanocomposites with chemical treatment show a narrow sharp reflection loss (RL) peak with high absorption (−48.9 dB) at lower frequency due to the limited individual Fe₃O₄ nanoparticles outside the nanorods/nanotubes as proved by the new proposed mechanism (Fig. 5 ), while it shows a broad RL peak with poor absorption (−13 dB) at higher frequency for those without chemical treatment. The novelty of this research has been focused on PAni with chemical treatment which yield better microwave absorption property (99.999% absorption), combination of high conductivity (3.58 × 10⁻²−4.77 × 10⁻² S/cm), high heterogeneity and moderate magnetization (Ms = 8.87–28.49 emu/g) compare to the PAni without chemical treatment. POLYM. COMPOS., 34:1186–1194, 2013. © 2013 Society of Plastics Engineers     

Preparation of a novel synergistic flame retardant and its application in silicone rubber composites

Dehydration condensation product (DHCP) was prepared by addition and dehydration condensation reactions of 9,10-dihydro-9-oxa-10-phenanthrene-10-oxide (DOPO), vinyl trimethoxysilane, and (3-aminopropyl) triethoxysilane. DHCP-PA with high phosphorus content was prepared by reaction between DHCP and phytic acid (PA). It was then compounded with oxidized multi-walled carbon nanotubes (OMWCNTs) to prepare silicone rubber (SR) flame retardant composites. The results showed that the SR with a small amount of DHCP-PA owned good flame retardant effect. The heat release rate (HRR) was decreased from 436 kW/m² for pure SR to 288 kW/m² for the SR with 5 phr DHCP-PA, and the decreasing degree was 33.9%. After mixing 5 phr DHCP-PA with 1 phr OMWCNTs, the HRR of SR composite was decreased from 436 to 251 kW/m², the smoke production rate was decreased from 0.161 to 0.087 m²/s, the limited oxygen index value was increased from 20.4% to 28.4%, and the flame retardant grade can reach UL94 V-0. In addition, the synergistic flame retardant mechanism was researched and analyzed.     

Behaviors of polyelectrolyte AAm/AMPS/bentonite composite hydrogels in uptake of uranyl ions from aqueous solutions

Uranyl ion (UO₂²⁺) sorption properties of polyelectrolyte composite hydrogels made by the polymerization of acrylamide (AAm) with 2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid (AMPS) and clay such as bentonite (Bent) were investigated as a function of composition to find materials with swelling and uranyl ion sorption properties. Highly swollen AAm/AMPS hydrogels and AAm/AMPS/Bent composite hydrogels were prepared by free radical solution polymerization in aqueous solutions of AAm with AMPS as co‐monomer and two multifunctional crosslinkers such as ethylene glycol dimethacrylate (EGDMA) and 1,4 butanediol dimethacrylate (BDMA). Swelling experiments were performed in water at 25°C, gravimetrically. The influence of AMPS content in hydrogels was examined. Uranyl ion adsorption from aqueous solutions was studied by batch sorption technique at 25°C. The effect of uranyl ion concentration and mass of AMPS on the uranyl ion adsorption were examined. Finally, adsorption capacity (the amount of sorbed uranyl ion per gram of dry hydrogel) (q) was calculated to be 0.67 × 10⁻³–2.11 × 10⁻³ mol uranyl ion per gram for the hydrogels. Removal effiency of uranyl ions (RE%) was changed range 9.05–29.92%. The values of partition ratio (K_d) of uranyl ions was calculated to be 0.10–0.43 for AAm/AMPS hydrogels and AAm/AMPS/Bent composite hydrogels, respectively. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Amphiphilic chitosan/acrylic acid/thiourea based semi-interpenetrating hydrogel: Solvothermal synthesis and evaluation for controlled release of organophosphate pesticide,triazophos

The current study reports the solvothermal synthesis of amphiphilic chitosan-based semi-interpenetrating (CAT-SIPH) hydrogel for controlled release of an organophosphate pesticide, triazophos. CAT-SIPH is prepared from natural backbone polymer chitosan (CS) and monomer, acrylic acid (AA) employing initiator (K₂S₂O₈), and cross-linker, thiourea (CSN₂H₄) using solvothermal technique under 7 Psi pressure in an autoclave. The polymerization reaction variables like reaction time, the volume of solvent, concentration of initiator, cross-linker, and monomer are optimized to get the best product yield in terms of percentage grafting. The optimized conditions for solvothermal polymerization reaction carried out for 60 min are solvent volume (10 ml), concentrations of acrylic acid (0.2 mol/L), K₂S₂O₈ (0.45 × 10⁻²mol/L) and thiourea (1.75 × 10⁻⁴ mol/L). The swelling behavior of CAT-SIPH hydrogel synthesized under optimized conditions is studied in the terms of swelling ratio. CAT-SIPH is characterized by Fourier transform infrared spectra (FT-IR), ^IHNMR, thermal analysis (TA), Zeta potential, and scanning electron microscopy (SEM). The potential of cross-linked hydrogel CAT-SIPH for controlled release of an organophosphate pesticide, Triazophos on to sandy loam soil is assessed. The experimental investigations proved that synthesized hydrogel can be effectively employed as a pesticide carrier for controlled release on to loamy soil as the maximum release (53%) is observed even after 25 days at pH 6 and value get lowered under acidic and basic conditions. The present investigation demonstrated the potential of chitosan-based CAT-SIPH hydrogel as a pH-responsive release vehicle for agrochemicals onto the soil matrix and offers a potential solution for the prevention of surface and groundwater contamination.     

Nafion® reinforced with polyacrylonitrile/ZrO2 nanofibers for direct methanol fuel cell application

Nafion® membrane blended with polyacrylonitrile nanofibers decorated with ZrO₂ was successfully fabricated. The composite membrane showed improved proton conductivity, swelling ratio, thermal and mechanical stability, reduced methanol crossover, and enhanced fuel cell efficiency. The nanocomposite membranes achieved a reduced methanol crossover of 5.465 × 10⁻⁸ cm² S⁻¹ compared to 9.118 × 10⁻⁷ cm² S⁻¹ of recast Nafion® membrane using a 5 M methanol solution at 80°C. The composite membrane also showed an ion conductivity of 1.84 compared to 0.25 S cm⁻¹ recast Nafion® at 25°C. The composite membranes showed a peak power density of 68.7 mW·cm⁻² at 25°C, these results show a promising composite membrane for fuel cell application.     

Sulfonated poly(ether ether ketone)/s–TiO2 composite membrane for a vanadium redox flow battery

The SPEEK/s-TiO₂ composite membrane was prepared by blending sulfonated poly(ether ether ketone) (SPEEK) and sulfonated titanium dioxide (s-TiO₂) nanoparticles. The important physiochemical parameters such as proton conductivity, water uptake, swelling degree and ion exchange capacity of the composite membrane were measured. The thermal stability and chemical stability were also tested. It was observed that the SPEEK/s-TiO₂ composite membrane exhibited the best selectivity (7.13 × 10⁴ S·min·cm⁻³) accompanying high proton conductivity (0.061 S·cm⁻¹) and low tetravalent vanadium ion (VO²⁺) permeability (8.55 × 10⁻⁷ cm²·min⁻¹) compared with Nafion117, SPEEK and SPEEK/TiO₂ membranes. The battery performance with these membranes was characterized by charge–discharge cycling tests and it was found that the SPEEK/s-TiO₂ composite membrane showed the highest energy efficiency (EE) up to 82.3%, indicating the SPEEK/s-TiO₂ composite membrane is a candidate for vanadium redox flow battery (VRFB) application. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48830.     

Preparation of cellulose-based conductive hydrogels with ionic liquid

Conductive hydrogel composed of microcrystalline cellulose (MCC) and polypyrrole (PPy) was prepared in ionic liquid; and the resulting hydrogel was characterized with FT-IR, SEM, XRD and TGA. By doping with TsONa, the MCC/PPy composite hydrogels showed relatively high electrical conductivity, up to 7.83 × 10⁻³ S/cm, measured using a four-probe method. The swelling kinetics of the composite hydrogels indicated that the swelling process was mainly influenced by the cellulose content; and the equilibrium swelling ratio decreased as the increasing of MCC content in the hydrogels. In addition, the MCC/PPy composite hydrogels exhibited significantly enhanced mechanical property in contrast to MCC hydrogel.     

Novel organic–inorganic composite material as a cation exchanger from a triterpenoidal system of dammar gum: synthesis,characterization and application

A pioneer study has been conducted to synthesize novel hydrogel starting from a non-cellulosic raw material, gum dammar-a triterpenoidal system, and then converting this hydrogel into an organic–inorganic composite zirconium-based ion exchanger. Gum dammar was cross-linked with polyacrylamide zirconium (IV) iodo-oxalate [Gd-cl-poly(AAm)-Zr (IV) iodo-oxalate] by incorporating inorganic precipitates into the polymeric mixture. The polymeric mixture was synthesized using gum dammar (Gd), acrylamide (AAm), N, N′-methylene-bis-acrylamide (MBA) and potassium persulphate (KPS). The reaction conditions for synthesis of hydrogel and ion exchanger such as time (120 min), temperature (70 °C), solvent (4 mL), concentration of monomer (12.97 × 10^?3 mol/L), initiator (1.48 × 10^?4 mol/L), cross-linker (4.22 × 10^?4 mol/L) and ratio of zirconium oxychloride (0.1 M), potassium iodate (0.1 M) and oxalic acid (0.1 M) in ratio 2:3:2 were optimized to obtain maximum ion exchange capacity (2.02 meq/g). The morphology and structure of hydrogel and ion exchanger were studied using FTIR, SEM, XRD and TGA/DTA/DTG. The SEM study was followed by energy dispersive spectroscopy for elemental analysis. The ion exchanger was quite stable in various acids and bases at low concentration but it completely dissolved in acids and bases at high concentrations. Distribution studies showed that the synthesized ion exchanger had high selectivity for Pb²⁺ ions. Thus, the polymeric-inorganic hybrid material showed integration of both inorganic and organic characteristics within the composite material.     

Conductive polymers/polyacrylonitrile composite fibers: Fabrication and properties

Polypyrrole/polyacrylonitrile, polyaniline/polyacrylonitrile, and poly(3,4‐ethylenedioxythiophene)/polyacrylonitrile composite fibres were fabricated successfully by in situ polymerization. The morphologic observations confirmed the uniformly‐covered polyacrylonitrile fiber surface by conductive conjugated polymers. These composite fibers exhibited conductivity in the range of 1.4 × 10⁻² to 5.2 × 10⁻¹ S cm⁻¹. Improved thermal stability of the composite fibers was observed from thermogravimetric analysis results. Structural analysis indicated that the interactions of both hydrogen‐bonding and the electrostatic attraction existed between polyacrylonitrile chains and conjugated polymers. These novel composite fibers still possessed original fibrillar morphology and strength properties and showed a good stability to atmosphere and washing. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

The β‐δ‐Phase Transition and Thermal Expansion of Octahydro‐1,3,5,7‐Tetranitro‐1,3,5,7‐Tetrazocine

Phase behavior of octahydro‐1,3,5,7‐tetranitro‐1,3,5,7‐tetrazocine (HMX) is investigated by X‐ray powder diffraction (XRD). The XRD patterns at elevated temperature show that there is a co‐existing temperature range of β‐ and δ‐phase during the phase transition process. Additionally, mechanical forces can catalyze the conversion from δ‐ back to β‐phase. Based on the diffraction patterns of β‐ and δ‐phase at different temperatures, we calculate the coefficients of thermal expansion by Rietveld refinement. For β‐HMX, the linear coefficients of thermal expansion of a‐axis and b‐axis are about 1.37×10⁻⁵ and 1.25×10⁻⁴ °C⁻¹. A slight decrease in c‐axis with temperature is also observed, and the value is about −0.63×10⁻⁵ °C⁻¹. The volume coefficient of thermal expansion is about 1.60×10⁻⁴ °C⁻¹, with a 2.2% change from 30 to 170 °C. For δ‐HMX, the linear coefficients of thermal expansion of a‐axis and c‐axis are found to be 5.39×10⁻⁵ and 2.38×10⁻⁵ °C⁻¹, respectively. The volume coefficient of thermal expansion is about 1.33×10⁻⁴ °C⁻¹, with a 2.6% change from 30 to 230 °C. The results indicate that β‐HMX has a similar volume coefficient of thermal expansion compared with δ‐HMX, and there is about 10.5% expansion from β‐HMX at 30 °C to δ‐HMX at 230 °C, of which about 7% may be attributed to the reconstructive transition.     

High pyroelectric performance in Pb0.99Nb0.02[(Zr0.57Sn0.43)0.94Ti0.06]0.98O3/Al2O3 composites by design

High pyroelectric performance around human body temperature is essential for ultra-sensitive infrared detectors of medical systems. Herein, toward human health monitoring, composite ceramics (1-x)Pb_0.99Nb_0.02[(Zr_0.57Sn_0.43)_0.94Ti_0.06]_0.98O₃/xAl₂O₃ (x = 0, 0.1, and 0.2) were designed. A metastable ferroelectric (FE) phase was induced in the anti-FE matrix by the Al₂O₃ component-induced internal stress, and in turn FE-anti-FE phase boundary was constructed. The ceramics at x = 0.2 exhibit high pyroelectric coefficient with p = 10.9 × 10⁻⁴ C·m⁻²·K⁻¹ and figures of merit with current responsivity F_i = 6.23 × 10⁻¹⁰ m·V⁻¹, voltage responsivity F_v = 12.71 × 10⁻² m²·C⁻¹, and detectivity F_d = 7.03 × 10⁻⁵ Pa^−1/2 around human body temperature. Moreover, the enhanced pyroelectric coefficients exist in a broad operation temperature range with a large full width at half maximums of 18.5°C and peak value of 29.2 × 10⁻⁴ C·m⁻²·K⁻¹ at 48.2°C. The designed composite ceramic is a promising candidate for infrared thermal imaging technology of noncontact human health monitoring system.     

Synthesis of α‐cellulose/polypyrrole composite for the removal of reactive red dye from aqueous solution: Kinetics and equilibrium modeling

In this work, a composite from α‐cellulose coated with conducting polypyrrole by in situ polymerization using potassium persulfate as oxidant was obtained. The composite was characterized by fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry, UV/Vis spectroscopy, and scanning electron microscopy (SEM) analysis showed homogeneous coating of α‐cellulose with polypyrrole (PPy) to produce a composite with a conductivity of 3.5 × 10⁻⁵ S/m. Batch aqueous adsorption experiments of the reactive red 120 (RR120) dye onto the synthesized material were conducted. The results showed that this composite is an efficient adsorbent for RR120 dye removal. For the adsorption experiments set to an initial pH of 3.9, the adsorption capacity was 15.6 mg of dye/g of composite for an equilibrium concentration (in the liquid) of RR120 dye equal to 1,000 mg/L, whereas a value of 96.1 mg of dye/g of composite was obtained when the solution pH was set to 2.0 for the same equilibrium concentration. When performing adsorption experiments using pure α‐cellulose, dye adsorption was insignificant at any pH value. Adsorption isotherm for RR120 was described by a typical Freundlich model. The transient adsorption of RR120 on the synthesized composite was described by a general three‐resistance model that includes the transport on the film that surrounds the composite particles, diffusion inside the particles, and adsorption on the surface of the particles. A fitting of the uptake curves was performed allowing the estimation of values for the effective diffusivity, D₀, and the adsorption rate coefficient, k₁. For the adsorption experiments with an initial pH value set to 3.9, D₀ was estimated as 1.05 × 10⁻¹⁰ m²/s, whereas k₁ was 1.65 × 10⁻⁴ Lⁿ/g mg^{n − 1} s; the corresponding values of k₁ at pH = 2 and 9.0 were 3.18 × 10⁻⁴ and 5.16 × 10⁻⁵, respectively. POLYM. COMPOS., 36:312–321, 2015. © 2014 Society of Plastics Engineers     

Facile preparation and characterization of sodium alginate/graphite conductive composite hydrogel

Conductive composite hydrogels based on sodium alginate (SA) and graphite were fabricated by a facile method via dispersing homogeneously conductive graphite into SA hydrogel matrix. The hydrogel was formed by in situ release of Ca²⁺ from Ca–EDTA, thus eliminating the multistep reactions and tedious purification compared to the previous work. Raman spectra, scanning electron microscopy (SEM), X‐ray diffraction (XRD), and thermogravimetric analysis (TGA) were used to characterize the structure, crystalline nature, and thermostability of SA/graphite composite hydrogels. The SA/graphite composite hydrogels exhibited the improved network and layer‐type structure. The thermal stability of the hydrogel decreased slightly after the graphite was incorporated into the SA hydrogel matrix regardless of the content of graphite. The enhanced mechanical strength of SA/graphite composite hydrogel was achieved via increasing the f value (i.e., [Ca²⁺]/[COO^‐ in alginate]) and lowering graphite content. The conductivity of the composite hydrogels could be varied in a broad range, reaching up to 10⁻³ S/cm, mainly depending on the content of graphite and the f value. POLYM. COMPOS., 37:3050–3056, 2016. © 2015 Society of Plastics Engineers     

Superhydrophobic-superoleophilic heptafluorodecyl triethoxysilane/graphitic carbon spheres Co-modified porous monolith for water/oil separation

Water/oil separation has been a flourishing research focus due to severe oil-spill accidents. The current work reports on preparation, characterization and water/oil separation performance of heptafluorodecyl triethoxysilane (FAS) and graphitic carbon spheres (GCS) co-modified mullite porous ceramic (FAS/GCS-MC) with superhydrophobic and superoleophilic characters. The water contact angle of FAS/GCS-MC was determined as about 161°. The continuous water/oil separation rates for paraffin, vegetable and vacuum pump oils were 3.4 × 10⁴ g m⁻² min⁻¹, 2.2 × 10⁴ g m⁻² min⁻¹ and 1.3 × 10⁴ g m⁻² min⁻¹, respectively; even after 10 cycles, the separation rates remained almost unchanged in high selectivity (above 95%). The as-prepared FAS/GCS-MC was resistant to the temperature change and acid/base erosion, and showed stable superhydrophobicity and separation efficiency. In addition, the separation rate after applied a voltage to FAS/GCS-MC could be obviously enhanced by a self-heating process.     

Chitosan‐based gel film electrolytes containing ionic liquid and lithium salt for energy storage applications

Fabrication, characterization, and a comparative study have been performed for chitosan‐based polymer electrolytes using two different dispersion media. Chitosan gel film (solid) electrolytes are fabricated using acetic acid or adipic acid as the dispersant for chitosan in combination with ionic liquid and lithium salt. This quaternary system of chitosan, acetic acid or adipic acid, 1‐butyl‐3‐methylimadazolium tetrafluoroborate (ionic liquid), and lithium chloride is formed as an electrolyte for potential secondary energy storage applications. The ionic conductivities, thermal, structural, and morphological properties for these electrolytes are compared. The ionic conductivities for chitosan/adipic acid (CHAD) and for chitosan/acetic acid (CHAC) systems are in the range of 3.71 × 10⁻⁴−4.6 × 10⁻³ and 1.3 × 10⁻⁴ −3.2 × 10⁻³ S cm⁻¹, respectively. The thermal stability of CHAD‐based electrolytes is determined to be higher than that of CHAC‐based electrolytes. Preliminary studies are performed to determine the electrochemical stability of these materials as solid film electrolytes for electrochemical supercapacitors. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42143.     

Electrical properties of FeII‐terpyridine‐Modified cellulose nanocrystals and polycaprolactone/FeII‐CTP nanocomposites

Supramolecular crosslinked Fe^II‐terpyridine cellulose nanocrystals (Fe‐CTP) were prepared by surface modification of cellulose nanocrystals with 4′‐chloro‐2,2′:6′,2″‐terpyridine and subsequent reaction with Fe(II)SO₄. The prepared complex was characterized using transmission electron microscopy (TEM), ultraviolet spectroscopy (UV), thermogravimetric analysis (TGA), and measuring its electrical properties at temperatures from 25 to 70°C. Use of Fe‐CTP at loadings from 1% to 10% (wt. ratio) in nanocomposites with polycaprolactone polymer was investigated; the nanocomposites were characterized regarding their electrical properties, which studied using broadband AC‐relaxation spectroscopy in the frequency range between 0.1 Hz and 1 MHz. The results were compared to that of PCL nanocomposites containing multiwalled carbon nanotubes (CNT). Variation in real and imaginary parts of permittivity has been explained on the basis of interfacial polarization of fillers in the polymer medium. The percolation limit of the conductive CNT and Fe‐CTP as studied by ac conductivity measurements has also been reported. Fe‐CTP showed conductivity values in the range of semiconductors. PCL/Fe‐CTP nanocomposites showed conductivity values from 1.98 × 10⁻¹¹ to 3.76 × 10⁻⁶ while PCL/CNT nanocomposites showed conductivity values from 1.4 × 10⁻¹⁰ to 3.67 × 10⁻⁴ S/m for 1–10 wt% CNT content. POLYM. COMPOS., 37:2734–2743, 2016. © 2015 Society of Plastics Engineers     

A redox poly(ionic liquid) hydrogel: Facile method of synthesis and electrochemical sensing

In this article, a redox-responsive poly(ionic liquid) (redox-PIL) hydrogel Poly(1-vinyl-3-propionate imidazole phenothiazine sulfonic acid)-chitosan [Poly(VPI⁺PTZ-(CH₂)₃SO₃⁻)-CS] was produced by using chitosan (CS) crosslinking with redox-PIL Poly(1-vinyl-3-propionate imidazole phenothiazine sulfonic acid [Poly(VPI⁺PTZ-(CH₂)₃SO₃⁻)]. The incorporation of redox-active counter anions 3-(phenothiazine-10-yl) propane 1-sulfonic acid anions (PTZ-(CH₂)₃SO₃⁻) into cationic PIL-polyimidazole rendered Poly(VPI⁺PTZ-(CH₂)₃SO₃⁻) with electron catalytic ability, ionic conductivity, and electron conductivity. Poly(VPI⁺PTZ-(CH₂)₃SO₃⁻)-CS combines the properties of hydrogel and redox-PIL, thus offering intrinsic porous conducting frameworks and promoting the transport of charges, ions, and molecules, leading hydrogel with excellent electrochemical properties. The crosslinking occurrence of Poly(VPI⁺PTZ-(CH₂)₃SO₃⁻) and CS resulting from the synthetic process of hydrogel was verified by differential scanning calorimetry and thermogravimetric analysis. A three-dimensional polymer network hydrogel with good biocompatibility and permeability was formed after crosslinking. In addition, only 64% weight loss within 600 °C was observed in Poly(VPI⁺PTZ-(CH₂)₃SO₃⁻)-CS representing its thermally stable performance. When used as an electrochemical sensor, the hydrogel-modified gold electrode improved the electrocatalytic oxidation of cysteine. Differential pulse voltammetry results indicated that the detection range was from 5 × 10⁻⁸ to 5 × 10⁻³ M and the limit of detection was 6.64 × 10⁻⁸ M. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48051.     

MnO anchored reduced graphene oxide nanocomposite for high energy applications of Li-ion batteries: The insight of charge-discharge process

In the present work, a new class of anode material for high energy applications of Li-ion battery is prepared by easy and large-scale producible process. Herein, the nanocomposite of MnO and reduced graphene oxide (rGO) is prepared by anchoring MnO nanoparticles into 3D matrix of rGO hydrogel followed by annealing process. The composite which has homogeneous distribution of MnO particles on conducting rGO layers demonstrated superior electrochemical performance such as high reversible capacity, stable cycle life and better rate capability. It has shown initial discharge capacity of 2358 mAh g⁻¹ and retained 570 mAh g⁻¹ after 100 cycles as compared to pristine MnO which shown initial discharge capacity of 820 mAh g⁻¹ and retained only 45 mAh g⁻¹ after 100 cycles. The retained capacity of new MnO/rGO anode is much higher than the theoretical capacity of conventional graphite anode. Moreover, the MnO/rGO nanocomposite shows six times higher Li⁺ ion diffusion of 4.18 × 10⁻¹² cm² s⁻¹ as compared to 6.84 × 10⁻¹³ cm² s⁻¹ of MnO. In addition, the study provides insight of charge-discharge process, which conducted in initial, discharge and charge states of pristine MnO and MnO/rGO composite using ex-situ X-ray diffraction and X-ray photon spectroscopy techniques.