Preparation and characterization of poly (vinyl butyral)‐leather fiber composites

This study reports the preparation and characterization of composites with recycled poly (vinyl butyral) (PVB) and wet blue leather fiber with leather contents of 30, 50, and 70 wt%, using an extruder equipped with a Maillefer single screw operated with a flat extrusion die. The components of the composites were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and Fourier transform infrared spectroscopy (FTIR). After extrusion, the PVB/leather composite plates were compression‐molded to obtain specimens for testing the tensile properties, hardness, abrasion resistance, and tear strength. The morphologies of the composites were analyzed by scanning electron microscopy (SEM). The DMA and FTIR analyses showed that the recycled PVB contained plasticizer remained in the polymer matrix after extrusion. The SEM analysis revealed good interfacial adhesion between the PVB matrix and the leather fibers. Increasing the leather content in the composites led to a significant increase in the tensile modulus and a reduction in the tensile strain at breaks. The Shore hardness of the composites increased with the wt% of leather, whereas the abrasion resistance decreased. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers.     

PVDF/PMMA/Basalt fiber composites: Morphology,melting and crystallization,structure, mechanical properties,and heat resistance

This paper is to study the effect of basalt fiber on morphology, melting and crystallization, structure, mechanical properties, melting and crystallization of PVDF/PMMA composites using scanning electron microscopy (SEM), X‐ray, differential scanning calorimeter (DSC), dynamical mechanical analysis (DMA), etc. Basalt fiber may disperse well in PVDF/PMMA matrix and form compact fiber network, and this makes tensile and flexural strength of fiber reinforced PVDF/PMMA composites get to the maximum value of 62 and 102 MPa, respectively. However, the mechanical properties begin to decrease when basalt fiber content exceeds 20 wt %. The α and β phase of PVDF can coexist in composites, and basalt fiber and PMMA can induce β phase of PVDF. The melting temperature of PVDF in composites is kept unchanged, but the degree of crystallinity of composites increases as basalt fiber content increase, and then declines when fiber content exceeds 20%. The DSC results confirm that the nucleation ability of PVDF is enhanced by basalt fiber. Also, the heat resistance of PVDF/PMMA composite is improved from 133 to 146.1°C due to basalt fiber. The DMA shows that basalt fiber increases the storage modulus of PVDF/PMMA composite, and the loss peak of PMMA increases from 116.1 to 130°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40494.     

Preparation and characterization of multi‐walled carbon nanotube/poly(ethylene terephthalate) nanoweb

Multi‐walled carbon nanotube (MWCNT)/Poly(ethylene terephthalate) (PET) nanowebs were obtained by electrospinning. For uniform dispersion of MWCNTs in PET solution, MWCNTs were functionalized by acid treatment. Introduction of carboxyl groups onto the surface of MWCNTs was examined by Fourier transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD) analysis. MWCNTs were added into 22 wt % PET solution in the ratio of 1, 2, 3 wt % to PET. The morphology of MWCNT/PET nanoweb was observed using field emission‐scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM). The nanofiber diameter decreased with increasing MWCNT concentration. The distribution of the nanofiber diameters showed a bi‐modal shape when MWCNTs were added. Thermal and tensile properties of electrospun MWCNT/PET nanowebs were examined using a differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA) and etc. Tensile strength, tensile modulus, thermal stability, and the degree of crystallinity increased with increasing MWCNT concentration. In contrast, elongation at break and cold crystallization temperature showed a contrary tendency. Electric conductivities of the MWCNT/PET nanowebs were in the electrostatic dissipation range. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal behavior and surface morphology studies on polystyrene grafted sago starch

Polystyrene grafting onto sago starch was carried out by using ceric ammonium nitrate as a redox initiator. The grafted copolymers were characterized by FTIR, thermogravimetry (TGA), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). FTIR spectra analysis of the grafted chain and commercial polystyrene was identical, indicating that styrene was successfully grafted onto sago starch. TGA thermograms and analysis of DSC curves showed that the thermal stability of starch increases as a result of grafting. SEM micrographs showed the deformed prolate ellipsoidal shape of sago starch particles and this shape disappeared in polystyrene grafted sago starch being replaced with a spongy surface with pores. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2053–2058, 2003     

Facile fabrication of PVA composite fibers with high fraction of multiwalled carbon nanotubes by gel spinning

Poly(vinyl alcohol) (PVA) composite fibers with high fraction of multiwalled carbon nanotubes (MWCNTs) were prepared by gel spinning process. Here, a modified process was introduced to prepare concentrated PVA/MWCNTs/DMSO spinning dope, and to attain good dispersion of MWCNTs in the fibers. The final composite fibers were studied by thermogravimetric analyzer (TGA), Fourier transform infrared spectrometer (FTIR), Raman spectroscopy, differential scanning calorimetry (DSC), and WAXD analysis. The total content of MWCNTs in PVA composite fibers, from 5 to 30 wt%, was confirmed by TGA analysis. FTIR and Raman measurements demonstrated the existence of strong hydrogen interaction between MWCNTs and PVA matrix. SEM images of composite fibers showed smooth surface, regular cross‐section shape and good dispersion of MWCNTs in the fibers. DSC analysis showed that the crystallinity first increased and then decreased with the increase of MWCNTs contents. It can be concluded that low concentration of MWNCTs can act as nucleation sites for crystallization of PVA component, and large amount of MWCNTs may impede the crystallization of PVA component. The WAXD analysis results indicated that the crystal orientation of the PVA component in PVA composite fibers is almost identical at the same drawn ratio. Polarized Raman analysis indicated a small increase in MWCNTs orientation for the composite fibers. The mechanical properties tests showed that the composite fibers exhibit significant improvement in tensile strength and modulus as compared to the neat PVA fibers. The composite fibers also showed sustained growth in electrical conductivity. POLYM. ENG. SCI., 58:37–45, 2018. © 2017 Society of Plastics Engineers     

Films of PLLA/PHBV: Thermal,morphological, and mechanical characterization

Blends of poly(L ‐lactic acid)/poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PLLA/PHBV), both semicrystalline polymers, were prepared in different compositions (100/0, 80/20, 60/40, 50/50, 40/60, 20/80, and 0/100) and characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), polarized light microscopy (PLM), and tensile tests. Although PLLA/PHBV blends do not present clear phase separation by SEM, the analyses by TGA, DSC, and DMA showed that the PLLA/PHBV blends are immiscible. The cross sections observed by SEM showed that the morphology of the blends changes from porous to dense, due to the composition. DSC and DMA data showed two distinct glass transition and melting temperatures. However, the DMA analysis related to frequency variation showed partial molecular interactions between PHBV and PLLA. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2898–2906, 2002     

Mechanical,Thermal and Morphological Characterization of High-Density Polyethylene and Vermiculate Composites

High-density polyethylene composites containing 7, 10, 15 and 20% w/w vermiculite (VMT) were prepared by extrusion in a twin-screw extruder at various shear rates. The thermal and mechanical properties and morphological characteristics of the composites were evaluated and compared with pure high-density polyethylene. The blend morphologies were determined by scanning electron microscopy (SEM). The thermal properties of the composites were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The TGA results reveal that the use of VMT particles to fill polyethylene increased the thermal stability of the composite. The results obtained indicate that a shear speed of 400 rpm and vermiculite content of 7% showed the best properties of impact resistance. These observations were confirmed by morphology analysis.     

Mechanical,thermal properties,and flame retardancy of PC/ultrafine octaphenyl‐POSS composites

Composites of ultrafine polyhedral oligomeric octaphenyl silsesquioxane (OPS) and polycarbonate (PC) were prepared by melt blending. The mechanical and thermal properties of the composites were characterized by tensile and flexural tests, impact test, differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), and thermal gravimetric analysis (TGA). Rheological properties of these melts were tested by torque rheometer. The flame retardancy of the composites was tested by limiting oxygen index (LOI), the vertical burning (UL‐94), and cone calorimeter test. The char residue was characterized by scanning electron microscope (SEM) and ATR‐FTIR spectrum. Furthermore, the dispersion of OPS particles in the PC matrix was evidenced by SEM. The results indicate that the glass transition temperatures (T_g) and torque of the composites decrease with increasing OPS loading. The onset decomposition temperatures of composites are lower than that of PC. The LOI value and UL‐94 rating of the PC/OPS composites increase with increasing loading of OPS. When OPS loading reaches 6 wt %, the LOI value is 33.8%, UL‐94 (1.6 mm) V‐0 rating is obtained, and peak heat release rate (PHRR) decreases from 570 to 292 kJ m^?2. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Crystal transformation and thermomechanical properties of poly(vinylidene fluoride)/clay nanocomposites

The crystal transformation and thermomechanical properties of melt‐intercalated poly(vinylidene fluoride) (PVDF)/clay nanocomposites are reported in this study. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were used to study the thermal properties of PVDF and its nanocomposites with various clay concentrations. The incorporation of clay in PVDF results in the formation of β‐form crystals of PVDF. DSC study of melting behavior suggested the presence of only α‐phase crystals in neat PVDF and both α‐ and β‐phase crystals in the nanocomposite. This conclusion was corroborated by findings from Fourier‐transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD). Dynamic mechanical analysis (DMA) indicated significant improvements in storage modulus over a temperature range of 20–150 °C. The coefficient of thermal expansion (CTE) decreases with increasing clay loading. Copyright © 2004 Society of Chemical Industry     

Surface modification of MWCNT and its influence on properties of paraffin/MWCNT nanocomposites as phase change material

Multiwalled carbon nanotubes (MWCNTs) were modified by an organo-silane in order to improve their dispersion state and stability in paraffin wax. A family of paraffin-based phase change material (PCM) composites filled with MWCNTs was prepared with different loadings (0, 0.1, 0.5, and 1 wt%) of pristine MWCNTs and organo-silane modified MWCNTs (Si-MWCNT). Structural analyses were performed by means of Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and rheological studies using temperature sweeps. Moreover, phase change transition temperatures and heat of fusion as well as thermal and electrical conductivities of the developed PCM nanocomposites were determined. The SEM micrographs and FTIR absorption bands appearing at approximately 1038 and 1112 cm⁻¹ confirmed the silane modification. Differential scanning calorimetery (DSC) results indicate that the presence of Si-MWCNTs leads to slightly favorable enhancement in the energy storage capacity at the maximum loading. It was also shown that the thermal conductivity of the PCM nanocomposites, in both solid and liquid phases, increased with increasing the MWCNT content independent of the kind of MWCNTs by up to about 30% at the maximum loading of MWCNTs. In addition, the modification of MWCNTs made the samples completely electrically nonconductive, and the electrical surface resistivity of the PCMs containing pristine MWCNTs decreased with increasing MWCNTs loading. Furthermore, the rheological assessment under consecutive cyclic phase change demonstrated that the samples containing modified MWCNTs are more stable compared to the PCM containing pristine MWCNTs. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48428.     

Improving thermal conductivity and shear strength of carbon nanotubes/epoxy composites via thiol‐ene click reaction

This study investigates the effect of the thiol‐ene click reaction on thermal conductivity and shear strength of the epoxy composites reinforced by various silane‐functionalized hybrids of sulfhydryl‐grafted multi‐walled carbon nanotubes (SH‐MWCNTs) and vinyl‐grafted MWCNTs (CC‐MWCNTs). The results of Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, thermal gravimetric analysis (TGA), and transmission electron microscopy (TEM) show that the sulfhydryl groups and vinyl groups are successfully grafted onto the surface of MWCNTs, after treatment of MWCNT with triethoxyvinylsilane and 3‐mercaptopropyltrimethoxysilane, respectively. Scanning electron microscopy (SEM), HotDisk thermal constant analyzer (HotDisk), optical microscope, and differential scanning calorimetry (DSC) are used to characterize the resultant composites. It is demonstrated that the hybrid of 75 wt % SH‐MWCNTs and 25 wt % CC‐MWCNTs has better dispersion and stability in epoxy matrix, and shows a stronger synergistic effect in improving the thermal conductivity of epoxy composite via the thiol‐ene click reaction with 2,2′‐azobis(2‐methylpropionitrile) as thermal initiator. Furthermore, the tensile shear strength results of MWCNT/epoxy composites and the optical microscopy photographs of shear failure section indicate that the composite with the hybrid MWCNTs has higher shear strength than that with raw MWCNTs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44579.     

Interaction Between Fumed-Silica and Epoxidized Natural Rubber

Epoxidized natural rubber (ENR)/fumed silica vulcanizates were prepared by mechanical mixing method. Fumed silica content can affect mechanical properties of the composites, and ten parts per hundreds of rubber (phr) fumed silica lead to the best tensile strength. The interaction between ENR and fumed silica was characterized by Kraus equation, crosslink density (tested by NMR), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA) and scanning electron microscope (SEM). The results showed that the dispersion of silica in ENR was better than in natural rubber (NR), hydrogen bond was produced between ENR and fumed-silica in ENR/silica blends, and glass transition temperature of ENR/silica vulcanizate was higher than pure ENR vulcanizate. TGA and DMA confirmed that there was intense interaction between ENR and silica.     

Nanosize Polyacrylamide/SiO2 Composites by Inverse Microemulsion Polymerization

Nanosize polyacrylamide/silica (PAM/SiO₂) composites were prepared by water- in-oil (W/O) microemulsion process. In this system, aqueous solution of acrylamide containing disperse 10 nm size silicon dioxide was used as the dispersed phase of the microemulsion while the dispersion medium was sodium bis (2-ethylhexyl) sulfosuccinate (AOT)/toluene solution. The size of the synthesized PAM/SiO₂ nanocomposites was 38–76 nm as determined by dynamic light scattering (DLS). The incorporation of nanosize silica filler reduces the particle size of PAM latex. It had also been found that the size of composite particles decreases with increasing filler loading along with better polydispersity. The presence of silica particles in the polymer latex particles and interaction of polymer chains with silica particles in hybrid nanocomposites were characterized by Fourier transform infra red spectrophotometry (FTIR), thermogravimetry analysis (TGA) and differential scanning calorimetry (DSC). The TGA results showed improved thermoresistance and high thermal stability behavior of hybrid composites. The DSC measurements revealed that the incorporation of filler favors crystallization, increases the enthalpy of melting and thermal stabilization of the synthesized composite particles. A scanning electron microscope (SEM) was used to study the morphology and topography of the prepared nanocomposites.     

稀土钕与聚氨酯PU相互作用的研究

以DMF为溶剂,合成不同n(NCO):n(OH)的聚氨酯(PU),将稀土钕盐掺入聚氨酯制得含稀土和高分子的复合材料.采用红外(FT-IR)、紫外-可见(UV-Vis)、差示扫描量热-热重分析(DSC-TGA)、荧光(FS)等手段对聚氨酯和复合材料进行了表征.红外先谱研究结果表明,钕离子与聚氨酯分子发生了作用;荧光光谱表明,复合材料发出钕的特征荧光,这为进一步研究稀土/高分子材料的性能提供了依据.     

聚丙烯/废印刷电路板非金属粉复合材料的结构与性能

以废印刷电路板非金属粉(废PCB粉)为填料,采用熔融共混法制备了聚丙烯/废印刷电路板非金属粉复合材料,通过差示扫描量热分析(DSC) 、热重分析(TGA)、动态力学性能分析(DMA) 和扫描电镜分析（SEM）等方法,研究了废PCB粉和PP在不同质量配比下,复合材料的结晶熔融行为、热稳定性能、动态力学性能和冲击断面形貌。结果显示：随着废PCB粉的加入,复合材料的结晶速率和结晶度提高,热稳定性增强,储能模量得到提高,但熔点、力学损耗因子峰值和玻璃化转变温度有所下降;废PCB粉均匀分布于PP基体中,界面黏结性较好。     

Preparation and characterization of fluorescent polymer magnetic particles

Magnetic iron oxide (maghemite, Fe₃O₄) particles were encapsulated with fluorescent polymer phase. The resulting fluorescent magnetic polymer particles were characterized by Fourier transform infrared spectroscopy (FTIR), thermal gravimeter analysis (TGA), reflection optical microscopy, differential scanning calorimeter (DSC), Fritsch particle sizer, scanning electron microscopy (SEM), powder X‐ray diffractometer (XRD), and vibrating sample magnetometer (VSM) measurements. FTIR and XRD confirmed the presence of iron oxide in polymer phase. The TGA and DSC measurements indicated that the magnetic polymer particles have more than 50% iron oxide content and high thermal stability. SEM and reflection optical microscopy under UV light revealed that all maghemite particles were embedded in the polymer spheres and have fluorescent characteristics. The size‐distribution analysis of prepared magnetic particles was shown that the means diameter of the particles slightly increased. According to our magnetometry data, shape of the loops evidences the ferromagnetic character of the material and no evidence of superparamagnetism was seen. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation of polybenzimidazole/functionalized carbon nanotube nanocomposite films for use as protective coatings

Functionalized multi‐walled carbon nanotubes (MWCNTs) via microwave‐induced polymerization modification route, and polybenzimidazole (PBI) nanocomposite films containing 0.1‐5 wt% functionalized MWCNTs were successfully synthesized. The functionalized MWCNTs were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and X‐ray photoelectron spectroscopy (XPS). The results verify that the polymer was successfully grafted to the MWCNTs with a polymer layer that was several nanometers thick. The TGA results showed that the quantity of the attached polymer reached approximately 9.4 wt%. The mechanical properties of the nanocomposite films were measured by tensile test and dynamic mechanical analysis (DMA). The tensile test results indicated that the Young's modulus increased by about 43.9% at 2 wt% CNT loading, and further modulus growth was observed at higher filler loading. The DMA studies indicated that the nanocomposite films had a higher storage modulus than pure PBI film in the temperature range of 30‐300°C, and the storage modulus was maintained above 0.82 GPa. Simulation results confirmed that the PBI nanocomposite films had desirable mechanical properties for use as a protective coating. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers.     

Tire rubber–sisal composites: Effect of mercerization and acetylation on reinforcement

Tire rubber particles were mixed randomly with short sisal fibers and hot pressed. Sisal fibers were used as received, mercerized, and mercerized/acetylated. The fibers were characterized by scanning electron microscopy (SEM), thermal gravimetry analysis (TGA), infrared spectroscopy (FTIR), water sorption, and mechanical properties. Thermal stability of the mercerized/acetylated fibers improves (from 200 to 300°C) with respect to the raw fibers, and water sorption is ～ 20% smaller than for the raw and the mercerized fibers. Tensile strength is unchanged after the chemical treatments. Water sorption, mechanical properties, and SEM evaluated the performance of the tire rubber composites. All composites showed enhanced elastic modulus; increase is dependent on fiber load. Smallest water sorption was obtained in composites with the mercerized/acetylated fibers. With these fibers at 10% load, the best results were obtained with the smaller tire rubber particles (320 μm) and at 5% load with the bigger (740 μm) tire rubber particles. Both composites showed ～ 50% increase in tensile strength when compared to similar composites with raw fibers. SEM of the surface of fracture showed that the adhesion between fiber and rubber was enhanced after both chemical treatments. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2507–2515, 2003     

Partially Sulfonated Poly(1,4‐phenylene ether‐ether‐sulfone) and Poly(vinylidene fluoride) Blend Membranes for Fuel Cells

Blend membranes based on high conductive sulfonated poly(1,4‐phenylene ether‐ether‐sulfone) (SPEES) and poly(vinylidene fluoride) (PVDF) having excellent chemical stability were prepared and characterized for direct methanol fuel cells. The effects of PVDF content on the proton conductivity, water uptake, and chemical stability of SPEES/PVDF blend membranes were investigated. The morphology, miscibility, thermal, and mechanical properties of blend membranes were also studied by means of scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA) measurements. The blend membrane containing 90 wt.% SPEES (degree of sulfonation – DS = 72%) and 10 wt.% PVDF (M_w = 180,000) exhibits optimum properties among various SPEES72/PVDF membranes. Addition of PVDF enhanced resistance of the SPEES membrane against peroxide radicals and methanol significantly without deterioration of its proton conductivity. It's proton conductivity at 80 °C and 100% relative humidity is higher than Nafion 115 while it's methanol permeability is only half of that of Nafion 115 at 80 °C. The direct methanol fuel cell performance of the SPEES membranes was better than that of Nafion 115 membrane at 80 °C.     

乙二醇双硬脂酸酯/PMMA核壳储能微胶囊制备

以BPO-DMA为氧化还原引发剂,在室温下悬浮聚合法制备了核壳结构的乙二醇双硬脂酸酯（EGDS）- PMMA相变材料微胶囊。采用扫描电镜（SEM）、红外光谱仪（FTIR）、差示扫描量热仪（DSC）和热重分析仪（TG）表征了核壳结构微胶囊的形貌、化学结构及热性能。结果表明,当BPO加入量为1%,DMA为0.2% 时,所得微胶囊成均匀球形,粒径分布在1～5 μm范围;微胶囊相变潜热随芯壳比的增加而增大,最大相变潜热达85.34 J/g,芯材含量达64.6%,且相变材料的热稳定性显著增强。