Inactivation of pathogenic Klebsiella pneumoniae by CuO/TiO2 nanofibers: A multifunctional nanomaterial via one-step electrospinning

The fabrication and characterization of one-dimensional CuO/TiO₂ nanofibers with high photocatalytic and antibacterial activities are presented. The CuO/TiO₂ nanofibers were prepared by electrospinning of colloid composed of titanium isopropoxide, poly(vinylpyrroliodine) (PVP) and copper nanoparticles and calcination at 700 °C in air for 1 h. The antibacterial activity was tested using Klebsiella pneumoniae as model organism by calculation of the minimum inhibitory concentration (MIC). The obtained CuO/TiO₂ nanofibers showed prominent photocatalytic activity under visible light to degrade reactive black5 and reactive orange16 dyes in aqueous solutions and effectively catalyze K. pneumoniae inactivation. The decomposition process of the cell wall and cell membrane was directly observed by TEM analysis after the exposure of the K. pneumoniae to the nanofibers. Interestingly, the introduced photocatalyst can be reused with the same photocatalytic activity. Overall, the combination of CuO and TiO₂ can be synergistic and resulted in CuO/TiO₂ composite nanofibers having superior photocatalytic and antimicrobial potential to impede K. pneumoniae growth which causes bacterium to die ultimately.     

TiO2 nanofibers doped with rare earth elements and their photocatalytic activity

In the present study rare earth doped (Ln³⁺–TiO₂, Ln = La, Ce and Nd) TiO₂ nanofibers were prepared by the sol–gel electrospinning method and characterized by XRD, SEM, EDX, TEM, and UV-DRS. The photocatalytic activity of the samples was evaluated by Rhodamine 6G (R6G) dye degradation under UV light irradiation. XRD analysis showed that all the synthesized pure and doped titania nanofibers contain pure anatase phase at 500 °C but at 700 °C it shows both anatase and rutile phase. XRD result also shows that Ln³⁺-doped titania probably inhibits the phase transformation. The diameter of nanofibers for all samples ranges from 200 to 700 nm. It was also observed that the presence of rare-earth oxides in the host TiO₂ could decrease the band gap and accelerate the separation of photogenerated electron–hole pairs, which eventually led to higher photocatalytic activity. To sum up, our study demonstrates that Ln³⁺-doped TiO₂ samples exhibit higher photocatalytic activity than pure TiO₂ whereas Nd³⁺-doped TiO₂ catalyst showed the highest photocatalytic activity among the rare earth doped samples.     

Effect of polymer concentration,needle diameter and annealing temperature on TiO2-PVP composite nanofibers synthesized by electrospinning technique

In this study, TiO₂-PVP nanofibers were successfully synthesized on an aluminium collector by using cost-effective electrospinning technique. The nanofibers were prepared at different polymer concentrations, needle diameters and annealing temperatures and properties were studied by various characterizations. The structural properties were studied by X-ray diffraction (XRD) and Raman spectroscopy techniques. Surface morphology and elemental analysis of the samples were investigated by scanning electron microscopy (SEM) attached with energy dispersive spectroscopy (EDS). The optical properties were carried out by UV–Visible absorption spectroscopy (UV–Vis). By varying the polymer concentration and needle diameter, the effect of viscosity and surface tension on the formation of TiO₂-PVP nanofibers was clearly observed by SEM micro images. EDS spectrum shows effective composition of pure TiO₂ nanofibers. XRD peaks observed at temperatures 500 °C, 700 °C and 900 °C confirmed the anatase, mixed and rutile phases of TiO₂ nanofibers respectively. Raman studies also confirmed these phases of TiO₂ nanofibers. The optical band-gap values calculated using Kubelka-Munk function lies in the range of 3.02–3.22 eV.     

Enhanced photocatalytic activity of electrospun TiO2/ZnO nanofibers with optimal anatase/rutile ratio

The photocatalytic characteristics of the TiO₂/ZnO nanofibers synthesized by electrospinning followed by calcinating at different temperatures to alter the anatase-to-rutile ratio are investigated. The results demonstrate that the photocatalytic activity of TiO₂/ZnO nanofibers is enhanced by optimizing the anatase/rutile ratio among the trade-off effects of the band-gap energy, the electron/hole recombination rate, and the surface area. When calcined at 650 °C, the TiO₂/ZnO nanofibers with optimal anatase/rutile ratio (48:52) balancing these trade-off effects have the highest photocatalytic efficiency both in the degradation of RhB in liquid and conversion of NO gas.     

A VOx/meso-TiO2 catalyst for methanol oxidation to dimethoxymethane

Mesoporous TiO₂ was prepared by simply controlling the hydrolysis of Ti(OBu)₄ with the help of acetic acid. The mesoporous TiO₂ had a well-crystallized anatase phase and a high surface area of 290 m² g⁻¹ with a pore size of about 4 nm. The anatase phase and the mesoporous structure were maintained in the VO_x/TiO₂ catalyst with a monolayer dispersion of V₂O₅, however, the surface area decreased to 126 m² g⁻¹. The catalyst was highly active and selective for methanol oxidation, giving about 55% conversion of methanol and 85% selectivity to dimethoxymethane at 423 K.     

Electrospun titanium dioxide nanofiber humidity sensors with high sensitivity

Titanium dioxide nanofibers were synthesized using electrospinning technique. The nanofibers were porous with an average diameter and length of ～150 nm and 200 μm, respectively. Humidity-sensing devices were fabricated by lithographically defined aluminum electrodes on top of the nanofibers deposited on silicon dioxide grown thermally on a silicon substrate. The performance of a TiO₂ nanofiber humidity sensor was tested by AC and DC electrical measurements at 40–90% relative humidity. The response and the recovery time were 1 s and 4 s, respectively, between 40% and 90% relative humidity. The sensitivity of the TiO₂ humidity sensor in the range of 40–90% RH was 150 MΩ/%RH and 20 MΩ/%RH at 10 Hz and 100 Hz, respectively. The excellent sensing characteristics are attributed to the porous nature and the small diameter of the nanofibers.     

A comparative study of the water gas shift reaction over platinum catalysts supported on CeO2, TiO2 and Ce-modified TiO2

WGS reaction has been investigated on catalysts based on platinum supported over CeO₂, TiO₂ and Ce-modified TiO₂. XPS and XANES analyses performed on calcined catalysts revealed a close contact between Pt precursors and cerium species on CeO₂ and Ce-modified TiO₂ supports. TPR results corroborate the intimate contact between Pt and cerium entities in the Pt/Ce–TiO₂ catalyst that facilitates the reducibility of the support at low temperatures while the Ce–O–Ti surface interactions established in the Ce-modified TiO₂ support decreases the reduction of TiO₂ at high temperature. The changes in the support reducibility leads to significant differences in the WGS activity of the studied catalysts. Pt supported on Ce-modified TiO₂ support exhibits better activity than those corresponding to individual CeO₂ and TiO₂-supported catalysts. Additionally, the Ce–TiO₂-supported catalyst displays better stability at reaction temperatures higher than 573 K that observed on pure TiO₂-supported counterpart. Activity measurements, when coupled with the physicochemical characterization of catalysts suggest that the modifications in the surface reducibility of the support play an essential role in the enhancement of activity and stability observed when Pt is supported on the Ce-modified TiO₂ substrate.     

Effect of collector grounding on directionality of electrospun titania fibers

TiO₂ nanofibers were prepared by using electrospun TiO₂/polyvinylpyrrolidone fibers by drying for 5 h in air and subsequent annealing for 3 h at 500 °C. Uniform and smooth fibers with diameters of 120 ± 10 nm were observed at a PVP concentration of 0.09 g/ml, a Ti(OCH(CH₃)₂)₄ concentration of 0.14 g/ml, a flow rate of 0.5 ml/h, and an electric field of 1 kV/cm, respectively. TiO₂/PVP nanofibers were also electrospun by varying the collector grounding design to improve the axial alignment of fibers. The collector is composed of two pieces of conductive substrates separated by a gap of 1.5 mm. In addition, the collector consisting of two sets of substrates placed by 90° are prepared for a grid structure of the fibers. Both collectors show that the charged nanofibers are stretched to span across the gap between the electrodes.     

TiO2 nanofibers assembled on graphene-silver platform as a visible-light photo and bio-active nanostructure

The heterogeneous titanium oxide-reduced graphene oxide-silver (TiO₂/RGO/Ag) nanocomposites were successfully prepared by incorporation of two dimensional (2D) RGO nanosheets and spherical silver nanoparticles (NPs) into the 1D TiO₂ nanofibers. The novel TiO₂/RGO/Ag nanocomposites were synthesized by loading TiO₂ nanofibers, prepared via electrospinning technique, on the RGO/Ag platform. The resulting nanocomposites have been characterized using various techniques containing transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and ultra-violet-visible (UV–vis) spectroscopy. Microscopic studies clearly verified the existence of TiO₂ nanofibers with Ag NPs on the surface of RGO sheet and formation of TiO₂/RGO/Ag nanocomposites. Moreover, the results of UV–vis spectroscopy demonstrated that TiO₂/RGO/Ag nanocomposites extended the light absorption spectrum toward the visible region and significantly enhanced the visible-light photocatalytic performance of the prepared samples on degradation of rhodamine B (Rh. B) as a model dye. It was found that, incorporation of 50 µl RGO/Ag into the TiO₂ nanofibers lead to a maximum photocatalytic performance. Also, the improvement of the inactivation of Escherichia coli (E. coli) bacteria under visible-light irradiation was revealed by introduction of RGO/Ag into the TiO₂ matrix. The significant enhancement in the photo and bio-activity of TiO₂/RGO/Ag nanocomposites under visible-light irradiation can be ascribed to the RGO/Ag content by acting as electron traps in TiO₂ band gap.     

Preparation and characterization of CeO2–TiO2 support for Ru catalysts: Application in CWAO of p-hydroxybenzoic acid

The catalytic wet air oxidation of aqueous solutions of p-hydroxybenzoic acid has been carried out over CeO₂–TiO₂ supported ruthenium catalysts (Ru/Ce–Ti) at 140 °C and 50 bar of air. High activity of ruthenium supported catalysts was observed. It was found that the decrease of the molar ratio Ce/Ti from 3 to 1/3, improves the activity of Ru catalysts. The activity of the samples decreases in the following order: Ru/Ce–Ti (1/3) > Ru/CeO₂ ≈ Ru/TiO₂ > Ru/TiO₂DT51. Characterization of samples was performed by means of N₂ adsorption–desorption, XRD, UV–visible, TPR, SEM and TEM.     

Novel Ti-KIT-6 material for the photocatalytic reduction of carbon dioxide to methane

Novel Ti-KIT-6 materials with different Si/Ti ratios (200, 100 and 50) have been synthesized, characterized and applied for the photocatalytic reduction of carbon dioxide to methane. An intermediate amount of Ti(Si/Ti = 100) was found to be isolated and uniformly distributed, without collapsing the KIT-6 structure. TiO₂ formation was observed due to a higher amount of Ti(Si/Ti = 50). Overall, the Ti-KIT-6 (calcined) materials were superior in activity than the Ti-KIT-6 (dried) materials. Owing to the greater number of OH groups, the Si/Ti ratio of 100 showed a higher methane production rate and was found to be more reactive than commercial Degussa P25 TiO₂.     

Fabrication and characterization of new bulky layer mixed metal oxide ceramic nanofibers through two nozzle electrospinning method

New bulky layers of metal mixed ceramic nanofibers were fabricated through two-nozzle electrospinning method followed by calcination. Solutions of PAN in DMF with various concentrations were prepared as: 11, 12, 13, 14, and 15 wt% to which the constant amounts of 2.1 g of Aluminum acetate, 0.3 g of Copper acetate and 0.3 g of Boehmite nanoparticles were added. A stepwise calcination process was utilized to obtain the ceramic nanofibers. The nanofibers were characterized by FTIR spectroscopy, TG-DTA, XRD, SEM and EDS techniques. The formulation with 12 wt% of PAN in DMF was proved to be the optimum spinable sample. The average diameter of as spun nanofibers was detected as 568 nm, which decreased to 181 nm after calcination and thermal degradation. Ceramic nanofibers were composed of CuO, Al₂O₃ and Cu₂Al₄O₇ phases. The average density of the sample was about 0.090 (g/cm³) and the porosity of the mat was 94.5% and thus, production of a 3D structure may be claimed. The ceramic nanofibers performed well as catalyst in the C-C coupling reaction (Suzuki reaction) by facilitating the synthesis of biaryl compound from aryl iodide in 20 min with isolated yield of 89% only by using 15 mg of ceramic nanofibers as the nano catalyst.     

Encapsulation of manganese oxides nanocrystals in electrospun carbon nanofibers as free-standing electrode for supercapacitors

Flexible composites with manganese oxides (MnO_x) nanocrystals encapsulated in electropun carbon nanofibers were successfully fabricated via a simple and practical combination of electrospinning and carbonization process. The as-formed MnO_x/carbon nanofibers composites have a rough surface with MnO_x nanoparticles well embedded in the carbon nanofibers backbones. When used as electrodes for supercapacitor, the resulting MnO_x/carbon nanofiber composites exhibit good electrochemical performance with a specific capacitance of 174.8 F g⁻¹ at 2 mV s⁻¹ in 0.5 M Na₂SO₄ electrolyte, a good rate capability at high current density and long-term cycling stability. It is expected that such freestanding composites could be promising electrodes for high-performance supercapacitors.     

Water gas shift reaction kinetics in Fischer–Tropsch synthesis over an industrial Fe–Mn catalyst

The kinetics of water gas shift (WGS) reaction over an Fe–Mn catalyst under Fischer–Tropsch synthesis (FTS) reaction conditions is studied in a spinning basket reactor. Experimental conditions are varied as follows: temperature of 533–573 K, reactor pressure of 10.0–26.5 bar, H₂/CO feed ratio of 0.66–2.0 and space velocity of 0.66–2.65×10⁻³ Nm³ kg_cat⁻¹ s⁻¹. By separately fitting WGS kinetics parameters with experimental data, which is possible in the spinning basket reactor with neglecting concentration and temperature gradients, different kinetics models of WGS are derived and discriminated on the basis of four sets of WGS elementary reactions. Kinetics experimental results show that the WGS reaction under FTS reaction conditions is far from equilibrium. Two types of WGS mechanisms are investigated. One is the formate mechanism, and the other is the direct oxidation mechanism. It is found that the formate mechanism is better in fitting experimental data than the direct oxidation mechanism over the Fe–Mn catalyst under the FTS reaction conditions. The optimized kinetics model with formate intermediate dissociation as the rate-determining step (RDS) can fit the WGS experimental results well. The simplified WGS kinetics model can easily be used for industrial modeling applications.     

Slurry explosive detonation synthesis and characterization of 10 nm TiO2

TiO₂ was prepared by detonating a slurry explosive made of Ti precursor, ammonium nitrate, cyclotrimethylenetrinitramine (RDX), and polystyrene (EPS). X-ray diffraction, transmission electron microscopy, energy dispersive X-ray spectrometry, Fourier transform infrared spectroscopy, and UV–vis diffuse reflection spectroscopy revealed that the sample was composed of mixed crystals of rutile and anatase TiO₂ with irregular spherical shapes and 10 nm particle size. The minimum energy gap of the sample was 2.9 eV. An ideal TiO₂ explosive was prepared from a precursor/ammonium nitrate/RDX ratio of 1:1:0.6 and 2 g of EPS as a density modifier.     

Raman spectra and extended X-ray absorption fine structure characterization of La(2−x)/3NaxTiO3 and Nd(2−x)/3LixTiO3 microwave ceramics

A-site deficient perovskite compounds, La_(2?x)/3Na_xTiO₃ (0.02 ≤ x ≤ 0.5) and Nd_(2?x)/3Li_xTiO₃ (0.1 ≤ x ≤ 0.5) microwave ceramics, were investigated by Raman scattering. Nd_(2?x)/3Li_xTiO₃ (0.1 ≤ x ≤ 0.5) was also investigated by extended X-ray absorption fine structure (EXAFS) measurement. The Raman shifts of the E (239 cm^?1) and A₁ (322 cm^?1) modes of La_(2?x)/3Na_xTiO₃ were found to decrease with x. However, the E (254 cm^?1) and A₁ (338 cm^?1) of Nd_(2?x)/3Li_xTiO₃ were found to blueshift with x, which was caused by Li substitution. The redshift of the A₁ (471 cm^?1) phonon of Nd_(2?x)/3Li_xTiO₃ (0.1 ≤ x ≤ 0.3) indicates that O–Ti–O bonding forces lessen with Li concentration, which is consistent with the EXAFS result that Ti–O bond lengths increase for 0.1 ≤ x ≤ 0.3. For x > 0.3, the EXAFS result shows that Ti–O bond lengths decrease. Moreover, Ti–O bond lengths show strong correlation with the microwave dielectric constants of Nd_(2?x)/3Li_xTiO₃.     

Effect of TiO2 on hydrodenitrogenation performances of MCM-41 supported molybdenum phosphides

The effect of TiO₂ on the hydrodenitrogenation (HDN) performance of MoP/MCM-41 was investigated using quinoline and decahydroquinoline as the model molecules. The catalysts were characterized by XRD, CO chemisorption, TEM, TPR and pyridine FT-IR. Addition of TiO₂ enhanced the C–N bond cleavage activity of MoP/MCM-41 but inhibited its dehydrogenation activity. A maximum HDN activity was observed when the TiO₂ loading was 5 wt%. The characterization results indicated that introduction of TiO₂ did not affect the formation of MoP phase. The TiO₂-containing catalysts possessed higher CO uptake than MoP/MCM-41, but no significant differences in the acid properties and particle size distributions were observed for all the catalysts. XPS results revealed a surface enrichment of TiO₂ in Ti-containing catalysts and small amount of these surface TiO₂ can be partially reduced to Tiⁿ⁺ (n < 4). It is suggested that these Tiⁿ⁺ (n < 4) species may be responsible for the promoting effect of TiO₂ on the HDN performance of MoP/MCM-41.     

Control of refractive index by annealing to achieve high figure of merit for TiO2/Ag/TiO2 multilayer films

We modified the refractive index (n) of TiO₂ by annealing at various temperatures to obtain a high figure of merit (FOM) for TiO₂/Ag/TiO₂ (45 nm/17 nm/45 nm) multilayer films deposited on glass substrates. Unlike the as-deposited and 300 °C-annealed TiO₂ films, the 600 °C-annealed sample was crystallized in the anatase phase. The as-deposited TiO₂/Ag/as-deposited TiO₂ multilayer film exhibited a transmittance of 94.6% at 550 nm, whereas that of the as-deposited TiO₂/Ag/600 °C-annealed TiO₂ (lower) multilayer film was 96.6%. At 550 nm, n increased from 2.293 to 2.336 with increasing temperature. The carrier concentration, mobility, and sheet resistance varied with increasing annealing temperature. The samples exhibited smooth surfaces with a root-mean-square roughness of 0.37–1.09 nm. The 600 °C-annealed multilayer yielded the highest Haacke's FOM of 193.9×10⁻³ Ω⁻¹.     

Low-temperature continuous wet oxidation of trichloroethylene over CoOx/TiO2 catalysts

TiO₂-supported metal oxides such as CoO_x, CuO_x, NiO_x and FeO_x have been used for catalytic wet oxidation of trichloroethylene (TCE) in a continuous flow type fixed-bed reactor system, and the most promising catalyst for this wet catalysis has been characterized using XPS and XRD techniques. All the supported catalysts gave relatively low conversions for the wet oxidation at 36 °C, except for 5 wt% CoO_x/TiO₂ which exhibited a steady-state conversion of 45% via a transient activity behavior up to 1 h on stream. XPS measurements yielded that a Co 2p_3/2 main peak at 779.8 eV appeared with the 5 wt% CoO_x/TiO₂ catalyst after the continuous wet TCE oxidation at 36 °C for ca. 6 h (spent catalyst) and this binding energy value was equal to that of Co₃O₄ among reference Co compounds used here, while the catalyst calcined at 570 °C (fresh catalyst) possessed a main peak at 781.3 eV, very similar to that for CoTiO_x species such as CoTiO₃ and Co₂TiO₄. Only characteristic reflections for Co₃O₄ were indicated upon XRD measurements even with the fresh catalyst sample. The simplest model, based on these XPS and XRD results, for nanosized Co₃O₄ particles existing with the fresh catalyst could reasonably explain the transient activity behavior observed upon the wet TCE oxidation.     

Synthesis and characterization of Ba1−xSrxTiO3 nanopowders by citric acid gel method

Stoichiometric and monophasic Ba_1−xSr_xTiO₃ (x = 0.3) nanopowders were successfully prepared by the citric acid gel method using barium nitrate, strontium nitrate and tetra-n-butyl titanate as Ba, Sr, Ti sources and citric acid as complexing reagent. Thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), infrared (IR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to characterize the thermal decomposition behavior, the crystallization process and the particle size and morphology of the calcined powders. The results indicated that single-phase and well-crystallized Ba_1−xSr_xTiO₃ (x = 0.3) nanopowders with particle size around 80 nm could be obtained after calcining the dried gel at 950 °C for 2 h.