Effect of molar ratio of TiO2/SiO2 on the properties of particles synthesized by flame spray pyrolysis

Titania (TiO₂)–silica (SiO₂) nanoparticles were synthesized from sprayed droplets of a mixture of TEOS and TTIP by flame spray pyrolysis (FSP). The effect of molar ratio between TEOS and TTIP in the mixture on the particle properties such as particle morphology, average particle diameter, specific surface area, crystal structure, etc., were determined using TEM, XRD, BET, and FT-IR. A UV-spectrometer was also used to measure the absorption spectrum and the band gap energy of the product particles. As the molar ratio of TEOS/TTIP increased by increasing TEOS concentration at the fixed TTIP concentration, the average particle diameter of the mixed oxide nanoparticles increased with maintaining uniform dispersion between TiO₂ and SiO₂, and crystal structure was transformed from anatase to amorphous. The band gap energy of the TiO₂–SiO₂ nanoparticles increased with respect to the increase of the molar ratio due to the decrease of width of UV-absorption spectrum. Photocatalytic activity of TiO₂–SiO₂ composite particles decreased with the concentration of TEOS.     

Solid acidities of SiO2–TiO2/montmorillonite composites synthesized under different pH conditions

SiO₂–TiO₂/montmorillonite composites were prepared under acidic, neutral and basic conditions and the solid acidity of the resulting composites were determined. All the SiO₂/TiO₂ ratio of the colloidal particles was set at 10 but the resulting SiO₂/TiO₂ ratios were significantly richer in TiO₂. The XRD patterns of the acidic composite showed expanding and broadening of the (001) reflection by intercalation of colloidal SiO₂–TiO₂ particles, but the neutral and basic composites showed only broadening of the reflections and no intercalation. The specific surface areas of the acidic, neutral and basic composites (375, 237 and 247 m²/g, respectively) were much larger than of montmorillonite (6 m²/g). The average pore sizes were about 4, 15 and 50 nm, and the amounts of solid acidic sites measured by the NH₃-TPD were 178, 95 and 86 µmol/g for the acidic, neutral and basic composites, respectively. The solid acid amount of the acidic composite was twice that of a commercial catalyst, K-10, (85 µmol/g) and much higher than the guest phase SiO₂–TiO₂ gel (16 µmol/g) or the host phase montmorillonite (6 µmol/g). The TPD peak temperatures reflect the acid strength, and were similar in all the samples, ranging from 175° to 200 °C.     

Impact of supercritical drying and heat treatment on physical properties of titania/silica aerogel monolithic and its applications

TiO₂–SiO₂ monolithic aerogels were homogeneously prepared using sol–gel method. Critical point of drying of TiO₂–SiO₂ gels with ethanol was studied for 30, 60, 90 and 120 min. Subsequently, the gels were dried with supercritical ethanol, resulting in amorphous aerogels that crystallized following heat treatment at 550 °C from 1 to 5 h. The TiO₂–SiO₂ aerogels were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and surface area measurements. The molar ratio of SiO₂:TiO₂ was 6 and the synthetic strategy revealed that TiO₂–SiO₂ aerogel, had a surface area 868 m²/g, particle size 40 nm, density 0.17 g/cm³ and 80% porosity. The finding indicated that from economic point of view, TiO₂–SiO₂ gel should be supercritical dried for 30 min and heat-treated for 5 h. The TiO₂–SiO₂ aerogel monoliths photocatalyst synthesized using sol–gel method provided insight into the characteristics that make a photocatalyst material well-suited for photodegradation of phenol and cyanide in an industrial waste stream containing Cl⁻, S²⁻ and NH₄⁺. Interestingly, after multiple reuse cycles (i.e. ≥7), photodegradation systems with regenerated photocatalyst showed a slightly decreasing of photoactivity 2–4%. The overall kinetics of photodegradation of either phenol or cyanide using TiO₂–SiO₂ aerogel photocatalyst was found to be of first order.     

Oxidation of CH4 over Pd supported on TiO2-doped SiO2: Effect of Ti(IV) loading and influence of SO2

Titania-modified silicas with different weight% of TiO₂ were prepared by sol–gel method and used as supports for Pd (1 wt%) catalysts. The obtained materials were tested in the oxidation of methane under lean conditions in absence and in presence of SO₂. Test reactions were consecutively performed in order to evaluate the thermal stability and poisoning reversibility. Increasing amounts of TiO₂ improved the catalytic activity, with an optimum of the performance for 10 wt% TiO₂ loading. Moreover, the titania-containing catalysts exhibited a superior tolerance towards SO₂ by either adding it to the reactants or feeding it as a pure pretreatment atmosphere at 350 °C. Catalysts were characterized by XPS, XRD, FT-IR and BET measurements. According to the structural and surface analyses, the mixed oxides contained Si–O–Ti linkages which were interpreted as being responsible for the enhanced intrinsic activity of supported PdO with respect to PdO on either pure SiO₂ or pure TiO₂. Moreover, the preferential interaction of the sulfur molecule with TiO₂ and the easy SO_x desorption from high surface area silica were the determining factors for the superior SO₂ tolerance of the TiO₂-doped catalysts.     

Oxidative carbonylation of methanol to dimethyl carbonate over CuCl/SiO2–TiO2 catalysts prepared by microwave heating: The effect of support composition

Copper(I) chloride catalysts with a loading of 20 wt%, supported on silica–titania mixed oxides with Si/Ti ratios of 1, 5, 10 and 50 were prepared by conventional and microwave heating methods and tested in the oxidative carbonylation of methanol to dimethyl carbonate (DMC). X-ray diffraction (XRD), nitrogen adsorption, X-ray photoelectron spectroscopy (XPS) and thermal gravimetric analysis (TGA) were used to examine the bulk and surface properties of the CuCl/SiO₂–TiO₂ catalysts. Quantum-chemical calculations were performed to explore the interaction of CuCl with the silica–titania support. Microwave heating showed some significant advantages over the conventional heating method, with markedly reduced preparation temperature and time, and provided improved catalytic activity in the oxidative carbonylation of methanol. The catalytic behavior of CuCl/SiO₂–TiO₂ in the test reaction studied was strongly dependent on the support composition. Incorporation of tetrahedral Ti(IV) species into the silica matrix could enhance the interaction of copper species with the oxide support. The improved catalytic performance of CuCl/SiO₂–TiO₂ in the DMC synthesis can be understood by the existence of the strong coordination interactions between the Cu⁺ centers of CuCl and the bridging oxygen atoms at the Si–O–Ti bonds in the silica–titania support.     

CO hydrogenation to iso-C4 hydrocarbons over CeO2–TiO2 catalysts

CeO₂–TiO₂ (Ce:Ti = 0.25–9, molar ratio) catalysts were synthesized by a sol–gel method and the catalytic performances were evaluated in the selective synthesis of isobutene and isobutane from CO hydrogenation under the reaction conditions of 673–748 K, 1–5 MPa and 720–3000 h⁻¹. The physical properties, such as specific surface area, cumulative pore volume, average pore diameter, crystal phase and size, of the catalysts were characterized by N₂ adsorption/desorption and XRD. All the CeO₂–TiO₂ composite oxides showed higher surface areas than pure TiO₂ and CeO₂. No TiO₂ phase was detected on the samples of CeO₂–TiO₂ in which TiO₂ contents were in the range of 10–50 mol%. Crystalline Ce₂O₃ was detected in CeO₂–TiO₂ (8:2). The reaction conditions, temperature, pressure and space velocity, had obvious influences on the CO conversion and distribution of the products over CeO₂–TiO₂ (8:2) catalyst.     

Photocatalytic Properties of Silica-supported TiO2

TiO₂ supported on SiO₂ surface is effective on the recovery of photocatalyst, morphological control, and coating on the substrate. Furthermore, it shows much higher photocatalytic activity than pure TiO₂. The silica support is quite influential on the surface properties of TiO₂ supported on SiO₂. The enhanced photocatalytic activity of TiO₂–SiO₂ could be explained by the effects of surface area, adsorption, band-gap energy and local structure. However, it is difficult to say which one is the most important factor responsible for the photocatalytic property of TiO₂–SiO₂. For example, the reduction of particle size could effect on both of the surface area and band-gap energy. And, Ti–O–Si bonds could modify the band-gap energy and local structure. Therefore, the photocatalytic properties of TiO₂–SiO₂ should be expressed by sum of many factors such as surface area, adsorption, band-gap energy and local structure.     

Structure and performance of a novel TiO2-phosphonate composite photocatalyst

An innovative SiO₂-PO₄³⁻-TiO₂ photocatalyst is presented which is able to bond TiO₂ to Raschig rings (RR). Evidence for the formation on the catalyst surface of PO stretching bands near 1200–1250 cm⁻¹ is presented by FTIR spectroscopy. The TiO₂ Degussa P25 on the catalyst surface (RR) was further characterized by high-resolution transmission electron microscopy (HRTEM), and X-ray diffraction showing that the composite catalyst prepared at 500 °C does not alter the particle size or crystallographic composition of the TiO₂ Degussa P25 particles. The Ti- and P-distribution of the catalyst surface overlayers was obtained by Ar-sputtering eroding up to 100 topmost catalyst layers. By atomic force microscopy (AFM) the root mean square roughness (Rq) or rugosity of 771 nm and an average height of the catalyst layer of 1.52 μm were found on the glass surface. The root mean square roughness Rq varies very little in value before and after the photocatalysis indicating that the sample porosity is conserved during 4-CP photodegradation. The disappearance kinetics of 4-chlorophenol (4-CP) on the SiO₂-PO₄³⁻-TiO₂ composite occurred within 15 min and was faster than the 45 min needed with suspensions of TiO₂ Degussa P25 (1 g L⁻¹). The SiO₂-PO₄³⁻-TiO₂ photocatalyst was able to degrade repetitively 4-CP solutions without loss of activity. The effect of the light intensity, oxidant concentration and 4-CP concentration on the photodegradation kinetics was investigated and is reported in this study.     

Effect of TiO2 particle size on the photocatalytic reduction of CO2

Pure TiO₂ anatase particles with a crystallite diameters ranging from 4.5 to 29 nm were prepared by precipitation and sol–gel method, characterized by X-ray diffraction (XRD), BET surface area measurement, UV–vis and scanning electron microscopy (SEM) and tested in CO₂ photocatalytic reduction. Methane and methanol were the main reduction products. The optimum particle size corresponding to the highest yields of both products was 14 nm. The observed optimum particle size is a result of competing effects of specific surface area, charge–carrier dynamics and light absorption efficiency.     

Fe effect on the optical properties of TiO2:Fe2O3 nanostructured composites supported on SiO2 microsphere assemblies

The effect of Fe ion concentration on the morphological, structural, and optical properties of TiO₂ films supported on silica (SiO₂) opals has been studied. TiO₂:Fe₂O₃ films were prepared by the sol-gel method in combination with a vertical dip coating procedure; precursor solutions of Ti and Fe were deposited on a monolayer of SiO₂ opals previously deposited on a glass substrate by the same procedure. After the dip coating process has been carried out, the samples were thermally treated to obtain the TiO₂:Fe₂O₃/SiO₂ composites at the Fe ion concentrations of 1, 3, and 5 wt%. Scanning electron microscopy (SEM) micrographs show the formation of colloidal silica microspheres of about 50 nm diameter autoensembled in a hexagonal close-packed fashion. Although the X-ray diffractograms show no significant effect of Fe ion concentration on the crystal structure of TiO₂, the μ-Raman and reflectance spectra do show that the intensity of a phonon vibration mode and the energy bandgap of TiO₂ decrease as the Fe⁺³ ion concentration increases.     

Direct synthesis of mesoporous silicalite-1 supported TiO2–ZrO2 for the dehydrogenation of EB to styrene with CO2

Direct synthesis route was developed to support TiO₂–ZrO₂ binary metal oxide onto the carbon templated mesoporous silicalite-1 (CS-1). Metal hydroxide modified carbon particles could play a role as hard template and simultaneously support metal components on the mesopores during the crystallization of zeolites. Such supported TiO₂–ZrO₂ binary metal oxides (TZ/CS-1) showed better resistance to deactivation in the oxidative dehydrogenation of ethylbenzene (ODHEB) in the presence of CO₂. These catalysts were found to be active, selective and catalytically stable (10 h of time-on-stream) at 600 °C for the dehydrogenation of ethylbenzene (EB) to styrene (Sty).     

Formation and size control of titanium particles by cathode discharge electrolysis of molten chloride

Cathode discharge electrolysis of LiCl–KCl–K₂TiF₆ has been conducted under 1 atm of Ar. Near spherical particles consisting of metallic or partially oxidized titanium in the core and TiO₂ in the surface layer were obtained. The Ti particles are originally formed in the melt by reduction of Ti ions, and a surface TiO₂ layer is formed when the Ti particles are exposed to air or water. The particle sizes were in the range 10–400 nm, and were strongly dependent on electrolytic conditions, such as quantity of electricity, K₂TiF₆ concentration, bath temperature and current per melt volume. The particle growth mechanism was also investigated, and it was confirmed that reduction of ions at particle surfaces is involved in particle growth.     

The situ preparation of silica nanoparticles on the surface of functionalized graphene nanoplatelets

A method for situ preparing a hybrid material consisting of silica nanoparticles (SiO₂) attached onto the surface of functionalized graphene nanoplatelets (f-GNPs) is proposed. Firstly, polyacrylic acid (PAA) was grafted to the surface of f-GNPs to increase reacting sites, and then 3-aminopropyltriethoxysilane (APTES) KH550 reacted with abovementioned product PAA-GNPs to obtain siloxane-GNPs, thus providing reaction sites for the growth of SiO₂ on the surface of GNPs. Finally, the SiO₂/graphene nanoplatelets (SiO₂/GNPs) hybrid material is obtained through introducing siloxane-GNPs into a solution of tetraethyl orthosilicate, ammonia and ethanol for hours'' reaction. The results from Fourier transform infrared spectroscopy (FTIR) showed that SiO₂ particles have situ grown on the surface of GNPs through chemical bonds as Si-O-Si. And the nanostructure of hybrid materials was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). All the images indicated that SiO₂ particles with similar sizes were grafted on the surface of graphene nanoplatelets successfully. And TEM images also showed the whole growth process of SiO₂ particles on the surface of graphene as time grows. Moreover, TGA traces suggested the SiO₂/GNPs hybrid material had stable thermal stability. And at 900°C, the residual weight fraction of polymer on siloxane-GNPs was about 94.2% and that of SiO₂ particles on hybrid materials was about 75.0%. However, the result of Raman spectroscopy showed that carbon atoms of graphene nanoplatelets became much more disordered, due to the destroyed carbon domains during the process of chemical drafting. Through orthogonal experiments, hybrid materials with various sizes of SiO₂ particles were prepared, thus achieving the particle sizes controllable. And the factors’ level of significance is as follows: the quantity of ammonia > the quantity of tetraethyl orthosilicate (TEOS) > the reaction time.     

Role of support in reforming of CH4 with CO2 over Rh catalysts

The reforming of CH₄ with CO₂ over supported Rh catalysts has been studied over a range of temperatures (550–1000 K). A significant effect of the support on the catalytic activity was observed, where the order was Rh/Al₂O₃>Rh/TiO₂>Rh/SiO₂. The catalytic activity of Rh/SiO₂ was promoted markedly by physical mixing of Rh/SiO₂ with metal oxides such as Al₂O₃, TiO₂, and MgO, indicating a synergetic effect. The role of the metal oxides used as the support and the physical mixture may be ascribed to the promotion in dissociation of CO₂ on the surface of Rh, since the CH₄ + CO₂ reaction is first order in the pressure of CO₂, suggesting that CO₂ dissociation is the rate-determining step. The possible model of the synergetic effect was proposed.     

Meldola blue immobilized on a new SiO2/TiO2/graphite composite for electrocatalytic oxidation of NADH

Meldola blue immobilized on a new SiO₂/TiO₂/graphite composite was applied in the electrocatalytic oxidation of NADH. The materials were prepared by the sol-gel processing method and characterized by several techniques including scanning electronic microscopy coupled to energy dispersive spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS) and high-resolution transmission electronic microscopy (HRTEM). Si and Ti mapping profiles on the surface showed a homogeneous distribution of the components. Ti2p binding energy peaks indicate that the formation of Si-O-Ti linkage is presumably the responsible for the high rigidity of the matrices. The good electrical conductivity presented by the composites (5 and 11 S cm⁻¹) can be related to a homogeneous distribution of graphite particles observed by TEM. After the materials characterization, a SiO₂/TiO₂/graphite electrode was prepared and some chemical modifications were performed on its surface to promote the adsorption of meldola blue. The resulting system presented electrocatalytic properties toward the oxidation of NADH, decreasing the oxidation potential to −120 mV. The proposed sensor showed a wide linear response range from 0.018 to 7.29 mmol l⁻¹ and limit of detection of 0.008 mmol l⁻¹. SiO₂/TiO₂/graphite has shown to be a promising material to be used as a suitable support in the construction of new electrochemical sensors.     

Preparation of TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hollow spheres and their activity in methylene blue photodecomposition

PSA [poly-(styrene-methyl acrylic acid)] latex particle has been taken into account as template material in SiO₂ hollow spheres preparation. TiO₂-doped SiO₂ hollow spheres were obtained by using the appropriate amount of Ti(SO₄)₂ solution on SiO₂ hollow spheres. The photodecomposition of the MB (methylene blue) was evaluated on these TiO₂-doped SiO₂ hollow spheres under UV light irradiation. The catalyst samples were characterized by XRD, UV-DRS, SEM and BET. A TiO₂-doped SiO₂ hollow sphere has shown higher surface area in comparison with pure TiO₂ hollow spheres. The 40 wt% TiO₂-doped SiO₂ hollow sphere has been found as the most active catalyst compared with the others in the process of photodecomposition of MB (methylene blue). The BET surface area of this sample was found to be 377.6 m²g⁻¹. The photodegradation rate of MB using the TiO₂-doped SiO₂ catalyst was much higher than that of pure TiO₂ hollow spheres.     

Hybrid photocatalysts for the degradation of trichloroethylene in air

Hybrid photocatalysts based on an adsorbent SiMgOx and a photocatalyst TiO₂ were developed in a plate shape. The ceramic surface was coated with TiO₂ by the slip-casting technique. The effect of the support in the photocatalytic degradation of trichloroethylene (TCE) was analyzed by modifying TiO₂ loading and the layer thickness. Photocatalysts were characterised by N₂ adsorption–desorption, mercury intrusion porosimetry, SEM, UV–vis spectroscopy and XRD. A direct relationship between the TiO₂ content and the photocatalytic activity was observed up to three layers of TiO₂ (0.66 wt.%). Our results indicate that intermediate species generated on the TiO₂ layer can migrate through relatively long distances to react with the OH⁻ surface groups of the support. By increasing the TiO₂ loading of the photocatalyst two effects were observed: trichloroethylene conversion is enhanced, while the efficiency of the oxidation process is decreased at expenses of increasing the selectivity to COCl₂ and dichloroacetylchloride (DCAC). The results are discussed in terms of the layer thickness, TiO₂ amount, TCE conversion and CO₂, and COCl₂ selectivity.     

Photocatalytic degradation of oxalic acid on a semiconductive layer of n-TiO2 particles in a batch plate reactor. Part III: Rate determining steps and nonsteady diffusion model for oxygen transport

The effect of oxygen concentration on the photocatalytic degradation rate of oxalic acid on a fixed layer of TiO₂ particles in a batch mode plate photoreactor was investigated at various light intensities. The regions where the photocatalytical decomposition rate is controlled by the flux of oxygen, photons, or both, were identified. For low oxygen concentration (0–0.15 mol m^–3) and photon flux intensity in the range from 10 to 24 × 10^–5 einstein m^–2 s^–1 the experimentally determined photocatalytical decomposition rate was in agreement with that theoretically calculated assuming the process to be controlled by the limiting flux of oxygen to the TiO₂ surface. At higher concentrations of oxygen (0.15–0.94 mol m^–3) the rate of photocatalysis was controlled simultaneously by both the flux of oxygen and photons. The influence of the oxygen concentration decreased with decreasing photon flux. For low photon flux intensities (3.5 × 10^–5 einstein m^–2 s^–1), the reaction rate was controlled by the photon flux. The concentration profile of oxygen in the diffusion layer along the reactor plate was calculated and showed a significant decrease in oxygen concentration on the TiO₂ surface.     

Synergistic effect of TiO2 and iron oxide supported on fluorocarbon films. Part 1: Effect of preparation parameters on photocatalytic degradation of organic pollutant at neutral pH

Iron oxide and TiO₂ were immobilized on modified polyvinyl fluoride films in a sequential process. Synergic effects of iron oxide and TiO₂ on the polymer film were observed during the heterogeneous degradation of hydroquinone (HQ) in the presence of H₂O₂ at pH close to neutrality and under simulated solar irradiation. Within the degradation period, little iron leaching (<0.5 mg/L) was observed.The surface of commercial polyvinyl fluoride (PVF) film was modified by TiO₂ under light inducing oxygen group (C–OH, CO, COOH) formation on the film surface. During this treatment, TiO₂ nanoparticles simultaneously bind to the film, leading to PVF^f–TiO₂. The possible mechanistic pathway for the TiO₂ deposition and the nature of the polymer–TiO₂ interaction are discussed. Furthermore PVF and PVF^f–TiO₂ were immersed in an aqueous solution for the deposition of iron oxide layer by hydrolysis of FeCl₃, leading to PVF–Fe oxide and to PVF^f–TiO₂–Fe oxide respectively.HQ degradation and mineralization mediated by PVF^f–TiO₂, PVF–Fe oxide and PVF^f–TiO₂–Fe oxide were investigated under different conditions. Remarkable synergistic effects were observed for PVF^f–TiO₂–Fe oxide possibly due to Fe(II) regeneration, accelerated by electron transfer from TiO₂ to the iron oxide under light.     

Crystallization kinetics of amorphous alumina–zirconia–silica ceramics

Crystallization kinetics of amorphous alumina–zirconia–silica ceramics was studied by nonisothermal differential scanning calorimetry (DSC). Different amorphous materials were produced by plasma spraying of near-eutectic Al₂O₃–ZrO₂–SiO₂ mixtures. Phase composition and microstructure of the amorphous materials and nanocrystalline products were analyzed. All of the investigated materials show an exothermic peak between 940 and 990 °C in the DSC experiments. The activation energies calculated from DSC traces decrease with increasing SiO₂ concentration. Values of the Avrami coefficients together with results of the microstructural observations indicate that tetragonal zirconia crystallization from materials containing more than 10 wt.% SiO₂ proceeds by a diffusion-controlled mechanism with nucleation occurring predominantly at the beginning of the process. In contrast, material with almost no SiO₂ exhibited a value of the Avrami exponent consistent with the crystal growth governed by processes at the phase boundary.