Morphology,rheology, and mechanical properties of dynamically cured EPDM/PP blend: Effect of curing agent dose variation

The structure development, rheological behavior, viscoelastic, and mechanical properties of dynamically cured blend based on the ethylene–propylene–diene terpolymer (EPDM) and polypropylene (PP) with a ratio of 60/40 by weight were studied. The variation of two‐phase morphology was observed and compared as the level of curing agent was increased. Meanwhile, as the level of curing agent increased, viscosity as a function of shear stress always increased at a shear stress range of 2.2 × 10⁴ to 3.4 × 10⁵ Pa at the temperature of 200°C, yet viscosity of the blend approached each other at high shear stress. Dynamic mechanical spectra at different temperatures show that dynamic modulus (E′) of the blend exhibits two drastic transitions corresponding to glass transition temperature (T_g) of EPDM and T_g of PP, respectively. In the blends T_gs of EPDM increase and T_gs of PP almost remain unchangeable with an increase in curing agent level. Tensile strength increased, yet elongation at break decreased as the level of curing agent is increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 357–362, 2004     

Natural rubber/ethylene propylene diene blends for high insulation iron crossarms

This research studied the composition and behavior of natural rubber (NR) and ethylene propylene diene monomer (EPDM) blends at various carbon black concentrations (0–30 phr) in terms of electrical resistivity, dielectric breakdown voltage testing, and physical properties. The blends having electrical properties suitable for application in high‐insulation iron crossarms were selected for investigation of compatibility and increased physical properties. The effect of the homogenizing agent concentration on improvement of compatibility of blends was studied by scanning electron microscopy, pulsed nuclear magnetic resonance spectroscopy, and rheology techniques. We also examined mechanical properties such as tensile strength, tear strength, elongation at break, and hardness. The NR/EPDM blends filled with a fixed concentration of silica were investigated for ozone resistance. A carbon black content as high as 10 phr is still suitable for the insulation coating material, which can withstand electrical voltage at 10 kVac. Addition of the homogenizing agent at 5 phr can improve the mechanical compatibility of blends, as evidenced by the positive deviation of shear viscosity of the rubber blend, that is, the calculated shear viscosity being higher than that of experimental data. Moreover, the pulsed NMR results indicated that the spin‐spin relaxation (T₂) of all three components of the rubber blend was compressed upon the addition of the homogenizing agent. The ratio of NR/EPDM in the blend to best resist the ozone gas is 80/20 with the addition of silica of 30 phr into the blend. Also, the NR/EPDM filled with silica had a decreased change in thermal and mechanical properties of blends after thermal aging. The synergistic effect of silica content and high NR content (80) in 20 phr EPDM could improve antioxidation by ozone in the absence of a normal antioxidant for natural rubber. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3401–3416, 2004     

Blending of NR/BR/EPDM by reactive processing for tire sidewall applications. II. Characterization

Cure incompatibility in NR/BR/EPDM blends is a crucial problem, affecting blend properties. In a previous study, it was demonstrated that the mechanical properties of such blends can be significantly improved by utilizing a reactive processing technique, in which a pretreated EPDM is first prepared by incorporating all compounding ingredients in the EPDM and subsequent preheating, prior to crossblending with premasticated NR/BR. In the present article, the pretreated EPDM‐moieties are prepared using two different accelerators, N‐cyclohexyl‐2‐benzothiazole sulfenamide (CBS) and 6‐nitro MBTS. The latter was synthesized and applied for the purpose of IR characterization. The infrared (IR) spectra of the pretreated, extracted EPDM demonstrate absorption peaks associated with the IR absorption of the functional groups in the accelerator fragments, attached to the EPDM. NR/BR/EPDM (35/35/30) ternary blends are prepared by reactive mixing of the pretreated EPDM with CBS fragments attached with premasticated NR/BR on a two‐roll mill. Their blend morphological features are studied using the atomic force microscopy (AFM) and transmission electron microscopy (TEM) microscopic techniques, in comparison with those of blends prepared by a conventional straight mixing method. Both the tapping mode AFM phase images and TEM micrographs clearly show that reactive mixing leads to more homogeneous blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:2547–2554, 2007     

Structure and properties of dynamically cured EPDM/PP blends

The structure and properties of polyolefin blends of ethylene–propylene–diene terpolymer (EPDM) and polypropylene were studied. Blends were prepared in a laboratory internal mixer where EPDM was cured with PP under shear with dicumyl peroxide (DCP) at different shear conditions (blend–cure). Blends were also prepared for comparison from EPDM which were dynamically cured in the absence of PP and blended later (cure–blend). The effect of DCP concentration, intensity of the shear mixing, and rubber/plastic composition were studied. In blend–cure, the melt viscosity increased with increasing DCP concentration in blends of 75% EPDM and 25% PP, but it decreased with increasing DCP concentration in blends of 75% PP and 25% EPDM. In cure–blend, however, the melt viscosity increased with increasing DCP concentration for all compositions. The melt viscosity decreased with increasing intensity of the shear mixing presumably due to the formation of the smaller segregated microdomain of the crosslinked EPDM gels in both blend–cure and cure–blend materials. The crystallization rate was higher in EPDM/PP blends than in PP homopolymer. The crystallization rates for various blending conditions were also compared.     

Differential scanning calorimetric and free volume study of reactive compatibilization by EPM‐g‐MA of poly(trimethylene terephthalate)/EPDM blends

Differential scanning calorimetry (DSC) and positron annihilation lifetime measurements have been carried out to study the effect of the compatibilizer maleic anhydride grafted ethylene propylene copolymer (EPM‐g‐MA) in poly trimethylene terephthalate and ethylene propylene diene monomer (PTT/EPDM) immiscible blends. The DSC results for the blends of 50/50 and 30/70 compositions show two clear glass transition temperatures, indicating that the blends are two‐phase systems. With the addition of compatibilizer, the separation between the two glass transitions decreased, suggesting an increased interaction between the blend components with compatibilizer. At 5 wt % of compatibilizer, the separation between the T_gs reduced in both 50/50 and 30/70 blends. The positron results for the blends without compatibilizer showed an increase in relative fractional free volume, as the EPDM content in the blend is increased. This suggests the coalescence of free volume of EPDM with the free volumes of PTT due to phase separation. However, the effect of compatibilizer in the blends was clearly seen with the observed minimum in free volume parameters at 5% of the compatibilizer, further suggesting that this percent of compatibilizer seems to be the optimum value for these blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 740–747, 2006     

Swelling behavior of NR/EPDM rubber blends under compression strain

The effect of different blend compositions of natural rubber (NR)/ethylene–propylene diene monomer rubber (EPDM) on the swelling behavior of that blend in motor oil under compression strain was investigated. The compression recovery of all blend ratios investigated had positive values at low applied compression values (3%). However, at high compression values (18 and 35%), the compression recovery had negative values. The lower weight uptake of motor oil was shown by the EPDM vulcanizate, whereas the 25/75 NR/EPDM blend showed the highest compression recovery. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3052–3057, 2001     

Improved mechanical properties of NR/EPDM blends by controlling the migration of curative and filler via reactive processing technique

Simple blending of natural rubber/ethylene–propylene–diene rubber (NR/EPDM) generally results in inferior mechanical properties because of curative migration and their differences for filler affinity. In this work, the 70/30 and 50/50 NR/EPDM blends prepared by reactive processing techniques were investigated and compared with the simple, nonreactive blends. The reactive blend compounds were prepared by preheating EPDM, containing all curatives to a predetermined time related to their scorch time prior to blending with NR. For the 70/30 gum blends, four types of accelerators were studied: 2,2‐mercaptobenzothiazole (MBT), 2,2‐dithiobis‐ (benzothiazole) (MBTS), N‐cyclohexyl‐2‐benzothiazolesulfenamide (CBS), and N‐tert‐butyl‐2‐benzothiazolesulfenamide (TBBS). When compared with the simple blends, the reactive blends cured with CBS and MBTS showed a clearly improved tensile strength whereas the increase of tensile strength in the blends cured with TBBS and MBT was marginal. However, a dramatic improvement of ultimate tensile properties in the reactive 50/50 NR/EPDM blends cured with TBBS was observed when compared with the simple blend. For the N‐550‐filled blends at the blend ratios of 70/30 and 50/50, the reactive‐filled blends prepared under the optimized preheating times demonstrated superior tensile strength and elongation at break over the simple blends. The improved crosslink and/or filler distribution between the two rubber phases in the reactive blends accounts for such improvement in their mechanical properties. This is shown in the scanning electron micrographs of the tensile fractured surfaces of the reactive blends, which indicate a more homogeneous blend. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Characteristics of polynorbornene and ethylene-propylene terpolymer blends

In this study characteristics of polynorbornene (PNR) and ethylene-propylene terpolymer (EPDM) blends were examined in terms of compatibility, cocuring, and ozone resistance. For most of the blend compositions, two glass transition temperatures (T_g) at about ?30 and ?50°C were observed from differential scanning calorimetry data for both uncured and cured samples. The transitions correspond to the T_g's of the component polymers, suggesting that the blends are microheterogeneous. The two-phase blends are difficult to cocure as evidenced by the fact that tensile strengths of the blends, when plotted as a function of blend composition, deviate from the linear or additive behavior. Improved cocuring of the blends, however, can be achieved by matching the cure rates of the components. The ozone resistance of the blends containing 25 percent or more EPDM was substantially improved as compared with that of PNR. Therefore, the newly developed PNR can be used for applications requiring ozone resistance by properly blending it with EPDM.     

Flow Behavior of Polypropylene/Ethylene-Propylene Diene Terpolymer/Natural Rubber (PP/EPDM/NR) Blends by Torque Rheometer: The Effect of N,N-m-Phenylene Bismaleimide (HVA-2) Addition

Blends of polypropylene (PP)/ethylene-propylene diene terpolymer (EPDM)/natural rubber (NR) with different ratio were investigated using a Haake torque rheometer. The effect of N,N-m-phenylene bismaleimide (HVA-2) addition on the flow behavior of PP/EPDM/NR blends also was studied. The torque data was collected at different rotor speeds in the range of 30–60 rpm and different processing temperatures in the range of 170–190°C. The recorded data were interpreted in terms of apparent shear rate, apparent shear stress, and apparent viscosity. The shear stress–shear strain curve shows that all blends follow the power law where the pseudoplasticity behavior of melt viscosity increases with increasing NR content as well as addition of HVA-2. The apparent viscosity of the blends was found to increase with increasing NR content in the blend. The addition of HVA-2 increases the apparent viscosity due to the formation of cross-linking in rubber phase. However, blends with HVA-2 show lower flow activation energies than do similar blends without HVA-2. Scanning electron microscopy (SEM) shows good correlation with the flow properties of the blends.     

Effect of the addition of acrylonitrile/ethylene–propylene–diene monomer (EPDM)/styrene graft copolymer on the morphology–properties relationships in poly(styrene‐co‐acrylonitrile)/EPDM rubber blends

Blends of poly(styrene‐co‐acylonitrile) (SAN) with ethylene–propylene–diene monomer (EPDM) rubber were investigated. An improved toughness–stiffness balance of the SAN/EPDM blend was obtained when an appropriate amount of acrylonitrile–EPDM–styrene (AES) graft copolymer was added, prepared by grafting EPDM with styrene–acrylonitrile copolymer, and mixed thoroughly with both of the two components of the blend. Morphological observations indicated a finer dispersion of the EPDM particles in the SAN/EPDM/AES blends, and particle size distribution became narrower with increasing amounts of AES. Meanwhile, it was found that the SAN/EPDM blend having a ratio of 82.5/17.5 by weight was more effective in increasing the impact strength than that of the 90/10 blend. From dynamic mechanic analysis of the blends, the glass‐transition temperature of the EPDM‐rich phase increased from ?53.9 to ?46.2°C, even ?32.0°C, for the ratio of 82.5/17.5 blend of SAN/EPDM, whereas that of the SAN‐rich phase decreased from 109.2 to 108.6 and 107.5°C with the additions of 6 and 10% AES copolymer contents, respectively. It was confirmed that AES graft copolymer is an efficient compatibilizer for SAN/EPDM blend. The compatibilizer plays an important role in connecting two phases and improving the stress transfer in the blends. Certain morphological features such as thin filament connecting and even networking of the dispersed rubber phase may contribute to the overall ductility of the high impact strength of the studied blends. Moreover, its potential to induce a brittle–ductile transition of the glassy SAN matrix is considered to explain the toughening mechanism. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1685–1697, 2004     

Boiling water aging of polycarbonate and polycarbonate/acrylonitrile–butadiene–styrene resin and polycarbonate/low‐density polyester blends

The effects of boiling water on the mechanical and thermal properties and morphologies of polycarbonate (PC), PC/acrylonitrile–butadiene–styrene resin (PC/ABS), and PC/low‐density polyester (PC/LDPE) blends (compositions of PC/ABS and PC/LDPE blends were 80/20) were studied. PC and the PC/ABS blend had a transition from ductile to brittle materials after boiling water aging. The PC/LDPE blend was more resistant to boiling water aging than PC and the PC/ABS blend. The thermal properties of glass‐transition temperature (T_g) and melting temperature (T_m) in PC and the blends were measured by DSC. The T_g of PC and PC in the PC/ABS and PC/LDPE blends decreased after aging. The T_g of the ABS component in the PC/ABS blend did not change after aging. The supersaturated water in PC clustered around impurities or air bubbles leading to the formation of microcracks, which was the primary reason for the ductile–brittle transition in PC, and the microcracks could not recover after PC was treated at 160°C for 6 h. The PC/ABS blend showed slightly higher resistance to boiling water than did PC. The highest resistance to boiling water of the PC/LDPE blend may be attributed to its special structural morphology. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 589–595, 2003     

Effects of trans-polyoctylene rubber (TOR) on the properties of NR/EPDM blends

trans-Polyoctylene rubber (TOR) was melt blended with an incompatible NR/EPDM (70/30) blend. Mixing torque and temperature were reduced as TOR was added to NR/EPDM blend. The curing characteristics of the blend were affected as TOR participated in vulcanization and became a part of network. A scanning electron micrograph demonstrated that addition of TOR improved the compatibility of the blend and thereby led to a finer phase morphology. The ozone resistance of the blends was determined in terms of a critical stress–strain parameter. The critical stored energy density for ozone cracking was significantly enhanced for the TOR containing rubber blend. It was believed that the improvement in ozone resistance arised from finely dispersed ozone-resistant EPDM particles in the blend. TOR caused an improvement in dynamic properties and an increase in tensile modulus, but a decrease in tensile stress and elongation at break of the rubber blend. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 749–756, 1999     

Recycling of ethylene propylene diene monomer (EPDM) waste. III. Processability of EPDM rubber compound containing ground EPDM vulcanizates

The rheological behavior of ethylene propylene diene monomer (EPDM) compounds containing ground EPDM waste (W‐EPDM) of known composition was studied by using a Monsanto processability tester in a temperature range of 90–110°C and a shear rate range of 306.7–1533.24 s^?1. It is found that the shear viscosity decreases slightly with increasing W‐EPDM loading because of wall slip that results from the migration of lubricants from the W‐EPDM. The addition of W‐EPDM to raw EPDM results in a decreased die swell at all temperatures and shear rates. SEM photomicrographs of the EPDM extrudate surface show improved surface smoothness and reduced extrudate distortion when EPDM is blended with W‐EPDM. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2204–2215, 2003     

Compatibilization of PP/EPDM blends by grafting acrylic acid to polypropylene and epoxidizing the diene in EPDM

In this article, ethylene–propylene–diene‐rubber (EPDM) was epoxidized with an in situ formed performic acid to prepare epoxided EPDM (eEPDM). The eEPDM together with the introduction of PP‐g‐AA was used to compatibilize PP/EPDM blends in a Haake mixer. FTIR results showed that the EPDM had been epoxidized. The reaction between epoxy groups in the eEPDM and carboxylic acid groups in PP‐g‐AA had taken place, and PP‐g‐EPDM copolymers were formed in situ. Torque test results showed that the actual temperature and torque values for the compatibilized blends were higher than that of the uncompatibilized blends. Scanning electron microscopy (SEM) observation showed that the dispersed phase domain size of compatibilized blends and the uncompatibilized blends were 0.5 and 1.5 μm, respectively. The eEPDM together with the introduction of PP‐g‐AA could compatibilize PP/EPDM blends effectively. Notched Izod impact tests showed that the formation of PP‐g‐EPDM copolymer improved the impact strength and yielded a tougher PP blend. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3949–3954, 2006     

Influence of Copolymer Composition and Curing on Toughness of Isotactic Polypropene Blended Together with Metallocene‐EPDM and Ethene/Propene/Vinylcyclohexane Terpolymers

Ethene/propene terpolymers containing either 1‐vinylcylohexene‐4 (VCHen) or vinylcyclohexane (VCHan) as termonomer component were prepared using MAO‐activated rac‐Me₂Si(2‐MeBenz[e]Ind)₂ZrCl₂ (MBI). Propene content was varied between 26 and 72 wt.‐% with less than 1 mol‐% termonomer incorporation. Blends containing 85 vol.‐% isotactic polypropene (i‐PP) and 15 vol.‐% of the two EP terpolymer families were prepared by melt‐compounding in a twin‐screw kneader at 200°C to examine the role of sulfur‐mediated crosslinking of the unsaturated EPDM terpolymer phase in comparison to the corresponding blends containing non‐crosslinked saturated EP/VCHan terpolymers. The observed glass temperature (T_g) depression of the T_g of EP(D)M phases with respect to the T_g of the corresponding bulk EP(D)M was attributed to the presence of thermally induced stresses in both blend systems. Blends of i‐PP with crosslinked EPDM showed smaller T_g depression with respect to those of iPP/EPM blends containing non‐crosslinked EP and EPM dispersed phases. Morphology differences were detected for i‐PP/EPM and dynamically vulcanized i‐PP/EPDM blends by means of atomic force microscopy (AFM). The crosslinked i‐PP/EPDM blends exhibited significantly improved low temperature toughness as compared to the corresponding non‐crosslinked i‐PP/EPM blends. Curing of the EPDM elastomer phase in i‐PP/EPDM (85 vol.‐%/15 vol.‐%) blends afforded significantly improved toughness/stiffness balance and a wider toughness window with respect to the corresponding i‐PP/EPM and i‐PP/EP blends without sulfur‐cured rubber phases.     

EPDM/NR并用胶的复合交联

采用硫黄硫化体系和过氧化物（硫化剂DCP）硫化体系对EPDM／NR并用胶实施复合交联，研究并用比和复合交联体系对胶料的硫化特性、物理性能和耐热老化性能的影响。结果表明，在大部分并用比下，复合交联可以改善胶料的硫化特性；在硫化剂DCP和助交联剂TAIC的用量均为2份、EPDM／NR／ENR并用比为30／68．5／1．5时，并用胶的物理性能优良；以NR为主的并用胶在复合交联时硫化剂DCP和助交联剂TAIC的用量宜取1～2份。     

Oxidation‐grafting surface modification of waste silicone rubber composite insulator powder: Characterizations and properties of EPDM/modified waste powder composites

In order to broaden the applications of waste silicone rubber composite insulator powder (WSP), modified waste powder (WSP‐KH570) was prepared by a two‐step treatment process involving improved surface oxidation approach by using acidic H₂O₂ solution and subsequently grafting of KH570. Fourier transform infrared spectroscopy in the attenuated total reflection mode (FTIR‐ATR) analysis revealed the presence of KH570 on the powder surface. The result was confirmed by thermogravimetric analysis (TGA). Blends of ethylene propylene diene monomer (EPDM) with WSP‐KH570 were prepared. The effects of WSP‐KH570 on mechanical properties and thermal properties of the blends were investigated. The WSP‐KH570 showed an observed improvement in tensile strength and elongation at break of EPDM/WSP‐KH570 blends compared with corresponding compositions of EPDM/WSP blends. The TGA cure showed that EPDM filled with WSP‐KH570 had higher thermal stability at 210–380 °C than EPDM/WSP. Dynamic mechanical analysis indicated EPDM and WSP‐KH570 were better miscible with the blend ratio (90/10). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45438.     

PS/EPDM blends prepared by in situ polymerization of styrene

PS/EPDM blends formed by in situ polymerization of styrene in the presence of EPDM were prepared. EPDM has excellent resistance to factors such as weather, ozone and oxidation and it could be a good alternative for substituting polybutadiene‐based rubbers in PS toughening. The PS/EPDM blends present two phases, an EPDM elastomeric phase dispersed into a rigid matrix. The blends show higher thermal stability than polystyrene homopolymer due to the stabilizing effect of EPDM incorporation. The mechanical properties of in situ polymerized PS/EPDM blends with different compositions were evaluated before and after accelerated photoaging and compared with the properties of HIPS submitted to the same aging conditions. The blend containing 17 wt % of EPDM presents an increase in the impact resistance of 210% in comparison with the value of PS. Although the initial mechanical properties of HIPS are superior, a pronounced drop was observed after an exposure time. For example, after the aging period, all PS/EPDM blends showed higher strain at break than HIPS. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rheological properties and crystalline structure of the dynamically cured EPDM and PP/HDPE ternary blends

The rheological properties and crystalline structure of the polyolefin ternary blends of EPDM/polypropylene/high density polyethylene were studied. Blends were prepared in a laboratory internal mixer by two different methods. In blend–cure process, blending and curing were performed simultaneously and EPDM was cured by dicumyl peroxide (DCP) in the presence of PP/HDPE under shear. The cure–blend was to cure EPDM alone first under shear (dynamic curing) and then mix the cured EPDM with PP and HDPE. The effect of DCP concentration, intensity of the shear mixing, and the rubber/plastic composition were studied using capillary rheometer and X-ray diffractometer. The PP-rich ternary blends showed the effect of the mechanooxidative degradation of PP by shear and peroxide. The melt viscosity increased with increasing DCP concentration in blends of EPDM-rich compositions. X-ray diffraction studies revealed that the inclusion of 25 wt % of linear EPDM in the PP/HDPE mixture for the PP-rich ternary blends changed the crystal structure of polypropylene component in the ternary blends. However, the dynamic curing did not alter the crystal structure of PP or HDPE in the blends.     

Dispersive mixing efficiency of an elongational flow mixer on PP/EPDM blends: Morphological analysis and correlation with viscoelastic properties

Polypropylene and ethylene‐propylene‐diene terpolymer (PP/EPDM) blends were melt compounded in a new mixing device, designed in our laboratory under the trademark of RMX®, which predominantly generates elongational flows. Dispersion of the EPDM minor phase in PP was carried out in both RMX® and in an internal mixer (Haake Rheomix 600) at equivalent specific mixing energies and the resultant morphologies obtained by SEM were analyzed and compared. A better dispersive mixing efficiency of the RMX® mixer, i.e., lower D_n and D_v of the dispersed EPDM phase was observed. The impact of elongational flow was more pronounced for blends having a high viscosity ratio p, indicating an enhanced droplet break‐up mechanism, which was attributed to the combination of high shear rates inside the mixing element and important elongational flows in the convergent/divergent zones. The morphology of the blends was correlated with their linear viscoelastic properties by using the Palierne model. Very good agreement was found for the PP/EPDM 80/20 blends but for higher EPDM content, the Palierne model failed to describe the rheological behavior, which was attributed to percolation of the minor phase with increasing the concentration. Higher elasticity at low frequencies was observed for blends processed in the RMX®, which was attributed to a higher generated interfacial area. POLYM. ENG. SCI., 54:1444–1457, 2014. © 2013 Society of Plastics Engineers