Non‐isothermal crystallization kinetics of polyamide 1010/montmorillonite nanocomposite

The non‐isothermal crystallization kinetics of pure polyamide 1010 (PA1010) and PA1010/montmorillonite nanocomposite (PA1010/MMT) was investigated by differential scanning calorimetry (DSC) at various cooling rates. The Avrami analysis modified by Jeziorny and a new method developed by Mo can describe the non‐isothermal crystallization process of PA1010 and PA1010/MMT nanocomposite very well. The difference in the value of exponent n between PA1010 and PA1010/MMT nanocomposite suggests that the nano‐size montmorillonite layers act as nucleation agents of PA1010. The values of half‐time of crystallization and crystallization rate coefficient (CRC) show that the crystallization rate of PA1010/MMT nanocomposite is faster than that of PA1010 at a given cooling rate. Polym. Eng. Sci. 44:861–867, 2004. © 2004 Society of Plastics Engineers.     

Isothermal crystallization kinetics and melting behavior of polyamide 11/silica nanocomposites prepared by in situ melt polymerization

Polyamide 11 (PA 11)/silica nanocomposites were prepared via in situ melt polymerization by the dispersion of hydrophobic silica in 11‐aminoundecanoic acid monomer. Their isothermal crystallization process and melting behaviors were analyzed by differential scanning calorimetry. The isothermal crystallization kinetics was analyzed by the Avrami equation. The obtained data showed that the model of nucleation and growth of PA 11 was not affected after the incorporation of silica and was a mixture with two‐dimensional, circular, three‐dimensional growth with thermal nucleation. Double and single melting peaks were observed depending on the crystallization temperature. The equilibrium melting point of samples was evaluated, and the spherulites growth kinetics parameters and fold surface free energy were further calculated according to the classical theories. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of zirconium dioxide on crystallization and melting behavior of flame sprayed polyamide 1010

The crystallization and melting behavior of flame sprayed Polyamide 1010 (PA1010) containing zirconium dioxide (ZrO₂) were investigated using differential scanning calorimeter (DSC). ZrO₂ has a heterogenous nucleation effect on PA1010, leading to a moderate increase in the crystallization temperature and a decrease in the supercooling temperature. A modified Avrami theory could be successfully used to well describe the early stages of non‐isothermal crystallization of PA1010 and its composite coatings. A study of the nucleation activity, which indicated the influence of the filler on the polymer matrix, revealed that the zirconium dioxide nanoparticles had a good nucleation effect on PA1010. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers.     

Isothermal crystallization behavior of polyamide 6,6/multiwalled carbon nanotube nanocomposites

The good dispersion of functionalized multiwalled carbon nanotube (f‐MWCNT) in polyamide 6,6 (PA 6,6) matrix was prepared by solution mixing techniques. The crystalline structure and crystallization behaviors of PA 6,6 and PA 6,6/f‐MWCNT nanocomposites were studied by X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and polarized optical microscopy (POM) analysis. DSC isothermal results revealed that the overall isothermal crystallization rates of PA 6,6 increased as well as the activation energy of PA 6,6 extensively decreased by adding f‐MWCNT into PA 6,6, suggesting that the addition of f‐MWCNT probably induces the heterogeneous nucleation. The effect of f‐MWCNT on the chain arrangement for the crystallization of PA 6,6/f‐MWCNT nanocomposites was also discussed. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Nonisothermal crystallization kinetics of flame‐sprayed polyamide 1010/nano‐ZrO2 composite coatings

Polyamide1010 (PA1010) and its composite with nanometer‐sized zirconia (PA1010/nano‐ZrO₂) coatings were deposited using a flame spray process. The kinetics of nonisothermal crystallization of PA1010/nano‐ZrO₂ composite coatings was investigated by differential scanning calorimetry (DSC) at various cooling rates. Several different analysis methods were used to describe the process of nonisothermal crystallization. The results showed that the modified Avrami equation and Mo's treatment could describe the nonisothermal crystallization of the composite coatings very well. The nano‐ZrO₂ particles have a remarkable heterogeneous nucleation effect in the PA1010 matrix. The values of halftime and Z_c showed that the crystallization rate increased with increasing cooling rates for both PA1010 and PA1010/nano‐ZrO₂ composite coating, but the crystallization rate of PA1010/nano‐ZrO₂ composite coating was faster than that of PA1010 at given cooling rate. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Mechanical properties and nonisothermal crystallization kinetics of polyamide 6/functionalized TiO2 nanocomposites

Titanium dioxide (TiO₂) nanoparticles were pretreated with excessive toluene‐2,4‐diisocyanate (TDI) to synthesize TDI‐functionalized TiO₂ (TiO₂‐NCO), and then polymeric nanocomposites consisting of polyamide 6 (PA6) and functionalized‐TiO₂ nanoparticles were prepared via a melt compounding method. The interfacial interaction between TiO₂ nanoparticles and polymeric matrix has been greatly improved due to the isocyanate ( NCO) groups at the surface of the functionalized‐TiO₂ nanoparticles reacted with amino groups ( NH₂) or carboxyl ( COOH) groups of PA6 during the melt compounding and resulted in higher tensile and impact strength than that of pure PA6. The nonisothermal crystallization kinetics of PA6/functionalized TiO₂ nanocomposites was investigated by differential scanning calorimetry (DSC). The nonisothermal crystallization DSC data were analyzed by the modified‐Avrami (Jeziorny) methods. The results showed that the functionalized‐TiO₂ nanoparticles in the PA6 matrix acted as effective nucleation agents. The crystallization rate of the nanocomposites obtained was faster than that of the pure PA6. Thus, the presence of functionalized‐TiO₂ nanoparticles influenced the mechanism of nucleation and accelerated the growth of PA6 crystallites. POLYM. COMPOS., 35:294–300, 2014. © 2013 Society of Plastics Engineers     

Largely improved crystallization behavior and thermal stability of poly(L‐lactide) via the synergistic effects of graphene oxide and carbon nanotubes

Graphene oxide (GO) and carbon nanotubes (CNTs) and their compound were introduced into semicrystalline poly(l ‐lactide) (PLLA) to prepare the corresponding binary and/or ternary nanocomposites, respectively. The dispersion states of nanofillers in different nanocomposites were investigated using UV‐Vis spectroscopy, scanning electron microscopy (SEM) and rheological measurement. The results showed that when GO and CNTs were simultaneously present in the PLLA matrix, good dispersion states of both GO and CNTs could be achieved and the ternary nanocomposites exhibited percolated network structure. The effects of different nanofillers on the crystallization behavior of PLLA matrix were comparatively investigated under the different crystallization conditions including melt crystallization process (nonisothermal and isothermal crystallization from the melt) and cold crystallization (crystallization occurring from an amorphous state during the annealing process). The results showed that GO and CNTs exhibited apparent synergistic effects in improving crystallization ability and enhancing crystallinity of PLLA matrix. Study on the thermal stability of nanocomposites showed that the presence of nanofillers greatly improved the thermal stability of PLLA matrix. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40143.     

Isothermal and nonisothermal crystallization kinetics of syndiotactic polystyrene/clay nanocomposites

Differential scanning calorimeter (DSC) and X‐ray diffraction methods were used to investigate the isothermal and nonisothermal crystallization behavior and crystalline structure of syndiotactic polystyrene (sPS)/clay nanocomposites. The sPS/clay nanocomposites were prepared by mixing the sPS polymer solution with the organically modified montmorillonite. DSC isothermal results revealed that introducing 5 wt% of clay into the sPS structure causes strongly heterogeneous nucleation, inducing a change of the crystal growth process from mixed three‐dimensional and two‐dimensional crystal growth to two‐dimensional spherulitic growth. The activation energy of sPS drastically decreases with the presence of 0.5 wt% clay and then increases with increasing clay content. The result indicates that the addition of clay into sPS induces the heterogeneous nucleation (a lower ΔE) at lower clay content and then reduces the transportation ability of polymer chains during crystallization processes at higher clay content (a higher ΔE). We studied the non‐isothermal melt‐crystallization kinetics and melting behavior of sPS/clay nanocomposites at various cooling rates. The correlation among crystallization kinetics, melting behavior and crystalline structure of sPS/clay nanocomposites is discussed. Polym. Eng. Sci. 44:2288–2297, 2004. © 2004 Society of Plastics Engineers.     

火焰喷涂PA1010/nano-ZrO2复合涂层的非等温结晶动力学

利用火焰喷涂法制备了聚酰胺1010 (PA1010)/纳米氧化锆（nano-ZrO₂）复合涂层。采用示差扫描量热法（DSC）研究其非等温结晶行为，对所得的数据分别用Jeziorny法、Ozawa法和Mo法进行处理。结果表明，用Jeziorny法和Mo法处理非等温结晶过程比较理想，而Ozawa法不适用。用Jeziorny法求出的参数Z_c(结晶速率常数）和n（Avrami指数)均随降温速率的增加而增加;nano-ZrO₂的加入使复合涂层的Z_c和n略大于纯PA1010涂层;并使复合涂层结晶半衰期降低、结晶速率及结晶度增大。表明nano-ZrO₂具有明显的成核剂作用，加快PA1010的结晶速率，提高涂层的结晶度。     

Multiwall‐carbon‐nanotube‐reinforced poly(ethylene terephthalate) nanocomposites by melt compounding

Poly(ethylene terephthalate) (PET) nanocomposites reinforced with multiwall carbon nanotubes (MWCNTs) were prepared through melt compounding in a twin‐screw extruder. The presence of MWCNTs, which acted as good nucleating agents, enhanced the crystallization of PET through heterogeneous nucleation. The incorporation of a small quantity of MWCNTs improved the thermal stability of the PET/MWCNT nanocomposites. The mechanical properties of the PET/MWCNT nanocomposites increased with even a small quantity of MWCNTs. There was a significant dependence of the rheological properties of the PET/MWCNT nanocomposites on the MWCNT content. The MWCNT loading increased the shear‐thinning nature of the polymer‐nanocomposite melt. The storage modulus and loss modulus of the PET/MWCNT nanocomposites increased with increasing frequency, and this increment effect was more pronounced at lower frequencies. At higher MWCNT contents, the dominant nanotube–nanotube interactions led to the formation of interconnected or networklike structures of MWCNTs in the PET/MWCNT nanocomposites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1450–1457, 2007     

Crystal morphology and crystallization kinetics of polyamide‐11/clay nanocomposites

Polyamide‐11 (PA11)/clay nanocomposites were prepared by in situ intercalative polymerization. The crystal morphology and crystallization kinetics of these nanocomposites were investigated via polarized light microscopy (PLM), small‐angle laser scattering (SALS) and differential scanning calorimetry (DSC). PA‐11 can crystallize into well‐formed spherulites, while only very tiny crystallites were observed by PLM and SALS for the nanocomposites. Both isothermal and non‐isothermal crystallization methods were employed to investigate the crystallization kinetics by DSC. Both techniques showed an increased crystallization rate with the addition of clay. However, the Avrami exponent decreased with the addition of clay in isothermal crystallization but showed a wide range of values depending on the cooling rate in the non‐isothermal crystallization. The changes in crystal morphology and crystallization kinetics can be understood as being due to the ‘supernucleating’ effect of the nanodispersed clay layers. Copyright © 2004 Society of Chemical Industry     

Nonisothermal crystallization kinetics of polyamide 6 and ethylene‐co‐butyl acrylate blends

The nonisothermal melt‐crystallization behavior of PA6 and EBA blends at varying EBA content was investigated using differential scanning calorimetry at different scanning rates. Several macrokinetic models such as Avrami, Jeziorny, Ozawa, Liu, Ziabicki, and Tobin were applied to analyze the crystallization behavior thoroughly under nonisothermal conditions. The Avrami and Tobin model predicted that, for pure PA6 and PA6/EBA blends, simultaneous growth of all forms of crystal structures such as fibrillar, disc‐like, and spherulitic proceeds at an increasing nucleation rate. However, when applied to blends for isothermal crystallization, the Avrami model predicted that the crystallization process is diffusion‐controlled for pure PA6 and PA6/EBA blend containing higher content of EBA (50 phr), where the nylon‐6 chains were able to diffuse freely to crystallize under isothermal conditions. Liu model predicted that, at unit crystallization time, a higher cooling rate should be used to obtain a higher degree of crystallinity for both PA6 and PA6/EBA blends. The kinetic crystallizability of PA6 in the blends calculated using Ziabicki's approach varies depending upon the nucleation density and PA6‐rich regions present in the blend compositions. Nucleation activity of the blends estimated by Dobreva and Gutzowa method reveals that the EBA particles are inert at lower concentrations of EBA and do not act as nucleating agent for PA6 molecules in the blends. The activation energy of nonisothermal crystallization, calculated using Augis–Bennett, Kissinger, and Takhor methods indicated that the activation energy is slightly lower for the blends when compared to the neat PA6. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Studies on crystallization behaviors and crystal morphology of polyamide 66/clay nanocomposites

X‐ray diffraction methods, DSC thermal analysis, and polarized light microscopy (PLM) were used to investigate the structural changes of nylon 66/clay nanocomposites. PA 66/clay nanocomposites were prepared by the method of melt intercalation. The results indicate that the addition of the intercalated organo‐montmorillonite (OMMT) can induce generation of the β‐form crystal of PA 66 and substantially affect the arrangement of molecules in the α‐form crystal, although the crystallinity scarcely changes. Also, the DSC results indicate that the addition of OMMT in the PA 66 matrix leads to increases of crystallization temperatures and the full width at half maximum (FWHM) of the exothermic peaks. Moreover, the viscosity factor is the main influence on FWHM of the exothermic peaks of PA 66/clay nanocomposites. The results of nonisothermal crystallization kinetics show that OMMT has the effect of heterogeneous nucleation and leads to the decrease of the size of the spherocrystal. The heterogeneous nucleation effects of OMMTs influence the mechanism of crystallization and the growth mode of PA 66 crystals. PLM photographs verify that the size of spherocrystal is decreased and visually confirm the theory of crystallization kinetics. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 756–763, 2005     

Crystallization,morphology, and mechanical properties of poly(butylene succinate)/poly(ethylene oxide)‐polyhedral oligomeric silsesquioxane nanocomposites

The biodegradable poly(butylene succinate) (PBS)/poly(ethylene oxide)‐polyhedral oligomeric silsesquioxane (PEO‐POSS) nanocomposites were prepared by the solution blending and melt‐injection methods. The effect of PEO‐POSS on the non‐isothermal and isothermal crystallization, morphology, as well as mechanical properties of PBS was carefully investigated. The PEO‐POSS nanoparticles dispersed well in the PBS matrix, with the diameters around 30 nm. From isothermal crystallization analysis, the incorporation of PEO‐POSS enhanced the crystallization of PBS due to the heterogeneous nucleation effect while the crystal structure of PBS remained. PBS/PEO‐POSS nanocomposites showed of higher glass transition temperatures than that of neat PBS, attributing to the existence of PEO‐POSS decreasing the flexibility of PBS chains. The elongation at break of the PBS/PEO‐POSS nanocomposites reached the maximum value with PEO‐POSS content of 5 wt%. However, the elastic modulus of PBS decreased after the incorporation of PEO‐POSS. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Crystallization and morphology studies of biodegradable poly(ε‐caprolactone)/silica nanocomposites

Biodegradable poly(ε‐caprolactone) (PCL)/silica nanocomposites at various silica loadings were prepared via direct melt compounding method in this work. Scanning electron microscopy observation indicated that when the silica content was < 3 wt%, the nanoparticles dispersed evenly in the PCL matrix and exhibited only aggregates with particle size of less than 100 nm. The results of nonisothermal melt crystallization showed that the crystallization peak temperature was higher in the nanocomposites than in neat PCL; moreover, the overall crystallization rate was faster in the nanocomposites than in neat PCL during isothermal melt crystallization. Both nonisothermal and isothermal melt crystallization studies suggested that the crystallization of PCL was enhanced by the presence of silica and influenced by the silica loading. The effect of silica on the crystallization behavior was twofold: the presence of silica may provide heterogeneous nucleation sites for the PCL crystallization while the aggregates of silica may restrict crystal growth of PCL. However, the crystal structure of PCL remained almost unchanged despite the presence of silica in the nanocomposites. POLYM. COMPOS., 2013. © 2012 Society of Plastics Engineers     

Crystallization and thermal behavior of microcellular injection‐molded polyamide‐6 nanocomposites

This article presents the effects of nanoclay and supercritical nitrogen on the crystallization and thermal behavior of microcellular injection‐molded polyamide‐6 (PA6) nanocomposites with 5 and 7.5 wt% nanoclay. Differential scanning calorimetry (DSC), X‐ray diffractometry (XRD), and polarized optical microscopy (POM) were used to characterize the thermal behavior and crystalline structure. The isothermal and nonisothermal crystallization kinetics of neat resin and its corresponding nanocomposite samples were analyzed using the Avrami and Ozawa equations, respectively. The activation energies determined using the Arrhenius equation for isothermal crystallization and the Kissinger equation for nonisothermal crystallization were comparable. The specimen thickness had a significant influence on the nonisothermal crystallization especially at high scanning rates. Nanocomposites with an optimal amount of nanoclay possessed the highest crystallization rate and a higher level of nucleation activity. The nanoclay increased the magnitude of the activation energy but decreased the overall crystallinity. The dissolved SCF did not alter the crystalline structure significantly. In contrast with conventionally injection‐molded solid counterparts, microcellular neat resin parts and microcellular nanocomposite parts were found to have lower crystallinity in the core and higher crystallinity near the skin. POLYM. ENG. SCI., 46:904–918, 2006. © 2006 Society of Plastics Engineers     

Carbon nanotube surface-induced crystallization of polyethylene terephthalate (PET)

The crystallization of polyethylene terephthalate (PET) and its effect on the electrical behavior of nanocomposites of PET and carbon nanotubes (CNTs) was studied. A series of nanocomposites composed of polyethylene terephthalate/carbon nanotubes (PET/CNTs) containing 0, 1 and 2% wt/wt carbon nanotubes were prepared by melt extrusion. The morphology developed by the nanocomposites during non-isothermal crystallization at different cooling rates was evaluated using various experimental techniques. Thermal analysis showed an increase in the crystallization temperature of the nanocomposites, which was associated with the nucleation ability of the CNTs, and confined growth that resulted in a 3D-to-1D reduction in the crystallite geometry of the nanocomposites. X-ray diffraction indicated that the crystal structure of the nanocomposites was not affected by the presence of carbon nanotubes or the cooling rate. However, the crystallinity of PET and the nanocomposites increased as the cooling rate decreased. The electrical conductivity of the materials as a function of the cooling rate, at a constant CNT content, showed a marked (two orders of magnitude) increase in passing from the amorphous state to the crystalline state. The results of theoretical calculations indicated self-assembly between the surface of the nanotubes and the aromatic ring of PET; it was proposed that the stacking of aromatic rings on the surface of the nanotubes has an effect on the rearrangement of electric charge.     

离聚体对PA1010／PS共混体系相形态及结晶的影响

采用ＳＥＭ,ＤＳＣ和偏光显微镜等方法研究了磺化聚苯乙烯及其锂盐,锌盐和钠盐（ＰＳ－ＮａＳ）;四种离聚体对ＰＡ１０１０／ＰＳ共混体系相形主结晶性能的影响。结果表明,对于ＰＡ１０１０／ＰＳ（８０／２０）共混体系,四种离聚体的增容效果依次按ＰＳ－ｎａＳ〈ＰＳ－ＺｎＳ〈ＰＳ〈ＺｎＳ〈ＰＳ－ＬｉＳ〈ＰＳ－ＨＳ的顺序递增,表明离聚体的离子交联能力越弱,其增容效果越好。四种离聚体中只有ＰＳ－ＺｎＳ对ＰＡ１０１０     

Crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/clay nanocomposites

The preparation and properties of nanocomposites, consisting of a poly(3‐Hydroxybutyrate‐co‐3‐hydroxyvalerate) and an organophilic clay are described. The effect of organophilic clay on the crystallization behavior of (PHBV) was studied. A differential scanning calorimeter (DSC) was used to monitor the energy of the crystallization process from the melt. During the crystallization process from the melt, the organophilic clay led to an increase in crystallization temperature (T_c) of PHBV compared with that for plain PHBV. During isothermal crystallization, dependence of the relative degree of crystallization on time was described by the Avrami equation. The addition of organophilic clay caused an increase in the overall crystallization rate of PHBV, but did not influence the mechanism of nucleation, and growth of the PHBV crystals and the increase caused by a small quantity of clay is move effective than that large one. The equilibrium melting temperature of PHBV was determined as 186°C. Analysis of kinetic data according to nucleation theories showed that the increase in crystallization rate of PHBV in the composite is due to the decrease in surface energy of the extremity surface. The mechanical test shows that the tensile strength of hybrid increased to 35.6 MPa, which is about 32% higher than that of the original PHBV with the incorporation of 3 wt % clay, and the tensile modulus was also increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 655–661, 2004     

Effect of PMR‐POI on the melt behavior and isothermal crystallization of poly(phenylene sulfide)

The crystallization behavior of neat PPS and PPS in blends with PMR‐POI prepared by melt mixing were investigated by differential scanning calorimetry (DSC). It was found that POI was an effective nucleation agent of the crystallization for PPS. The enthalpy of crystallization of PPS in the blends increased compared with that of neat PPS. During isothermal crystallization from melt, the dependence of relative degree of crystallinity on time was described by the Avrami equation. It has been shown that the addition of POI causes an increase in the overall crystallization rate of PPS; it also changed the mechanism of nucleation of the PHB crystals from homogeneous nucleation to heterogeneous nucleation. The equilibrium melting temperature of PPS and PPS/POI blends were determined. The analysis of kinetic data according to nucleation theories shows that the increase in crystallization rate of PPS in the composite is due to the decrease in surface energy of the extremity surface. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 436–442, 2002