Structural,magnetic and photocatalytic properties of Sr2+ doped BiFeO3 nanofibres fabricated by electrospinning

Sr²⁺ doped BiFeO₃ (Bi_1-xSr_xFeO₃, 0?≤x?≤?0.35) nanofibres were fabricated by a sol-gel based electrospinning method. The as-spun BiFeO₃ (BFO) nanofibres consist of fine grained particles with high crystallinity. With Sr²⁺ doping, both the magnetic and photocatalytic properties of BFO are effectively improved. The best photocatalytic property for degradation of the methylene blue (MB) is obtained in Bi_0.75Sr_0.25FeO₃ nanofibres due to their weakest photoluminescence (PL) intensity. Meanwhile, the photocatalytic property of Bi_0.75Sr_0.25FeO₃ nanofibres is much higher than that of nanoparticles with the same constituent, which is attributed to the unique one-dimension fibrous structure benefiting the separation and decreased recombination of e^-/h⁺ pairs. This work proposes an effective approach for the degradation of organic pollutes.     

Resistive switching behavior and improved multiferroic properties of Bi0.9Er0.1Fe0.98Co0.02O3/Co1-xMnxFe2O4 bilayered thin films

Bilayered Bi_0.9Er_0.1Fe_0.98Co_0.02O₃/Co_1-xMn_xFe₂O₄ (BEFCO/CM_xFO) thin films were deposited by the sol-gel method. Structural variations between the triclinic-P1 and trigonal-R3c:H (two-phase coexistence) phases in the BEFCO layer were observed owing to the trigonal-R-3m:H phase existing in the CM_xFO layer. The oxygen vacancy concentrations of the BEFCO/CM_xFO bilayered films are reduced by Mn-doping in the bottom CFO layer. The BEFCO/CFO films showed high oxygen vacancy concentrations with a high leakage current. This induced changes of the significant potential barrier at the interface between the BEFCO and CM_xFO layers in the processes of electron capture and release. Thus, the BEFCO/CFO film exhibited obvious resistive switching (RS) effect. The high leakage current also caused a fake polarization phenomenon with a blow up of the P-E loop in the BEFCO/CFO films. However, the real and outstanding ferroelectric properties, which resulted from the fewer oxygen vacancies and the 38% triclinic-P1 structure, were obtained in the BEFCO/CM_0.3FO films (P_r~156.3?μC?cm^?2). In addition, the typical capacitance-voltage curve further confirmed its superior ferroelectric performance. The RS effect almost disappeared in the BEFCO/CM_0.3FO bilayered films. Moreover, the enhanced ferromagnetic properties (M_s~100.36?emu?cm^?3, M_r~55.38?emu?cm^?3) were obtained for the BEFCO/CM_0.1FO films, which was attributed to the magnetic properties of BEFCO (a more triclinic-P1 phase and numerous Fe²⁺ ions), in addition to the CM_xFO layer. The introduction of the doped magnetic layer into the bilayered films thus represented a highly effective method for enhancing the multiferroic properties of BFO.     

Characterisation of titania nanotubes supported gold particles for MTBE photocatalytic degradation

Au/TNT catalysts were prepared with different gold loadings by deposition – precipitation. The catalysts were characterised by techniques including XRD, HRTEM, AAS and N₂ adsorption analysis. Experimental results show that the value of surface areas and pore volumes increase with increasing Au amounts. The surface area and pore volume of catalyst with high gold loading (3.1?wt-%) are 325?m²?g^?1 and 1.34?cm^3?g^?1. The photocatalytic performance for degradation of MTBE markedly depends on gold concentration. The activity drop is attributed to the size growth and agglomeration of the gold nanoparticles. Photoactivity improvement is related to the number of nucleation centres and fine particles size. It can be concluded that there is a 10% improvement in efficiency for deposition of gold in the highest concentration compared to pure titanium nanotubes during the first 20?min of the reaction. So the photocatalytic degradation of MTBE occurs in a shorter time.     

Structural,magnetic and photocatalytic properties of Sr-doped BiFeO3 nanoparticles based on an ultrasonic irradiation assisted self-combustion method

A novel ultrasonic irradiation assisted self-combustion method was developed to prepare single-phase Bi_1−xSr_xFeO_3−δ (BSFO) nanoparticles, which were charactered by XRD, SEM, TEM and UV–vis spectra. The results show that structure, as well as magnetic and photocatalytic properties of BSFO are influenced by the particle size and the Sr²⁺ dopant content. Regarding smaller particles, even if small amount of Sr²⁺ substitution content change can result in the phase transition from the rhombohedral distorted perovskite to the cubic. The doping of heterovalent Sr²⁺ ions in BiFeO₃ (BFO) nanoparticles improves the ferromagnetic property. As ultrasonication can generate particles with larger surface area and more defections, BSFO nanoparticles exhibit efficient photocatalytic activity as a promising photocatalyst.     

Preparation and investigation of structure,magnetic and dielectric properties of (BaFe11.9Al0.1O19)1-x - (BaTiO3)x bicomponent ceramics

(BaFe_11.9Al_0.1O₁₉)_1-x - (BaTiO₃)_x with x?=?0, 0.25, 0.5, 0.75 and 1 bicomponent ceramics has been prepared from single-phase compounds of BaFe_11.9Al_0.1O₁₉ (x?=?0) (BFO) and BaTiO₃ (x?=?1) (BTO) by a standard ceramic technique. The constituent materials have been chosen considering their perspective ferrimagnetic and ferroelectric properties, respectively for BFO and BTO. Moreover, Ba-hexaferrites are reported to exhibit ferroelectricity at room temperature as well, and the combination of two ferroelectric phases is of interest. Systematic investigations of the structural, magnetic and dielectrical properties versus chemical composition (x) have been performed. The ferrimagnetic phase transition temperature is almost independent of the BTO content, which is determined by intensity of the Fe³⁺-O^2--Fe³⁺ indirect superexchange interactions in the BFO hexaferrite phase. However, the coercivity of composite samples is lower due to the contribution of the microstructure-dependent shape anisotropy to the total magnetic anisotropy energy. The permittivity vs. temperature behavior confirmed the existence of two ferroelectric phase transitions corresponding to structural phase transitions in BTO at ~ 400?K and BFO at ~ 700?K. It has been observed that the dielectrical properties of composite samples, including the temperatures of the phase transitions, critically depended on concentration x which affects the composite microstructure. This behavior has been discussed in terms of microstructure analysis and such parameters as the grain size, porosity and density.     

Synthesis and enhanced photocatalytic activity of Mn/TiO2 mesoporous materials using the impregnation method through CVC process

TiO₂ particles were prepared by chemical vapor condensation and used to synthesize MnO_x/TiO₂ mesoporous materials by impregnation. The Mn-doped TiO₂ particles were smaller (8.5?nm vs. 10.5?nm) and had greater surface areas (203.7?m²?g^?1 vs. 134.4?m²?g^?1) than undoped particles. They were also smaller and had a greater surface area than similarly doped commercial P25, indicating highly dispersed Mn species on the surfaces of the crystalline TiO₂. The resulting materials?? photocatalytic activities towards methylene blue decomposition were compared: the synthesized TiO₂ particles with MnO₂ showed higher photocatalytic activity than the similarly doped commercial P25.     

A novel “plane-line-plane” nanostructure of the sandwich-like CNTs@SnO2/Ti3C2Tx 3D nanocomposite as a promising anode for lithium-ion batteries

As one of the novel two-dimensional metal carbides, Ti₃C₂T_x has received intense attention for lithium-ion batteries. However, Ti₃C₂T_x has low intrinsic capacity due to the fact that the surface functionalization of F and OH blocks Li ion transport. Herein a novel “plane-line-plane” three-dimensional (3D) nanostructure is designed and created by introducing the carbon nanotubes (CNTs) and SnO₂ nanoparticles to Ti₃C₂T_x via a simple hydrothermal method. Due to the capacitance contribution of SnO₂ as well as the buffer role of CNTs, the as-fabricated sandwich-like CNTs@SnO₂/Ti₃C₂T_x nanocomposite shows high lithium ion storage capabilities, excellent rate capability and superior cyclic stability. The galvanostatic electrochemical measurements indicate that the nanocomposite exhibits a superior capacity of 604.1 mAh g^?1 at 0.05?A?g^?1, which is higher than that of raw Ti₃C₂T_x (404.9 mAh g^?1). Even at 3?A?g^?1, it retains a stable capacity (91.7 mAh g^?1). This capacity is almost 5.6 times higher than that of Ti₃C₂T_x (16.6 mAh g^?1) and 58 times higher than that of SnO₂/Ti₃C₂T_x (1.6 mAh g^?1). Additionally, the capacity of CNTs@SnO₂/Ti₃C₂T_x for the 50th cycle is 180.1 mAh g^?1 at 0.5?A?g^?1, also higher than that of Ti₃C₂T_x (117.2 mAh g^?1) and SnO₂/Ti₃C₂T_x (65.8 mAh g^?1), respectively.     

Effect of (Zn,Mn) co-doping on the structure and ferroelectric properties of BiFeO3 thin films

BiFe_1-2xZn_xMn_xO₃ (BFZMO, with x = 0–0.05) thin films were synthesized via sol–gel method. Effects of (Zn, Mn) co-doping on the structure, ferroelectric, dielectric, and optical properties of BiFeO₃ (BFO) films were investigated. BFZMO thin films exhibit rhombohedral structure. Scanning electron microscopy (SEM) images indicate that co-doping leads to a decrease in grain size and number of defects. Leakage current density (4.60 × 10^?6 A/cm²) of BFZMO film with x = 0.02 was found to be two orders of magnitude lower than that of pristine BFO film. Owing to decreased leakage current density, saturated P–E curves were obtained. Maximum double remnant polarization of 413.2 μC/cm² was observed for BFZMO thin film with x = 0.02, while that for the BFO film was found to be 199.68 μC/cm². The reason for improved ferroelectric properties is partial substitution of Fe ions with Zn and Mn ions, which resulted in a reduction in the effect of oxygen vacancy defects. In addition, co-doping was found to decrease optical bandgap of BFO film, opening several possible routes for novel applications of these (Zn, Mn) co-doped BFO thin films.     

Enhanced photocatalytic performance of Bi2Fe4O9/graphene via modifying graphene composite

Bi₂Fe₄O₉ (BFO) is one of the most important photocatalyst materials and its composition with graphene may leave an optimizing effect on the photocatalytic performance. In this paper, reduced graphene oxide (RGO) with various contents is selected to be composited with BFO successfully via one‐step hydrothermal method. A series of BFO‐xRGO (x=0, 1.25, 2.50, 3.75, 5, 6.25, and 7.50 wt.%) were prepared and the effects of RGO content on crystalline, light absorption, impedance, and photocatalytic degradation rate of methyl violet (MV) solution are characterized. The entire film samples exhibit enhanced photocatalytic efficiency. Especially, with 5 wt.% RGO content added, the film sample shows the best photocatalytic degradation efficiency with a MV solution degradation rate of 95%. This implies that the composition of RGO allows BFO‐based thin film as an efficient photocatalyst candidate, and as well, the BFO/RGO composite possesses the potential for better use in the related photocatalyst applications.     

Microwave absorption of M-type hexaferrite Ba1-xCaxFe12O19 (x ≤ 0.4) ceramics in 2.6–18 GHz

Ba_1-xCa_xFe₁₂O₁₉ (x?=?0.0, 0.1, 0.2, 0.3 and 0.4, BCFO) ceramics were prepared using high-temperature solid-state method and the effect of Ca²⁺ substitution was investigated. The grain size of BCFO ceramics sintered at 1250?°C for 2?h increases from 1?µm to 5?µm as Ca²⁺ added. The BCFO ceramics show a typical hard magnetic behavior with a maximum saturation magnetization (M_S) of 51.8?emu?g^?1 at x?=?0.2. The bandwidth of microwave reflection loss (RL) below ??10?dB (> 90.0% microwave absorption) is obtained in 7.60???9.8?GHz with the minimum RL ??30.8?dB at 8.5?GHz for x?=?0.2 (thickness 2.0?mm), which makes Ba_0.8Ca_0.2Fe₁₂O₁₉ ceramic a potential microwave absorption candidate.     

One-step preparation of size-defined aggregates of TiO2 nanocrystals with tuning of their phase and composition

One-step route based on the thermal decomposition of the double salt (NH₄)₂TiO(SO₄)₂ (ammonium titanyl sulfate, ATS) is presented to prepare size-defined aggregates of Ti-based nanoparticles with structural hierarchy. The component of Ti-based networks is tunable from anatase/rutile TiO₂, nitrogen-doped TiO₂, TiN_xO_1−x, to TiN depending on the atmospheres and reaction temperatures. The as-prepared Ti-based powders were characterized by X-ray diffraction analysis (XRD), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectra (DRS), and BET surface area techniques. It is found that TiO₂ in the predominant rutile phase could be achieved by the thermal decomposition of ATS in flowing Ar gas. Furthermore, the nitrogen-doped TiO₂, TiN_xO_1−x solid solution and TiN were prepared by the thermal decomposition of ATS in flowing NH₃ gas by varying the temperatures. The network of anatase TiO₂ with a specific surface area up to 64 m² g⁻¹ contains large mesopores with a mean diameter of ca. 15 nm, and the large pore size allows more accessible surface and interface available for the photocatalytic degradation of large-molecule dyes. The photocatalytic activity of the prepared TiO₂ and nitrogen-doped TiO₂ under UV–vis light irradiation is compared to Degussa P-25 using the photocatalytic degradation of methylene blue (MB) as a model reaction. The anatase TiO₂ nanoparticles derived from one-step route show the highly efficient photocatalytic activity for the degradation of MB in comparison with Degussa P-25. The presence of large-sized rutile in the TiO₂ powder decreases the specific surface area and thus the powder exhibits a lower photocatalytic activity.     

Effect of dopant on ferroelectric,dielectric and photocatalytic properties of Co–La-doped dysprosium chromite prepared via microemulsion route

In the current study, pristine and a series of La and Co-doped dysprosium chromite (Dy_1-yLa_yCr_1-xCo_xO₃) nanoparticles have been fabricated via a facile microemulsion technique. The influence of doping was evaluated based on structural, ferroelectric, dielectric, and photocatalytic properties. The prepared nanoparticles were characterized by XRD, SEM, Raman, and UV–Vis techniques. XRD patterns confirm the synthesis of a monophase orthorhombic structure with space group Pbnm with an average crystalline size in the 18–37 nm range. The saturation polarization (Ps), remanence (Pr), and coercivity (Hc) were determined using a hysteresis loop, and it was observed that by increasing the concentration of dopants, the value of Ps and Pr were improved. According to the PL spectra, highly substituted materials had a low recombination rate and higher charge separation (e^? - h⁺), which was ultimately accountable for higher photocatalytic activity. The dielectric loss decreases with frequency and dopant concentration. The photocatalytic activity of Dy_1-yLa_yCr_1-xCo_xO₃ was investigated against Crystal Violet (CV) dye under sunlight irradiation. The Dy_1-yLa_yCr_1-xCo_xO₃ furnished a 70% dye degradation in 90 min, which is attributed to the tunned bandgap and efficient electron-hole pair separation and the photocatalytic activity under visible light making Dy_1-yLa_yCr_1-xCo_xO₃ a promising photocatalyst for dye removal from wastewater.     

Water purification using a BiVO4/graphene oxide multifunctional hydrogel based on interfacial adsorption-enrichment and photocatalytic antibacterial activity

Photocatalytic degradation by visible light-driven generation of reactive oxygen species shows great promise for purification of environmental water. However, such degradation is limited by the low separation efficiency of photogenerated carriers and the poor adsorption capacity of the photocatalyst itself. To solve these problems, we successfully constructed and prepared a composite hydrogel (BV-GH) combining a three-dimensional network structure composed of graphene oxide and BiVO₄ to achieve the synergistic effects of adsorption enrichment and photocatalytic degradation. The results show that the amount of methylene blue and methyl orange adsorbed by BV-GH is 258.78 mg g^?1 and 217.16 mg g^?1, respectively, which is much higher than that obtained for pure BiVO₄. Due to the synergistic effect of adsorption enrichment and photocatalytic degradation, the degradation rate of the dye by BV-GH reaches 94.18% in 60 min, which is 6.98 times higher than that obtained for pure BiVO₄. Electron spin-resonance (ESR) experiments confirm that the main factor affecting the dye degradation by BV-GH is the ability to produce more ·OH and ·O₂^?, which is an important reason for the excellent antibacterial performance of BV-GH against E. coli. This work can provide further inspiration for photocatalytic technology in water purification.     

Photocatalytic removal of NOx over immobilized BiFeO<Subscript>3</Subscript> nanoparticles and effect of operational parameters

Perovskite type BiFeO₃ (BFO) was synthesized by sol-gel auto-combustion method. Synthesized BFO was immobilized on the micro slides glass plates by sol-gel dip-coating method. The sample was characterized by XRD, FESEM, UV-Vis DRS, and BET techniques. The XRD pattern confirmed the perovskite structure, and from the Debye-Scherrer equation the average crystalline size was calculated as 19 nm. The FE-SEM images of prepared BFO showed porous structure with low agglomeration. The band gap energy was calculated about 2.13 eV, and the specific surface area (SSA) of prepared BFO nanostructure was obtained 55.1m² g^?1. The photocatalytic activity of prepared pure and immobilized BFO was investigated in the removal of NOx under UV irradiation, in the batch photoreactor. The effects of operational parameters such as initial concentration of NOx, light intensity and amount of coated photocatalyst, under identical conditions, were investigated. The results showed that the highest conversion of NOx was obtained as 35.83% in the 5 ppm of NOx with 1.2 g immobilized BFO and under 15 W illumination lamp.     

Electrical and nonlinear current-voltage characteristics of La-doped BiFeO3 ceramics

Multiferroic Bi_1-xLa_xFeO₃(x=0, 0.05, 0.1, 0.2, and 0.3) ceramics with particle sizes of ~67–19 nm were prepared by a simple co-precipitation method. The effects of La dopant on the microstructure, giant dielectric response, and electrical properties were investigated. The grain size of Bi_1-xLa_xFeO₃ ceramics significantly decreased with increasing La doping ions. The Bi_0.95La_0.05FeO₃ ceramic exhibited the highest leakage current density value. Interestingly, it strongly decreased as the concentration of La increased. The nonlinear coefficient of La doped BFO slightly decreased with increasing La. This shows a space-charge-limited conduction mechanism, which is involved in low electric field regions for all samples investigated. La substitution significantly enhanced the breakdown field. It was found that the potential barrier height at the grain boundary was slightly reduced from 0.3 to 0.16 eV by substitution of La ions. Using impedance spectroscopy analysis, except for the Bi_0.7La_0.3FeO₃ ceramic, the grain boundary resistance at room temperature was affected by dc bias, whereas the grain resistance of all samples was independent of dc bias. This result was well consistent with the variation in low-frequency dielectric constant and loss tangent value due to the effect of dc bias. These results were closely related to the existence of the interfacial polarization at the grain boundary.     

Effect of Nb substitution on magnetic,ferroelectric and photocatalytic properties of Bi0.95Sm0.05Fe1-xNbxO3 (0 ≤ x ≤ 0.1) nanoparticles

The single phase Bi_0.95Sm_0.05Fe_1-xNb_xO₃ (0 ≤ x ≤ 0.1) nanoparticles were synthesized by the sol-gel route, and the effect of Nb substitution on their magnetic, ferroelectric and photocatalytic properties were studied. X-ray diffractometry confirms a phase transformation from rhombohedral to orthorhombic with an increase in Nb substitution. The grain size decreases significantly, and the morphology of grains becomes homogeneous with the increase of Nb concentration. The maximum remnant magnetization (0.014 emu/g), coercivity (565 Oe) and polarization (0.592 μC/cm²) are observed in Bi_0.95Sm_0.05Fe_0.9Nb_0.1O₃. It has been observed that the energy band gap has been slightly reduced from 2.14 to 2.03 eV with Nb substitution, indicating an improvement of photocatalytic activity. The methylene blue degradation is used to represent the photocatalytic ability of Bi_0.95Sm_0.05Fe_1-xNb_xO₃ nanoparticles. The highest degradation efficiency (~74%) of methylene blue is obtained in Bi_0.95Sm_0.05Fe_0.93Nb_0.07O₃, which is much higher than that of Bi_0.95Sm_0.05FeO₃ (~51%) and can be attributed to the optimum particle size and the smallest energy band gap.     

In situ synthesis of monolithic molecularly imprinted stationary phases for liquid chromatographic enantioseparation of dibenzoyl tartaric acid enantiomers

A monolithic molecularly imprinted polymer (monolithic MIP) for dibenzoyl-D-tartaric acid (D-DBTA) was prepared in a stainless-steel chromatographic column tube (50?mm?×?4.6?mm I.D.) as HPLC stationary phase through in situ polymerization. By optimizing polymeric and chromatographic conditions, the chiral separation of DBTA enantiomers was successfully achieved in the obtained MIP in less than 25?min with a resolution Rs?=?1.25, whereas no enantioseparation effect was found on the monolithic non-imprinted polymer (NIP). Thermodynamic data of the enantioseparation were calculated. The results revealed that two different thermodynamic processes existed within the temperature range investigated, moreover, just at the transition temperature (50?°C) of the two processes, separation factor ?? reached its maximum. Scathcard analysis indicated that only one class of binding sites existed in the obtained MIP, with its K _d and Q _max estimated to be 5.457?×?10^?4?mol?L^?1 and 229.6???mol?g^?1, respectively. Nitrogen adsorption experiment proved that the prepared MIP had a large specific surface area of 105?m²?g^?1. Scanning electron microscopy showed that large flow-through pores were present in the prepared monolith. As a consequence, the column backpressure was only 1.2?MPa with acetonitrile as mobile phase at a flow rate of 1.0?mL?min^?1.     

Microstructures,magnetic, and dielectric properties of Ba-doped BiFeO3 nanoparticles synthesized via molten salt route

As the paradigm of magnetoelectric multiferroic materials, BiFeO₃ (BFO) has potential applications in spintronics, memory devices, sensors, and actuators. However, its large leakage current and small magnetism at room temperature restrict its practical applications. It is demonstrated that the substitutions of Bi by alkali earth elements at A-site of BFO can significantly reduce the leakage current and enhance the remanent magnetization of BFO. In this work, Ba-doped BFO nanoparticles Bi_1-xBa_xFeO₃ (x = 0, 0.05, 0.10, 0.15 and 0.20) were synthesized via molten salt route. X-ray diffraction patterns revealed that with increasing the Ba-doped content the formation of the impurity phase was depressed and the rhombohedral distortions of these nanoparticles were suppressed, as confirmed by Raman spectra. X-ray photoelectron spectroscopy measurements reveal that the Fe element in the nanoparticles exists in the dual valence states of Fe³⁺ and Fe²⁺, and two kinds of oxygen atoms (lattice oxygen atoms and the adsorbed oxygen atoms) exist in the nanoparticles. With increasing the Ba-doped content, the content ratios of Fe³⁺ to Fe²⁺ ions were generally increased, whereas the oxygen vacancy concentrations were decreased. The average particle sizes of the Ba-doped BFO nanoparticles were decreased as compared with that of nondoped BFO nanoparticles. In contrast, the room temperature magnetization of the Ba-doped BFO nanoparticles was greatly enhanced by Ba-substitution, as confirmed by the M-H loops. At room temperature, the remanent magnetization and coercive field of the Bi_0.8Ba_0.2FeO₃ nanoparticles were 0.51 emu/g and 1130 Oe, respectively. Furthermore, the leakage current density was reduced by one order of magnitude at x = 0.2 and the dielectric properties are also improved by Ba-substitution. The improvements on the remanent magnetization, leakage current density as well as dielectric properties of the Ba-doped BFO nanoparticles make them promising candidates for spintronics and dielectric energy storages.     

Colossal permittivity and dielectric relaxations in Tl + Nb co-doped TiO2 ceramics

A series of Tl?+?Nb co-doped TiO₂ ceramics ((Tl_0.5Nb_0.5)_x%Ti_1-x%O₂ 0.5?≤?x?≤?10.0) were prepared by a solid-state reaction method under N₂ atmosphere. The evolution of their microstructures, and dielectric properties were systematically studied. The co-doped ceramics exhibited a tetragonal rutile structure wherein the Nb and Tl elements were homogeneously distributed. The cell volumes, grain size, and permittivity increased with doping x, whereas the impedance values of the grain and grain boundary decreased with an increasing x. The optimum dielectric performance (ε_r >?10⁴, tanδ?<?0.05) in the range of 10–10⁶ Hz was obtained for x?=?1.5 with a corresponding grain boundary active energy of 0.86?eV. Four types of dielectric relaxation were observed at different temperature ranges: 10–30?K, 30–200?K, 200–350?K and 350–475?K; those dielectric relaxtions were respectively caused by electron-pinned defect-dipoles, electron hopping, oxygen vacancy hopping, and Maxwell–Wagner polarization. The colossal permittivity is primarily a result of the electron-pinned defect-dipole polarization.     

Photocatalytic degradation of imidacloprid pesticide in aqueous solution by TiO2 nanoparticles immobilized on the glass plate

The purpose of this study is to appraise the photocatalytic degradation of imidacloprid pesticide in an aqueous solution. To this end, imidacloprid was degraded using TiO₂ nanoparticles immobilized on a glass plate under UV light illumination. The effects of operational parameters (initial concentration of imidacloprid, pH, and light intensity) on the activity of TiO₂ nanophotocatalyst and the kinetics of the reaction were investigated. The results indicated that TiO₂ had impressive photocatalytic proficiency in the presence of UV-C light irradiation for the removal of imidacloprid from the aqueous solution. The highest efficiency for the removal of imidacloprid (R%?=?90.24) was obtained in the initial concentration of 20?mg?L^?1 imidacloprid, pH?=?5, and light intensity of 17?W?m^?2 after 180?min. The results of the mineralization studies represented a subtractive trend of total organic carbon (TOC) and an increase in the mineralization products during the reaction time.