CO oxidation over promoted Pt catalysts

A study of CO oxidation by O₂ over Pt catalysts, promoted by MnO_x and CoO_x, is described. The activities of Pt/SiO₂, Pt/MnO_x/SiO₂ and Pt/CoO_x/SiO₂ are compared with commercial Pt/Al₂O₃, Pt/Rh/Al₂O₃ and Pt/CeO_x/Al₂O₃ catalysts. Since these catalysts differ in dispersion and weight loading of platinum, the turnover frequencies are also compared. The following order in activity in CO oxidation after a reductive pretreatment is found: Pt/CoO_x/SiO₂ > Pt/MnO_x/SiO₂, Pt/CeO_x/Al₂O₃ > Pt/Al₂O₃, Pt/Rh/Al₂O₃, Pt/SiO₂. Over Pt/CoO_x/SiO₂ CO is already oxidised at room temperature. Possible models to account for the high activity of Pt/CoO_x/SiO₂ in the CO/O₂ reaction are presented and discussed. Partially reduced metal oxides are necessary to increase the activity of the Pt/CoO_x/SiO₂, Pt/MnO_x/SiO₂ or Pt/CeO_x/Al₂O₃ catalysts. It was shown that mild ageing treatments did not affect the activity of the Pt/CoO_x/SiO₂ catalyst in CO oxidation.     

Conversion from β-Ce2O3·11Al2O3 to α-Al2O3 in Tetragonal ZrO2 Matrix

Composites of β-Ce₂O₃·11Al₂O₃ and tetragonal ZrO₂ were fabricated by a reductive atmosphere sintering of mixed powders of CeO₂, ZrO₂ (2 mol% Y₂O₃), and Al₂O₃. The composites had microstructures composed of elongated grains of β-Ce₂O₃·11Al₂O₃ in a Y-TZP matrix. The β-Ce₂O₃·11Al₂O₃ decomposed to α-Al₂O₃ and CeO₂ by annealing at 1500°C for 1 h in oxygen. The elongated single grain of β-Ce₂O₃·11Al₂O₃ divided into several grains of α-Al₂O₃ and ZrO₂ doped with Y₂O₃ and CeO₂. High-temperature bending strength of the oxygen-annealed α-Al₂O₃ composite was comparable to the β-Ce₂O₃·11Al₂O₃ composite before annealing.     

Crystal Structure and Microwave dielectric Properties of Ba(Zn1/3Ta2/3)O3–(Sr,Ba)(Ga1/2Ta1/2)O3 Ceramics

The microwave dielectric properties and crystal structure of Ba(Zn_1/3Ta_2/3)O₃– (Sr,Ba)(Ga_1/2Ta_1/2)O₃ ceramics were investigated in the present study. The Q value of Ba(Zn_1/3Ta_2/3)O₃ was improved by adding 5 mol% Sr(Ga_1/2Ta_1/2)O₃. The maximum Q value of Q × f = 162000 GHz was obtained at 0.95Ba(Zn_1/3Ta_2/3)O₃. 0.05Sr(Ga_1/2Ta_1/2)O₃. For this composition, a lattice super structure caused by hexagonal ordering was observed. A further improvement in the Q value was attained when some Sr was replaced with Ba, and 0.95Ba(Zn_1/3Ta_2/3)O₃· 0.05(Sr_0.25Ba_0.75)(Ga_1/2Ta_1/2)O₃ exhibited a maximum Q value such that Q × f = 210000 GHz. Despite the increased Q value with the replacement of Sr by Ba, the c/a value, which indicates the degree of lattice distortion, remained constant near 3/2. The Q value thus improved without lattice distortion in the system Ba(Zn_1/3Ta_2/3)O₃-(Sr,Ba)(Ga_1/2Ta_1/2)O₃, whereas the improvement of Q value increased with lattice distortion in the solid solution system with Ba(Zn_1/3Ta_2/3)O₃ as an end member.     

Upconversion Luminescence in Er3+ Doped and Yb3+/Er3+ Codoped Yttria Nanocrystalline Powders

Y_1.9Er_0.1O₃ and Y_1.7Yb_0.2Er_0.1O₃ nanocrystalline powders were prepared via a reverse-strike coprecipitation method using nitrates and ammonia as raw materials. The obtained powders were of cubic-phase structure of Y₂O₃ and the particle size was in the range of ∼60–80 nm. Strong red (⁴F_9/2–⁴I_15/2) and green (²H_11/2/⁴S_3/2–⁴I_15/2) upconversion luminescence were observed in all the samples when excited with a 980-nm continuous wave diode laser. The possible upconversion mechanisms in Y_1.9Er_0.1O₃ and Y_1.7Yb_0.2Er_0.1O₃ were discussed. Power studies indicated that two-photon processes are responsible for the green and red upconversion luminescence in these systems. The codoping of Yb³⁺ greatly enhanced the red (⁴F_9/2–⁴I_15/2) upconversion emission.     

Activity–Composition Relations in FeCr2O4–FeAl2O4 and MnCr2O4–MnAl2O4 Solid Solutions at 1500° and 1600°C

Activity–composition relations of FeCr₂O₄–FeAl₂O₄ and MnCr₂O₄–MnAl₂O₄ solid solutions were derived from activity–composition relations of Cr₂O₃–Al₂O₃ solid solutions and directions of conjugation lines between coexisting spinel and sesquioxide phases in the systems FeO–Cr₂O₃–Al₂O₃ and MnO–Cr₂O₃–Al₂O₃. Moderate positive deviations from ideality were observed.     

Pore Structure Evolution of Lanthana–Alumina Systems Prepared through Coprecipitation

Pure Al₂O₃ and different compositions of La₂O₃–Al₂O₃ samples have been prepared through coprecipitation. Even after heating at 1300°C, the compositions La₂O₃·11Al₂O₃ and La₂O₃·13Al₂O₃ had higher surface area compared to the pure Al₂O₃ and the La₂O₃·Al₂O₃ composition. Ethanol washing is an effective way for improving the textural stability of pure Al₂O₃ and La₂O₃–Al₂O₃ samples. The effect of steam on the thermal stability of La₂O₃·11Al₂O₃ has also been studied. La₂O₃·11Al₂O₃ sample is found to be stable in steam.     

Synthesis of V2O3 Powder by Evaporative Decomposition of Solutions and H2 Reduction

The evaporative decomposition of solutions method was used to form V₂O₅. Spraying above the congruent melting temperature of V₂O₅ (690°C) resulted in dense spherical particles with a smooth surface. Spraying below the V₂O₅ melting temperature yielded porous V₂O₅ powder with a rough surface. Reduction of the V₂O₅ to V₂O₃ was done in a H₂ atmosphere. Spherical V₂O₃ powder was attained when the reduction temperature was low enough to reduce the V₂O₅ surface before partial sintering (necking) between V₂O₅ particles occurred. The resulting V₂O₃ particle size was smaller than the precursor V₂O₅ powder as expected by the differences in densities between V₂O₅ ( p = 3.36 g/cm³) and V₂O₃ ( p = 4.87 g/cm³).     

Effect of the addition of transition metals to Pt/Ba/Al2O3 catalyst on the NOx storage-reduction catalysis under oxidizing conditions in the presence of SO2

The NO_x storage-reduction catalysis under oxidizing conditions in the presence of SO₂ has been investigated on Pt/Ba/Fe/Al₂O₃, Pt/Ba/Co/Al₂O₃, Pt/Ba/Ni/Al₂O₃, and Pt/Ba/Cu/Al₂O₃ catalysts compared with Pt/Ba/Al₂O₃, Pt/Fe/Al₂O₃, Pt/Co/Al₂O₃, Pt/Ni/Al₂O₃, Pt/Cu/Al₂O₃ and Pt/Al₂O₃ catalysts. The NO_x purification activity of Pt/Ba/Fe/Al₂O₃ catalyst was the highest of all the catalysts investigated in this paper after an aging treatment. That of the aged Pt/Ba/Co/Al₂O₃ and Pt/Ba/Ni/Al₂O₃ catalysts was essentially the same as that of the aged Pt/Ba/Al₂O₃ catalyst, while that of the aged Pt/Ba/Cu/Al₂O₃ and Pt/Cu/Al₂O₃ catalysts was substantially lower than the others.

The Fe-compound on the aged Pt/Ba/Fe/Al₂O₃ catalyst has played a role in decreasing the sulfur content on the catalyst after exposure to simulated reducing gas compared with the Pt/Ba/Al₂O₃ catalyst without the Fe-compound. XRD and EDX show that the Fe-compound inhibits the growth in the size of BaSO₄ particles formed on the Pt/Ba/Fe/Al₂O₃ catalyst under oxidizing conditions in the presence of SO₂ and promotes the decomposition of BaSO₄ and desorption of the sulfur compound under reducing conditions.     

Effects of B2O3 on the Phase Stability of Ba2Ti9O20 Microwave Ceramic

Preparation of dense and phase-pure Ba₂Ti₉O₂₀ is generally difficult using solid-state reaction, since there are several thermodynamically stable compounds in the vicinity of the desired composition and a curvature of Ba₂Ti₉O₂₀ equilibrium phase boundary in the BaO–TiO₂ system at high temperatures. In this study, the effects of B₂O₃ on the densification, microstructural evolution, and phase stability of Ba₂Ti₉O₂₀ were investigated. It was found that the densification of Ba₂Ti₉O₂₀ sintered with B₂O₃ was promoted by the transient liquid phase formed at 840°C. At sintering temperatures higher than 1100°C, the solid-state sintering became dominant because of the evaporation of B₂O₃. With the addition of 5 wt% B₂O₃, the ceramic yielded a pure Ba₂Ti₉O₂₀ phase at sintering temperatures as low as 900°C, without any solid solution additive such as SnO₂ or ZrO₂. The facilities of B₂O₃ addition to the stability of Ba₂Ti₉O₂₀ are apparently due to the eutectic liquid phase which accelerates the migration of reactant species.     

Stability of YBa2Cu3O7-x in Molten Chloride Salts

The decomposition products of YBa₂Cu₃O_7-x depend on the composition of the molten chloride salt for exposure at 1173 K in air. The presence of dichloride salts such as CuCl₂, CaCl₂, or MgCl₂ promote formation of CuO, Cu₂Y₂O₅, and loss of barium to the chloride salt as BaCl₂. Salts based on BaCl₂ or containing LiCl result in YBa₂Cu₃O_7-x decomposition products of Y₂BaCuO₅, CuO, and BaCl₂. High barium activity in the salt supports formation of the Y₂BaCuO₅ phase and reaction of CO₂ with the salt producing BaCO₃. Decomposition is most sluggish in binary NaCl-KCl salts where minimal amounts of reaction or decomposition products are observed.     

Superconducting Properties of Barium-Doped (Bi,Pb)2Sr2Ca2Cu3Ox Glass-Ceramics

The Ba-doped superconducting (Bi,Pb)₂Sr_{2- x} Ba _x Ca₂Cu₃O _y and (Bi,Pb)₂Sr₂Ca_{2- x} Ba _x Cu₃O _y (0 ≦ x ≦ 1.0) were prepared by using a melt-quenching method, and the effect of Ba additions on the glass-forming ability and the crystalline phase was examined. The glass-forming ability was not improved by substitution of Ba for Sr or Ca, and particularly BaPbO₃ as well as CaO was observed in the melt-quenched sample of (Bi,Pb)₂SrBaCa₂Cu₃O _y . BaPbO₃ crystals were precipitated in all glass-ceramics with Ba substituted for Sr or Ca. The partial substitution of Ba substituted for Sr was effective for the formation of the high- T _c phase, and (Bi,Pb)₂Sr_1.4Ba_0.6Ca₂Cu₃O _y glass-ceramics obtained by annealing at 830°C for 100 h exhibited superconductivity with a T _c of 103 K, although BaPbO₃ and the low- T _c phase were still largely present.     

Microwave Dielectric Properties of Low-Fired Ba5Nb4O15

The effect of B₂O₃ on the sintering temperature and microwave dielectric properties of Ba₅Nb₄O₁₅ has been investigated using X-ray powder diffraction, scanning electron microscopy, and a network analyzer. Interactions between Ba₅Nb₄O₁₅ and B₂O₃ led to formation of second phases, BaNb₂O₆ and BaB₂O₄. The addition of B₂O₃ to Ba₅Nb₄O₁₅ resulted in lowering the sintering temperature from 1400° to 925°C. Low-fired Ba₅Nb₄O₁₅ could be interpreted by measuring changes in the quality factor ( Q × f ), the relative dielectric constant (ɛ_r), and the temperature coefficient of resonant frequency (τ_f) as a function of B₂O₃ additions. More importantly, the formation of BaNb₂O₆ provided temperature compensation. The microwave dielectric properties of low-fired Ba₅Nb₄O₁₅ had good dielectric properties: Q × f = 18700 GHz, ɛ_r= 39, and τ_f= 0 ppm/°C.     

Incorporation of Aliovalent Dopants into the Bismuth-Layered Perovskite-Like Structure of BaBi4Ti4O15

The solid solubility of the aliovalent dopants Fe³⁺ and Nb⁵⁺ in the BaBi₄Ti₄O₁₅ compound, a member of the family of Aurivillius bismuth-based layer-structure perovskites, has been studied using quantitative wavelength-dispersive spectroscopic microanalysis (SEM/EPMA) in combination with X-ray powder diffractometry (XRPD). The samples with nominal (starting) compositions corresponding to the chemical formulas BaBi₄Ti_{4–4 X} Fe_{4 X} O₁₅ and BaBi₄Ti_{4–4 X} Nb_{4 X} O₁₅ were prepared by hot forging a mixture of BaTiO₃ and Bi₄Ti₃O₁₂ with additions of Fe₂O₃ or Nb₂O₅ followed by a long annealing at 1100°C. The study showed that an excess charge introduced into the structure by the substitution of Ti⁴⁺ ions with aliovalent dopants was preferentially compensated by a change in the ratio of Ba²⁺ to Bi³⁺ ions in the host structure according to the general formulas of the solid solutions Ba_{1–4 X} Bi_{4+4 X} Ti_{4–4 X} Fe^'_{4 X} O₁₅ and Ba_{1+4 X} Bi_{4–4 X} Ti_{4–4 X} Nb^·_{4 X} O₁₅.     

Energy Transfer and Population Inversion in Heavy Metal Oxide Glasses Doped with Tm3+ and Tb3+

Emission properties and energy transfer of PbO–Bi₂O₃–Ga₂O₃–GeO₂ glasses codoped with Tm³⁺ and Tb³⁺ ions were investigated. The 1.48-μm emission due to the Tm³⁺:³H₄→³F₄ transition can be used to amplify the S-band (1460–1530-nm) signal light. With Tb³⁺ addition, the lifetime and emission intensity of the Tm³⁺:³F₄ level decreased sharply via the Tm³⁺:³F₄→Tb³⁺:⁷F_0,1,2 energy transfer. Population densities of the ³F₄ and ³H₄ levels in Tm³⁺ calculated from rate equations clearly verified that population inversion in Tm³⁺ ions became possible with as little as 0.1 mol% of Tb³⁺ addition.     

Water-Based Gelcasting of Surface-Coated Silicon Nitride Powder

A layer of Y₂O₃–Al₂O₃, used as a sintering aid, was coated onto the surface of Si₃N₄ particles by the precipitation of inorganic salts from a water-based solution containing Al(NO₃)₃, Y(NO₃)₃, and urea. The electrokinetic and colloidal characteristics of the Si₃N₄ powder were changed significantly by the coating layer. As a result, dispersion of the Y₂O₃–Al₂O₃-coated Si₃N₄ powder was significantly greater than that of the original powder. Furthermore, the Y₂O₃–Al₂O₃ coating layer prevented the hydrogen-gas-discharging problem that occurred during gelcasting of the original Si₃N₄ powder because of reaction between the uncoated powder and the basic aqueous solution in suspension. Surface coating, as well as the gelcasting process, significantly improved the microstructure, room-temperature bending strength, and Weibull modulus of the resulting ceramic bodies.     

Reactions and Microstructure Development in Mullite Fibers

Microstructural and compositional changes during heat treatment of sol–gel-derived mullite fibers with additions of 2 wt% B₂O₃, 2 wt% P₂O₅, 2 wt% Cr₂O₃, and (1 wt% P₂O₅+ 1 wt% Cr₂O₃) were compared with those of undoped mullite fibers. For all compositions the sequence of phase development was the crystallization of a spinel phase (†-Al₂O₃ or Al–Si spinel) from amorphous material, followed by the formation of mullite at higher temperatures. Differential thermal analysis showed that additions of B₂O₃ and P₂O₅ increased the temperature of spinel formation and that B₂O₃ significantly decreased the temperature of mullite formation. After 1 h at 1200°C, the size of mullite grains in fibers that contained B₂O₃ was less than 1000 Å the grains in fibers of other compositions were 6000 to 12000 Å. After 60 h at 1400°C, fibers modified with B₂O₃ had a grain size less than 2000 to 3000 Å the grains in fibers of other compositions were 6000 to 12000 Å. B₂O₃ was the most volatile additive.     

Pyroxene-Type (K,Na,Li)VO3 Solid Solutions

Phase relations in the system were studied between 600° and 350°C. All three end members have the pyroxene-type structure. Both LiVO₃ and NaVO₃ are monoclinic, whereas KVO₃ takes the orthorhombic symmetry. At 360°C, the join LiVO₃–NaVO₃ is characterized by two series of pyroxene-type solid solutions: NaVO₃–(Na_0.44Li_0.56)VO₃ and LiVO₃-(Na_0.16Li_0.84)-VO₃. (K_0.5Na_0.5)VO₃ and (K_0.5Li_0.5)VO₃ are two other stable phases at 360°C. The pyroxene-type (K_0.5Na_0.5)VO₃ has a range of solid solution from (K_0.6Na_0.4)VO₃ to (K_0.4Na_0.6)VO₃ along the join and extends into the ternary field with a maximum of 13 mol% LiVO₃. (K_0.5Li_0.5)VO₃ has no detectable range of solid solution, and its X-ray powder diffraction data cannot be indexed based upon either the monoclinic or the orthorhombic unit cell.     

125Te, 27Al, and 71Ga NMR Study of M2O3–TeO2 (M = Al and Ga) Glasses

The structures of M₂O₃–TeO₂ (M = Al and Ga) glasses have been investigated by means of ¹²⁵Te, ²⁷Al, and ⁷¹Ga NMR spectroscopies. The structural units of respective cations in M₂O₃–TeO₂ glasses were quantitatively analyzed. The fractions of TeO₄ trigonal bipyramid, AlO₆ and GaO₆ octahedra decreased and those of TeO₃ trigonal pyramid, AlO₄, AlO₅, and GaO₄ polyhedra increased with increasing M₂O₃ content. Based on the local structures around Te, Al, and Ga atoms, the structure models of M₂O₃–TeO₂ glasses were proposed.     

LaMn1-x-yFexCoyO3-δ钙钛矿载氧体用于化学链部分氧化

采用溶胶-凝胶法制备了B位Fe和Co共取代的LaMn_1-x-yFe_xCo_yO_3-δ钙钛矿型复合氧化物，并用于化学链甲烷部分氧化制合成气。X射线衍射（XRD）结果表明Fe和Co均进入了LaMnO₃的晶格形成钙钛矿晶相，活性和稳定性测试表明LaMn_1/3Fe_1/3Co_1/3O_3-δ载氧体具有最佳的化学链甲烷部分氧化性能。CH₄程序升温还原（CH₄-TPR）表征发现LaMn_1/3Fe_1/3Co_1/3O_3-δ具有比LaBO₃（B=Co， Mn， Fe）更高的甲烷活化能力和晶格氧迁移性能。甲烷恒温脉冲反应（CH₄-pulse reaction）进一步证实了B位离子的协同作用可以提高LaBO₃（B=Co， Mn， Fe）的表面反应速率。程序升温氢气还原（H₂-TPR）表明，LaMn_1/3Fe_1/3Co_1/3O_3-δ中晶格氧具有适中的氧化还原能力，适合用于化学链甲烷部分氧化。     

Simultaneous Thermogravimetry and Evolved-Gas Analysis of YBa2Cu3O7 and LaBa2Cu3O7 Superconductors

Concurrent thermogravimetry (TG) and evolved-gas analysis (EGA) were done for YBa₂Cu₃O_7-z and LaBa₂Cu₃-O_7-z superconductors. The sample weights were monitored by thermobalance and the evolved O₂ and CO₂ species were monitored by quadruple mass spectrometer (QMS). No diffraction peak for the impurity phase containing a carbonate group was observed in the X-ray diffraction patterns for these samples, but the release of CO₂ was detected by EGA. CO₂ gas began to evolve from YBa₂Cu₃O_7-z at 543°C and from LaBa₂Cu₃O_7-z at 692°C. Preparation of high-quality YBa₂Cu₃O_7-z and LaBa₂Cu₃O_7-z superconductors is discussed on the basis of results of these thermal analyses.