Interfacial modification of single‐walled carbon nanotubes for high‐loading‐reinforced polypropylene composites

In this article, we present a strategy for fabricating polypropylene (PP)/polypropylene‐regrafted single‐walled carbon nanotube (PP‐re‐g‐SWNT) composites with a high loading of single‐walled carbon nanotubes (SWNTs; 20 wt %). The PP‐re‐g‐SWNTs were characterized by X‐ray photoelectron, Fourier transform infrared spectroscopy, transmission electron microscopy, and thermogravimetric analysis (TGA). The PP‐re‐g‐SWNTs showed excellent interfacial adhesion and dispersion. Furthermore, PP molecules, about 72 wt % by mass, were homogeneously bonded onto the surface of the SWNTs according to TGA. In this hybrid nanocomposite system, the PP‐re‐g‐SWNTs were covalently integrated into the PP matrix and became part of the conjugated network structure (as evidenced by differential scanning calorimetry and dynamic mechanical analysis) rather than just a separate component. Accordingly, the PP/PP‐re‐g‐SWNT composites presented obvious improvements in mechanical properties and conductivity (from 10^?10 to 10^?2). Most importantly, the tensile and flexural strength of the PP/PP‐re‐g‐SWNT composites did not exhibit an obvious downturn with the addition of 20 wt % SWNTs; this was contrary to documented results. We believe that these new observations were due to the novel structure of the PP‐re‐g‐SWNTs. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39817.     

Blend films of O‐carboxymethyl chitosan and cellulose in N‐methylmorpholine‐N‐oxide monohydrate

To introduce N‐methylmorpholine‐N‐oxide (NMMO) process to prepare antibacterial lyocell fiber, the blend films of O‐carboxymethyl chitosan (O‐CMCS) and cellulose were prepared. O‐CMCS in aqueous suspension with particles having a surface mean diameter of 2.24 μm was blended with cellulose in NMMO hydrate. The blend films with different O‐CMCS content were prepared with the blend solutions. SEM confirmed that O‐CMCS remained within the cellulose film in the particle. The mechanical properties of the blend films show little increased value when O‐CMCS was less 5%; however, it decreased sharply when O‐CMCS was over 8%. Thus, the optimum O‐CMCS content may give a good combination of antibacterial action and mechanical properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4601–4605, 2006     

Physical agglomeration behavior in preparation of cellulose‐N‐methyl morpholine N‐oxide hydrate solutions by simple mixing

The different melting temperatures of N‐methyl morpholine N‐oxide (NMMO) hydrates in the cellulose–NMMO hydrate solution may be explained by the rather different crystal structures of NMMO hydrates, which are determined by the amount of the hydrates. The preparative process of cellulose–NMMO hydrate solution may result in cellulose structural change from cellulose I to cellulose II, depending on the amount of the hydrate. Mixtures of cellulose and NMMO hydrate in a blender was changed from the granules to slurry with increasing mixing time at 60–70°C, which is below the melting point of the NMMO hydrate. In the case of 15 wt % cellulose–NMMO hydrate granules, which were made by mixing for 20 min, the melting points of various NMMO hydrates were obtained as 77.8°C (n = 0.83), 70.2°C (n = 0.97), and 69.7°C (n = 1.23), respectively, depending on the hydrate number. However, the melting points of cellulose–NMMO hydrate slurry and solution were shifted lower than those of cellulose granules, while the mixing time of slurry and solution are 25 and 35 min, respectively. These melting behaviors indicate instantaneous liquefaction of the NMMO hydrate and the diffusion of the NMMO hydrate into cellulose during mixing in a blender. When cellulose was completely dissolved in NMMO hydrate, the crystal structure of cellulose showed only cellulose II structure. In the cellulose–NMMO products of granules or slurry obtained by high‐speed mixing, which is a new preparation method, they still retained the original cellulose I structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1687–1697, 2004     

New solvent for polyrotaxane. III. Dissolution of a poly(ethylene glycol)/cyclodextrin polyrotaxane in a calcium thiocyanate aqueous solution or N‐methylmorpholine‐N‐oxide monohydrate

Calcium thiocyanate [Ca(SCN)₂] aqueous solutions above 40 wt % and N‐methylmorpholine N‐oxide (NMMO) monohydrate, which are known to dissolve cellulose, were found to be good solvents for a polyrotaxane comprising α‐cyclodextrin and poly(ethylene glycol). The polyrotaxane could be dissolved up to 12 and 10 wt % in a 40 wt % Ca(SCN)₂ aqueous solution and NMMO, respectively. These are the first instances of a neutral aqueous solution and a cyclic amine oxide, respectively, that readily dissolve the polyrotaxane. These new good solvents, as well as other solvents of the polyrotaxane, except for dimethyl sulfoxide, are identical to those of cellulose, indicating that the dissolution mechanism of the polyrotaxane is dominated by intra‐ and intermolecular hydrogen bonding of the molecule similar to that of cellulose dissolution. The concentrated polyrotaxane solution in a 40 wt % Ca(SCN)₂ aqueous solution showed apparent thixotropy and spontaneous gelation of the solution caused by a gradual increase in its viscosity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Hemodialysis membrane prepared from cellulose/N‐methylmorpholine‐N‐oxide solution. I. Effect of membrane preparation conditions on its permeation characteristics

Flat hemodialysis membranes were prepared from cellulose/N‐methylmorpholine‐N‐oxide (NMMO) solutions (dope) with different cellulose concentrations (6–8 wt %) by using a phase‐inversion method. The coagulant used was NMMO aqueous solution, of which the NMMO concentration and its temperature were varied in the range of 0 to 50 wt % and 5 to 60°C, respectively. The effects of these preparation conditions on the permeation characteristics, the ultrafiltration rate (UFR) of pure water, and sieving coefficient (SC) of dextran, were investigated. The decrease in cellulose concentration of the dope and the increases in both temperature and NMMO concentration of the coagulant gave a membrane with high UFR. Concerning the SC, the increase of the cellulose concentration and the decreases in both temperature and NMMO concentration gave a good result. Consequently, the membrane having the preferable UFR and SC as a hemodialysis membrane was obtained when the 8 wt % cellulose dope was coagulated in water at 5°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2302–2307, 2002     

Rheological characterization of cellulose solutions in N‐methyl morpholine N‐oxide monohydrate

Three different modes of rheological properties were measured on 11 and 13 wt % solutions of cellulose in N‐methyl morpholine N‐oxide (NMMO) monohydrate, in which concentration range lyocell fibers of much reduced fibrillation are preferably produced. The dynamic rheological responses revealed that the Cox–Merz rule did not hold for these cellulose solutions. Both cellulose solutions showed a shear thinning behavior over the shear rate measured at 85, 95, 105, and 115°C. However, 13 wt % solution gave rise to yield behavior at 85ºC. The power law index ranged from 0.36 to 0.58. First normal stress difference (N₁) was increased with lowering temperature and with increasing concentration as expected. Plotting N₁ vs shear stress (τ_ω) gave almost a master curve independent of temperature and concentration, whose slope was about 0.93 for both cellulose solutions over the shear rate range observed (τ_ω > 500 Pa). In addition, the cellulose solutions gave high values of recoverable shear strain (S_R), ranging from 60 to 100. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 216–222, 2002     

Hemodialysis membrane prepared from cellulose/N‐methylmorpholine‐N‐oxide solution. II. Comparative studies on the permeation characteristics of membranes prepared from N‐methylmorpholine‐N‐oxide and cuprammonium solutions

Two kinds of regenerated cellulose membranes for hemodialysis were prepared from casting solutions of N‐methylmorpholine‐N‐oxide (NMMO) and cuprammonium (denoted NMMO membranes and cuprammonium membranes, respectively). The concentration of cellulose in the casting solution investigated was 6–8 wt %. The permeation characteristics of both membrane series were compared in terms of the ultrafiltration rate (UFR) of pure water, the sieving coefficient (SC) of dextran, and the solute permeabilities of urea, creatinine, and vitamin B₁₂. The UFR and SC of the NMMO membranes were strongly affected by the cellulose concentration of the casting solution, and NMMO was a preferable solvent for the production of cellulose membranes with high performance; the cuprammonium solution gave low‐performance membranes. The pore structures of both types of membranes were estimated with the Hagen–Poiseuille law. The results showed that the NMMO membranes had larger pore radius and smaller pore numbers than the cuprammonium membranes. The differences in the membrane pore structures led to the differences in the performance between the two membrane series. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 333–339, 2003     

Atomic force microscopy of cellulose membranes prepared from the N‐methylmorpholine‐N‐oxide/water solvent system

Cellulose membranes were obtained by solutions of cellulose being cast into a mixture of N‐methylmorpholine‐N‐oxide (NMMO) and water under different processing conditions. Atomic force microscopy (AFM) was used to investigate the surface structures of the membranes. The AFM method provided information on both the size and shape of the pores on the surface, as well as the roughness of the skin, through a computerized analysis of AFM micrographs. The results obtained showed that the surface morphologies were intrinsically associated with the permeation properties. For the cellulose membranes, increasing the NMMO concentration and the temperature of the coagulation bath led to higher fluxes and lower bovine serum albumin rejection. These were always correlated with higher values of the roughness parameters and larger pore sizes of the membrane surfaces. When the cellulose concentration of the casting solution was 11 wt %, the membrane showed a nodular structure with interconnected cavity channels between the agglomerated nodules. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3389–3395, 2002     

Rheological aspects of fiber spinning from cellulose solutions in N‐methylmorpholine‐N‐oxide

Based on rheological experiments with a cellulose solution in N‐methylmorpholine‐N‐oxide (NMMO), it was found that the shearing stress generated in the flowing viscoelastic fluid decreases with an l/d ratio in a rheometer capillary. This reduces the elastic response and the outflow of the fluid becomes more uniform. At constant temperature, the elongational viscosity of the solidified stream of the cellulose solution in NMMO is reduced with increase of the deformation rate, which makes it possible to increase the fiber‐formation velocity within the air zone. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1860–1868, 2001     

UV‐cured epoxy/graphene nanocomposite films: preparation,structure and electric heating performance

UV‐cured epoxy/graphene nanocomposite films with ca 100 µm thickness were manufactured by a facile cationic photopolymerization of 3,4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexane carboxylate mixtures including graphene sheets of 0.3 ? 10.0 wt%, which was initiated by triarylsulfonium hexafluoroantimonate salts. The microstructure and thermal and electrical properties of the UV‐cured epoxy/graphene nanocomposite films were investigated as a function of the graphene content. X‐ray diffraction patterns and TEM images confirm that graphene sheets are well dispersed in the UV‐cured epoxy resin matrix even with a high graphene content of 10.0 wt%. The electrical resistance of the nanocomposite films decreased dramatically from ca 10¹² Ω to ca 10² Ω with increasing graphene content, especially at a percolation threshold of 2.0 ? 3.0 wt%. Accordingly, the UV‐cured nanocomposite films including 5.0 ? 10.0 wt% graphene showed excellent electric heating performance in terms of temperature response as well as electric power efficiency at a given applied voltage. For a nanocomposite film with 10.0 wt% graphene, the maximum temperature of ca 138 °C was attained at an applied voltage of 15 V and a high electric power efficiency of ca 3.0 ± 0.3 mW °C^?1 was achieved. © 2014 Society of Chemical Industry     

Preparation of cellulose–graphene oxide aerogels with N‐methyl morpholine‐N‐oxide as a solvent

Cellulose–graphene oxide (GO) aerogel composites were successfully prepared from cellulose and GO dispersed in N‐methyl morpholine‐N‐oxide monohydrate, a nontoxic and environmentally friendly solvent, after a freeze‐drying process. Because of the strong interactions between the numerous oxygen‐containing groups located on the surface of GO and the functional groups of the cellulose molecules, the GO monolayers were well dispersed in the three‐dimensional porous structure of the cellulose aerogels. With the addition of 10 wt % GO, the swelling ratios and water contents of the composite cellulose–GO aerogels increased from 468 to 706% and from 82.4% to 87.6%, respectively. The corresponding maximum decomposition temperatures also increased from 335 to 353 °C with increasing GO content from 0 to 10%; this indicated that the thermal stability of the cellulose–GO aerogels was enhanced. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46152.     

Effects of a pretreatment with N‐methylmorpholine‐N‐oxide on the structures and properties of ramie

To improve the dyeing properties of ramie, the ecofriendly organic solvent N‐methylmorpholine‐N‐oxide (NMMO) was used to substitute sodium hydroxide as a ramie‐fiber swelling solvent. Through padding and baking pretreatment, ramie fabric was modified by an NMMO aqueous solution. Ultraviolet–visible spectrophotometry, Fourier transform infrared spectroscopy, X‐ray diffraction, and differential scanning calorimetry were used to investigate the effects of NMMO pretreatment on the structure of the ramie, whereas the color strength (K/S, where K is the light absorption coefficient and S is the scattering coefficient), adsorption isotherm, and dye uptake rate curve were measured to investigate the effects of NMMO pretreatment on the dyeing properties of the ramie. The results show that the ramie fiber experienced a limited and irreversible swelling because of the partial breakage of interhydrogen and intrahydrogen bonds of cellulose molecules in the amorphous area, but the crystal and chemical structure of the ramie fiber did not change obviously under the experimental conditions. The K/S value of the NMMO‐modified ramie fabrics dyed with reactive dyes increased by about 100%, and the dye uptake increased by 27.88% compared to that of the raw sample, whereas the standard affinity and diffusion coefficient value of the reactive dyes on the NMMO‐modified ramie fabric were higher than those of the raw ramie fabric. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Properties of water‐soluble acrylic copolymer/montmorillonite nanocomposites for warp sizing

Acrylic copolymer/montmorillonite (MMT) nanocomposites for warp sizing were prepared in the presence of Na⁺‐MMT by the in situ intercalative polymerization of acrylic acid, acrylamide, and methyl acrylate in water solution. The properties of the solution and cast film were tested according to an application in sizing process of the nanocomposite size with various MMT contents. The results indicate that, for an exfoliated structure corresponding to the MMT content increasing to 7 wt %, the performance parameters of solution viscosity, glass‐transition temperature, and tensile strength of the film increased and the moisture sorption, abrasion loss, and elongation at break of the film decreased. When the intercalated structure of MMT was 9 wt %, the gathered MMT layers acted as a common inorganic filler in the copolymer matrix, with limited contribution to the properties of the composite. The adhesion work of the nanocomposite solution was calculated by use of the Young–Dupre relation, which showed maximum values at an MMT content of 3 wt % on the surfaces of both the polyester and cellulose films. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influences of hybrid carbon nanofillers on structures and electrical properties of sulfonated poly(1,3,4‐oxadiazole)‐based composite films

Sulfonated poly(1,3,4‐oxadiazole) (sPOD)‐based composite films, including 10 wt % hybrid carbon nanofillers composed of different weight ratios of multiwalled carbon nanotube (MWCNT) and graphene sheets, were manufactured via an efficient ultrasonication‐assisted solution mixing and casting. Fourier transform infrared (FTIR) spectra of the composite films confirmed the existence of specific interactions between sPOD backbone and MWCNT or graphene sheet. Transmission electron microscopic (TEM) images of cross sections of the composite films showed that 2‐dimensional (2D) graphene sheets formed an anisotropically oriented structure in the sPOD matrix film, but they are randomly dispersed owing to the introduction of 1‐dimensional (1D) MWCNT. Accordingly, the electrical resistivity of the composite films decreased largely from ～10³ Ω cm to ～10¹ Ω cm with the increment of the relative MWCNT content in hybrid carbon nanofillers due to the synergistic bridging effect. Thus, sPOD‐based composite films with 10 wt % hybrid carbon nanofillers exhibited high performance in electric heating by attaining rapid temperature responsiveness, high electric power efficiency, and stable maximum temperatures under given applied voltages. It was also revealed that the hybrid composite films were operationally stable over a long‐term stepwise electric heating experiment. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44499.     

The Online Measurement of Lyocell Fibers and Investigation of Elongational Viscosity of Cellulose N‐methylmorpholine‐N‐oxide Monohydrate Solutions

In this paper, the development of diameter and surface temperature of Lyocell fibers was measured online. The diameter and tensile force on the spin line in the coagulation bath were traced. The velocity, velocity gradient and the tensile stress profiles development of the fibers in the air gap were studied. The apparent elongational viscosity of cellulose N‐methylmorpholine‐N‐oxide monohydrate (NMMO‐MH) solutions was studied by steady‐state melt spinning theory. The decrease of the fiber diameter was mainly taking place near the spinneret, and the decrease of the diameter became more dramatic with increasing taking‐up speed. The surface temperature of the fibers was also dropping faster with increasing taking‐up speed for the heat transfer coefficient increased. The diameter of the Lyocell fibers almost did not change before and after it entered the coagulation bath. The tensile force on the spin line increases with increasing taking‐up speed and coagulation bath length. The velocity and the tensile stress increase slowly near the spinneret, and then accelerate. The apparent elongational viscosity of cellulose NMMO‐MH solutions decreases with increasing temperature at the same elongation rate and decreases with increasing elongation rate at the same temperature. The fiber of the Lyocell process was not really solidified in the air gap and a gel or rubbery state was formed.     

Phenomenological characterization of fabrication of aligned pristine‐SWNT and COOH‐SWNT nanocomposites via dielectrophoresis under AC electric field

Dielectrophoresis under the application of AC electric fields is one of the primary fabrication techniques (DEPFT) for obtaining aligned carbon nanotube (CNT)–polymer nanocomposites, and is used here to generate data sets from which DEPFT fabrication models in terms of CNT dispersion and orientation distribution can be developed. While the general understanding of how CNTs form aligned filaments under the influence of dielectrophoretic forces and moments is well established, detailed multi‐CNT‐filament formation predictions of microstructure evolution from a random dispersion into a more ordered structure remain intractable. As such, effort here is focused towards the development of phenomenological fabrication models for controlling local CNT dispersion and orientation as a function of applied electric field magnitude, frequency, and exposure time. In this study, 0.03 wt% single‐wall nanotubes (SWNTs) and acid treated functionalized SWNTs (COOH‐SWNTs) were dispersed in a photopolymerizable monomer blend (urethane dimethacrylate (UDMA) and 1,6‐hexanediol dimethacrylate (HDDMA)). Ultrasonication techniques were used to obtain the two different acrylate solutions i.e., 0.03% SWNTs/ UDMA/ HDDMA(9/1) solution and a 0.03% COOH‐SWNTs/UDMA/HDDMA(9/1) solution, consisting of randomly oriented, well dispersed SWNTs. Pristine SWNTs and acid treated SWNTs solutions were then subjected to controlled AC electric fields in order to explore the formation of aligned SWNT‐filaments. To assess key morphological features of the as‐produced SWNT‐acrylate and SWNT‐COOH‐acrylate nanocomposite samples, such as SWNT distribution and filament thicknesses, transmission optical microscopy has been used to observe the SWNT alignment and filament formation obtained by digitally mapping individual overlapping images. The acquisition of a large field of view with high magnification allows statistically meaningful distribution functions for morphological features to be constructed. Measurements of the as‐produced nanocomposite electrical properties in the SWNT alignment direction and transverse to it were used as a macroscale measure to confirm alignment and contiguity of the SWNT‐filament structure, with polarized Raman spectroscopy used to assess the degree of SWNT alignment at the local microscale level. It is observed that a combination of exposure time to AC electric field, and its frequency, is the key driver of filament thickness and spacing and that in general, the COOH‐SWNTs align to a greater extent than the pristine SWNTs, though they do not form filaments that are as thick and contiguous for the exposure times studied. POLYM. COMPOS., 36:1266–1279, 2015. © 2014 Society of Plastics Engineers     

Viscosity‐molecular weight relationship for cellulose solutions in either NMMO monohydrate or cuen

The intrinsic viscosities, [η], of nine cellulose samples, with molar masses from 50 × 10³ to 1 390 × 10³ were determined in the solvents NMMO*H₂O (N‐methyl morpholin N‐oxide hydrate) at 80°C and in cuen (copper II‐ethlenediamine) at 25°C. The evaluation of these results with respect to the Kuhn–Mark–Houwink relations shows that the data for NMMO*H₂O fall on the usual straight line in the double logarithmic plots only for M ≤ 158 10³; the corresponding [η]/M relation reads log ([η]/mL g⁻¹) = –1.465 + 0.735 log M. Beyond that molar mass [η] remains almost constant up to M ≈ 10⁶ and increases again thereafter. In contrast to NMMO*H₂O the cellulose solutions in cuen behave normal and the Kuhn–Mark–Houwink relation reads log ([η]/mL g⁻¹) = −1.185 + 0.735 log M. Possible reasons for the dissimilarities of the behavior of cellulose in these two solvents are being discussed. The comparison of three different methods for the determination of [η] from viscosity measurements at different polymer concentrations, c, demonstrates the advantages of plotting the natural logarithm of the relative viscosities as a function of c. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Structure and dielectric properties of polyimide/silica nanocomposite nanofoam prepared by solid‐state foaming

In this article, polyimide (PI)/silica nanocomposite nanofoams were prepared by solid‐state foaming using supercritical CO₂ as foaming agent. To control the cell size and morphology of the PI/silica foam, the silica nanoparticles as nucleating agent were in situ formation from TEOS via sol‐gel process, which make the silica nanoparticles homogeneously dispersed in PI matrix. The resulting PI/silica nanocomposite nanofoams were characterized by scanning electron microscopy (SEM), the image analysis system attached to the SEM and dielectric properties measurements. In PI/silica nanocomposite nanofoams, one type of novel morphology was shown that each cell contained one silica nanoparticle and many smaller holes about 20–50 nm uniformly located in the cell wall. This special structure could visually prove that the nucleation sites during foaming were formed on the surface of nucleating agents. Compared with those of neat PI foam, the cell size of PI/silica nanocomposite nanofoams was smaller and its distribution was narrower. The dielectric constant of PI/silica nanocomposite nanofoams was decreased because of the incorporation of the air voids into the PI/silica nanofoams. While the porosity of PI/silica nanocomposite nanofoam film was 0.45, the dielectric constant of the film (at 1 MHz) was reduced from 3.8 to about 2.6. Furthermore, the dielectric constant of PI/silica nanofoam films remained stable across the frequency range of 1×10²～1×10⁷ H_Z. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42355.     

PEDOT‐PSS/singlewall carbon nanotubes composites

Poly(3,4‐ethylenedioxythiophene)‐single wall carbon nanotube (SWNT) composites were prepared via coating methods for improving electrical conductivity and flexibility, minimizing loss of transparency. Three types of surface modified SWNTs were prepared through different modification methods: carboxylated SWNT treated with nitric acid to form carboxylic acid group on their surfaces, 1‐pyrenebutyric acid wrapped SWNT, and 1‐pyrenebutyric acid, lithium salt wrapped SWNT. The surface modifiers had influence on the dispersion states of the SWNTs in 2‐propanol. The dispersion states had influence of aggregate concentrations of surface modified SWNTs in polymer matrix, showing lower aggregate concentration for the carboxylated SWNT than those of the other surface modified SWNTs. The dispersion behaviors of SWNTs were also related with transparency and electrical resistance, and flexibility of composite films. Based on the layer‐by‐layer coating method, SWNT composite film properties such as thickness, transparency, and electrical conductivity could be controlled and would be a good example for improving contradictory properties. POLYM. ENG. SCI., 48:1–10, 2008. © 2007 Society of Plastics Engineers     

Modified cellulose fibers prepared by the N‐methylmorpholine‐N‐oxide (NMMO) process

Cellulose fibers with modified properties have been prepared from cellulose solutions in N‐methylmorpholine‐N‐oxide (NMMO). Poly(ethylene oxide) as a hydrophilic modifier and polyethylene as a hydrophobic modifier were added to the spinning solution. Based on microscope examination and measurements of such properties of fibers as porosity, moisture absorption, water retention, and tensile strength, structural changes as well as physical and mechanical properties of the resultant fibers depending on the amount of modifier added to the spinning solution were analyzed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 907–916, 2002