搅拌槽内气液两相混沌混合及分散特性

传统Rushton刚性桨常应用于过程工业中搅拌反应器内的气液分散过程,但由于桨叶背后易形成较大的气穴,气液混合效果较差。为了提高搅拌槽内气液两相的混合效果,提出了一种刚柔组合桨强化气液两相的分散过程。利用LabVIEW软件处理刚性桨和刚柔组合桨体系中气液混合过程的压力脉动信号,通过Matlab软件编程计算最大Lyapunov指数（LLE）,分析气液混合体系的混沌混合行为,同时,对刚性桨和刚柔组合桨体系中的相对搅拌功耗、整体气含率、局部气含率进行测量。结果表明,在功耗为170 W,通气量为10 m³·h^-1条件下,与刚性桨相比,刚柔组合桨能够通过刚-柔-流的耦合作用促进桨叶能量的传递过程,提高搅拌体系的混沌混合程度,刚柔组合桨体系的LLE提高了8.89%。同时,在相同操作条件下,与刚性桨相比,刚柔组合桨能够有效提高相对搅拌功耗以及搅拌槽内的整体气含率和局部气含率,且搅拌槽内气体分散更为均匀。     

刚柔组合桨强化粉煤灰酸浸搅拌槽内固液混沌混合

传统粉煤灰提铝工艺中酸浸搅拌槽均采用刚性搅拌桨。因刚性桨卷吸能力有限，导致固体颗粒易沉槽、流体混沌混合效率低。提出刚柔组合桨强化酸浸搅拌槽中固液混沌混合行为。实验基于固含率为30%的粉煤灰-自来水体系，研究了刚柔组合酸浸搅拌槽内混沌混合特性及能量耗散规律。采用扭矩传感器采集扭矩时间序列信号，借助Matlab软件编译计算混合过程中最大Lyapunov指数和多尺度熵等混沌特性参数，以单位体积功耗表征搅拌反应器的功率特性。实验考察了搅拌桨安装离底高度、柔性片长度、柔性片宽度等因素对酸浸槽内粉煤灰混沌混合的影响，对比了刚性桨与刚柔组合桨体系的能耗差异。研究结果表明：刚柔组合桨通过柔性片的作用，能增大搅拌桨的卷吸力，进而减少固体颗粒沉槽现象，促进全槽混沌混合；在最优化条件（120 r/min，搅拌桨安装离底高度为T/4，柔性片长度为1.2H ₁、柔性片宽度为D/8）下，体系最大Lyapunov指数达到最大值0.0645，各尺度下的MSE均比其他条件更大，表明刚柔组合桨能够通过柔性片的多体运动，强化体系混沌混合，均化体系能量分布；刚性桨与刚柔组合桨的单位体积功耗随着转速的增加呈现指数规律增长。     

搅拌槽内气液两相混沌混合及分散特性

传统Rushton刚性桨常应用于过程工业中搅拌反应器内的气液分散过程,但由于桨叶背后易形成较大的气穴,气液混合效果较差。为了提高搅拌槽内气液两相的混合效果,提出了一种刚柔组合桨强化气液两相的分散过程。利用Lab VIEW软件处理刚性桨和刚柔组合桨体系中气液混合过程的压力脉动信号,通过Matlab软件编程计算最大Lyapunov指数(LLE),分析气液混合体系的混沌混合行为,同时,对刚性桨和刚柔组合桨体系中的相对搅拌功耗、整体气含率、局部气含率进行测量。结果表明,在功耗为170 W,通气量为10 m3?h-1条件下,与刚性桨相比,刚柔组合桨能够通过刚-柔-流的耦合作用促进桨叶能量的传递过程,提高搅拌体系的混沌混合程度,刚柔组合桨体系的LLE提高了8.89%。同时,在相同操作条件下,与刚性桨相比,刚柔组合桨能够有效提高相对搅拌功耗以及搅拌槽内的整体气含率和局部气含率,且搅拌槽内气体分散更为均匀。     

刚柔组合搅拌桨强化搅拌槽中流体混沌混合

搅拌槽内普遍存在着两种不同类型的混合区域：混沌混合区和规则区。增大混沌混合区,是提高流体混合效率、降低搅拌过程能耗的重要途径。而合理设计搅拌桨有助于流体形成适宜的流动状态,实现混沌混合。柔性体与刚性体组合,可设计出具有多体运动行为的刚柔组合搅拌桨,可强化流体混沌混合行为。结合Matlab 软件,实验研究了双层桨搅拌槽内自来水体系的最大Lyapunov指数（LLE）和多尺度熵（MSE）的变化规律,对比分析了刚性桨和刚柔组合桨两种桨叶对流体混沌混合的影响。结果表明,刚柔组合桨强化流体的运动特性,使更多流体进入混沌混合状态。在转速为210 r·min^-1时,流体的混沌混合达到最佳状态,刚性桨体系的LLE为0.041,而刚柔组合桨体系的LLE为0.048;刚柔组合桨可有效耗散能量,使整个槽体的能量分布均匀,刚柔组合桨在150 r·min^-1时的多尺度熵率与刚性桨在210 r·min^-1时基本相近;刚柔组合桨体系的混合时间均低于刚性桨体系,在转速为120 r·min^-1时,刚柔组合桨使流体的混合时间缩短了26%左右。刚柔组合桨可改变流场结构和能量耗散方式,强化流体混沌混合,实现高效节能操作。     

穿流式刚-柔组合搅拌桨强化混合澄清槽内油-水两相混沌混合

运用LabView和Matlab软件分别采集和处理穿流式刚-柔组合搅拌桨扰动澄清槽中油-水两相流体内部的压力脉动信号,得出的最大Lyapunov指数（LLE）和多尺度熵（MSE）,反映流体内部的混沌程度;同时采用流场可视化技术观测流体混合状态。结果表明,相比于刚性组合桨,穿流式刚-柔组合搅拌桨通过穿流孔与柔性部分的共同作用改变流场的结构和能量耗散方式,使流体的混沌程度和混合状态都优于刚性组合桨。当转速为88 r·min^-1时,流体的混沌混合都达到最佳状态,各实验条件下的LLE均大于零,表明流场混合体系已进入混沌状态,且穿流式刚-柔组合搅拌桨体系的MSE明显高于刚性组合桨体系,说明穿流式刚-柔组合搅拌桨的混合效果优于刚性组合桨。另外,柔性片上穿流孔的数目和柔性桨叶的厚度对流场的混沌特性也有明显的影响。     

脉冲射流-刚柔组合桨强化流体混沌混合及传质性能研究

传统搅拌反应器普遍使用刚性桨进行机械搅拌，导致反应器内容易产生混合隔离区而降低流体混合效率。采用多流场耦合诱发混沌现象，促使更多流体进入混沌状态，是提高流体混合效率的有效途径之一。结合Matlab软件编译PJ-RF-RT体系中的压力脉动信号得到最大Lyapunov指数（LLE）与多尺度熵（MSE），探究不同脉冲周期下占空比、桨型、柔性桨叶厚度、桨离底高度及脉冲空气射流量对搅拌反应器内流体混沌混合的影响，同时，对比分析了桨型、射流类型、气流量对体积氧传质系数K_La的影响。研究结果表明，在脉冲周期T=0.4 s，占空比D=80%时，RF-RT桨体系较R-RT桨体系的LLE增大了11.58%，且RF-RT体系的MSE显著高于R-RT桨体系，表明脉冲射流刚柔组合桨体系能更好地诱发流体混沌，增大流体混合效率，均化体系能量分布。此外，脉冲射流耦合RF-RT桨体系增强了流体的湍流特性，促使液膜厚度减小，强化了传质，在单位体积功耗P_v=360 W/m³时，PJ-RF-RT体系的K_La较PJ-R-RT提高了13.46%，PJ-R-RT体系的K_La较SJ-R-RT提高了11.86%。     

长短叶片复合型刚柔桨强化搅拌槽内流体混沌混合行为

搅拌反应器中混合隔离区的存在是强化流体混合的主要障碍。打破搅拌槽中的对称性流场结构，破坏混合隔离区，可以提高流体混合效率。采用Matlab软件编程计算最大Lyapunov指数（LLE）和多尺度熵（MSE），比较了不同桨叶类型、柔性片长度、柔性片数量和桨叶离底高度以及转速对流体混合的影响。结果表明，长短叶片复合型刚柔桨（RF-LSB）桨叶通过刚柔耦合错位连接，柔性片的形变与随机振动对流体的非稳态扰动，使流场结构不稳定性和不对称性增强，强化了流体混合效果。当柔性片数量为3，搅拌转速为90 r/min时，RF-LSB体系比刚性桨和刚柔桨体系的LLE值分别提高了20.22%和7.98%；三种体系[RF-LSB（柔性片数量为3）、刚性桨和刚柔桨体系]的混合时间（θ_m）与单位体积功耗（P_v）呈指数型关系，当P_v相同时，RF-LSB（柔性片数量为3）的θ_m最小，表明RF-LSB（柔性片数量为3）更有利于流体混沌混合。     

穿流式刚-柔组合搅拌桨强化混合澄清槽内油-水两相混沌混合

运用Lab View和Matlab软件分别采集和处理穿流式刚-柔组合搅拌桨扰动澄清槽中油-水两相流体内部的压力脉动信号,得出的最大Lyapunov指数(LLE)和多尺度熵(MSE),反映流体内部的混沌程度;同时采用流场可视化技术观测流体混合状态。结果表明,相比于刚性组合桨,穿流式刚-柔组合搅拌桨通过穿流孔与柔性部分的共同作用改变流场的结构和能量耗散方式,使流体的混沌程度和混合状态都优于刚性组合桨。当转速为88 r·min-1时,流体的混沌混合都达到最佳状态,各实验条件下的LLE均大于零,表明流场混合体系已进入混沌状态,且穿流式刚-柔组合搅拌桨体系的MSE明显高于刚性组合桨体系,说明穿流式刚-柔组合搅拌桨的混合效果优于刚性组合桨。另外,柔性片上穿流孔的数目和柔性桨叶的厚度对流场的混沌特性也有明显的影响。     

刚柔组合桨强化粉煤灰酸浸搅拌槽内固液混沌混合

传统粉煤灰提铝工艺中酸浸搅拌槽均采用刚性搅拌桨。因刚性桨卷吸能力有限,导致固体颗粒易沉槽、流体混沌混合效率低。提出刚柔组合桨强化酸浸搅拌槽中固液混沌混合行为。实验基于固含率为30%的粉煤灰-自来水体系,研究了刚柔组合酸浸搅拌槽内混沌混合特性及能量耗散规律。采用扭矩传感器采集扭矩时间序列信号,借助Matlab软件编译计算混合过程中最大Lyapunov指数和多尺度熵等混沌特性参数,以单位体积功耗表征搅拌反应器的功率特性。实验考察了搅拌桨安装离底高度、柔性片长度、柔性片宽度等因素对酸浸槽内粉煤灰混沌混合的影响,对比了刚性桨与刚柔组合桨体系的能耗差异。研究结果表明:刚柔组合桨通过柔性片的作用,能增大搅拌桨的卷吸力,进而减少固体颗粒沉槽现象,促进全槽混沌混合;在最优化条件(120 r/min,搅拌桨安装离底高度为T/4,柔性片长度为1.2H1、柔性片宽度为D/8)下,体系最大Lyapunov指数达到最大值0.0645,各尺度下的MSE均比其他条件更大,表明刚柔组合桨能够通过柔性片的多体运动,强化体系混沌混合,均化体系能量分布;刚性桨与刚柔组合桨的单位体积功耗随着转速的增加呈现指数规律增长。     

错位刚柔桨强化搅拌槽内流体混合实验及数值模拟

为消除搅拌反应器中混合隔离区，对标准刚性桨（R-RT）、错位刚性桨（PR-RT）和错位刚柔桨（PRF-RT）三种桨叶体系的流体混沌特性参数、流场结构以及流体运动速度进行了探讨。采用Matlab软件编程计算最大Lyapunov指数（LLE）和多尺度熵（MSE），通过计算流体力学研究了三种桨叶体系流场结构和流体运动速度的差异。实验及计算结果表明，错位刚柔桨通过柔性桨叶的随机扰动破坏了隔离区介稳态流场边界，较大程度地消除了混合隔离区。PRF-RT的LLE相比于R-RT和PR-RT分别提高了13.29%和7.25%，MSE也较PR-RT和R-RT大；PRF-RT增强了流场不稳定性，形成了不对称性流场结构，减少了隔离区分布范围；PRF-RT强化桨叶能量耗散，提高了搅拌槽底部、顶部液面以及搅拌槽壁区域流体运动速度，减小了流体混合时间。     

Chaotic mixing and droplet dispersion characteristics of liquid - liquid with elastic combined impeller

Traditional mixing and clarification tanks generally use rigid stirring blades to achieve liquid-liquid two-phase mixed extraction, which generally suffers from low efficiency and high energy consumption. A kind of elastic combined impeller was used in the mixing clarifier in this work to enhance the liquid-liquid biphase mixing behavior. Lyapunov exponent (LLE) and multiscale entropy (MSE) were used to characterize the chaotic state of the system, the particle size distribution and D₃₂ were used to characterize the dispersion effect. The influence of impeller type (elastic combined impeller, rigid-flexible combined impeller and rigid impeller), spring length, wire diameter and outer diameter on mixing effect was studied. The results indicated that compared with the rigid impeller and the rigid-flexible combined impeller, the elastic combined impeller strengthens the energy dissipation mode of the flow field through the deformation and energy storage of the spring, improves the dispersion effect of the dispersed phase, and was conducive to the chaotic mixing of the liquid-liquid biphase. When stirring speed N = 200 r/min, the spring wire diameter was 0.6 mm, the relative length of the spring was 1.2, and the external diameter of the spring was 7 mm, the LLE value and the amplitude of MSE were the largest and the MSE values fluctuate most strongly. At the same time, there was a log-linear relationship between the D₃₂ of dispersed phase and the stirring speed in each stirring system, and the droplet size of dispersed phase in the elastic combined impeller system was smaller and more.     

Chaotic mixing performance and mass transfer enhanced by rigid-flexible impeller with pulse jet

Conventional stirred reactors generally use rigid impeller for mechanical stirring, which leads to the easy creation of isolation mixing regions in the reactor and reduces the efficiency of fluid mixing. The use of multi-flow field coupling to induce chaos and promote more fluids into a chaotic state is one of the effective ways to improve fluid mixing efficiency. In this work, the largest Lyapunov exponent(LLE) and multi-scale entropy(MSE) are investigated with the Matlab compile pressure pulsation signals. The effects of duty ratio, paddle type, flexible paddle thickness, paddle height from the bottom and pulsed air jet flow rate on the chaotic mixing of fluids in a stirred reactor under different pulse periods are explored. In addition, the effects of different impeller types, jet types and air jet flow rate on the volume oxygen mass transfer coefficient K_La are compared and analyzed. When T=0.4 s and D=80%, the results show that the LLE of the rigid-flexible RT impeller compared with the rigid RT impeller increases 11.58% and the MSE of the rigid-flexible RT impeller is also larger than that of rigid RT impeller. It was showed that the pulsed jet rigid-flexible impeller system can better enhance fluid chaos, increase the fluid mixing efficiency and homogenize the system energy distribution. In addition, pulse jet coupling RF-RT impeller system enhances the turbulent characteristics of the fluid, promotes the reduction of the thickness of the liquid film, strengthens the mass transfer and increases the K_La value of the system. When power consumption per unit volume is 360 W/m³, the K_La of the PJ-RF-RT system compared with the PT-R-RT system increases 13.46%, and the K_La of the PJ-R-RT system compared with the SJ-R-RT system increases 11.86%.     

Experiment and numerical simulation of chaotic mixing performance enhanced by perturbed rigid-flexible impeller in stirred tank

To eliminate the isolated mixing regions in the stirred tank, factors associated with chaotic mixing performance were studied, including flow field structure and fluid velocity of rigid RT impeller (R-RT), perturbed rigid RT impeller (PR-RT) and perturbed rigid-flexible RT impeller (PRF-RT). The maximum Lyapunov exponent (LLE) and multi-scale entropy (MSE) were calculated by using Matlab software programming, and the differences in flow field structure and fluid velocity of the three blade systems were studied through computational fluid mechanics. The experimental and computational results showed that perturbed rigid-flexible RT impeller could destroy the boundary of the mesostatic flow field in the isolated mixing regions and the symmetry flow in the process of fluid mixing through the random disturbance of the flexible blade, eliminating the isolated mixing regions. At 90 r/min, the LLE of the perturbed rigid-flexible RT impeller is larger than that of rigid RT impeller and perturbed rigid RT impeller. The LLE of the rigid-flexible RT impeller compared with the rigid RT impeller and perturbed rigid RT impeller increases 13.29% and 7.25% respectively and the MSE of the perturbed rigid-flexible RT impeller is also larger than that of rigid RT impeller and perturbed rigid RT impeller. The perturbed rigid-flexible RT impeller enhances the flow field instability, forms an asymmetric flow field structure, and reduces the distribution range of isolated mixing regions. The perturbed rigid-flexible RT impeller enhances the energy dissipation of the blade, improves the fluid velocity at the bottom and top of the tank and the wall of the tank, and reduces the mixing time.     

湿法磷酸固-液体系混沌混合与浸出强化行为

湿法磷酸浸出过程中，传统刚性搅拌桨的作用方式主要是剪切作用，容易形成对称性流场结构，降低搅拌效率。实验考察了桨叶类型、离底高度、搅拌速度、柔性钢丝绳长度、柔性钢丝直径对磷矿浸出率及最大Lyapunov指数(LLE)的影响。实验结果表明：刚柔组合桨通过刚-柔-流的耦合作用，改善流场的结构，提高了流体混沌混合效果。当搅拌转速225 r/min，浸出时间120 min，离底高度h=T/4，柔性钢丝绳直径d= 0.42r，柔性钢丝绳长度L=1.3T时，刚柔组合桨的最大Lyapunov指数达到0.09071，磷矿浸出率提高了10.8%。另外，在相同的功耗(P _v=9890 W/m³)条件下，刚柔组合桨使反应器内的悬浮均匀度和渣中磷含量分别降低了40.8%和17.67%，有效地改善了晶体的形貌，提高了磷石膏的过滤性能，强化了颗粒的混合与浸出。     

Enhancement of liquid–liquid mixing in a mixer-settler by a double rigid-flexible combination impeller

Mixing is crucial in the dispersion of two immiscible fluids. The rational design of an impeller is necessary to form suitable flow conditions and improve fluid mixing efficiency. A double rigid-flexible combination impeller was designed by connecting the upper and lower rigid impeller blades with flexible pieces. Experimental measurements were performed in a laboratory-scale mixer-settler under different impeller types. The largest Lyapunov exponent (LLE) and multi-scale entropy (MSE) were investigated using Matlab. Results showed that the double rigid-flexible combination impeller enhanced liquid–liquid mixing in the mixer-settler through the multiple-body motion behavior triggered by the swings of flexible pieces. At the optimum mixing point of each impeller, the LLEs of the double impeller, double rigid combination impeller, and double rigid-flexible combination impeller were 0.018, 0.055, and 0.057, respectively. At 75 rpm, the MSE of the combination impellers was obviously greater than that of the double impeller, and the rigid-flexible combination impeller had larger MSE than the double rigid combination impeller. The mixing efficiency of the rigid-flexible combination impeller increased with increasing width and quantity of the flexible piece. The quantity of rigid blade slice also influenced the enhancement of mixing ability. The double rigid-flexible combination impeller intensified the chaotic mixing of the two-phase fluid by changing the flow field structure and energy dissipation mode, ultimately achieving an efficient-mixing operation.     

Chaotic mixing performance enhanced by rigid-flexible impeller with long-short blades in stirred tank

The presence of a mixing isolation regions in a stirred reactor is a major obstacle to enhancing fluid mixing. Breaking the symmetrical flow field structure in the stirred tank and destroying the mixing isolation area can improve the fluid mixing efficiency. The Matlab software was used to calculate the maximum Lyapunov exponent (LLE) and multi-scale entropy (MSE). The effects of different blade types, flexible blade length, flexible blade number, blade height from bottom and rotation speed on fluid mixing were compared. The results show that the rigid-flexible impeller with long-short blades (RF-LSB) can enhance the flow field structure more unstable and asymmetric with deformation and random vibration of flexible pieces, destroy the symmetry flow in the process of fluid mixing, induce the asymmetric flow field, and make more fluid into the chaotic state. When at 90 r/min and three pieces of flexible, the LLE of the RF-LSB is larger than that of rigid impeller and rigid-flexible impeller RF-LSB with increase of 20.22% and 7.98% respectively. The mixing time (θ_m) of the three systems [RF-LSB (three pieces), rigid impeller, rigid-flexible impeller] has an exponential relationship with the power consumption per unit volume (P_v). When P_v is constant, θ_m of the RF-LSB system is the smallest. Results showed that the RF-LSB (three pieces) is superior to rigid impeller and rigid-flexible impeller, which is more conducive to fluid chaotic mixing.