Pultruded fiber-reinforced poly(methyl methacrylate) composites. II. Static and dynamic mechanical properties,environmental effect,and postformability

This paper presents a novel process developed to manufacture poly(methyl methacrylate) (PMMA) pultruded composite. The mechanical, thermal, and dynamic mechanical properties, environmental effect, postformability of various fiber (glass, carbon, and Kevlar 49 aramid fiber) reinforced pultruded PMMA composites have been studied. Results show mechanical properties (i.e., tensile strength, specific tensile strength, tensile modulus, and specific flexural strength) and thermal properties (HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest specific tensile strength and HDT, carbon fiber/PMMA composites show the highest tensile strength and tensile modulus, and glass fiber/PMMA composites show the highest specific flexural strength. Pultruded glass-fiber-reinforced PMMA composites exhibit good weather resistance. These composite materials can be postformed by thermoforming under pressure, and mechanical properties of postformed products can be improved. The dynamic shear storage and loss modulus (G′, G″) of pultruded glass-fiber-reinforced PMMA composites increased with decreasing pulling rate, and their shear storage moduli are higher than those of pultruded Nylon 6 and polyester composites.     

Interpenetrating polymer networks of polyurethane and furfuryl alcohol,IIa. Processability and properties of pultruded fiber-reinforced composites

A feasibility study of pultrusion of fiber-reinforced polyurethane/furfuryl alcohol (PU/FA) interpenetrating polymer/network IPN composites has been made. From the viscosity study, it was found that the pot life of the PU/FA IPN prepolymers increased with PU content and showed high reactivity at elevated temperature. It was confirmed from the morphological study that the wetting of fibers by the PU/FA IPN resins was improved with PU content. The appearance of the tensile failure surfaces of the pultruded glass fiber-reinforced PU/FA IPN composites showed “hackle patterns” for PU contents below 15 phr. The mechanical property study shows that the tensile strength of pultruded PU/FA IPN composites is the highest when the PU content is 5 phr. However, the flexural strength, flexural modulus and HDT decreased with PU content. The mechanical properties of various fiber-reinforced (glass, carbon, and Kevlar 49 aramid fiber) pultruded PU/FA IPN composites increased with fiber volume content.     

The unidirectional glass fiber reinforced furfuryl alcohol for pultrusion. II. Correlation of processing parameters for optimizing the process

Unidirectional glass fiber reinforced furfuryl alcohol (FA) composites have been prepared by the pultrusion processes. The optimum processing parameters of the glass fiber reinforced FA composites by pultrusion has been studied. The effects of the optimum processing parameters on the properties (flexural strength, flexural modulus, notched Izod impact strength, glass transition temperature (T_g), dynamic shear storage modulus (E'), shrinkage ratio, and roughness) investigated including die temperature, pulling rate, postcure temperature and time, and filler type and content. Results show that the pultruded composites possessed various optimum pulling rates at different die temperatures. On the basis of the DSC diagram, the swelling ratio and the mechanical properties of pultruded composites, the optimum die temperature can be determined. The mechanical properties and T_g increase at a suitable postcure temperature and time. Furthermore, the properties which decrease due to the degradation of pultruded composites for a long postcure time will be discussed. The mechanical properties of pultruded composites reach a maximum value at various filler content corresponding to the talc and calcium carbonate, respectively, and then decreased. When the fillers are added to the pultruded glass fiber reinforced FA composites, the shrinkage ratio of composites become smaller, and the surface of composites became smooth. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

碳纤维改性HA/PMMA生物复合材料力学性能的研究

采用原位合成与溶液共混相结合的方法,制备了短切碳纤维增强纳米羟基磷灰石(HA)/聚甲基丙烯酸甲酯(PMMA)生物复合材料。研究了碳纤维的含量和长度对HA/PMMA复合材料结构和力学性能的影响。采用万能材料试验机和扫描电子显微镜对复合材料的力学性能及断面的微观形貌进行了测试和表征。结果表明:碳纤维在HA/PMMA复合材料中分布均匀,有效提高了复合材料的力学性能;碳纤维含量为4%时,复合材料的拉伸强度、弯曲强度、压缩强度和弹性模量等均达到最大值;复合材料的断裂伸长率随碳纤维含量的增加而减小;当碳纤维含量一定时,随其长度的增加,复合材料的拉伸强度、弯曲强度和弹性模量均增加,但断裂伸长率降低。     

Pultruded fiber reinforced thermoplastic poly(methyl methacrylate) composites. Part I. Correlation of processing parameters for optimizing the process

The effect of processing parameters on the properties (tensile, flexural strength and modulus and impact strength, etc.) of pultruded fiber reinforced poly(methyl methacrylate) (PMMA) composites has been studied. The processing parameters investigated included pulling rate, die temperature, and postcure. Wetting of fibers by PMMA resin was complete, and the fiber bundles were evenly distributed in the PMMA matrix. The conversion, molecular weight and viscosity of MMA prepolymer were studied by ¹H-NMR, GPC and Brookfield viscometer. The optimum die temperature was determined from DSC diagram, molecular weight measurement and from the polymerization rate. The mechanical properties increased with the increasing postcure temperature and decreasing pulling rate and die temperature.     

Mechanical and thermal properties of hierarchical composites enhanced by pristine graphene and graphene oxide nanoinclusions

Epoxy resin nanocomposites incorporated with 0.5, 1, 2, and 4 wt % pristine graphene and modified graphene oxide (GO) nanoflakes were produced and used to fabricate carbon fiber‐reinforced and glass fiber‐reinforced composite panels via vacuum‐assisted resin transfer molding process. Mechanical and thermal properties of the composite panels—called hierarchical graphene composites—were determined according to ASTM standards. It was observed that the studied properties were improved consistently by increasing the amount of nanoinclusions. Particularly, in the presence of 4 wt % GO in the resin, tensile modulus, compressive strength, and flexural modulus of carbon fiber (glass fiber) composites were improved 15% (21%), 34% (84%), and 40% (68%), respectively. Likewise, with inclusion of 4 wt % pristine graphene in the resin, tensile modulus, compressive strength, and flexural modulus of carbon fiber (glass fiber) composites were improved 11% (7%), 30% (77%), and 34% (58%), respectively. Also, thermal conductivity of the carbon fiber (glass fiber) composites with 4% GO inclusion was improved 52% (89%). Similarly, thermal conductivity of the carbon fiber (glass fiber) composites with 4% pristine graphene inclusion was improved 45% (80%). The reported results indicate that both pristine graphene and modified GO nanoflakes are excellent options to enhance the mechanical and thermal properties of fiber‐reinforced polymeric composites and to make them viable replacement materials for metallic parts in different industries, such as wind energy, aerospace, marine, and automotive. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40826.     

Mechanical properties of natural fiber hybrid composites based on renewable thermoset resins derived from soybean oil,for use in technical applications

Natural fiber composites are known to have lower mechanical properties than glass or carbon fiber reinforced composites. The hybrid natural fiber composites prepared in this study have relatively good mechanical properties. Different combinations of woven and non‐woven flax fibers were used. The stacking sequence of the fibers was in different orientations, such as 0°, +45°, and 90°. The composites manufactured had good mechanical properties. A tensile strength of about 119 MPa and Young's modulus of about 14 GPa was achieved, with flexural strength and modulus of about 201 MPa and 24 GPa, respectively. For the purposes of comparison, composites were made with a combination of woven fabrics and glass fibers. One ply of a glass fiber mat was sandwiched in the mid‐plane and this increased the tensile strength considerably to 168 MPa. Dynamic mechanical analysis was performed in order to determine the storage and loss modulus and the glass transition temperature of the composites. Microstructural analysis was done with scanning electron microscopy. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of macromolecular coupling agent on the property of PP/GF composites

Silane‐grafted polypropylene manufactured by a reactive grafting process was used as the coupling agent in polypropylene/glass‐fiber composites to improve the interaction of the interfacial regions. Polypropylene reinforced with 30% by weight of short glass fibers was injection‐molded and the mechanical behaviors were investigated. The results indicate that the mechanical properties (tensile strength, tensile modulus, flexural strength, flexural modulus, and Izod impact strength) of the composite increased remarkably as compared with the noncoupled glass fiber/polypropylene. SEM of the fracture surfaces of the coupled composites shows a good adhesion at the fiber/matrix interface: The fibers are coated with matrix polymer, and a matrix transition region exists near the fibers. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1537–1542, 1999     

碳纤维含量对PMMA-PMA基复合材料显微结构及力学性能的影响(英文)

以甲基丙烯酸甲酯(polymethyl methacrylate,PMMA)和丙烯酸甲酯(polymethyl acrylate,PMA)为原料、短切碳纤维(Cf)为增强相,采用悬浮聚合法制备碳纤维增强聚甲基丙烯酸甲酯-聚丙烯酸甲酯基复合材料(carbon fiber-reinforced polymethyl methacrylate-polymethyl acrylate matrix composites,Cf/PMMA-PMA)。研究碳纤维含量(质量分数,下同)对Cf/PMMA-PMA显微结构及力学性能(抗折强度、抗压强度和拉伸强度)的影响。结果表明:随碳纤维含量增加,Cf/PMMA-PMA的挠度呈线性增长,而抗折强度、抗压强度和拉伸强度呈先增大后减小趋势。当碳纤维含量为15%时,Cf/PMMA-PMA的抗折强度、抗压强度和拉伸强度分别达到最大值115.5、244.6MPa和158.6MPa。     

锦葵纤维增强聚丙烯基复合材料力学性能研究

分别制备了锦葵纤维含量为10 %（质量分数,下同）、20 %、30 %、40 %和50 %的锦葵纤维增强增强聚丙烯基复合材料,研究了纤维含量对该复合材料拉伸性能和弯曲性能的影响,并与苎麻纤维增强聚丙烯基复合材料进行了对比。结果表明,随着锦葵纤维含量的增加,锦葵纤维增强聚丙烯基复合材料的拉伸强度和拉伸弹性模量逐渐增加,而弯曲强度和弯曲弹性模量呈现先增大后减小的趋势,当纤维含量为40 %时达最大值;纤维含量均为30 %时,除拉伸弹性模量外,锦葵纤维增强聚丙烯基复合材料的各项指标均低于苎麻纤维增强聚丙烯基复合材料。     

The influence of addition of carbon nanotube and graphene platelets on characteristics of carbon/basalt fiber reinforced intra-ply hybrid composites

In this study, effects of addition of carbon nanotubes (CNTs) and graphene platelets (GPLs) on characteristics of carbon/basalt fiber reinforced intra-ply hybrid composites were investigated. The composites were fabricated using vacuum assisted resin infusion molding (VARIM) method in two types including bare and 0.1, 0.5 wt.% of GPL and CNT nanoparticles filled hybrid composites. Fabricated normal and multiscale composites were cut by water jet and mechanical properties of specimens were examined by tensile, flexural, SBS experiments. Therefore, the modulus of elasticity, flexural modulus, tensile and flexural strength and ILSS of bare and multiscale composites were compared. Thermomechanical properties of fabricated composites were evaluated by dynamic mechanic analyze (DMA), thermogravimetric analyze ( TGA) and thermal conductivity (TC) tests and storage modulus, loss modulus, damping ratio, glass transition temperature, weight loss and derivative weight loss were compared in fabricated normal and multiscale composites. Similarly, modal properties of fabricated composites such as natural frequency and damping factor were obtained by vibrational tests and compared in fabricated composites. According to the results, the addition of carbon-based nanoparticles improved the characteristics of carbon/basalt fiber intra-ply hybrid composites. The response of composites was directly proportional to the addition ratio of the carbon-based nanoparticles.     

Hybrid carbon-glass fiber vinyl ester resin composites

Hybrid carbon-glass fiber composites of novolak epoxy-based vinyl ester resins have been investigated. The chemical resistance, the thermo-oxidative stability and the mechanical properties such as tensile strength and tensile modulus, as well as flexural strength and flexural modulus, interlaminar shear strength (ILSS) and impact strength have also been estimated. The combination of glass and carbon fibers in the hybrid turns out to be an excellent mix. These composites have good tensile and flexural properties as well as the good chemical resistance of the carbon fibers and the high impact strength of the glass fibers and also the thermo-oxidative stability of highly aromatic vinyl ester resins based on novolak epoxy.     

Study on effects of short glass fiber reinforcement on the mechanical and thermal properties of PC/ABS composites

This article mainly investigated the length distributions of the alkali‐free short glass fibers in specimens and their effect on the mechanical and thermal properties of the composites. The results show that the initial length, addition level and feed way of the fibers have obvious effects on the length distributions of fibers in specimens, and thereby the mechanical and thermal properties of the composites. The main‐direction feed way has an intense shear action on the fibers in specimens. With the increase of the fiber content, the reinforcing effect of fibers on the tensile strength, flexural strength and flexural modulus of the composites is increased, while the impact strength is decreased first and then tends to be stable, and the strength factor (F) of the tensile strength to weld line is significantly reduced. The longer the fiber lengths in specimens are, the more obvious the reinforcing and toughening effects are. To some extent, with the increase of the fiber content, the storage modulus (E′) and loss modulus (E′′) of the specimens are increased, but the loss factor (Tan δ) is reduced. The effect of the fiber initial lengths on the heat‐degradation of composites is smaller than that of the fiber content. Meanwhile, adding fibers can improve the thermal stability of the composites, and this law is also confirmed by the heat deflection temperature (HDT) test. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40697.     

Short glass fiber reinforced ABS and ABS/PA6 composites: Processing and characterization

In this study acrylonitrile‐butadiene‐styrene (ABS) terpolymer was reinforced with 3‐aminopropyltrimethoxysilane (APS)‐treated short glass fibers (SGFs). The effects of SGF concentration and extrusion process conditions, such as the screw speed and barrel temperature profile, on the mechanical properties of the composites were examined. Increasing the SGF concentration in the ABS matrix from 10 wt% to 30 wt% resulted in improved tensile strength, tensile modulus and flexural modulus, but drastically lowered the strain‐at‐break and the impact strength. The average fiber length decreased when the concentration of glass fibers increased. The increase in screw speed decreased the average fiber length, and therefore the tensile strength, tensile modulus, flexural modulus, and impact strength were affected negatively and the strain‐at‐break was affected positively. The increase in extrusion temperature decreased the fiber length degradation, and therefore the tensile strength, tensile modulus, flexural modulus, and impact strength increased. At higher temperatures the ABS matrix degraded and the mechanical strength of the composites decreased. To obtain a strong interaction at the interface, polyamide‐6 (PA6) at varying concentrations was introduced into the ABS/30 wt% SGF composite. The incorporation and increasing amount of PA6 in the composites broadened the fiber length distribution (FLD) owing to the low melt viscosity of PA6. Tensile strength, tensile modulus, flexural modulus, and impact strength values increased with an increase in the PA6 content of the ABS/PA6/SGF systems due to the improved adhesion at the interface, which was confirmed by the ratio of tensile strength to flexural strength as an adhesion parameter. These results were also supported by scanning electron micrographs of the ABS/PA6/SGF composites, which exhibited an improved adhesion between the SGFs and the ABS/PA6 matrix. POLYM. COMPOS. 26:745–755, 2005. © 2005 Society of Plastics Engineers     

剑麻纤维/长玻纤混杂增强PP复合材料的力学性能研究

采用剑麻纤维(SF)和长玻璃纤维(LGF)混杂增强聚丙烯(PP)复合材料,考察了SF/LGF的比例和含量对PP复合材料力学性能的影响。结果表明:SF/LGF在聚丙烯树脂基体中呈交叉网状分布,这有利于提高复合材料的冲击强度、弯曲模量、拉伸强度和软化点。在SF/LGF质量比为2 2∶,二者总质量分数为30%时,SF/LGF混杂增强PP复合材料的综合力学性能较好。     

PVDF/PMMA/Basalt fiber composites: Morphology,melting and crystallization,structure, mechanical properties,and heat resistance

This paper is to study the effect of basalt fiber on morphology, melting and crystallization, structure, mechanical properties, melting and crystallization of PVDF/PMMA composites using scanning electron microscopy (SEM), X‐ray, differential scanning calorimeter (DSC), dynamical mechanical analysis (DMA), etc. Basalt fiber may disperse well in PVDF/PMMA matrix and form compact fiber network, and this makes tensile and flexural strength of fiber reinforced PVDF/PMMA composites get to the maximum value of 62 and 102 MPa, respectively. However, the mechanical properties begin to decrease when basalt fiber content exceeds 20 wt %. The α and β phase of PVDF can coexist in composites, and basalt fiber and PMMA can induce β phase of PVDF. The melting temperature of PVDF in composites is kept unchanged, but the degree of crystallinity of composites increases as basalt fiber content increase, and then declines when fiber content exceeds 20%. The DSC results confirm that the nucleation ability of PVDF is enhanced by basalt fiber. Also, the heat resistance of PVDF/PMMA composite is improved from 133 to 146.1°C due to basalt fiber. The DMA shows that basalt fiber increases the storage modulus of PVDF/PMMA composite, and the loss peak of PMMA increases from 116.1 to 130°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40494.     

Flexural properties of S‐2 glass and TR30S carbon fiber‐reinforced epoxy hybrid composites

A study on the flexural properties of hybrid composites reinforced by S‐2 glass and TR30S carbon fibers is presented in this article. Test specimens were made by the hand lay‐up process in an intraply configuration with varying numbers of glass/epoxy laminas substituted for carbon/epoxy laminas. These specimens were then tested in the three point bend configuration in accordance with ASTM D790‐07 at a span to depth ratio of 32. The failed specimens were examined under an optical microscope, and the results show that the dominant failure mode is at the compressive side. The flexural behavior was also simulated by finite element analysis (FEA). Based on the FEA results, the flexural modulus and flexural strength were calculated. Good agreement is found between the experiments and FEA. It is shown that flexural modulus decreases with increasing percentage of S‐2 glass fibers, positive hybrid effects exist by substituting carbon fibers for glass fibers, and applying a thin layer of S‐2 glass fiber‐reinforced polymer on the compressive surface yields the highest flexural strength. The modeling approach presented will pave a way to the effective design of hybrid composites. POLYM. COMPOS., © 2012 Society of Plastics Engineers     

碳纤维布/玻纤布增强聚氨酯复合材料的研究

以聚氨酯为基体树脂,分别以碳纤维布、玻璃纤维布和这两种纤维布交替铺叠作为增强材料,采用真空辅助灌注成型工艺制备了4种复合材料.考察了纤维布的铺层结构对复合材料的弯曲、拉伸和冲击性能的影响.结果显示,复合材料的拉伸模量和弯曲模量随碳纤维含量增加而增加,冲击强度则降低.分别采用TGA、DMA和SEM对复合材料的热性能、界面...     

Study on mechanical properties of powder impregnated glass fiber reinforced poly(phenylene sulphide) by injection molding at various temperatures

The prepreg of continuous glass fiber reinforced poly(phenylene sulphide) (PPS) was prepared using the powder impregnation technique and cut into the pellets, in which the length of glass fibers was the same as the pellets. After injection molding, the mechanical properties were tested and the effects of the pellet length, fiber content, and thermal treatment on the mechanical properties at different temperatures were studied. It is found that the tensile strength and flexural strength of 6‐mm pellet sample are slightly higher than that of 3‐ and 12‐mm pellet samples. The tensile strength, flexural strength, and modulus decrease significantly with increasing the temperature. The notched Izod impact strength at 85ºC is higher than both at 25ºC and 205ºC. At 205ºC, the glass fiber reinforced PPS composites can still keep better mechanical properties. When the fiber content ranges from 0 to 50%, the mechanical properties increase with increasing the fiber contents at different temperatures, except the notched Izod impact strength do not further increase at 145 and 205ºC with raising the fiber content from 40 to 50%. Thermal treatment could improve the mechanical properties of the composites at higher serving temperature. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A comparative analysis of woven jute/glass hybrid polymer composite with and without reinforcing of fly ash particles

The objective of this research article is to compare the mechanical and tribological properties of jute‐glass‐fiber‐reinforced epoxy (J‐G‐E) hybrid composites with and without fly ash particulate filler. A dry hand lay‐up technique is used to fabricate all the laminates. The properties including flexural strength, tensile strength, flexural modulus, and erosion behavior of all the composites are evaluated as per American Society for Testing and Materials (ASTM) standards. The fly ash particulate‐filled hybrid composite shows a better mechanical and tribological property. The maximum flexural strength and flexural modulus are obtained for GJGJ+ 5 wt% fly ash filler epoxy composites. Whereas the maximum tensile strength is obtained for GJJG+ 10 wt% fly ash filler epoxy composites. Scanning Electron Microscopy (SEM) analysis also has been carried out to categorize mechanical and tribological behavior of composites. POLYM. COMPOS. 37:658–665, 2016. © 2014 Society of Plastics Engineers