Tuning the pKa of the antihistaminic drug chlorpheniramine maleate by supramolecular interactions with water-soluble polymers

The interaction of the pharmacologically important chlorpheniramine maleate (CPM) with polyanions containing sulfonate groups such as poly(sodium 4-styrenesulfonate) (PSS), poly(sodium vinylsulfonate) (PVS), and the more hydrophobic poly(sodium 2-(N-acrylamido)-2-methyl-propanesulfonate) (PAMPS) has been studied by ¹H NMR. It was found that the pK_a of the low-molecular weight molecule (LMWM) may be modified by its interaction with the polyanions, changing from 3 to 5, due to electric charge compensation. Interestingly, the interaction of CPM with PSS produces changes in CPM resonances, such as a general broadening and upfield shifts of the signals, and NOE effects between the LMWM and the water-soluble polymer (WSP) that indicate the presence of π-π interactions.     

π-Stacking of rhodamine B onto water-soluble polymers containing aromatic groups

Evidences of the π-stacking of rhodamine B onto poly(sodium 4-styrenesulfonate) are given by ¹H NMR spectroscopy. As a consequence of these π-π interactions, changes on the diafiltration and UV-vis absorbance and fluorescence patterns are shown comparing water-soluble polymers containing aromatic rings as poly(sodium 4-styrenesulfonate) and poly(N-methacryloyl-5-aminosalicylic acid) with other polyanions that do not contain aromatic rings as poly(sodium vinylsulfonate) and poly(acrylic acid).     

Fabrication and properties of reduced graphene oxide reinforced yttria-stabilized zirconia composite ceramics

Fully dense yttria-stabilized zirconia (YSZ) ceramics reinforced with reduced graphene oxide (RGO) were fabricated by spark plasma sintering (SPS), and their electrical, thermal, and mechanical properties were investigated. Graphene oxide (GO) was exfoliated by a short sonification in dimethylformamide (DMF)/water solution and uniformly mixed with ZrO₂ powders. The microstructure of the composites showed that undamaged RGO sheets were homogeneously distributed throughout matrix grains. The electrical conductivity of YSZ composites drastically increased with the addition of RGO, and it reached 1.2 × 10⁴ S/m at 4.1 vol.%. However, the thermal diffusivity increased only 12% with RGO addition. The hardness decreased slightly with RGO addition, whereas the fracture toughness significantly increased from 4.4 to 5.9 MPa^1/2. The RGO pull-out and crack bridging contributed to the improved fracture toughness.     

Synthesis of MnOx/reduced graphene oxide nanocomposite as an anode electrode for lithium-ion batteries

We report the high performance of the manganese oxide/reduced graphene oxide (MnOx/rGO) nanocomposite as an anode electrode of a lithium-ion battery. The composite is synthesized by a low temperature (83 °C) chemical solution reaction, and shows relatively high specific capacities (660 mAh g⁻¹) after 50 cycles. For MnOx/rGO composites, the cycling stability is increased remarkably as compared to that seen with individual MnOx, and this is due to the synergistic effects of both the components in the composite. The rGO acts as a conductive buffer layer that suppresses the volume change of MnOx, and simultaneously promotes the conductivity of MnOx. The functional groups of graphene oxide facilitate MnOx formation at low temperature, and this retains the MnOx-graphene oxide connection, thus improving the capacity and cycling stability.     

Easy preparation of ultrathin reduced graphene oxide sheets at a high stirring speed

This work explored the synthesis of rGO sheets from graphene oxide (GO) using hydrazine solvent as reducing agent through chemical reduction. Meanwhile, GO films with a 2D structure were prepared from graphite flakes (starting material with an average flake size of 150 nm) by an Improved Hummer׳s method. Results showed that the chemical oxidation of graphite flakes carried out at room temperature could be used to prepare GO sheets in the initial stage. The conversion of GO into large-area rGO sheets with ~85% of carbon content could then be achieved by chemical reduction. RGO sheets with a lateral dimension of up to ~45 nm were obtained, which indicated the formation of an extremely thin layer of rGO sheets. A high degree of GO reduction was also realized using a high stirring speed (1200 rpm) for 72 h in a mixture of acids and potassium permanganate, resulting in a high carbon content of rGO with a large lateral dimension and area. Overall, our Improved Hummer׳s method with a high stirring speed (1200 rpm) for 72 h provided an easy approach to the preparation of large-area and ultrathin rGO sheets.     

Green synthesis and synergistic catalytic effect ofAg/reduced graphene oxide nanocomposite

A nanocomposite of silver nanoparticles and reduced graphene oxide (Ag/rGO) has been developed as a catalyst for the reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) with sodium borohydride, owing to the larger specific surface area and synergistic effect of rGO. A facile and rapid microwave-assisted green route has been used for the uniform deposition of Ag nanoparticles and the reduction of graphene oxide simultaneously with l-arginine as the reducing agent. The resulting Ag/rGO nanocomposite contained about 51 wt% of Ag, and the Ag nanoparticles deposited on the surface of rGO had a mean diameter of 8.6 ± 3.5 nm. Also, the Ag/rGO nanocomposite exhibited excellent catalytic activity and stability toward the reduction of 4-NP to 4-AP with sodium borohydride. The reduction reaction obeyed the pseudo-first-order kinetics. The rate constants increased not only with the increase of temperature and catalyst amount but also with the increase of initial 4-NP concentration, revealing that the support rGO could enhance the catalytic activity via a synergistic effect. A mechanism for the catalytic reduction of 4-NP with NaBH₄ by Ag/rGO nanocomposite via both the liquid-phase and solid-phase routes has been suggested.     

CuxNi1-xO nanostructures and their nanocomposites with reduced graphene oxide: Synthesis,characterization, and photocatalytic applications

NiO nanostructure was synthesized using a simple co-precipitation method and was embedded on reduced graphene oxide surface via ultrasonication. Structural investigations were made through X-ray diffraction (XRD) and functional groups were confirmed by Fourier transform infrared spectroscopy (FTIR). XRD analysis revealed the grain size reduction with doping. Fourier transform infrared spectroscopy confirmed the presence of metal-oxygen bond in pristine and doped NiO nanostructure as well as the presence of carbon containing groups. Scanning electron microscopy (SEM) indicated that the particle size decreased when NiO nanostructure was doped with copper. BET surface area was found to increase almost up to 43 m²/g for Cu doped NiO nanostructure/rGO composite. Current-voltage measurements were performed using two probe method. UV–Visible spectroscopic profiles showed the blue and red shift for Cu doped NiO nanostructure and Cu doped NiO Nanostructure/rGO composite respectively. Rate constant for Cu doped NiO nanostructure/rGO composite found to increase 4.4 times than pristine NiO nanostructure.     

Nanocrystalline transition metal oxides and their composites with reduced graphene oxide and carbon nanotubes for photocatalytic applications

Transition metal oxide nanoparticles (CuO, ZnO & Fe₂O₃) and mixed metal oxides CuO. ZnO.Fe₂O₃ were fabricated by facile co-precipitation approach for photocatalytic treatment of organic dyes. The structural features, phase purity, crystallite size and morphology of individual and mixed metal oxides were analysed by X-rays diffraction patterns (XRD) and scanning electron microscopic (SEM) analysis. Electrical behaviour of CuO, ZnO, Fe₂O₃ and mixed metal oxides CuO. ZnO.Fe₂O₃ was explored by current-voltage (I-V) measurements. Functional groups present in the synthesized metal oxides were investigated by Fourier transform infrared spectroscopy (FTIR) which ensures the existence of M-O functional groups in the samples. The optical bandgap analysis was carried out by UV–visible spectroscopic technique which revealed that the blend of three different transition metal oxides reduced the bandgap energy of mixed metal oxides. The reason behind this reduced bandgap energy is formation of new electronic state which arises due to the metal-oxygen interactions. Moreover, the nanocomposites of CuO.ZnO.Fe₂O₃ with reduced graphene oxide (rGO) and carbon nanotubes (CNTs) were prepared to study the effect of the carbonaceous materials on the rate of photodegradation. These carbonaceous nanomaterials have plethora properties which can bring advancement in sector of photocatalytic treatment of wastewater. The photocatalytic experiments were performed using methylene blue (MB) as standard dye for comparative study of metal oxides and their composites with rGO and CNTs. The percentage degradation of methylene blue (MB) by nanocomposite CuO.ZnO.Fe₂O₃/rGO is 87% which is prominent among all samples. This result ascribed the photocatalytic aspects of reduced graphene oxide along with mixed metal oxides.     

Synthesis of manganese (IV) oxide at activated carbon on reduced graphene oxide sheets via laser irradiation technique for organic binder-free electrodes in flexible supercapacitors

We report a novel, green, scalable technique to synthesize binder-free, high-purity conductive composite comprising activated carbon (AC), manganese dioxide nanorods (MnO₂), and reduced graphene oxide sheets (rGO) for flexible supercapacitors with outstanding electrochemical performance. UV pulsed laser irradiation of GO-based composite dispersion (AC/GO or MnO₂@AC/GO) in ethanol aqueous medium was used to induce a photocatalytic reduction of GO and simultaneous anchor AC particles or AC loaded MnO₂ nanorods (MnO₂@AC) on the reduced GO sheets (rGO) at room temperature and atmospheric pressure. rGO sheets serve as a large surface area, conductive binder to enhance the ion adsorption, electrical conductivity, and mechanical flexibility of supercapacitor electrodes. This laser-induced photocatalytic reduction method was used to prepare two different rGO-based colloidal composites AC/rGO (CG) and MnO₂@AC/rGO (MCG). The prepared rGO-based colloidal composites were used to fabricate symmetric supercapacitors (CG//CG and MCG//MCG) and asymmetric supercapacitors (MCG//CG) in which MCG is the positive electrode and CG is the negative one. All prepared rGO-based supercapacitors demonstrated significant improvement in their electrochemical performance compared with rGO-free AC based supercapacitors. The enhancement in the electrochemical properties of rGO-based supercapacitors could be attributed to the intrinsic characteristics of rGO, such as high surface area, excellent electrical conductivity, and super mechanical flexibility. Our approach is a one-step, scalable, cost-effective synthesis technique to produce all binder-free AC/rGO based composites for flexible energy-storage devices.     

Synthesis of CuGeO3/reduced graphene oxide nanocomposite by hydrothermal reduction for high performance Li-ion battery anodes

Nowadays, Lithium-ion batteries (LIBs) are prevalently applied in numerous areas, leading to increasing demand of innovative electrodes with high specific capacities. An advanced CuGeO₃/reduced graphene oxide (rGO) structure is designed and fabricated as the anode material taking the advantage of considerable capacity offered by CuGeO₃ and stable framework constructed by rGO. The as-prepared CuGeO₃ with 30 wt% GO addition exhibits the best electrochemical performance. Specifically, a reversible charge capacity of 909 mAh·g⁻¹ with high coulombic efficiency of 91.49% at the current density of 100 mA g⁻¹ after 200 cycles is demonstrated, and the rate capacity retains 747.6 mAh·g⁻¹ with 91.59% capacity retention. These results indicate that the CuGeO₃/rGO composite holds great potential in next-generation LIBs.     

Investigations on pool boiling critical heat flux,transient characteristics and bonding strength of heater wire with aqua based reduced graphene oxide nanofluids

In the present work, the pool boiling critical heat flux, transient heat transfer characteristics, and bonding strength of thin Ni-Cr wire with aqua based reduced graphene oxide(r GO) nanofluids are experimentally studied. Results indicate:(i) the critical heat flux(CHF) of 0.01, 0.05, 0.1, 0.2, and 0.3 g·L~(-1) concentrations of r GO-water nanofluids varies from 1.42 to 2.40 MW·m~(-2);(ii) the CHF remains same for the tested samples during transient heat transfer studies and(iii) a constant value of CHF upto 10 tests when the nanocoated Ni-Cr wire is tested with DI water and deterioration occurs beyond this which implies a chance of peel off of r GO layer below the critical coating thickness.     

Hollow ZnSnO3 cubes@carbon/reduced graphene oxide ternary composite as anode of lithium ion batteries with enhanced electrochemical performance

The ternary composite, carbon coated hollow ZnSnO₃ (ZS@C) cubes encapsulated in reduced graphene oxide sheets (ZS@C/rGO), was synthesized via low-temperature coprecipitation and colloid electrostatic self-assembly. The uniform carbon-coating layer not only plays a role in buffering the volume change of ZnSnO₃ cubes in the charging/discharging processes, but also forms three-dimensional network with the cooperation of graphene to maintain the structural integrity and improve the electrical conductivity. The results show that the reduced graphene oxide sheets encapsulated ZS@C microcubes with a typical core-shell structure of ~700 nm in size exhibit an improved electrochemical performance compared with bare ZS@C microcubes. The ZS@C/rGO electrode delivered an initial discharge capacity of 1984 mA h g⁻¹ at a current density of 0.1 A g⁻¹ and maintained a capacity of 1040 mA h g⁻¹ after 45 cycles. High specific capacity and superior cycle stability indicate that the ZS@C/rGO composite has a great potential for the application of lithium-ion anode material.     

Ordered and ultrathin reduced graphene oxide LB films as hole injection layers for organic light-emitting diode

In this paper, we demonstrated the utilization of reduced graphene oxide (RGO) Langmuir-Blodgett (LB) films as high performance hole injection layer in organic light-emitting diode (OLED). By using LB technique, the well-ordered and thickness-controlled RGO sheets are incorporated between the organic active layer and the transparent conducting indium tin oxide (ITO), leading to an increase of recombination between electrons and holes. Due to the dramatic increase of hole carrier injection efficiency in RGO LB layer, the device luminance performance is greatly enhanced comparable to devices fabricated with spin-coating RGO and a commercial conducting polymer PEDOT:PSS as the hole transport layer. Furthermore, our results indicate that RGO LB films could be an excellent alternative to commercial PEDOT:PSS as the effective hole transport and electron blocking layer in light-emitting diode devices.     

Microwave-assisted green synthesis of Ag/reduced graphene oxide nanocomposite as a surface-enhanced Raman scattering substrate with high uniformity

A nanocomposite of silver nanoparticles/reduced graphene oxide (Ag/rGO) has been fabricated as a surface-enhanced Raman scattering (SERS) substrate owing to the large surface area and two-dimensional nanosheet structure of rGO. A facile and rapid microwave-assisted green route has been used for the formation of Ag nanoparticles and the reduction of graphene oxide simultaneously with L-arginine as the reducing agent. By increasing the cycle number of microwave irradiation from 1 and 4 to 8, the mean diameters of Ag nanoparticles deposited on the surface of rGO increased from 10.3 ± 4.6 and 21.4 ± 10.5 to 41.1 ± 12.6 nm. The SERS performance of Ag/rGO nanocomposite was examined using the common Raman reporter molecule 4-aminothiophenol (4-ATP). It was found that the Raman intensity of 4-ATP could be significantly enhanced by increasing the size and content of silver nanoparticles deposited on rGO. Although the Raman intensities of D-band and G-band of rGO were also enhanced simultaneously by the deposited Ag nanoparticles which limited the further improvement of SERS detection sensitivity, the detectable concentration of 4-ATP with Ag/rGO nanocomposite as the SERS substrate still could be lowered to be 10⁻¹⁰ M and the enhancement factor could be increased to 1.27 × 10¹⁰. Furthermore, it was also achievable to lower the relative standard deviation (RSD) values of the Raman intensities to below 5%. This revealed that the Ag/rGO nanocomposite obtained in this work could be used as a SERS substrate with high sensitivity and homogeneity.     

水热法制备还原氧化石墨烯及其导电性调控

导电性可调控的还原氧化石墨烯（rGO）在结构功能材料和化工新材料等领域具有重要的应用前景。本文利用水热还原法实现了rGO的绿色制备,并通过调控反应温度和时间,获得了电导率可控的rGO产品,其电导率范围为10^-4～1 S·cm^-1。采用UV-vis、FT-IR、XPS、SEM、XRD和Raman等表征方法系统研究了rGO还原过程中结构与组成的变化。发现GO还原过程中,其含氧官能团于120℃时开始明显分解,高于140℃后含量显著降低,GO片层sp2区域逐渐恢复,电导率逐渐增大到1 S·cm^-1,同时层间距从8.2 Å减少到3.6 Å（1 Å=0.1 nm）。对比热还原法,水热法有效避免了rGO片层的堆叠,产物分散性较好,有望规模化制备导电性可控的rGO产品。本研究成果对rGO生产和应用具有重要意义。     

Facile synthesis of Co0.5Zn0.5Fe2O4 nanoparticles decorated reduced graphene oxide hybrid nanocomposites with enhanced electromagnetic wave absorption properties

Herein, reduced graphene oxide/cobalt-zinc ferrite (RGO/Co_0.5Zn_0.5Fe₂O₄) hybrid nanocomposites were fabricated by a facile hydrothermal strategy. Results revealed that the contents of RGO could affect the micromorphology, electromagnetic parameters and electromagnetic wave absorption properties. As the contents of RGO increased in the as-synthesized hybrid nanocomposites, the dispersibility of the particles was improved. Meanwhile, numerously ferromagnetic Co_0.5Zn_0.5Fe₂O₄ particles were evenly anchored on the wrinkled surfaces of flaky RGO. Besides, the obtained hybrid nanocomposites exhibited superior electromagnetic absorption in both X and Ku bands, which was achieved by adjusting the RGO contents and matching thicknesses. Significantly, when the content of RGO was 7.4 wt%, the binary nanocomposites showed the optimal reflection loss of -73.9 dB at a thickness of 2.2 mm and broadest effective absorption bandwidth of 6.0 GHz (12.0–18.0 GHz) at a thin thickness of merely 2.0 mm. The enhanced electromagnetic absorption performance was primarily attributed to the multiple polarization effects, improved conduction loss caused by electron migration, and magnetic loss derived from ferromagnetic Co_0.5Zn_0.5Fe₂O₄ nanoparticles. Our results could provide inspiration for manufacturing graphene-based hybrid nanocomposites as high-efficient electromagnetic wave absorbers.     

Preparation and electrochemical properties of polyaniline/reduced graphene oxide composites

Polyaniline (PANI)/reduced graphene oxide (rGO) composites were synthesized by in situ oxidative polymerization of aniline on reduced graphene sheets. Fourier transform infrared spectroscopy, X‐ray diffraction, thermogravimetric analysis, transmission electron microscopy, and scanning electron microscopy were used to characterize the composites. The results indicated PANI/rGO composites were produced and contained covalent bonds between the functional groups of PANI and rGO. A uniform coating of PANI on the rGO sheets had a synergistic effect on the properties of the composites. The electrochemical properties of the PANI/rGO composites produced using different feed ratios of aniline to rGO were studied. The results showed that the composites exhibited a maximum specific capacitance of 797.5 F/g at 0.5 A/g and minimum charge transfer resistance of 0.98 Ω when the feed ratio of aniline to rGO was 2:1. These values were superior to those of pure PANI and rGO. The composites also displayed excellent cycling stability, with specific capacitance retention of 92.43% after 1000 cycles. These stable structural composites show promise for the development of new supercapacitor applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46103.     

Electrical conductivity of poly(3,4-ethylenedioxythiophene):p-toluene sulfonate films hybridized with reduced graphene oxide

Reduced graphene oxide-poly(3,4-ethylenedioxythiophene):p-toluene sulfonate (rGO-PEDOT:PTS) hybrid electrode films were synthesized directly on a substrate by interfacial polymerization between an oxidizing solid layer and liquid droplets of 3,4-ethylenedioxythiophene (EDOT) produced by electrospraying. The EDOT reduced the graphene oxide by donating electrons during its transformation into PEDOT:PTS, and hybrid films consisting of rGO distributed in a matrix of PEDOT:PTS were obtained. These rGO-PEDOT:PTS hybrid films showed excellent electrical conductivities as high as 1,500 S/cm and a sheet resistance of 70 Ω sq^-1. The conductivity values are up to 50% greater than those of films containing conductive PEDOT:PTS alone. These results confirm that highly conductive rGO-PEDOT:PTS hybrid films can potentially be used as organic transparent electrodes.     

Effects of graphene oxide and chemically reduced graphene oxide on the curing kinetics of epoxy amine composites

The curing kinetics of epoxy nanocomposites prepared by incorporating graphene oxide (GO) and chemically reduced graphene oxide (rGO) have been studied using isothermal and nonisothermal differential scanning calorimetry. The kinetic parameters of the curing processes in these systems have been determined by a Kamal and Sourour phenomenological model expanded by a diffusion factor. The predicted curves determined using the kinetic parameters fit well with the isothermal DSC thermograms revealing the proposed kinetic equation clearly explains the curing kinetics of the prepared epoxy amine nanocomposites. Experimental and modeling results demonstrate the presence of an accelerating effect of the GO on the cure of the resin matrix. The use of rGO instead of GO resulted in a slight acceleration reaction rate due to the reduced presence of oxidation groups in rGO. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44803.     

Microstructure,conductivity and mechanical properties of calcia stabilized zirconia ceramics obtained from nanosized precursor and reduced graphene oxide doped precursor powders

In the work 12CaO-88ZrO₂ (12CSZ, mol%) ceramics was manufactured both from nanopowder, obtained via cryochemical technique, and composite precursor 12CSZ?+?0.25?wt% rGO (reduced graphene oxide). Via SEM, XRD and Raman spectroscopy the detailed investigation of the effect of the precursor type and intermediate processing on the microstructure and electrical conductivity of ceramics was carried out. It was shown that rGO is completely removed during the annealing at 1550?°C for 3?h in air with no effect on the high ionic conductivity of ceramics. The use of nanosized powder and the additional processing step results in vacuum dense solid electrolytes characterized by well-formed cubic zirconia based solid solution, thin discontinuous grain boundaries and rather high ionic conductivity. The addition of rGO leads to slight microhardness (HV) decrease comparing to ceramics manufactured from the nanosized precursor. As a result, a new technique for zirconia based solid electrolytes having both high electrical conductivity at high temperatures and sufficient mechanical properties was suggested.