Insights into the simultaneous chronopotentiometric stripping measurement of indium(III), thallium(I) and zinc(II) in acidic medium at the in situ prepared antimony film carbon paste electrode

The simultaneous measurement of microgram per liter concentration levels of indium(III), thallium(I) and zinc(II) at the antimony film carbon paste electrode (SbF-CPE) is demonstrated. The antimony film was deposited in situ on a carbon paste substrate electrode and employed in chronopotentiometric stripping mode in deoxygenated solutions of 0.01 M hydrochloric acid (pH 2). The chronopotentiometric stripping performance of the SbF-CPE was studied and compared with constant current chronopotentiometric stripping and anodic stripping voltammetric operation. In comparison with its bismuth and mercury counterparts, the SbF-CPE exhibited advantageous electroanalytical performance; namely, at the bismuth film electrode, the measurement of zinc(II) was practically impossible due to hydrogen evolution, whereas the mercury film electrode exhibited a poorly developed signal for thallium(I). The SbF-CPE revealed favorable calculated LoDs (3σ) of 1.4 μg L⁻¹ for thallium(I) and 2.4 μg L⁻¹ for indium(III) along with good linear response in the examined concentration range from 10 to 100 μg L⁻¹ with correlations coefficients (R²) of 0.992 for thallium(I) and 0.994 for indium(III) associated with a 120 s deposition time. The chronopotentiometric stripping performance of the SbF-CPE was characterized also by satisfactory reproducibility of 1.62% for indium(III), 3.96% for thallium(I) and 2.11% for zinc(II) (c = 40 μg L⁻¹, n = 11).     

Electrochemical determination of bromide at a multiwall carbon nanotubes-chitosan modified electrode

A multiwall carbon nanotubes (MWNTs)-chitosan modified glassy carbon electrode (GCE) exhibits attractive ability for highly sensitive cathodic stripping voltammetric measurements of bromide (Br⁻). In pH 1.8 H₂SO₄ solution, a substantial increase in the stripping peak current of Br⁻ (compared to bare GCE and chitosan modified GCE) is observed using MWNTs-chitosan modified electrode. Operational parameters were optimized and the electrochemical behaviors of Br⁻ were studied by different electrochemical methods. The kinetics parameters were measured, the number of electron transfer (n) was 1 and the transfer coefficient (α) is 0.17. A wide linear calibration range (3.6 × 10⁻⁷-1.4 × 10⁻⁵ g mL⁻¹) was achieved, with a detection limit of 9.6 × 10⁻⁸ g mL⁻¹. The mechanism of electrode reaction was fully discussed.     

Enhanced mass transport to a reticulated vitreous carbon rotating cylinder electrode using jet flow

The mass transport characteristics of a porous, rotating cylinder electrode (RCE, 1.0 cm diameter; 0.5, 0.9 or 1.2 cm long; 1.25, 2.25, 3.00 cm³ overall volume; 250-2000 rpm speed) fabricated from reticulated vitreous carbon (RVC, 60 ppi or 100 ppi) were investigated. The deposition of copper from an acid sulfate electrolyte (typically, deoxygenated 1 mM CuSO₄ in pH 2, 0.5 M Na₂SO₄ at 298 K) was used as a test reaction. The effect of a jet flow of electrolyte towards the electrode and the introduction of polypropylene baffles in the electrochemical cell were studied at controlled rotation rates of the RCE. The product of mass transport coefficient and volumetric electrode area (k_mA_e) is related to the rotation speed of the electrode. For the 60 ppi RVC RCE, the jet electrolyte flow (3.5 cm³ s⁻¹) enhanced the mass transport rates by a factor of 1.46 at low rotation speeds; this factor was reduced to 1.08 at high rotation speeds. For a 100 ppi electrode, the enhanced mass transport decreased from 1.26 to 1.03 at low and high rotation rates, respectively. Under the experimental conditions, baffles showed little effect on the mass transport rates to the RVC RCE. Mass transport to jet flow at an RVC RCE is compared to other RCEs using dimensionless group correlation.     

Mass transport studies at rotating cylinder electrode: Influence of the inter-electrode gap

This study shows the effect of using two different inter-electrode gaps on the RCE mass transport characterization. The average mass transport coefficient was calculated using the limiting current technique, using the soluble reduction of triiodide (smooth RCE interface) and the copper deposition (roughness RCE interface) in KNO₃ and H₂SO₄, respectively. Based on the analysis of the Sh = aRe^bSc^0.356 correlation, the values of the constant a, associated with shape and cell dimensions, were 0.89 and 3.8, in the soluble system (I₃⁻/I⁻), for the gaps of 2.4 and 3.2 cm, respectively, indicating that this coefficient increases with inter-electrode space. While for copper deposition, these values were 0.00081 and 0.014, for the gaps of 2.4 and 3.2 cm. The constant b, associated with hydrodynamic regime, exhibits values of 0.43 and 0.33 for the gaps of 2.4 and 3.2 cm, respectively, in the system I₃⁻/I⁻, indicating that hydrodynamics on the smooth RCE diminishes according to the inter-electrode space. While for the system (Cu(II)/Cu), the values of b were 0.91 and 0.88, for the gaps of 2.4 and 3.2 cm. These values were higher for the copper deposition than for the soluble system, due to microturbulence at the roughened (and often powdery deposits) RCE interface. From the analysis performed in this paper is clear that inter-electrode gap and hydrodynamics on the smooth and roughness RCE interface (given by the nature of reduction reaction) modify the mass transport correlation.     

Electropolymerization of aniline in acid media on the bare and chemically pre-treated aluminum electrodes: A comparative characterization of the polyaniline deposited electrodes

The electrosynthesis of polyaniline on the bare aluminum and pre-treated aluminum surface achieved in aqueous H₂PtCl₆ solution saturated with NaF for few seconds is described. The effect of some factors such as pre-treatment time, aniline and sulfuric acid concentrations on the electropolymerization process was investigated and optimum conditions were obtained. The stability of polyaniline film on the pre-treated aluminum electrode (Al-Pt) was studied as function of the potential imposed on the electrode. For applied electrode potentials of 0.1-0.7 V, the first-order degradation rate constant, k, of polyaniline film varies between 1 × 10⁻⁶ and 2 × 10⁻⁵ s⁻¹, and a relatively low slope (i.e. 2.1) was obtained for the plot of log k versus E. The coatings were characterized by scanning electron microscopy (SEM), and cyclic voltammetric behavior of the polyaniline-deposited Al electrode (Al/PANI) and polyaniline-deposited Al-Pt electrode (Al-Pt/PANI) in 0.1 H₂SO₄ solutions is described. The electrocatalytic activity of the Al-Pt/PANI electrode against para-benzoquinone/hydroquinone (Q/H₂Q) and Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ redox systems was investigated and the obtained results are compared with those obtained on Al/PANI and bulk Pt electrodes.     

Synthesis and electrochemical performance of novel loose structured submicro/micro-sized NiSnx alloy composites for lithium batteries

An effective method of carbothermal reduction was employed to prepare spherical microcrystal NiSn_x alloy powders from oxides of Sn and Ni used as anode materials for Li-ion battery. According to XRD, SEM and TEM analysis, the synthesized spherical NiSn_x powders show a loose submicro/micro-sized structure and a multi-phase composition. The prepared NiSn_x alloy composite electrode exhibits a stable discharge capacity of electrode is ca. 380 mAh g⁻¹ at constant current density of 50 mA g⁻¹, and can be retained at 350 mAh g⁻¹ after 25 cycles. Moreover, NiSn_x alloys exhibit excellent high rate performance, i.e. stable discharge capacities of 300-310 mAh g⁻¹ and the coulombic efficiencies of 97.5-99.5% have been obtained at the current density of 500 mA g⁻¹. The loose submicro-sized particle structural characteristic and the Ni addition in Sn matrix should be responsible for the improvement of cycling stability of NiSn_x electrode. The carbothermal reduction method is simple, low-cost and mass-productive, which should be viable to other alloy composite materials system of rechargeable lithium ion batteries.     

Study and determination of the herbicide cyclosulfamuron by square wave stripping voltammetry

The voltammeric behavior of the herbicide cyclosulfamuron has been studied by square wave stripping voltammetry (SWSV). Cyclosulfamuron was reduced on a static mercury drop electrode (SMDE) and gave a well-defined peak in the pH range of 3.0-7.0. The peak potential (E_p) shifts to a more negative potential with increasing pH. The ratio ΔE_p/ΔpH over the pH range studied was 59.5 mV/pH. A systematic study of the various experimental parameters that affect the stripping response was studied by SWV. The square wave parameters used were a frequency of 150 Hz, an amplitude of −60 mV and a staircase step of 6.0 mV. The quantifications were performed by the standard addition method, from the SW voltammetric peak obtained at −1348 mV. Calibration curves were linear in the range of 10-350 μg L⁻¹ with a detection limit of 3.5 μg L⁻¹ under the conditions used (pH 6.0 buffer solution, E_acc = −400 mV vs. Ag/AgCl, t_acc = 75 s). The validity of the developed methodology was assessed by recovery experiments at the 25-100 μg L⁻¹ level. The mean results for 3 determinations were 49.7 ± 3.3 μg L⁻¹, which is very close to the amount of cyclosulfamuron added to soil (50 μg L⁻¹), with a recovery of 99.4%. The sufficiently good recoveries and low relative standard deviation (RSD) data reflects the high accuracy and precision of the proposed SW voltammetric method. The possible influences of various inorganic species and other pesticides were also investigated.     

Electrochemical tolazoline sensor based on gold nanoparticles and imprinted poly-o-aminothiophenol film

Amperometric detection of tolazoline (TL) was carried out on a gold nanoparticles (AuNPs)/poly-o-aminothiophenol (PoAT)-modified electrode by a molecular imprinting technique and electropolymerization method. The modification procedure was characterized via electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The recognition between the imprinted sensor and target molecule was observed by measuring the variation of amperometric response of the oxidation-reduction probe, K₃Fe(CN)₆ on electrode. Under the optimal experimental conditions, the peak currents were proportional to the concentrations of tolazoline in two ranges of 0.05-5.0 μg mL⁻¹ and 5.0-240 μg mL⁻¹ with the detection limit of 0.016 μg mL⁻¹. Meanwhile the prepared sensor showed sensitive and selective binding sites for tolazoline. The enhancement of sensitivity was attributed to the presence of AuNPs which decreased the electron-transfer impedance.     

Electrocatalytic oxidation of ascorbic acid by [Fe(CN)6] redox couple electrostatically trapped in cationic N,N-dimethylaniline polymer film electropolymerized on diamond electrode

Multinegatively charged metal complex, hexacyanoferrate ([Fe(CN)₆]⁴⁻), was electrostatically trapped in the cationic polymer film of N,N-dimethylaniline (PDMA) which was electrochemically deposited on the boron-doped diamond (BDD) electrode by controlled-potential electro-oxidation of the monomer. This ferrocyanide-trapped PDMA film was used to catalyze the oxidation of ascorbic acid (AA). Increase in the oxidation current response with a negative shift of the anodic peak potential was observed at the cationic PDMA film-coated BDD (PDMA|BDD) electrode, compared with that at the bare BDD electrode. A more drastic enhancement in the oxidation peak current as well as more negative shift of oxidation potential was found at the ferrocyanide-trapped PDMA film-coated BDD ([Fe(CN)₆]^3−/4−|PDMA|BDD) electrode. This [Fe(CN)₆]^3−/4−|PDMA|BDD electrode can be used as an amperometric sensor of AA. Ferrocyanide, electrostatically trapped in the polymer film shows more electrocatalytic activity than that coordinatively attached to the polymer film or dissolved in the solution phase. The electrocatalytic current depends on the surface coverage of ferricyanide, Γ_Fe, within the polymer film. Diffusion coefficient (D) of AA in the solution was estimated by rotating disk electrode voltammetry: D = (5.8 ± 0.3) × 10⁻⁶ cm² s⁻¹. The second-order rate constant for the catalytic oxidation of AA by ferricyanide was also estimated to be 9.0 × 10⁴ M⁻¹ s⁻¹. In the hydrodynamic amperometry using the [Fe(CN)₆]^3−/4−|PDMA|BDD electrode, a successive addition of 1 μM AA caused the successive increase in current response with equal amplitude and the sensitivity was calculated as 0.233 μA cm⁻² μM⁻¹.     

Determination of lithium diffusion coefficient in LiFePO4 electrode by galvanostatic and potentiostatic intermittent titration techniques

A new model of lithium-ion transport processes in the LiFePO₄ electrode is proposed. This model takes into account the phase transition LiFePO₄ ↔ FePO₄ accompanying reversible lithium intercalation into the electrode during potential or current steps. The diffusion coefficient of Li⁺ ion and its dependence on the LiFePO₄/FePO₄ phase ratio have been determined by means of processing of experimental potential and current transients in accordance with the model's equations. The results of galvanostatic and potentiostatic intermittent titration techniques are in good agreement. The value of diffusion coefficient varies within 10⁻¹⁰-10⁻¹⁶ cm² s⁻¹ depending on the lithium content in solid solution Li_XFePO₄ and Li_1−XFePO₄ (X < 0.02) or the LiFePO₄/FePO₄ phase ratio.     

Investigation of 30-cell solid oxide electrolyzer stack modules for hydrogen production

The 30-cell nickel-yttria stabilized zirconia (Ni-YSZ) hydrogen electrode-supported planar solid oxide electrolyzer (SOE) stack modules were manufactured and tested at 800 °C in steam electrolysis mode for hydrogen production. The electrolysis efficiency of the stack modules was higher than 100% at a total steam and hydrogen flow of 2.1 sccm cm⁻², a H₂O/H₂ ratio of 80/20, and a current density of <0.2 A cm⁻². The electrolysis efficiency, current efficiency, and actual hydrogen production rate of the stack modules increased with increasing H₂O/H₂ ratio at a constant current density. However, the electrolysis and current efficiencies decreased steadily at high current densities. During hydrogen production, the stack modules were operated at 800 °C and a constant current density of 0.15 A cm⁻² for up to 1100 h. A steam conversion rate of 62% and current efficiency of 87.4% were obtained; the actual hydrogen production rate reached as high as 103.6 N L h⁻¹. Post-mortem analysis showed that delamination of the LSM–YSZ oxygen electrode mainly occurred in the steam and air inlet area of the 10×10 cm² cells.     

Electrochemical characteristics of dopamine oxidation at palladium hexacyanoferrate film, electroless plated on aluminum electrode

A novel electrode material was obtained at an aluminum electrode (Al) by a simple electroless method including two consecutive procedures: (i) the electroless deposition of metallic palladium on the Al electrode surface from PdCl₂ + 25% ammonia solution and (ii) the chemical transformation of deposited palladium to the palladium hexacyanoferrate (PdHCF) films in a solution containing 0.5 M K₃[Fe(CN)₆]. The modified Al electrode demonstrated a well-behaved redox couple due to the redox reaction of the PdHCF film. The PdHCF film showed an excellent electrocatalytic activity toward the oxidation of dopamine (DA). The effect of solution pH on the voltammetric response of DA has been investigated. A linear calibration graph was obtained over the DA concentration range 2-51 mM. The rate constant k and transfer coefficient α for the catalytic reaction and the diffusion coefficient of DA in the solution D, were found to be 4.67 × 10² M⁻¹ s⁻¹, 0.63 and 2.5 × 10⁻⁶ cm² s⁻¹, respectively. The interference of ascorbic acid was investigated and greatly reduced using a thin film of Nafion on the modified electrode. The modified electrode indicated reproducible behavior and a high level stability during electrochemical experiments, making it particularly suitable for the analytical purposes.     

The ultrasonic electropolymerization of an 5-[o-(4-bromine amyloxy)phenyl]-10,15,20-triphenylporphrin (o-BrPETPP) film electrode and its electrocatalytic properties to dopamine oxidation in aqueous solution

5-[o-(4-Bromine amyloxy)phenyl]-10,15,20-triphenylporphrin (o-BrPETPP) was electropolymerized on a glassy carbon electrode (GCE), and the electrocatalytic properties of the prepared film electrode response to dopamine (DA) oxidation were investigated. A stable o-BrPETPP film was formed on the GCE under ultrasonic irradiation through a potentiodynamic process in 0.1 M H₂SO₄ between −1.1 V and 2.2 V versus a saturated calomel electrode (SCE) at a scan rate of 0.1 V s⁻¹. The film electrode showed high selectivity for DA in the presence of ascorbic acid (AA) and uric acid (UA), and a 6-fold greater sensitivity to DA than that of the bare GCE. In the 0.05 mol L⁻¹ phosphate buffer (pH 6.0), there was a linear relationship between the oxidation current and the concentration of DA solution in the range of 5 × 10⁻⁷ mol L⁻¹ to 3 × 10⁻⁵ mol L⁻¹. The electrode had a detection limit of 6.0 × 10⁻⁸ mol L⁻¹(S/N = 3) when the differential pulse voltammetric (DPV) method was used. In addition, the charge transfer rate constant k = 0.0703 cm s⁻¹, the transfer coefficient α = 0.709, the electron number involved in the rate determining step n_α = 0.952, and the diffusion coefficient D_o = 3.54  10⁻⁵ cm² s⁻¹ were determined. The o-BrPETPP film electrode provides high stability, sensitivity, and selectivity for DA oxidation.     

Treatment of olive mill wastewater by the combination of ultrafiltration and bipolar electrochemical reactor processes

The main purpose of this study was to investigate the removal of the chemical oxygen demand (COD) from olive mill wastewater (OMW) by the combination of ultrafiltration with electrocoagulation process. Ultrafiltration process equipped with CERAVER membrane was used as pre-treatment for electrochemical process. The obtained permeate from the ultrafiltration process allowed COD removal efficiency of about 96% from OMW. Obtained permeate with an average COD of about 1.1 g dm⁻³ was treated by electrochemical reactor equipped with a reactor with bipolar iron plate electrodes. The effect of the experimental parameters such as current density, pH, surface electrode/reactor volume ratio and NaCl concentration on COD removal was assessed. The results showed that the optimum COD removal rate was obtained at a current density of 93.3 A m⁻² and pH ranging from 4.5 to 6.5. At the optimum operational parameters for the experiments, electrocoagulation process could reduce COD from 1.1 g dm⁻³ to 78 mg dm⁻³, allowing direct discharge of the treated OMW as that meets the Algerian wastewater discharge standards (<125 mg dm⁻³).     

A novel micro-spherical CoSn2/Sn alloy composite as high capacity anode materials for Li-ion rechargeable batteries

Micro-scaled spherical CoSn₂/Sn alloy powders synthesized from oxides of Sn and Co via carbothermal reduction at 800 °C were examined for use as anode materials in Li-ion battery. The phase composition and particle morphology of the CoSn₂/Sn alloy composite powders were investigated by XRD, SEM and TEM. The prepared CoSn₂/Sn alloy composite electrode exhibits a low initial irreversible capacity of ca. 140 mAh g⁻¹, a high specific capacity of ca. 600 mAh g⁻¹ at constant current density of 50 mA g⁻¹, and a good rate capability. The stable discharge capacities of 500-515 mAh g⁻¹ and the columbic efficiencies of 95.8-98.1% were obtained at current density of 500 mA g⁻¹. The relatively large particle size of CoSn₂/Sn alloy composite powder is apparently favorable for the lowering of initial capacity loss of electrode, while the loose particle structural characteristic and the Co addition in Sn matrix should be responsible for the improvement of cycling stability of CoSn₂/Sn electrode.     

Anodic stripping voltammetric measurement of trace heavy metals at antimony film carbon paste electrode

The antimony film carbon paste electrode (SbF-CPE) was prepared in situ on the carbon paste substrate electrode as a “mercury-free” electrochemical sensor. Its aptitude for measuring some selected trace heavy metals has been demonstrated in combination with square-wave anodic stripping voltammetry in non-deaerated model solutions of 0.01 M hydrochloric acid with pH 2. Some important operational parameters, such as deposition potential, deposition time, and concentration of antimony ions were optimized, and the electroanalytical performance of the SbF-CPE was critically compared with both bismuth film carbon paste electrode (BiF-CPE) and mercury film carbon paste electrode (MF-CPE) using Cd(II) and Pb(II) as test metal ions. In comparison with BiF-CPE and MF-CPE, the SbF-CPE exhibited superior electroanalytical performance in more acidic medium (pH 2) associated with favorably low hydrogen evolution, improved stripping response for Cd(II), and moreover, stripping signals corresponding to Cd(II) and Pb(II) at the SbF-CPE were slightly narrower than those observed at bismuth and mercury counterparts. In addition, the comparison with antimony film electrode prepared at the glassy carbon substrate electrode displayed higher stripping current response recorded at the SbF-CPE. The newly developed sensor revealed highly linear behavior in the examined concentration range from 5 to 50 μg L⁻¹, with limits of detection (3σ) of 0.8 μg L⁻¹ for Cd(II), and 0.2 μg L⁻¹ for Pb(II) in connection with 120 s deposition step, offering good reproducibility of ±3.8% for Cd(II), and ±1.2% for Pb(II) (30 μg L⁻¹, n = 10). Preliminary experiments disclosed that SbF-CPE and MF-CPE exhibit comparable performance for measuring trace concentration levels of Zn(II) in acidic medium with pH 2, whereas its detection with BiF-CPE was practically impossible. Finally, the practical applicability of SbF-CPE was demonstrated via measuring Cd(II) and Pb(II) in a real water sample.     

Evaluation of the photoelectrocatalytic method for oxidizing chloride and simultaneous removal of microcystin toxins in surface waters

The production of chlorine was investigated in the photoelectrocatalytic oxidation of a chloride-containing solution using a TiO₂ thin-film electrode biased at current density from 5 to 50 mA cm⁻² and illuminated by UV light. Such parameters as chloride concentrations from 0.001 to 0.10 mol L⁻¹, pH 2-12, and interfering salts were varied in this study in order to determine their effect on this oxidation process. At an optimum condition this photoelectrocatalytic method can produce active chlorine at levels compatible to water disinfections processes using a chloride concentration higher than 0.010 mol L⁻¹ at a pH of 4 and a current density of 30 mA cm⁻². The method was successfully applied to treat surface water collected from a Brazilian river. After 150 min of photoelectrocatalytic oxidation, we obtained a 90% reduction in total organic carbon removal, a 100% removal of turbidity, a 93% decrease in colour and a chemical oxygen demand (COD) removal of around 96% (N = 3). The proposed technology based on photoelectrocatalytic oxidation was also tested in treating 250 mL of a solution containing 0.05 mol L⁻¹ NaCl and 50 μg L⁻¹ of Microcystin aeruginosa. The bacteria is completely removed after 5 min of photoelectrocatalysis following an initial rate constant removal of −0.260 min⁻¹, suggesting that the present method could be considered as a promising alternative to chlorine-based disinfections.     

Electrochemical polymerization and initial corrosion properties of polyaniline-benzoate film on aluminum

Electrochemical synthesis of polyaniline (PANI) on aluminum electrode from aqueous solution of 0.25 mol dm⁻³ aniline and 0.2 mol dm⁻³ sodium benzoate has been investigated under potentiodynamic and galvanostatic conditions. Initial corrosion behavior of aluminum and PANI coated aluminum electrode exposed to 3% NaCl has been investigated using electrochemical potentiodynamic and impedance spectroscopy technique (EIS). It was shown that PANI coating initially provide corrosion protection of aluminum, decreasing the corrosion current density at least 15 times.     

Electroless immobilization and electrochemical characteristics of nickel hexacyanoruthenate film at an aluminum substrate

The surface of an aluminum (Al) electrode was modified with a thin film of nickel hexacyanoruthenate (NiHCR) as a novel electrode material. The modification procedure of Al surface, includes two consecutive procedures: (i) the electroless deposition of metallic nickel on the Al electrode surface from NiCl₂ solution, and (ii) the chemical transformation of deposited nickel to nickel hexacyanoruthenate films in solution of 20 mM K₃[Ru(CN)₆] + 0.5 M KNO₃. Cyclic voltammogram of the modified Al electrode showed a well-defined redox reaction due to [Ni^IIRu^III/II(CN)₆]^1−/2− system. The effects of different supporting electrolytes and solution pH were studied on the electrochemical characteristics of the modified electrode. The diffusion coefficients of K⁺ and Na⁺ cations in the film (D), the transfer coefficient (α), and the charge transfer rate constant at the modifying film/electrode interface (k_s), were calculated in the presence of both K⁺ and Na⁺ cations. The stability of the modified electrode was investigated under various experimental conditions.