Sweet aqueous solution for electrochemical synthesis of polypyrrole: Part 2. On ferrous metals

The electrochemical synthesis of polypyrrole on iron has been fruitfully achieved in aqueous medium of sodium saccharinate and pyrrole. The obtained coating under these conditions has been reached with cyclic voltammetry and chronomethods. The applied current density has a great effect on the thickness of PPy electrodeposited on iron electrodes. The characterization techniques show a good homogeneity of the PPy coating. The corrosion behaviour of PPy/Fe was investigated in sodium chloride by linear polarization, electrochemical impedance spectroscopy, and weight loss. The results show that PPy coating electrodeposited could provide a good protection against corrosion.     

Inhibition of corrosion of mild steel by homopolymer and bilayer coatings of polyaniline and polypyrrole

Homopolymers and bilayers of polyaniline (PAni) and polypyrrole (PPy) coatings have been electropolymerized on mild steel by potentiodynamic synthesis technique in aqueous oxalic acid solutions. Characterization of coatings was carried out by cyclic voltammetry. Corrosion behavior of the polymer coated mild steel electrodes was investigated using linear anodic potentiodynamic polarization, Tafel test and electrochemical impedance spectroscopy (EIS) techniques in various aqueous corrosive solutions. Corrosion test results clearly showed that PPy and PAni/PPy bilayer coatings served as a stable host matrix on mild steel against corrosion. However, bilayers of PAni and PPy did not exhibit good combined properties of each polymer, unlike expected. PPy exhibited the best corrosion resistance among all coatings.     

Electrochemical synthesis of polypyrrole (PPy) and PPyǀmetal composites on copper electrode and investigation of their anticorrosive properties

This study reports corrosion protection behaviour of various metal cations electrodeposited onto polypyrrole (PPy) coated copper (Cu) electrode. Before electropolymerization of pyrrole, the Cu electrode was passivated in 0.1 M oxalic acid via cyclic voltammetry method. After the coating process, metal cation electrodeposition onto PPy coating was carried out in 10⁻² M CuCl₂, ZnCl₂, FeCl₂ and NiCl₂ solutions. Corrosion behaviour of uncoated, PPy and PPy|metal coated Cu electrodes was studied in 0.1 M H₂SO₄ solution by using potentiodynamic polarization, chronoamperometric and impedance spectroscopic measurements. Surface morphologies were examined by scanning electron microscope (SEM). All the electrochemical measurements were in good agreement showing that metal electrodeposited PPy coated Cu electrodes have a higher corrosion resistance. Furthermore, SEM results show that while all the samples have a homogeneous distribution of metal cations, zinc and nickel have a much better homogeneous distribution compared to copper and iron. It was found that the best corrosion protection is provided by PPy|Zn and PPy|Ni coatings and there is a significant increase in their polarization resistance with increasing amounts of electrodeposited cations.     

Characterization and corrosion protection properties of polypyrrole / montmorillonite electropolymerized onto aluminium alloy 1100

Films of Polypyrrole/Montmorillonite (PPy/MT) clays were electropolymerized potentiostatically on aluminium alloy 1100, using sodium dodecylbenzenesulfonate (SDBS) as a dopant. Two clay species were used: Na⁺-Montmorillonite (MT-Na) and modified-Montmorillonite (MT-M). The characterization of the PPy/MT films performed by XRD and TEM shows that the exfoliation method employed, as well the electrochemical polymerization method used in this work, allow nanocomposite materials to be obtained. The PPy/MT films were found to have less electrical conductivity than pure PPy. The corrosion protection of aluminium alloy 1100 covering PPy/MT was evaluated by electrochemical techniques in 0.05 mol L⁻¹ NaCl medium. The electrochemical parameters derived from the polarization curves, together with the EIS data, revealed that the corrosion resistance of PPy/clay coatings depends on the type and concentration of Montmorillonite employed. The best performance in the corrosion protection of the aluminum was achieved with PPy/MT films containing 1% of clay.     

Sweet aqueous solution for electrochemical synthesis of polypyrrole part 1B: On copper and its alloys

The electrochemical synthesis of polypyrrole (PPy) on copper and brass has been successfully achieved in sodium saccharinate and pyrrole aqueous medium. The synthesized coating under several electrochemical techniques such as cyclic voltammetry, galvanostatic and potentiostatic is homogeneous and adherent. PPy has been characterized by SEM, XPS, IR and Raman spectroscopy and its quality has been confirmed. The doping level obtained from N 1s XPS signal of the oxidized PPy depends on the electrochemical technique used to produce the film. The corrosion performance of PPy/copper and PPy/brass has been evaluated in 3% NaCl and 0.1 M HCl using linear polarization and electrochemical impedance spectroscopy. The results show that PPy coating electrodeposited from sodium saccharinate exhibits significant corrosion protection properties.     

Hierarchical polymer nanocomposite coating material for 316L SS implants: Surface and electrochemical aspects of PPy/f-CNTs coatings

Biocompatible nanocomposite coatings can be synthesized to offer improved surface properties for biomaterials and biomedical implants. Nanocomposite coatings containing polypyrrole (PPy) matrix reinforced with functionalized multi-wall carbon nanotubes (f-CNTs) were deposited on 316L SS substrates using electrochemical route. FT-IR, XRD, SEM, and TEM were employed to characterize the nanocomposite microstructure. High resolution imaging showed relatively uniform dispersion of the CNTs in the nanocomposite with a typical tubular structure. Micro-indentation tests revealed improvement in the hardness of the PPy/CNTs coatings. Measurement of the contact angle indicated enhanced surface wettability of the nanocomposite coatings. The corrosion behavior of 316L SS samples coated with PPy/CNTs was studied in SBF medium. The corrosion potential and the breakdown potential of coated 316L SS substrates shifted to more noble values as compared to uncoated 316L SS samples. The results suggest that incorporating CNTs as reinforcements in PPy coatings can provide enhanced properties in terms of surface hardness, biocompatibility, and corrosion resistance.     

The corrosion protection of mild steel by single layered polypyrrole and multilayered polypyrrole/poly(5-amino-1-naphthol) coatings

Electrochemical synthesis of polypyrrole (PPy) and top coat of poly(5-amino-1-naphthol) (PANAP) on PPy films from oxalic acid solution was achieved on mild steel (MS) by cyclic voltammetry technique. The morphology and the structure of the films were investigated by scanning electron microscopy (SEM). The corrosion performance of this multilayer coating and single PPy coating were investigated in 3.5% NaCl solution by using open circuit potential (E_ocp)–time curves, polarization curves and electrochemical impedance spectroscopy (EIS). It was found that the multilayer PPy/PANAP coating could provide much better protection than single PPy coating for corrosion of MS. It was observed that corrosion performance of coatings was increasing with immersion period. This was explained by auto-undoping properties of PPy coatings during immersion in corrosive solution. The improved corrosion performance in the presence of PANAP top coat on PPy was explained by increase in barrier effect of bilayer films.     

Optimization of electrochemical polymerization parameters of polypyrrole on Mg–Al alloy (AZ91D) electrodes and corrosion performance

We report on the optimum electropolymerization conditions of polypyrrole (PPy) coatings on Mg alloy AZ91D electrodes from aqueous electrolytes of sodium salicylate via cyclic voltammetry (CV). Results show that initial and end potential values during the electrochemical coating procedure play an important role on the adhesion and corrosion performance of PPy films. Corrosion tests of AZ91D electrodes coated with PPy under optimized conditions show a good corrosion performance during 10 days in Na₂SO_4, without peeling off of these thin films.     

Electrodeposition of polypyrrole on aluminium in aqueous tartaric solution

The electrosynthesis of polypyrrole (PPy) has been achieved on aluminium in aqueous medium of tartaric acid by means of cyclic voltammetry, potentiostatic and galvanostatic techniques. Scanning electron microscopy (SEM) and X-ray microanalysis by energy spectroscopy dispersion (EDS) applying on surfaces show that the PPy coating is developed from the metal surface through the cracks of the initial Al₂O₃ layer.A mechanism involving the participation of the supporting electrolyte and the pyrrole (Py) in distinct active sites was proposed based on the linear sweep voltammetry. It is observed for all applied electrochemical techniques that the pyrrole concentration has to be higher than 0.1 M to allow the polypyrrole electrodeposition in acid medium.Scanning electron microscopy, secondary electrons (SE) and backscattering electrons (BE), shows that the PPy coating obtained in galvanostatic and potentiostatic modes starts with small islands at weak applied potentials or current densities. Moreover, EDS reveals a good homogeneity and compactness of the film achieved in galvanostatic method. The corrosion results in 3% NaCl medium show that the PPy coating decreases the corrosion behaviour of the aluminium. The bilayer Al₂O₃/PPy shows a capacitor with future applications.     

Evaluation of corrosion resistance of polypyrrole/functionalized multi-walled carbon nanotubes composite coatings on 60Cu–40Zn brass alloy

Polypyrrole/multi-walled carbon nanotubes (PPy/MWCNT) and its carboxylic functionalized (PPy/MWCNT-COO⁻) composite films were successfully electropolymerized by cyclic voltammetry as protective coating against corrosion on 60Cu–40Zn brass alloy surface. It yielded to strongly adherent and smooth nanocomposite films. Kinetics of the corrosion protection was investigated in 3.5 wt% NaCl solutions by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization tests. The results showed that the presence of MWCNT in PPy coat considerably reduces the corrosion rate of 60Cu–40Zn brass alloy. The enhanced inhibition is most likely due to interaction between MWCNT and PPy. This in turn, improves the alloy passivation improvement and alters the permselectivity of the coating from anionic selectivity to the cationic selectivity. Moreover, PPy/MWCNT-COO⁻ functionalized nanocomposite provided higher corrosion resistance coating than PPy/MWCNT alone.     

Sweet aqueous solution for electrochemical synthesis of polypyrrole: Part 1-A. On non-ferrous metals

The electrosynthesis of polypyrrole (PPy) has been achieved on aluminum electrode in aqueous medium of 0.1 M saccharin sodium salt and 0.5 M pyrrole. Scanning electron microscopy shows that the PPy coating obtained in galvanostatic and potentiostatic modes starts with small islands at weak applied potentials or current densities. Moreover, energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) reveal a good homogeneity of the film achieved in cyclic voltammetry during 10 cycles. The electrochemical impedance spectroscopy (EIS) results show that the coating decreases the polarization resistance of the aluminum electrode. The open circuit potential (OCP) and dc polarization measurements achieved in HCl and NaCl solutions displayed a large positive displacement of corrosion potential and a reduction of corrosion current in the case of PPy coating electrode in comparison with electrode bare.     

Comparison of the corrosion protection of mild steel by polypyrrole–phosphate and polypyrrole–tungstenate coatings

The electrodeposition of polypyrrole–phosphate (PPy–P) and polypyrrole–tungstenate (PPy–W) on mild steel (MS) were achieved in an oxalic acid medium with cyclic voltammetry techniques. Adherent and homogeneous PPy–P and PPy–W films were obtained. The corrosion behavior of mild steel with phosphate (PPy–P) and tungstenate (PPy–W) composite coatings in 3.5% NaCl solutions were investigated through a potentiodynamic polarization technique, open‐circuit potential–time curves, and electrochemical impedance spectroscopy (EIS). On the basis of a physical model for corrosion of mild steel composites, Zview (II) software was applied to the EIS to estimate the parameters of the proposed equivalent circuit. It was found that the PPy–W coatings could provide much better protection than the PPy–P and polypyrrole coatings. The effects of the phosphate and tungstenate process parameters on the morphology and structure of the passive films were investigated by scanning electron microscopy and electron dispersion X‐ray analyses. The results reveal that the PPy–P and PPy–W coated electrodes offered a noticeable enhancement in protection against corrosion processes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of benzotriazole (BTA) addition on Polypyrrole film formation on copper and its corrosion protection

Benzotriazole (BTA) was added in a conducting Polypyrrole (PPy) film prepared on copper in oxalic acid aqueous solution containing pyrrole monomer to improve corrosion protection by the PPy film and reduce copper corrosion. When BTA was added in the preparation solution, the copper surface was covered by a BTA–Cu complex layer before the anodic polymerization of PPy was started. On the copper surface with the BTA layer, the initial dissolution of copper was inhibited and the PPy polymerization-deposition was started immediately after the anodic current was imposed. The PPy film thus formed was doped with oxalic ions and ionized BTA and was homogeneous in thickness and strongly adhesive. The PPy film containing BTA protected the copper from corrosion in 3.5 wt.% NaCl solution. In 400 h of immersion, copper dissolution was inhibited with 80% protection efficiency relative to that of bare copper.     

Copper/polypyrrole multilayer coating for 7075 aluminum alloy protection

The corrosion behavior of 7075 aluminum (Al), copper modified Al (Al/Cu), polypyrrole modified Al (Al/PPy) and copper (under layer)/polypyrrole (top layer) modified Al (Al/Cu/PPy) samples were investigated in 3.5% NaCl solution. The copper plating on aluminum was carried out from acidic copper sulphate solution by electroless method. Polypyrrole (PPy) was electrochemically synthesized on Al and Al/Cu electrodes from 0.1 M pyrrole containing 0.4 M oxalic acid solution using cyclic voltammetry technique. The films synthesized were characterized by Fourier transform infrared spectroscopy (FT-IR). The thermal stability of PPy films was investigated by thermogravimetric analysis (TGA). The surface morphologies were examined by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The corrosion behavior of samples was investigated by electrochemical impedance spectroscopy (EIS) and anodic polarization curves. The data obtained showed that the synthesis of PPy on top of the Cu layer significantly enhances the corrosion resistance of Al by exhibiting a barrier effect against the attack of corrosive environment.     

Improvement of polypyrrole films for corrosion protection of zinc-coated AZ91D alloy

To improve the protection against the corrosion of AZ91D magnesium alloy provided by conducting polypyrrole (PPy) films, optimization of the electrochemical synthesis of the PPy film was investigated. The bi-layered PPy film was prepared under constant current control, first in a sodium tartrate solution containing molybdate and second in a sodium dodecylsulfate (DS) solution (after the AZ91D alloy was covered by zinc electroplating). Corrosion testing of the zinc-coated AZ91D alloy covered with the PPy film was performed in 3.5% NaCl solution. The more protective PPy film doped with tartrate ions (PPy-Tart film) was formed by the lower current density (CD). Doping of molybdate ions (MoO₄²⁻) into the PPy-Tart film significantly improved its corrosion protection properties. When the PPy-Tart-MoO₄ layer was covered by an outer PPy layer doped with DS ions, the corrosion protection was further improved. The imposition of ultrasonic waves during the electropolymerization of the inner PPy-Tart-MoO₄ layer was effective in the improvement of corrosion protection. The bi-layered PPy-Tart-MoO₄/PPy-DS film prepared under ultrasonic irradiation maintained the zinc-coated AZ91D alloy in the passive state during the corrosion test in NaCl solution for 221 h, during which no corrosion products appeared.     

Polypyrrole coatings for corrosion protection of Al alloy2024: influence of electrodeposition methods,solvents, and ZnO nanoparticle concentrations

Since ZnO nanoparticles increase the electrical conductivity of the polypyrrole (PPy) coatings, an investigation was carried out to evaluate the effect of ZnO nanoparticles loading on the corrosion protection performance of PPy coatings on AA2024 Al alloy in 3.5% NaCl solution. At first, some measurements were carried out to find the best experimental conditions containing the electrodeposition method, electrosynthesis solvent composition, and ZnO nanoparticles’ concentration for preparing the optimum PPy coating on Al alloy2024. Three different methods of electrodeposition, namely: cyclic voltammetry, galvanostatic, and potentiostatic techniques were analyzed. The anti-corrosion performance of the PPy coatings was evaluated by electrochemical impedance spectroscopy and Tafel polarization methods. The PPy prepared by potentiostatic method exhibited the best performance against corrosion of Al alloy2024 in 3.5% NaCl solution. Then, different mixtures of H₂O/ethanol were tested as electrosynthesis solvents for preparation of PPy coatings on the alloy by optimized electrodeposition mode (i.e., potentiostatic). In evaluation of the prepared coatings, the pure water was introduced as the optimum solvent in electrodeposition of PPy. The investigation of different ZnO nanoparticles’ concentrations proved that the PPy coating containing 0.025% ZnO nanoparticles was the optimum coating against the corrosion of Al alloy in NaCl solution. Finally, the long-term evaluation of the corrosion protection performance of the coatings revealed that the optimum coating provided suitable protection against corrosion up to 14 days after immersion.

     

Influence of pH on the synthesis and properties of polypyrrole on copper from phytic acid solution for corrosion protection

Polypyrrole (PPy) films were deposited on copper from “green” inhibitor of phytic acid solution for corrosion protection of copper. The corrosion protection property of the PPy layer was studied by an immersion test in a NaCl aqueous solution. The polymerization process of PPy on copper changed with the pH values of phytic acid solution and current density applied. When one oxidized bare copper in phytic acid solution at various pHs containing pyrrole monomer, a thin layer consisting of complex compound of Cu-phytate was firstly formed, followed by the formation of the PPy layer doped with phytate anion on the complex compound layer. The complex compound layer passivated the copper surface and its thickness increased with the lower pH value of the solution and the lower current density applied. It was found that the PPy coating prepared in the phytic acid solution at pH 4 exhibit the most protective property against copper corrosion.     

Improvement of the anticorrosion properties of polypyrrole by zinc phosphate pigment incorporation

A commercial zinc phosphate pigment was incorporated into polypyrrole (PPy) matrix during its electrochemical synthesis in order to improve the corrosion protection of polypyrrole on AISI 1010 steel. PPy/zinc phosphate composite films were synthesised in sodium salicylate medium with high current efficiency and containing 10% by weight of zinc and 4% by weight of phosphate. The influence of stirring and concentration of the electrolyte on the degree of pigment incorporation were investigated, as well as polymerisation time and applied current density. The morphology of the films was determined by scanning electron microscopy (SEM) and the distribution of pigment in the polymeric matrix was carried out by X-ray photoelectron spectroscopy (XPS). The PPy and PPy/zinc phosphate films were submitted to salt spray corrosion test, weight loss test and to electrochemical measurements like corrosion potential with time. In all tests, the composite films showed an enhancement in its protective action in comparison with PPy films.     

Effect of doping by corrosion inhibitors on the morphological properties and the performance against corrosion of polypyrrole electrodeposited on AA6061-T6

This paper describes the electrosynthesis of polypyrrole (PPy) onto AA6061-T6 aluminum alloy from a sulfuric acid solution doped with molybdate anions (MoO₄²⁻) or 8-hydroxyquinoline (8HQ) species. These dopant compounds were chosen as they have been proven to be effective in mitigating the corrosion in chloride medium. The protectiveness of PPy coatings incorporating these corrosion inhibitors within the polymer matrix is discussed. The coatings were morphologically characterized via scanning electron microscopy (SEM) and evaluated electrochemically via polarization in 0.5 M NaCl. The results show that doping PPy with molybdates or 8HQ changes its morphological properties and its effectiveness in preventing passivity loss for AA6061-T6 in chloride media.     

Highly transparent and organosoluble polyimides derived from 2,2′‐disubstituted‐4,4′‐oxydianilines

Polypyrrole (PPy) and Polypyrrole‐ZnO (PPy‐ZnO) nanocomposites were electrodeposited on mild steel and its corrosion protection ability was studied by Tafel and Impedance techniques in 3.5% NaCl solution. Pure Polypyrrole film was not found to protect the mild steel perfectly but the coating with nano‐sized ZnO (PPy‐ZnO) has dramatically increased the corrosion resistance of mild steel. Electrochemical Impedance Spectroscopy (EIS) measurements indicated that the coating resistance (R_coat) and corrosion resistance (R_corr) values for the PPy‐ZnO nanocomposite coating was much higher than that of pure PPy coated electrode. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011