Chemical Stability of ZnO–Na2O–SO3–P2O5 Glasses

We report on chemical stability and corrosion behavior of highly depolymerized sulfophosphate glasses from the system ZnO–Na₂O–SO₃–P₂O₅ in aqueous solution, providing data on weight loss, ion release rates, and modifications of surface topology as a function of time, temperature and pH value. Observations seem consistent with the previously developed structural model of chemical heterogeneity, where cations Na⁺ and Zn²⁺ cluster selectively in the vicinity of sulfate and phosphate anions, respectively.     

Surface and bulk crystallization in Nd2O3–Al2O3–SiO2–TiO2 glasses

Neodymium aluminosilicate (Nd₂O₃–Al₂O₃–SiO₂; NdAS) glasses have been investigated for the effect of concentration of TiO₂ on the crystallization mechanism and for the effect of surface condition on crystal growth. NdAS glasses with 0–10 wt.% TiO₂ were heat-treated for nucleation and crystal growth and were examined for phase separation and morphology of surface crystals as well as for crystal growth rate. All the glasses exhibit surface crystallization, however, the glass having 8 wt.% TiO₂ also exhibits internal crystallization after a two-stage heat treatment. Surface crystallization was dependent on the condition of the glass surface and the amount of TiO₂. The crystal growth on the cut surface was faster than on the fractured surface and the growth rate in surface increased with increasing TiO₂. The phase separation found in NdAS glasses containing above 8 wt.% TiO₂, was confirmed to be an important factor controlling the internal crystallization process in Nd₂O₃–Al₂O₃–SiO₂–TiO₂ glasses.     

Dielectric Characteristics of Ceramics in BaO–Nd2O3–TiO2–Ta2O5 System

Dielectric ceramics in the BaO–Nd₂O₃–TiO₂–Ta₂O₅ system were prepared and characterized. The ceramics with tungsten–bronze structure based on the compositions Ba₂NdTi₂Ta₃O₁₅ and Ba₅NdTi₃Ta₇O₃₀ had a high dielectric constant (>100) with a lower frequency-dependency when complete densification was achieved; a low dielectric loss was obtained in the former.     

Crystallization of Glasses in the K2O–Nb2O5–SiO2System

The changes in the structure and phase composition of glasses in the K₂O–Nb₂O₅–SiO₂system upon their heat treatment in the temperature range 700–800°C are studied by the small-angle X-ray scattering (SAXS) technique and X-ray powder diffraction. It is demonstrated that the crystallization is the primary process giving rise to microinhomogeneities in glasses due to heat treatment. Nanocrystals of an unidentified niobium-containing phase precipitate in glasses with the formation of regions with a decreased content of potassium and niobium oxides. An increase in the duration of heat treatment at the studied temperatures results in an increase in the size of nanocrystals without change in their phase composition. This is accompanied by the disappearance of diffusion zones, which leads to a decrease in the SAXS intensity in the range of small scattering angles and, correspondingly, to a decrease in the light scattering intensity.     

Dielectric Relaxation in CaO–Bi2O3–B2O3 Glasses

Glasses in the system CaO–Bi₂O₃–B₂O₃ (in molar ratio) have been prepared using melt-quenching route. Ion transport characteristics were investigated for this glass using electric modulus, ac conductivity and impedance measurements. The ac conductivity was rationalized using Almond–West power law. Dielectric relaxation has been analyzed based on the behavior of electric modulus behavior. The activation energy associated with the electrical relaxation determined from the electric modulus spectra was found to be 1.76 eV, close to that the activation energy for dc conductivity (1.71 eV) indicating that the same species took part in both the processes. The stretched exponent β (0.5–0.6) is invariant with temperature for the present glasses.     

Bioactivity investigation of glass and glass ceramics in Li2O–SiO2–CaO–P2O5–CaF2 system

Abstract

Glass samples in Li₂O–SiO₂–CaO–P₂O₅–CaF₂ system with different contents of P₂O₅, CaO and CaF₂ in relative ratios responded to fluoroapatite (FA) composition (referred to P₂O₅ addition) have been prepared and heat treated at 550 and 750°C to obtain glass ceramics. Bioactivity of all samples has been proved in vitro by the presence of new layer of apatite-like phases formed after soaking in simulated body fluid (SBF). The development and the apatitic character of created layers have been demonstrated by Fourier transform infrared analysis. Scanning electron microscopy and electron probe microanalysis have demonstrated that the density and the thickness of new layer depend on P₂O₅ content, crystallisation temperature and immersion time. The bioactivity has been enhanced by P₂O₅ addition as well in the case of the base glasses as in the case of glass ceramics. The additional heat treatment appeared to inhibit the bioactive behaviour, though the longer SBF acting leads to the additional formation of apatite-like layer. The mechanical properties, expressed as Vicker hardness, have been found higher and increasing with P₂O₅ in glass ceramics treated at 750°C comparatively with base glass samples and the highest value of 7˙37 GPa has been achieved by 14 wt-%P₂O₅ addition. The same content of P₂O₅ in glass ceramics heat treated at 550°C resulted in a decrease in hardness to a minimum value from all samples. The increase and decrease in hardness responded to development and suppression of crystallisation respectively. The inhibition of crystallisation has been affected by the presence of 'amorphous' FA according to X-ray diffraction and differential thermal analysis results.     

Phase relations in ZrO2–La2 Zr2O7–Y2 Zr2O7system

Abstract

The phase relations in the system ZrO₂–La₂Zr₂O₇– Y₂Zr₂O₇ have been investigated using X-ray diffraction. Mixed oxide phase assemblages were prepared by hydrolysing zirconium butoxide with solutions of Y and La nitrates, followed by drying, calcining, and sintering. The cubic zirconia phase can accept into solid solution the larger, non-cubic stabilising lanthanum ion in the presence of a suitable proportion of the cubic stabilising oxide of yttrium. As the amount of the larger rare earth element ion is increased formation of pyrochlore and tetragonal type compounds is favoured.     

Large third-order optical nonlinearity of ZnO–Bi2O3–B2O3 glass–ceramic containing Bi2ZnB2O7 nanocrystals

Homogeneous transparent optical glass–ceramics precipitated with unique nonlinear crystals are promising materials for photonic applications. We have utilized heat treatment method to prepare transparent ZnO–Bi₂O₃–B₂O₃ glass–ceramic containing Bi₂ZnB₂O₇ nonlinear nanocrystals. A large third-order nonlinear susceptibility χ⁽³⁾ of glass–ceramic is measured by Z-scan technique, which mainly attributed to unique [BiO₆] and [B₂O₅] units in Bi₂ZnB₂O₇ crystal structure and the quantum size effect of nanoparticles. The discovery is of great potential in the application of nonlinear optical integrated devices.     

Antibacterial and photocatalytic active transparent TiO2 crystallized CaO–BaO–B2O3–Al2O3–TiO2–ZnO glass nanocomposites

Transparent TiO₂ crystallized 5CaO–10BaO–65B₂O₃–Al₂O₃–20TiO₂–10ZnO (CBBATZ) glass nanocomposites were fabricated using melt-quenching technique followed by specific heat treatments. As-quenched glass samples were provided three different heat treatments at 630°C for 3, 5, and 10 hours in order to obtain different amounts of TiO₂ nanocrystals in the glass. The presence of rutile phase of TiO₂ nanocrystals in glass was confirmed by X-ray diffraction. The glass nanocomposite heat treated for 10 hours showed a hydrophobic nature with contact angle of 90.90°. Contact angle decreased from 90.90 to 22.20°, when irradiated under ultraviolet (UV) radiation for 45 minutes. This photoinduced hydrophilicity showed a photocatalytic and self-cleaning properties of glass nanocomposite. During photocatalytic ink test, the maximum change in color of Resurin (Rz) ink and 60% degradation in absorbance of ink within 150 minutes under UV radiation were found for glass nanocomposite heat treated at 10 hours. Also, 78% degradation in absorbance of methylene blue dye (pollutant) within 180 minutes under UV irradiation was found for glass naocomposite heat-treated at 10 hours. Antibacterial performance of transparent glass nanocomposite against Escherichia coli was evaluated as well. More than 95% of the bacterial cells were degraded with glass nanocomposite heat-treated at 10 hours. CBBATZ glass nanocomposite found to impart the antibacterial effect through generation of reactive oxygen species (ROS) in aqueous medium. ROS species which was confirmed in the bacterial cell through intracellular ROS generation kit. During evaluation of mechanical properties using nanoindentation technique, the values of hardness and reduced modulus increased by ~26% and 10%, respectively, for glass nanocomposite heat-treated at 10 hours as compared to as-quenched glass.     

Thermal Stability and Crystallization Kinetics of MgO–Al2O3–B2O3–SiO2 Glasses

To support commercialization of the MgO–Al₂O₃–B₂O–SiO₂-based low-dielectric glass fibers, crystallization characteristics of the relevant glasses was investigated under various heat-treatment conditions. The study focused on the effects of iron on the related thermal properties and crystallization kinetics. Both air-cooled and nucleation-treated samples were characterized by using the differential thermal analysis/differential scanning calorimeter method between room temperature and 1200°C. A collected set of properties covers glass transition temperature (T_g), maximum crystallization temperature (T_p), specific heat (ΔC_p), enthalpy of crystallization (ΔH_cryst), and thermal stability (ΔT=T_p—T_g). Using the Kinssiger method, the activation energy of crystallization was determined. Crystalline phases in the samples having various thermal histories were determined using powder X-ray diffraction (XRD) and/or in situ high-temperature XRD method. Selective scanning electron microscope/energy-dispersive spectroscopy analysis provided evidence that crystal density in the glass is affected by the iron concentration. Glass network structures, for air-cooled and heat-treated samples, were examined using a midinfrared spectroscopic method. Combining all of the results from our study, iron in glass is believed to function as a nucleation agent enhancing crystal population density in the melt without altering a primary phase field. By comparing the XRD data of the glasses in two forms (bulk versus powder), the following conclusions can be reached. The low-dielectric glass melt in commercial operation should be resistant to crystallization above 1100°C. Microscopic amorphous phase separation, possibly a borate-enriched phase separating from the silicate-enriched continuous phase can occur only if the melt is held at temperatures below 1100°C, that is, below the glass immiscibility temperature. The study concludes that neither crystallization nor amorphous phase separation will be expected for drawing fibers between 1200°C and 1300°C in a commercial operation.     

Application of BaO–CaO–Al2O3–B2O3–SiO2 glass–ceramic seals in large size planar IT-SOFC

BaO–CaO–Al₂O₃–B₂O₃–SiO₂ (BCAS) glass–ceramics can be used as sealant for large size planar anode-supported solid oxide fuel cells (SOFCs). BCAS glass–ceramics after heat treatment for different times were characterized by means of thermal dilatometer, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the coefficients of thermal expansion (CTE) of BCAS glass–ceramics are 11.4×10⁻⁶ K⁻¹, 11.3×10⁻⁶ K⁻¹ and 11.2×10⁻⁶ K⁻¹ after heated at 750 °C for 0 h, 50 h, and 100 h, respectively. The CTE of BCAS matches that of YSZ, Ni–YSZ and the interconnection of SOFC. Needle-like barium silicate, barium calcium silicate and hexacelsian are crystallized in the BCAS glass after heat-treatment for above 50 h at 750 °C. The glass–ceramics green tape prepared by aqueous tape casting can be directly applied in sealing the cell of SOFCs with 10 cm×10 cm. The open circuit voltage (OCV) of the cell keeps 1.19 V after running for 280 h at 750 °C and thermal cycling 10 times from 750 °C to room temperature. The maximum power density is 0.42 W/cm² using pure H₂ as fuel and air as oxidation gas. SEM images show no cracks or pores exist in the interface of BCAS glass–ceramics and the cell.     

Silver Co-Firable ZnTiNb2O8 Microwave Dielectric Ceramics with Li2O–ZnO–B2O3 Glass Additive

The effects of Li₂O–ZnO–B₂O₃ glass additive on the sintering behavior, phase formation, microstructure, and microwave dielectric properties of ZnTiNb₂O₈ ceramics have been investigated. The sintering temperature of ZnTiNb₂O₈ ceramics can be effectively reduced from 1200°C to 875°C by adding a small amount of Li₂O–ZnO–B₂O₃ glass, while no obvious degradation of the microwave dielectric properties was induced. Typically, the 2.0 wt% Li₂O–ZnO–B₂O₃ glass-added ceramic sintered at 875°C has better microwave dielectric properties of ɛ_r=31.8, Q×f=25,013 GHz, and τ_f=−62 ppm/°C. In addition, the ceramics can be co-fired well with an Ag electrode.     

Joining MgAl2O4 ceramics using ZnO–Al2O3–SiO2 glass ceramic with precipitated ZnAl2O4

In this work, crystallization, thermal expansion and wetting behavior of ZnO–Al₂O₃–SiO₂ (ZAS) glass were first investigated. The results showed that ZnAl₂O₄ was precipitated from ZAS glass after crystallization treatment. Crystallization increased the coefficient of thermal expansion (CTE) of ZAS glass ceramic due to the high CTE of ZnAl₂O₄. In addition, ZAS glass exhibited good wettability on the surface of MgAl₂O₄ substrate. On this basis, ZAS glass was used to join MgAl₂O₄ ceramic, and the microstructure and mechanical properties of joints obtained with different cooling methods were investigated. The flexural strength of joints was related to the content of ZnAl₂O₄ crystals in the brazing seams. Additional nucleation and crystallization treatment during cooling process improved the crystallinity of brazing seam, resulting in better matching of the CTE of brazing seam with that of MgAl₂O₄ ceramic. The maximum flexural strength of joints reached 201 MPa, which was equivalent to the strength of MgAl₂O₄ ceramic.     

Effect of Al2O3 content on BaO–Al2O3–B2O3–SiO2 glass sealant for solid oxide fuel cell

The glass structure, wetting behavior and crystallization of BaO–Al₂O₃–B₂O₃–SiO₂ system glass containing 2–10 mol% Al₂O₃ were investigated. The introduction of Al₂O₃ caused the conversion of [BO₃] units and [BO₄] units to each other and it played as glass network former when the content was up to 10 mol%, accompanied by [BO₄] → [BO₃]. The stability of the glass improved first and then decreased as Al₂O₃ increased from 2 to 10 mol%, the glass with 5 mol% Al₂O₃ being the most stable one. The wetting behavior of the glasses indicates that excess Al₂O₃ leads to high sealing temperature. The glass containing 5 mol% Al₂O₃ characterized by a lower sealing temperature is suitable for SOFC sealing. Al₂O₃ improves the crystallization temperature of the glass. The crystal phases in the reheated glasses are mainly composed of Ba₂Si₃O₈, BaSiO₃, BaB₂O₄ and BaAl₂Si₂O₈. Al₂O₃ helps the crystallization of BaSiO₃ and BaAl₂Si₂O₈.     

A Significant Role of Tb2O3 on the Optical Properties and Radiation Shielding Performance of Ga2O3–B2O3–Al2O3–GeO2 Glasses

Journal of Inorganic and Organometallic Polymers and Materials - This research article focuses on the significant role of Tb2O3 content on the optical properties and radiation shielding performance...     

Effect of Sb_2O_3 Replace V_2O_5 on the Electronic Property of V2O5–P2O5–Sb2O3–Bi2O3 Glass System

采用体积电阻率法、红外光谱、X射线衍射研究了V2O5–P2O5–Sb2O3–Bi2O3体系玻璃的电性能、结构和析晶状况。结果表明：随着Sb2O3取代部分V2O5,玻璃的体积电阻率显著升高,电子分别以V4＋和V5＋为中心不停地进行电子跃迁的电子导电特征得到明显抑制,15%Sb2O3、20%Sb2O3玻璃的体积电阻率可以达到实用水平。当Sb2O3取代V2O5进入钒酸盐玻璃中,玻璃结构得到增强,析晶状况得到改善,削弱了玻璃的导电能力。     

Calculation of the Viscosity of Glass-Forming Melts: VI. The R2O–B2O3–SiO2and RO–B2O3–SiO2Ternary Borosilicate Systems

A method for calculating the viscosity from composition and temperature for melts in the R _m O _n –B₂O₃–SiO₂systems is proposed. The change in the concentrations of structural groups depending on the melt composition is taken into account in calculations. The results of calculations are compared with the experimental data available in the literature on the viscosity of 1200 melts with the use of the SciGlass information system. The root-mean-square deviation between the experimental and calculated characteristic temperatures varies from 30 K (for the glass transition temperature and the Littleton point) to 50 K (for a viscosity of 10⁴P).